MDBT : MRP RUN Problem

I have one storeage locaion  for which i want to tun MRP run in backgruond .
Now i have cerated MRP area (STORE) as stoarge location asssigne th erespective storge location there.
Now i created  scop of planning & i assigne tthat MRP area as "STORE"to scope of planning.
Now cerated varaint as "CONSUMPTION"and in scope of plalning i selcetd the scope of planing as my MRP area  and saved the variant .
Now all material under this area are cinsumption baed material means everyone has MRP type as VB, reordre point and lot siza as HB, max lot qty  and STORE as MRP area in material master.
NOw in MDBT i selcted the variant and click on start inmmediate i m getting mesage as "Request with variant CONSUMPTION Started"
If i see MD04 til no requirenment is genrtaed with this Run ??
1. Please tel ..where i ned to corect
2. Is there any mesage after background MRP executed ;like in MD02 planning result screen .

Dear,
Please check whether planning file entry exists in MD21 also check MDAB & MDRE ?
or run program RMMRP000.
Please note With MRP type VB (Manual Reorder Point Planing) system will not consider Dependent requirement or any other reservation.
It will take care about only Reorder point.
If You have set reorder point of 100 Nos.
And dependent requirement is of 35 Nos , and available stock is 90 Nos. then at the time of MRP run system will generate PR of 10 Nos only just to cover that less qty than the reorder point of 100 Nos.So there is nothing wrong in your case.
If you want to concider Dependent requirement also during Planing run then you have to change MRP type VB to PD then check.
Regards,
R.brahmankar

Similar Messages

  • MRP run problem

    Hi experts,
    During MRP run for a material , open PO quantity is not considered If delivery date mentioned in that open PO exceeds 110 days from planning date(MRP run date). If it is less , it considers open PO quantity.
    MRP type = V1 (Reorder point planning)
    Lot size = HB
    planned delivery time = 0 days
    What could be the reason for it? Pls help me out.
    Thanks in advance,
    Rgds,
    jay

    When u keep your planning horizon 100 and in MD02 if ur using NETCH planning then system will consider the planning in between 100 days only If your open PO in out of planning horizon then it will not consider for the same.
    If u want to do the same u have to go for increase ur planning horizon time in OPPQ.
    whatever u required.
    Kind Regards,
    Nilesh

  • MRP Run Problem With Shipment Notification

    Hi Experts,
    Issue
    In MD04 i have 1 shipment Notification,but after MRP Run it should get display in MD05 but in my case it is not happening.CAn anybody tell me the possible causes / reasons why this is happeinig.
    Awiitng for your quick response
    Need any furher inputs please revert back to me immediately.
    Cheers,
    Kumar.S

    Hi karthik,
    Thanks for your reply,even i know Md04 is Dynamic and MD05 is static,also i cant able to clearly understtood what u r telling,
    Kindly check whether shipment notification is updated during the 2nd run then it wont reflect in MD05
    but when i check the same scenario in Q shipment notification getiing updated but not in prdn.
    Pls clarify
    Cheers,
    Kumar.S

  • MRP running problem

    Hi gurus,
    When i try to run the total MRP in MD01, i can see that only certain material is being run, and most of it are not run.
    So, when i go to MD05 to view the MRP list, i can see that the material is still in old date MRP run date where the stock qty is wrong.
    I tried to go to MD02 to run that particular material, then that material is updated accordingly.
    Any one has any idea what had happen?
    Why when I run in Md01 some material is not picking to be run?
    Thanks!

    I've check in MR21, i found that planning file entry is there. But i can see some of the material that is not run do not have NETCH set.
    How do i make the material as NETCH set so that when i run the MRP in MD01 it can run it as well?
    Infact i try to create the planning file thru MD20 the entry is created but most of are not set as NETCH, why it can happen in such a way? (My processing key is NETCH when run MD01)
    Does it mean all the materials must have set as NETCH then only it can run the MRP?
    But i found some of the material do not have the NETCH set but when i try the total MRP run in MD01 it still can works?
    What is the reason behind?
    Please help, thanks!

  • MRP Run Problem through MDBT

    Hi,
    We are running the MRP based on MRP controller through Transaction MDBT.
    As per SAP threads, We insert the User Exit Key as CB1 & User exit parameters as MRP Controller and click on start immediately.
    After result come, we see the output from SP02 transaction.
    There all the materials showing with 8 number exception (Terminations), means all the material's having the Deletion Indicator when i am seeing in MARC table against that MRP Controller - CB1.
    Please tell me how only deletion material's showing. How other material's will display, which display in MARC table except Deletion Indicator.
    Plz guide...

