Manual for PIX 506E?

Hi everyone! I just became in charge of a PIX 506E, which I have no experience with. I was not told how it was set up, what the password is, etc...Oh, and the dongle for the console connection is non-existent as well.
On Cisco's website, I can't find any manuals for it. The only documentation I could find was a quick setup guide, which is not helpful at all if it is already set up.
Basically, I am looking for any help anyone can provide so that I can get into the interface for the PIX 506E so I can see how things are set up and to change things in the future. Thank you in advance!

This could be a long journey or a short one, but for sake to help you here we go..
When I say long journey it is because all depends on what type of resources you have at hand, at least you have us in netpro, but more specifically if you do not know the admin password for the PIX that is number one headache, you need password recovery procedure, please try to make an effort to obtain the password to not go through all these procedures, if you cannot then you need password recovery .
See password recovery.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_password_recovery09186a008009478b.shtml
Please have handy these tools
1- Console cable to connect to COM port in PC and PIX console port
2- Terminal emulator - hyperterminal
3- Mini hub to connect your PC and pix pysical interface to it
4- tftp server software running on your PC
Follow instructions on link.
As for instructions about the PIX there are hundreds of documentation in Cisco website, we can direct you to them but first you need to gain access to PIX.
HTH
-Jorge

Similar Messages

ISAKMP spi size buffer overflow for PIX 506e

Hello,
We have perform a vulnerability scan for our network and found a high risk vulnerability result as stated below:
"H IsakmpSpiSizeBo: ISAKMP spi size buffer overflow
Additional Information More Information
Internet Security Association and Key Management Protocol (ISAKMP) is a key exchange protocol signature. ISAKMP is vulnerable to a
buffer overflow. A remote attacker can send a specially-crafted ISAKMP payload to a vulnerable VPN client or server to overflow a buffer
and execute arbitrary code on the system, possibly with administrative privileges.
The supported operating systems in the Platforms Affected list are only vulnerable if they use the LibKmp ISAKMP library. Only VPN
or firewall products which implement the Entrust LibKmp ISAKMP library are vulnerable.
Remedy:
Apply the appropriate hotfix for this vulnerability, as listed in the Symantec Security Response SYM04-012 and available from the
Symantec FTP Update Web site. See References."
I have search it on cisco but found no clue on resolving the issue. Our firewall is PIX 506E model.
Your inputs are highly appreciated.
Thank you
Neil

The cause of the issue was the remote peer, the parameters of phase 2 were wrong

Pix 506e firewall configring for mail( Exhange), Web, FTP server

Hi
I am Hemant, We have pix 506e firewall, D-link ADSL dsl-502t and my IBM xseries 236 server.
I have fix static live ip 59.181.103.220 which i have got ISP (MTNL), and the same ip is given in fqdn in www.net4india.com (a company from where we have registered domaim name and taken space)
My problem is i am not able to send mail through my mail server (loyalindia.co.in)but i am receiving mails from any server.
My network design is as fallows:-
ADSL (WAN)59.181.103.220, ADSL (LAN)59.181.103.221. Pix 506e (out) 59.181.103.222, Pix 506e (in) 192.168.1.1. My domain mail server loyalindia.co.in (Exchange server) ip 192.168.1.2
I am tryied with (ADSL)natting and without natting but the problem is same.
If i am removing the pix 506e and directly connecting the server to adsl i am able to receive and send mails properly.
can anybody who can support me?.

Hello
I think there won't be one QUCK START to get all of this up and running, there are multiple examples on the following page, a few that might help would be:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/prod_configuration_examples_list.html
PIX/ASA : Connecting Three Internal Networks with Internet Configuration Example
PIX/ASA : Connecting Two Internal Networks with Internet Configuration Example
ASA 7.x/PIX 6.x and Above: Open/Block the Ports Configuration Example
PIX/ASA 7.x: Enable VoIP (SIP, MGCP, H323, SCCP) Services Configuration Example
PIX/ASA 7.x and FWSM: NAT and PAT Statements
PIX/ASA 7.x and later : Port Redirection(Forwarding) with nat, global, static and access-list Commands
Configuring PIX Firewall with Mail Server Access on the DMZ
Configuring the PIX Firewall with Mail Server Access on Inside Network
Please rate if you find the post helpful.
Regards
Farrukh

