Mesh & Remote AP with WLC

Dears
I have 4 WLCs,3 are active and one is backup Controller with AIR-LAP1522HZ-E-K9
So mesh technology i need i-e- One Rap will be connected through ethernet and 5 MAPs will be through wireless with 100 meter radius and start topology.RAP will be in the middle and MAPs arround the RAP as per my understanding.
I saw a documentaion in which we have to use the mac filter option.But at the same time RAP will be act as MAP.What are the options like for RAP we will say you are RAP and MAP and for MAP we will just instruct that you are MAP only and have to communicate with RAP.
Is there any step by step documentation or any suggestion from forum?
Can any one suggest for Option43 and Option 60? and what if we define DHCP on WLC we need options or not ?
For Remote Failiver which parameters we have to consider
Second i have to use Air Magnet.can some one suggest from forum?
Advance Thanks to All

Hi there!
The first thing you need to do is put mac addresses of all the APs (RAP and MAPS) in the MAC filtering list of WLC (Using GUI is easier for this). Now you have to get ur APs registered to WLC first before you can declare them RAP or MAP (Default setting is MAP so u need to declare only RAP). There are many ways to get APs registered to the controller, I would share the following two:
1. Priming the APs:
connect ur primary controller to a switch and connect all the APs (RAPs and MAPs) to the same subnet (preferably the same switch). Once you have put all the MACs in WLC, the APs will join controller in few minutes. When an AP joins the controller, access it using the gui of the controller and put necessary information like controller IPs and gateway (if u intend to put ur RAP in a different subnet than WLC). Save the configuration and reboot the APs. repeat the procedure for all APs. now the APs are ready to be placed in the network.
2. Using DHCP option 43 and 60:
This procedure is an alternate to priming. Here u prepare ur DHCP server before you connect ur APs in the network. You have to define a few strings and go through some steps. (cisco website has a very good documents available for the details)
Answering ur question you cannot define these DHCP options on WLC. Reason is when the APs boots for the first time, it needs to find the controller and by default, it generates request to the DHCP server on the network (See AP booting sequence for details). When we configure DHCP option 43 and 60, we actually place the controller IP address in the DHCP messages for the APs to find WLC. so configuring DHCP 43 on WLC is just like calling someone on phone to get one's phone number (in short, it wont work)

Similar Messages

Register APs at remote site with WLCs at the core via Metro E.

All,
I have problem with register APs at the remote site with WLCs at the core.
All of my WLCs are on main site; and the majority of APs are on same subnet and same site with the WLCs. This works just fine.
However I have a remote site with connected to the core via metro E. And I am unable to make the APs at this site register to the controllers at the core.
On remote site APs and PCs are on subnet. And PCs are work just fine. I have the DHCP scope options 43 set for the ip address of the WLCs.
Metro E interfaces are on 192.168.0.0 /24.
Clients (PCs and APs) at remote are on 192.168.56.0 /24
I have the configuration on the Metro E and and remote site on the attachment.
Thank in advantage.

To get APs registered, make sure AP is getting an ip address and can ping WLC
Once this is verified, run the following debugs on WLC CLI and attach it to the thread:
- debug mac addr
- debug capwap OR lwapp events enable
- debug capwap OR lwapp errors enable
- debug pm pki enable
To stop debug
- debug disable-all
In case you have 'console' access to remote site AP, capture AP boot up and then run "debug ip udp" on AP CLI
To stop this debug
AP# undebug all

Client get connected occationally with WLC 5508

Hi ,
I have one strange problem on wireless connection.
I just upgraded several 1131 APs to LAP with 2 new Cisco 5508 controller deployed, and we found the clients sometime can get conneted to the 1131 AP, and connection well, sometimes cannot. during our test, one conecion is ok, next one cannot, the third one seems ok again and again.
And we also have 2 new 1140 APs, seems no such problem,
The version for controller is 6.0.196.0, and Client is Lenevo PC with XP.
Any suggestion? or some troubleshooting procedure I can follow?
Thanks!
Roy