    Hi Kundan,
    STAD to trace combination of User and Tcode, but particular material its diffcult to trace in std sap.
    If you want to trace then you need do some enhancements, create customized table (mateial number, plant, date, time, etc) for when user run the mrp in MD02 then save all data's to your own table.
    I hope this will help to you
    Regards,
    Sankaran

  • MRP run problem in TCode-MD01

    hi experts,
    There were some MRP controllers were assigned for User exit in SPRO for planning run (T code :- MD01 ). Now i have defined additional MRP controllers and also assigned them for user exit (in SPRO) for planning run.
    With old MRP controllers defined as user exits , Planning run is considering materials with only particular MRP controller.
    But for these newly defined MRP controllers , user exit is not restricting planning of materials with only particular MRP controller and materials planning is carried out for all materials with newly defined MRP controllers.
    please help me out
    thanks in advance
    rgds.
    jai

    The name of the extension where you can find the user exit is M61X0001
    You have to read the code to find out why it is not working for the new controllers.
    Probably the code is not that dynamic as you thought and the controllers are hardcoded ...

  • Elaborate in MDBT and open scheduling agreement list through MRP Run

    Hi experts,
    After MRP Run in MD02 i had find out the list of Purchase requisition at ME5A , based on the purchase requisition no i will create scheduling agreement  not for PO, so how it is possible for the list of open scheduling agreement list  through MRP Run Only?
    Kindly elaborate the screen short steps at MDBT - MRP Run in background process what are possibilities >  weekly once or daily basis, report run repeated purchase requisition  no or not , update the daily stock status all those things ?
           what are the possibles in MDBT MRP Run > Maintain conditions,type of generate reports, open reports through t.code and report converted   excel or through mail recording MRP  run?
    Thanks,
    Umapathy

    Hi,
    In MDBT we can create the variant and Schedule as you wish  and execute .and also you can have the status of the schedule whether it is in cancelled or finished .
    Reg
    MSP

  • Problem with Back ground MRP Run (MDBT) or MD01

    Hello SAP Experts,
    Issue :- Material is not considering during Automatic back ground MRP run ( MDBT or MD01)
    But when we run MRP in forground (MD02) system is considering the material.
    we have checked both the selection parameter are same for MD01 and MD02 .
    can you help us on this issue ?
    Regards
    Mahesh

    Hi,
    Problem is due to entry in Planing File is missing for that Material.
    Go to MD21 and check whether Planing File entry is maintain for that Materiel.
    If not then maintain it by T.code MD20 (Manual) or you can do it by using back Ground JOB - OMDU.
    Regards,
    Dhaval

  • MRP run with MDBT

    Hi all,
    I'm facing a typcial problem
    In MDBT -processing key is maintained as NETPL
    There are 3 materials say
    1.A
    2.B
    3.C
    For all three materials NETCH is marked in the planning file entry & NETPL is blank in MD21
    When i go for MRP run via MDBT then no proposal is raised for A & B,where as for C i'm getting a proposal
    All three has requirement -Exected result is Planned order
    Initially i thought NETPL is not active in MD21 & that is the reason i'm not getting any proposal
    but i'm shocked to see proposal for material C
    MRP is run with processing NETPL
    Will the material marked for NETCH also be included in the run or only those materials which are marked for NETPL only will be included ?
    If yes for 1st question then i feel there is a logical difference
    If yes for 2nd question then why should i get proposal for material C?
    Please clarify me
    SVP
    Guys pls respond
    Edited by: SVP on Jan 8, 2009 3:55 PM

    Hi Vishal,
    Thanks for pointing out user exit key,i didnt noticed that,In one the variants user exit key is maintained ,MRP controller selection (CTL)
    & user exit paramter also is maintained as 100 in one variant & in another as 001-099,101-500
    How is this normally defined?What doen tis mean
    In first case(100) does it mean that run only for thos matrials which have MRP controller as "100"
    In second case rund for all materials with MRp controller (001-0990 & 101 to 500 I'm not usre on this
    If yes pls let me know where we define this whole thing
    Like MRP controller selection is defined as CTL -but what does it mean,where are the actual conidtions written
    Very basic question may be but i'm not aware fo this,pls let me know
    Once again thanks a lot for giving the lead
    SVP

  • When MRP run through background process in MDBT open PR and PO not comming?