Linksys WRT600N vs CISCO PIX 506E.... Firewall / Routing Performance

Hi:
I am new to the forum and was hoping to tap into some of your expertise. I have a Linksys WRT600N version 1.1 and I recently acquired a CISCO PIX 506E firewall. My question is what should I use as a firewall? Both have SPI etc. Should I:
a) Use the 506E as a firewall and use the 600 as a wireless access point, or
b) Use the 600 as a firewall and wireless access point.
Do both routers have the same firewall routing performance? I want to use the storage feautre on the 600N, but if I do that and use it as a wireless access point the 600 can't get the proper time from the Internet, so my time for newly created folders and files shows they are 10 years old.
Anyway, just thought I would post and find out what some of the experts thought and maybe someone from Linksys or CISCO. I know the 506E is discontinued and was manufactured around 2001 and the 600N is a new model.
(Edited subject to keep threads from stretching. Thanks!)
Message Edited by JOHNDOE_06 on 05-06-2008 10:41 AM

The PIX is a real firewall. The WRT has a firewall which mostly protects the router itself. People prefer to buy a "SPI firewall router" instead of a simple "router" even though the router firewall does nothing or little to protect the LAN. The only firewall configurations on the WRTs you can usually do is on the Access Restrictions tab. But that's usually all. The LAN itself is not protected by the firewall. You would notice this if you had a public IP subnet and ran it through the WRT: the LAN would be fully exposed to the internet. Some routers have a few functions like protection against denial of service attacks or similar. But even then this often filters only the traffic targeted at the router and not the LAN.
The common protection of your LAN you have on the WRT is because you use private IP addresses inside your LAN and the router does NAT. However, NAT is not a security mechanism but a mechanism to solve the problem that you can only have a single public IP address but want to use multiple computers, which is why you have to use private IP addresses. Current NAT implementations usually drop unsolicited incoming traffic because they don't know to which IP address in the LAN to send it to. But the notion of NAT is to deliver and to allow connectivity. This has nothing to do with security or a firewall.
Thus, if you want to use a real firewall use the PIX. On the PIX you can configure the traffic which is allowed to enter the LAN and which not. It is far superior in this respect to the WRT. However, as it is a older model, I cannot tell how fast the PIX is. You should be able to find the old data sheets of the PIX somewhere on the cisco website. They should mention the possible throughput. I guess it won't be an issue.
To me another point for the PIX are the VPN capabilities which allow you to securely access your LAN while you are on the road.
Of course, you must know how to configure the PIX correctly. It is a complex device and can be configured pretty much for anything you like. This means of course if you do it wrong you may end up with little or no security.
BTW, there are no people from linksys in this forums except the moderators (which may be from lithium). To hear from Linksys you have to contact Linksys support.

PIX 506E routes died

Hello experts...
I've had a set of PIX 506E boxes holding an IPSEC tunnel for a good year or so without a hitch. Today, the tunnel dropped and I lost access to the remote site. The local PIX can only ping devices on the local [inside] subnet and all nodes on all my other subnets can't find a route to the PIX. On the local gateway, I can ping the PIX, but can't traceroute to it. I also ran an ICMP debug and could see when remote nodes ping, but the reply doesn't leave the box.
Nothing has changed, routes all look good, i've reset everything -- no luck at all. Any idea what may be happening? I have a feeling it's a basic issue that looks more complex that it is, but i'm stumped at this point.
Any help would be greatly appreciated!
Thanks,
Jad

Use this Cisco PIX 500 Series Security Appliances Troubleshoot and Alerts
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/tsd_products_support_troubleshoot_and_alerts.html

CiscoView 5.4 Support for PIX 515

I have just installed CiscoWorks2000 and am having trouble opening CiscoView for my PIX-515. I read in the documentation that it is supported, (I think). Anyway I receive an error which states:
CiscoView Error
Can't Find Applicable device package for "device name".
Thanks,
Sabin

Currently the latest CV 5.3/5.4 device package v3-0 for PIX only supports PIX 501, 506 and 506E models. PIX 515 support is not yet available in CV: http://www.cisco.com/cgi-bin/Software/CiscoView/cvplanner.cgi

Pix 506e as Content Filter

Is there any way to effectively use a Pix 506e as a content filter? I see some example configurations involving an ASA 5500, but I was wondering if the pix alone will allow content filtering. We are a small business that is looking to restrict just a few websites to our DHCP users. (i.e. eBay, yahoo mail, Amazon). We already have the pix. Thanks!