Thanks!
Seems some problem with open authentication.
On the Client, it reported cannot get associated.
on the WLC, while I am debug client it reports:
*Jul 14 10:18:51.844: 00:1f:3c:c2:e9:71 Sending Assoc Response to station on BSSID c4:7d:4f:47:a5:c0 (status 12)
*Jul 14 10:18:51.889: 00:1f:3c:c2:e9:71 Ignoring 802.11 assoc request from mobile pending deletion
*Jul 14 10:18:51.889: 00:1f:3c:c2:e9:71 Sending Assoc Response to station on BSSID c4:7d:4f:47:a5:c0 (status 12)
*Jul 14 10:18:51.928: 00:1f:3c:c2:e9:71 Ignoring 802.11 assoc request from mobile pending deletion
*Jul 14 10:18:51.928: 00:1f:3c:c2:e9:71 Sending Assoc Response to station on BSSID c4:7d:4f:47:ae:b0 (status 12)
*Jul 14 10:18:52.446: 00:1f:3c:c2:e9:71 apfMsExpireCallback (apf_ms.c:418) Expiring Mobile!
*Jul 14 10:18:52.446: 00:1f:3c:c2:e9:71 apfMsExpireMobileStation (apf_ms.c:4427) Changing state for mobile 00:1f:3c:c2:e9:71 on AP c4:7d:4f:47:ae:b0 from Associated to Disassociated
I am using remote radius with WLC only.
The strange thing is, when get connected, it looks fine, but I tried disconnect manually, then connect again, it reported cannot get associated, then I try again, it can get connect again,....

1510 Mesh A.P with 5508 WLAN Controller

Hi everyone,
I got a situation. We had our wireless mesh network running with 4400 Controller and 1510 A.Ps. Now that we have bought new 5508 Controller (with SW: 7.2) and 3600 Indoor APs, we are unable to add legacy APs on our new controller. After a wild googling I have found that for 1510 APs i need to be on SW ver: 4.0. But that will lead into another situation i-e I wont be able to have my 3600 APs on WLAN Controller.
Any suggessions/wise words will be very very obliged....
Thanks,
Azhar...

You would have to keep those 440's up and have all the WLC in the same mobility group. That is the only way to keep those 1510's up and running. Cusco usually supports mobility between different version but only really as far back as 2 versions. Might work though.
Here is a compatibility guide that explains what devices work with what code.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
Sent from Cisco Technical Support iPhone App

Trunk with WLC and 1400BR problem

hi everybody,
i have the next proble, i hope someone can help me
Actually I wrok with a 1522 Mesh Network,1130 LWAPP and Bridge 1400 point to point. 1522 and 1130 are asociated with WLC.
I have a WLC4402 (4.1.192.22M (Mesh)image) this wlc is conected via trunk to Sw3750 ex:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport mode trunk
RAP1 is connected to the sameSw3750 ex:
interface FastEthernet1/0/23
description RAP1
switchport access vlan 10
**(VLAN 10 is Mgmt)**
AP1(1130) is connected to the same Sw3750 ex:
interface FastEthernet1/0/1
description AP1
switchport access vlan 10
The 1410BR Root is connected via trunk to same Sw3750 ex:
interface FastEthernet1/0/19
description BR-1400R
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport mode trunk
In the other point is the Non-Root connected to a Sw2960 ex:
interface GigabitEthernet1/0/1
switchport trunk native vlan 10
switchport mode trunk
AP2(1130) connected to the same Sw2960 ex:
interface fa0/23
descriptipon AP2
switchport access vlan 10
The network is work fine, Mesh UP (RAP and MAPs), and 1130 too.I connected the 1400 Bridge point after the Mesh is up, and the link between Root and Non Root is UP
Now, when the Sw3750 goes down or reboot,the RAP and AP1(1130) can't associated to WLC. The ports of RAP and 1130 are down and up many times, so can't associated to a WLC. Only the Bridge point 1400 Root and Non-root are UP, and the AP2(1130) in the other side can associated to the WLC.
When shutdown the port of the Root Bridge, Now the RAP1 and AP1(1130) can associated to the WLC and the Mesh Net is UP. Then no shutdown the Root Bridge port and the link between Bridges are UP, AP2(1130) up to the controller too.
But after several minutes the Bridge down, and the event log in the Root is:Interface Dot11Radio0 Radio transmit power out of range.
So i have this problems
1) Trunks between WLC and 1400 BR
2) Bridge conectivity range.
Regards
Antonio

The Outdoor Bridge Range Calculation Utility uses parameters that include regulatory domain, device type, data rate, antenna gain, and a few others as inputs.
You can avoid connectivity problems with the Outdoor Bridge Calculation Utility, as this tool helps you to predict the distance between devices. In a wireless environment without a tool like this, you cannot predict the distance between the bridges, the height at which you must place the antennas for maximum throughput, and other variables. This utility also helps you decide on the type of antenna that you must use in order to cover the distance between the bridges.