    Hi,
    When MRP run through backgroung process in MDBT open PR and PO not coming in MDBT result.
    Pls advise accordingaly.
    Regards
    rk

    Ram,
    Either I am totally misunderstanding your statements, or your business people are misinformed.  
    The output of MD01 (MRP total run in foreground) and the output of MDBT (MRP total Run in Background) ARE IDENTICAL, provided you have selected the same parameters.  
    Neither output contains a discrete listing of open Purchase orders and Purchase requisitions.
    Standard output of both MD01 and MDBT are:
    1.  List of materials processed, with exception messages
    2.  Statistics
    In addition, both of these programs also write MRP records to the MRP databases, provided that the "Display Material List" parameter is set.  In this case, both of these programs will produce data that can be further reviewed and managed in MD05 and MD06. MD06 is the tool that most planners use to process the MRP database info.
    If you wish to see a listing of the entire MRP results (either MD01 or MDBT), then execute transaction MDLD.  This will produce either a spoolfile or a printed document.
    For the PO or PR listings, review my earlier suggestions.
    Rgds,
    DB49

  • Any difference setting background MRP run in MDBT and SM37

    Hello,
    Just wander if there is any differences setting up MRP run in MDBT or in SM37 to run RMMRP000?  This is to run MRP at plant level in background.
    Thanks,
    Lin-Lin

    Hi,.
    Both MDBT & SM37 are having same program (SAPLBTCH) . MDBT is <b>Foreground</b> job as well as <b>Background job.</b>
    SM37 is only for <b>Background job</b> only.
    Pls let me know any further clarification.
    regards,
    Mohan
    Message was edited by:
            Mohan Ramalingam

  • USer Exit/BADI  for Purchase requisition creation in MDBT or WC27 /MRP Run

    I am looking for an enhancement where a purchase req is created during MRP Run in the background ( MDBT or WC27 or program - RMMRP000 .
    Any suggestions would be welcome.

    Hi,
    try the exits:
    LMDR2001  User exits restr. profiles of opt. pur.ord.
    LMDZU001  User exits in additional planning
    Regards,
    Renjith Michael.

  • Problem with MRP running

    Hello Gurus,
    i have a problem with my product. lets take an example. my semifinished product abc is made up of a, b and c.
    i have made them(abc, a, b and c) to use MRP type VB. i made palnning file entry and BOM and then i run the MRP.
    I run single item multilevel MRP for semi-finished product abc, it showed me result in MRP running only for abc but not for a, b and c.
    can u please tell me where i am making any mistake.
    regards

    Hi Maggi,
    If you have used mrp run for single item,single level  planning (ie) md03, it will plan only for that particular material & will not plan for the dependent material in the BOM.
    If you run with t.code md02, MRP run for single item,multi level, all the dependent requirements will be planned.
    Also VB is for reorder point planning. ie if you maint reorder level as 100 for a,b & c materials & if the stock goes below 100, say  50 Nos. for all the three material. Then procurement proposal(Pur req) will be created for 50 nos for all the material(a,b,c).
    If you use MRP type PD, there is no question of reorder level, during mrp run system check the stock of the dependent requirements. If there is a shortage procurement proposal are created.
    Regards,
    Senthilkumar SD

  • Problem during MRP RUN.

    HELLO, FRIENDS,
    if i select mixed MRP in the material master with indicator 2 i.e.gross reqirement
    for MRP run ,but after taking MRP run through md01 .its not exploding dependent requirement of its component.Is there any setting for this?
    lpease give solution
    regards,]mangesh

    Hi,
    Check with t.code CS11 & check the result whether BOM is exploding or not.
    Then check in t.code OS23, whether mrp exlosion is activated or not.
    Check the BOM usage used while creating the BOM.
    Regards,
    Senthilkumar

  • Alternative BOM problem in MRP run

    Hello Experts,
    We have two BOM for one material.Now I want to use BOM-1 for MRP run & BOM-2 for subcontracting.I have maintined following settings.
    1) Production version.
    2) BOM explosion selection method in MRP4 -2
    3) Assign PV in inforecord for subcontracting.
    4) Assign PV in MD61 in schedule line .
    But when I run MRP it still consider subcontracting BOM.Have I missed any setting?
    Kindly guide.Thanks you.

    Hi, Follow the below process,
    1.Enter the BOM selection method as 2 in the MRP4 view of the material master.
    2.In case if you have not assigned the production version in MD61 against the PIR's under schedule line
    tab key (in the top menu click on settings and prod version ,then you can assign the prod version which
    you need to pick during the MRP run),the system always picksup the first production version during
    MRP run even if all the prod versions contains the same validity dates and lot sizes.
    3.If you are not willing to assign the prod version in MD61 ,but the system should consider the second
    prod version for MRP run means,then set the locked status for the first prod.version.
    4.When run MRP via MD02 or MD50 in the simulation mode.(i.e w/o giving tick in simulation mode).
    Click on Save,You will get a pop screen,
    Now click on the continue icon, Then go to Plaining Results: Individual lines screen.where you will get Plan order on which when double click you will get pop screen below,where you have Planned order no,quantity,plant,storage location,and version.
    Now here you can select the required version,and it will become firmed. This BOM will be used in the order now. Try it.

Maybe you are looking for