Suppose if you want to filter streaming media content with PIX 506E, you have two options. The first one is to block ports on the PIX and the second is to use Proxy Server to filter URLs. Since our main concern is doing it on the PIX, You may enter these commands on the PIX for well-known ports that you could block on the firewall:
access-list nostream deny udp any any eq 2979
access-list nostream deny udp any any eq 1790
access-list nostream deny udp any any eq 1755
access-list nostream deny udp any any eq 1736
access-list nostream deny udp any any eq 554
access-list nostream deny udp any any eq 537
access-list nostream deny tcp any any eq 2979
access-list nostream deny tcp any any eq 1790
access-list nostream deny tcp any any eq 1755
access-list nostream deny tcp any any eq 1736
access-list nostream deny tcp any any eq 554
access-list nostream deny tcp any any eq 537
access-list nostream permit tcp any any eq 80
access-list nostream permit ip any any
access-group nostream in interface inside
However, some streaming applications use random ports using auto-configure options that are difficult to block with the PIX. To resolve this issue, you have the second option, using a proxy server to filter the URLs. You may use Websense and any other software to filter web traffic.

Pix 506e

Hi,
We have planning to Purchase Cisco Pix 506E Firewall. We are having 50
Computers & Users.If we purchase Pix 506E Firewall,its require to purchase
any aditional license.
with regds
prem

For the PIX 506E there is only one license that can be purchased which is the 3DES/AES and DES Encryption Licenses. Right now I think you can download that license for free. The following link will provide you with details on that license and the data sheet on that PIX (scroll down about half way for the license information).
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b13.html
The following link will give you the data sheet and describe the three different licenses available with upper models of the PIX as it relates to the 515E (restricted, unrestricted, and failover).
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b15.html

Where can i find a dutch manual for photoshop cs6

Hi,
I'm trying to find the dutch manual for Photoshop CS6.
There is a hyperlink available on this page Help bij Photoshop | Archief called Help bij Adobe Photoshop CS5 (PDF), but if I follow this I end up on an "error page" in English telling me that the requested page isn't available.
Can someone provide me with this PDF-file please?
I can download this PDF in English, but it would be so much easier for me to read and understand the subject matter in Dutch.
So, is there anybody out there who can send it to me?
Thanks!
Michael

You should ask in Photoshop General Discussion
This forum is about the Cloud as a delivery process, not about using individual programs
If you start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll

Open Interface manual for HRMS

Hi,
Where can I get open interface manual for oracle HRMS.
Regards,
Soham

Soham,
Can you be more specific in what you want. Oracle HRMS supports a very broad, diverse range of data that can very significantly from one customer to another. There are seeded interfaces in HRMS along with extract tools and supported APIs. See the following for a starting point:
Note: 368845.1 - Oracle Generic Third Party Payroll Backfeed and bfexampl.xls
Note: 228527.1 - Web ADI for Oracle HRMS Implementation and Configuration
Note: 358187.1 - Integration Guide for Oracle Human Resources Release 11i and Ceridian Source 500
Note: 358184.1 - Integration Guide for Oracle Human Resources Release 11i and ADP
Note: 216838.1 - Oracle HRMS Product Family Publicly Callable Business Process APIs (A Reference Consolidation)
Note: 226744.1 - Cash Management Payroll Integration Release 11i
Note: 367395.1 - System Extract Focus Area
Note: 227537.1 - Windstar International Tax Navigator Interface Version 12
Note: 227482.1 - Payment of Child Support Through Electronic Funds Transfer (EFT)
Release 11.03 & 11i
Regards,
Greg

Where can I find an oline manual for Mail for Mavericks?