Unable to pair Apple Remote App with iTunes

I am running a Toshiba Satellite L505D-S5965 with Windows Vista SP 2. My iTunes software is 8.2.1.6, and my iPhone 3GS is running OS 3.0.1 (7A400). Both the Satellite and iPhone are connected to the same WiFi local network, and yet the App "Remote" by Apple Software is unable to communicate with iTunes to allow the entry of the four digit code to establish control of the iTunes library. Shortly after purchasing the iPhone 3GS I purchased the Satellite, but in the couple of weeks between the purchases the Remote App worked fine on my Gateway running Windows XP SP2. I have been through Apple Telephone support twice, and have really run one of the technicians through the mill researching possible solutions. I have visited an Apple Store Genius, who could find no reason for the problem. The iPhone and Remote App worked perfectly well on the store's WiFi and Mac, but his iPhone also wouldn't work with my laptop. I have been through Kaspersky's technical support system to ensure that there isn't a firewall issue. They have assured me, after reviewing logs from my laptop, that this is not the case. I even went so far as to uninstall all my Kaspersky product, but the Apple Remote App still would not function properly. I have updated the router's firmware, and checked that the laptop's wireless card is running the latest driver. At this point I can't think of anything else to try but would really appreciate any suggestions. Thanks, Steve

Monday 7th Jan.
Just to say that Apple did call me this am to discuss the problem on foot of a call I made last week.
In the meantime the remote worked with both a 2007 IMac and a 2009 laptop but not on the m-mini.
When I tried pairing this morning during the call by pressing Menu and next together it paired.
The change is very subtle, it just says paired in the advanced section of the security et sl section as referred before, with a fleeting 2 intersecting rings icon.
The big difference is that Front Row is gone....
The remote only works to a limited degree within some apps such as iTunes and iPhotos.
In theory it controls the volume in iTunes but as of now for me it doesnt....:( need to look more.
As to what the problem was:
It seems there is a set of keyboard combinations that can be used to force a reset the ID of the remote, the suggestion is MAYBE that by getting it to work on the iMac and laptop in some way reset the ID.
This stuff is WAY beyond my skill level:)
I did impress upon Apple the need to look at the issue in threads like this....
Message was edited by: qazxsw52

Remote app with Apple TV

I use the Remote app with both an iPad and iPhone to control my first gen Apple TV. This works fine except for one thing. When I select "Apple TV" as the library, using an iPhone I have access to all my library including Podcasts. When I run the same app on my Ipad, still selecting "Apple TV" as the library, no Podcasts come up on the iPad to select - the category is completely missing.
Has anyone else seen this issue ? Are they still there but hidden somewhere else ? Bear in mind I keep no content on the Apple TV - it is effectively just acting as a wireless device to get the signal to my TV.

Literally nothing happens. I click the done button and hear a beep. Over and over again.
On the phone, the passcode is still displayed.
Thank you for your help.

How does Remote work with Apple TV?

How does Remote work with Apple TV?
1. Does Remote, "Play" the music that resides on your iPod Touch>Apple TV>Home Speakers.
OR
Does Remote "Control" the music that resides on Apple TV HD>Home Speakers.
(If so... say you have a iPod Touch that only holds 8GB's but your music collection on your Apple TV exceeds that amount.
Will Remote still "Control" the larger music collection on Apple TV or your computer?)
2. Will iPod Wifi work on a patio outside a home to control Apple TV inside the home?
thank you in advance, Tom

Remote is a way to control iTunes on either your computer or Apple TV using a WiFi connection. See this article for complete instructions.

Why isn't my remote working with my Apple TV?

I have had my Apple TV a while now and I noticed a while back that the remote wasn't working with my TV. I assumed that I needed to replace the batteries so I downloaded the Remote app with my iPhone. Once I replaced the batteries, the remote still didn't work with my Apple TV. I reset my Apple TV to factory settings the other day because I noticed that my newer music that I had purchased recenlty wasn't showing in my music. Once I reset it, there was a screen that came up to set the TV up again but since I can't use the remoted I can't choose English as my language. In small writing at the bottom, it says I can use my iPhone or iPad as a remote by searching for my Apple TV in the bluetooth settings. When I try that on my iPhone and iPad neither of them show the TV as being able to pair with it. Has anyone else had a similar issue or can think of anything that I can do? I tried holding the Menu and left keys, I have held just about all the keys for more than 6 seconds and nothing ever happens. Thank you in advance for any suggestions.

You can use your IOS device to do initial setup on an Apple TV, but you won't be able to use it as a remote as that also requires home sharing to be enabled. I would take it to Apple to test the remote and/or get a replacement.

If I were to purchase the Apple Remote Desktop with Unlimited licenses, would I be able to install the client software on each of there computers/laptops and have them remote desktop into the server?

I have several friends and family who are looking for a central place to access information from ( Pictures, home movies etc ). So I am considering setting up an OSX Lion Server. There are some other things I can use it for as well.
Here is my question:
If I were to purchase the Apple Remote Desktop with Unlimited licenses, would I be able to install the client software on each of there computers/laptops and have them remote desktop into the server? Or would I have to install the Admin software on each? Do they intend it to be used strictly as one admin to access many clients?
I always could set up a network drive so they can log in and just see the folders they have created with space on the server I provide them. But I want them to be able to log an and actually use it as a Remote Desktop.
Thanks,
Eric

Dave,
Thanks for the feedback. I understand that ARD is meant for Remote Administration, but I was not sure if it could be used for my purpose as well. The reason I was looking to do it this was was because I read several articles online about security and performance issues with setting up VNC and activating screen sharing. Unless I am misunderstood.
As far as people's activities on the server, mostly it is going to be used as a place for them to store their media. I will only allow own person ( Who I trust and I know wont botch the server ), to run applications. Everyone else will be restricted to uploading and downloading content to their designated account on the server as well as a community share on the server.
I appreciate your help.
Thanks,
Eric

How can you run a command with elevated rights on a remote server with invoke-command ?

I am trying to run a script on a remote server with invoke-command. The script is starting and is running fine, but the problem is that it should be running with elevated rights on the remote server. On the server where I start the invoke-command, my account has the necessary rights.
The server were I launch the invoke-command is a W2K8 R2. The remote box is a W2K3 with powershell v2.0 installed.
When I launch the script on the remote-box from the command line, I don't get the access denied's.
Is there a way to do this ?
Thanks in advance