I am looking for an oline manual for Mail for Mavericks to learn about its featires/functionality before I switch to the MAC. Is there such a manual and if so, please share a link (I could not locate it). Thanks.

There is this online resource: https://www.apple.com/support/mac-apps/mail/

How can I sync my photo contents in iPhoto on my iMac to my new iPAD's iPhoto? I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but I cannot find "phone button" under Device name on iTunes page. Please help! Thanks!

I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but after physically connecting iPAD with iMac with USB or via WiFi I still cannot find "phone button" under Device name on iTunes page. Please help! Thanks!
I have been creating a photo book using a lots of photographs on iPhoto, and then I took another photos by using new iPAD which I want to integrate with the original album/book on iMac. I was able to import them from iPAD's iPhoto to iMac's iPhoto. However I cannot import or transfer or sync anything from iMac's iPhoto to that of my iPAD.
So my iPhoto page on iPAD contains only 3 or 4 newly created albums, and no other info. That means no syncing....
I am supposed to be able to work on this project on either of these iPAD and iMac, correct?
I am puzzled. I appreciate for your advice and help.
Thank you!

It doesn't appear under the iPad device on the left-hand sidebar of iTunes, you need to select the iPad device on the sidebar and then select the Photos tab on the right-hand side of iTunes e.g.
And then on the right-hand side :

Automatic Conversion of PR to PO.. Need User Manual for ME59 T code

Hai Sap Gurus,
I Got the following content from net. but kindly help me by sending me user manual for ME59.
You created purchase requisition for various material. During creation of purchase order you used the following path:
Purchase Requisition
.......Follow on function
.........Create Purchase Order
............automatic via purReq.
When you mentioned required purchase requisition number and execute, system give error that purchase requisition does not contain any suitable item.
Is there any setting in customization where you can monitor and use that function.
In an effort for you to successfully use the Transaction Code ME59 to automatically convert the current PR into PO, then the following criteria should be met:
1) In the Purchasing View of the material master data, the "Autom. PO" field must be clicked;
2) In the Purchasing View of the Vendor Master Data, the "Automatic Purchase Order" field must be clicked;
3) The Outline Agreement or Purchasing Info Record shall be maintained which will allow the automatic copying of unit price and other conditions into PO;
4) The Source List shall be maintained for the nominated vendor which was shown in either the Outline Agreement or Purchasing Info Record.
or
it might be PR subject to release strategy and not yet released
or
If you're not using a source list or automatic creation of PO, you may need to assign the requisition to a purchase information record using transaction ME56. Then it should appear in ME58
Thanks.. Reply me pls...
Edited by: Swetha SAP Girl on Jun 18, 2009 2:19 PM

Hi,
Step by step process for automatic PO creation from PR
1. Tick check box in purchasing view of Material Master(MM01/MM02)
2. Tick check box for auto PO in purchaisng data of Vendor Master record (MK02)
3.   Maintain Source list for Material,plant and Vendor combination in ME01
4.   In ME51N create PR and assign source of supply in "Source of supply" tab
5.   In ME59N key in Purchaisng Org., Vendor and Plant - execute
You will get POs created with reference to PR automatically.
Hope its clear
Regards,
Uzair Hussain

Manual for creation of new Plant in SAP

Hi Members,
I need to test in quality finance related activities, creation of Profit center, Cost center, Standard Heirarchy, etc.. Does anyone help me with the manual for role of Finance guy in creation of new Plant..
Rgrds,
Ravi

Hi Ravi,
Please find the below link for steps to create plant with screens.
http://www.saponlinetutorials.com/how-to-create-plant-in-sap-mm-define-plant/
BR, Srinivas Salpala

Can i print out the manual for ipod mini in different language?

hi i wanna get an ipod mini for my mom and she doesnt really speak or read enlgish all that well, i mean ill gladly help her out, but i want her to have some sort of manual in case im not around, she speaks russian and i was wondering if i can get a russian manual for ipod mini or atlest some sort of quick start guide

Are we really talking about the old iPod mini, or the current small iPod, the iPod nano ?
Here are the manuals available online for the iPod mini. The language options are listed.
http://support.apple.com/manuals/#ipodmini

Manual for PIX 506E?

Similar Messages

Maybe you are looking for