The script that I want to run is to install the windows updates. I get an access denied on the download of the updates.
When I execute the script on an W2K8 box, (not remotely) and I run it with non-elevated rights, I get the same error.
The script is running fine when it is launched on W2K3 box locally with a domain account that has local admin rights, or on a W2K8 R2 server with a domain account that has local admin rights, but with elevated rights.
Thanks in advance for your help.
#=== start script ====
param($installOption="TESTINSTALL",$rebootOption="NOREBOOT")
Function Show-Help
Write-Host ""
Write-Host "SCRIPT: $scriptName <installOption> <RebootOption>"
Write-Host ""
Write-Host "DESCRIPTION: Installatie van WSUS updates op de lokale server"
Write-Host ""
Write-Host "PARAMETERS"
Write-Host " -installOption <[INSTALL|TESTINSTALL]>"
Write-Host " -rebootOption <[REBOOT|NOREBOOT|REBOOT_IF_UPDATED]>"
Write-Host ""
Write-Host "EXAMPLE:"
Write-Host "$ScriptName -installOption INSTALL -rebootOption REBOOT_IF_UPDATED"
Write-Host "$ScriptNAme INSTALL NOREBOOT"
Write-Host ""
Write-Host "Indien beide parameter weggelaten worden zijn de defaultwaarden :"
Write-Host " installOption=TESTINSTALL "
Write-Host " RebootOption=NOREBOOT"
Write-Host ""
Exit
#Include alle globale variablen
$CEIF_WIN_PATH = (get-content env:CEIF_WIN_PATH)
$includeFile=$CEIF_WIN_PATH + "\Scripts\include_win.ps1"
. $includeFile
#initialiseer error count
$errcnt=0
$scriptName=$MyInvocation.MyCommand.Name
#argumenten controleren
$arrInstallOption= "TESTINSTALL", "INSTALL" # Mandatory variable with predefined values
If (!($arrInstallOption –contains $installOption)){ Show-Help }
$arrRebootOption = "REBOOT", "NOREBOOT","REBOOT_IF_UPDATED" # Mandatory variable with predefined values
If (!($arrRebootOption –contains $rebootOption)){ Show-Help }
#Logfile opbouwen
$logfile = get-logfileName($MyInvocation.MyCommand.Name)
Log-scriptStart $MyInvocation.MyCommand.Name $logfile
function Get-WIAStatusValue($value)
switch -exact ($value)
0 {"NotStarted"}
1 {"InProgress"}
2 {"Succeeded"}
3 {"SucceededWithErrors"}
4 {"Failed"}
5 {"Aborted"}
function boot-server()
if ($installOption -eq "TESTINSTALL")
logger "TESTINSTALL : - Reboot local Server" $logfile
else
logger " - Reboot local Server" $logfile
$thisServer = gwmi win32_operatingsystem
$thisServer.psbase.Scope.Options.EnablePrivileges = $true
$thisServer.Reboot()
$logmsg="Install option = " + $installOption + ", RebootOption = $rebootOption"
logger "$logmsg" $logfile
logger "" $logfile
logger " - Creating WU COM object" $logfile
$UpdateSession = New-Object -ComObject Microsoft.Update.Session
$UpdateSearcher = $UpdateSession.CreateUpdateSearcher()
logger " - Searching for Updates" $logfile
$SearchResult = $UpdateSearcher.Search("IsAssigned=1 and IsHidden=0 and IsInstalled=0")
logger " - Found [$($SearchResult.Updates.count)] Updates to Download and install" $logfile
$Updates=$($SearchResult.Updates.count)
logger "" $logfile
foreach($Update in $SearchResult.Updates)
if ($Update.EulaAccepted -eq 0)
$Update.AcceptEula()
# Add Update to Collection
$UpdatesCollection = New-Object -ComObject Microsoft.Update.UpdateColl
$UpdatesCollection.Add($Update) | out-null
if ($installOption -eq "TESTINSTALL")
else
# Download
logger " + Downloading Update $($Update.Title)" $logfile
$UpdatesDownloader = $UpdateSession.CreateUpdateDownloader()
$UpdatesDownloader.Updates = $UpdatesCollection
$DownloadResult = $UpdatesDownloader.Download()
$Message = " - Download {0}" -f (Get-WIAStatusValue $DownloadResult.ResultCode)
if ($DownloadResult.ResultCode -eq 4 )
{ $errcnt = 1 }
logger $message $logfile
# Install
logger " - Installing Update" $logfile
$UpdatesInstaller = $UpdateSession.CreateUpdateInstaller()
$UpdatesInstaller.Updates = $UpdatesCollection
$InstallResult = $UpdatesInstaller.Install()
$Message = " - Install {0}" -f (Get-WIAStatusValue $InstallResult.ResultCode)
if ($InstallResult.ResultCode -eq 4 )
{ $errcnt = 1 }
logger $message $logfile
logger "" $logfile
#Indien er een fout gebeurde tijdens download/installatie -> stuur mail naar windowsteam
if ( $errcnt -gt 0 )
logger " - Fout tijdens de uitvoering van script -> send mail" $logfile
$mailSubject=$MyInvocation.MyCommand.Name
$msg = new-object Net.Mail.MailMessage
$att = new-object Net.Mail.Attachment($logfile)
$smtp = new-object Net.Mail.SmtpClient($smtpServer)
$msg.From = $mailFrom
$msg.To.Add($mailTo)
$msg.Subject = $mailSubject
$msg.Body = “Meer details in attachement”
$msg.Attachments.Add($att)
$smtp.Send($msg)
#Moet de server herstart worden ?
if ($rebootOption -eq "REBOOT_IF_UPDATED" )
if ($Updates -gt 0)
#Reboot the server when updates are installed
boot-server
elseif ($rebootOption -eq "REBOOT")
#reboot the server always
boot-server
else
#Do not reboot the server
logger "Do not reboot the server" $logfile
Log-scriptEnd $MyInvocation.MyCommand.Name $logfile
exit 0

Remote Site with its own CUCM Sub#2 and Router network failed and the site didnt keep its phones active, need some assistance

I have a Pub and 2 Sub's. Sub #1 is with the Pub, at the main site it is our TFTP server, Sub #2 is at a remote site with about 100 users along with a router and 2 PRI's for outbound calls. We had a network failure between the main site and the remote site and all phone lost their registration with the system until we were able to get the network back up. Currently the network is up in a crippled state on a 1 T-1 link while we troubleshoot the bigger issue with our 6mb pipe, however Sub #2 and its associated router arent talking with the PUB or other Sub. I'm still getting alerts every 30 minutes stating they are the server is down. I'm sure once the network is corrected this will bring everything back on line. My question is how can I prevent in this in the future. I need this site to be stand alone if the network goes down again. I was told by our vendor that if we had a subscriber at each site then we would need SRST licensing. I know something needs to be configured to make it all work, I'm just not sure what.

I already have a group at the site but it includes both the Pub and Sub from the main site as well as the Sub from the remote site. I would only have to remove the Sub from the main site, problem is I currently only have 1 TFTP server it runs on SUB #1, should I make SUB#2 a TFTP server as well and the phones are setup for DHCP at the main site, I'm going to need to have a DHCP server setup at the remote site as well. Correct?

It´s possible to use the "Remote" app with Itunes and a Nokia E72 with Joikuspot installed only? Or I´ll need to buy a modem Wifi?

It´s possible to use the "Remote" app with Itunes and a Nokia E72 with Joikuspot installed only? Or I´ll need to buy a modem Wifi?
I was using "remote" with a D-link modem, that works fine at my iPad. But now I´m using only the cell phone as modem 3G, and don´t want to intall a router to put new cables at my notebook.

What?
You want to control iTunes on your computer using the Remote app on your iPad?
And you want to connect the iPad and computer through your Nokia?
No, this will not work.
Just create a network with your notebook.

Unable to syndicate same Remote System with differnt value

Hi,
I am working on MDM 7.1 SP05 and I have the following issue with syndication:
I have a remote system table (Key Enabled) with System as Non-Qualifier and value as Qualifier and I have values in the MDM Datamanager as
MDM ID, Remotesystem (Multivalue Qualifier Table with Key Enabled)
111,((Qual1-Key,Val1),(Qual1-Key,Val2),(Qual1-Key,Val3))
When I syndicate I see only one value as 111, (Qual1,Val3)... But I want to have all the Qualifiers-Key with multiple values.. Where as in MDM 5.5 I can see all the Qualifiers with out any issues..Is this a restriction in MDM 7.1?
If I map System instead of Remote Key of Qualifier Table then I can see multiple times of same remote system with appropriate values.. But If I map remote key then I see the consolidated/the latest system-remote key wiht value... But I want system-remote key value appear multiple times...
Thanks alot
Rajeev

I am using customised...
Did you tried syndicating Remote key of that table or the field of the Qualifer table?
I am able to syndicate out with the system field and values.. But I want to syndicate out the multiple values wiht remote key of the table..
As mentioned Remote keys are AAA and BBB for System Sys1 and Sys2..
First I imported remote system table with Sys1 and Sys2 with remote Keys as AAA and BBB. then along wiht main table record I imported Sys1 and Sy2...
While Syndicating I want to syndicate AAA and BBB values along with Value field...
Suppose:
I have data :
MDM ID, RemoteSystem(System, Value)
111, ((Sys1,Val1),(Sys1,Val2),(Sys1,Val3),(Sys2,Val1))
Remote Keys for Sys1AAA and Sys2BBB
In the Syndication Manager I mapped as below: RemoteSystems RemoteKey and value are mapped to target...
RemoteSystem
--RemoteKey
System(DFNQ)
--Value(Qualifier)
I mapped RemoteKey and Value to the target fields.. Which is a XML output..
<REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val3</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>BBB</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val1</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
</REMOTE_SYSTEM>
Where I need the following Output:
<REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val1</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val2</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val3</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>BBB</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val1</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
</REMOTE_SYSTEM>
Any inputs.
Thanks
Rajeev

DOES THE APPLE REMOTE WORK WITH THE IPOD TOUCH..? WITHOUT A DOCK..

HI
DOES THE APPLE REMOTE WORK WITH THE IPOD TOUCH 5TH GEN..? WHITHOUT A DOCK..??
THANKS ANYONE

This Apple remote requires a dock since this remote uses IR and the iPod does not ha IR capibility,.
Manufacturer Information
Apple Remote with iPod and iPhone: Please note a Universal Dock is required in order to use the Apple Remote with your iPhone or iPod.
http://store.apple.com/us/product/MC377LL/A/apple-remote?

Mesh & Remote AP with WLC

Similar Messages

Maybe you are looking for