Metro-E circuits between two sites
We have two sites connected by two equal cost Metro Ethernet circuits from two different service providers. we also have two redundant L3 core switches at both sites. What is the best way to connect these two sites for load balancing as well as redundancy? They are on different subnets. The core switches currently run HSRP. We also evaluating GLBP as a possible alternative.We want to possibly avoid all single points of failure.
You could, as you note, use GLBP, but an alternative could be, make the two paths from the intial/primary HSRP gateway appear equal cost. Many routing protocols would then alternate flows across the two paths.
Similar Messages
-
Exchange High availability between two sites with two servers
Hi Team,
I have a requirement to deploy exchange server 2010 between two sites. but i have limited resources to full fill this. below the summary.
2 servers in two sites
different subnets will user for two sites
Need to deploy DAG.
please let me know the considerations for this deployment.
Thank youHi - In this scenario, you would setup the following: Site 1: Exchange 2010 Multi-Role server File Share location to place File Share Witness for the DAG Site 2: Exchange 2010 Multi-Role server The above will give you 2 nodes in the primary location and
one node in the secondary location so that resources will stay in Site one. You will also need to enable DAC (Datacenter Activation Coordination) on the DAG so that the Cluster group can be managed by Exchange. Last but not least, you will want to restrict
automatic failover of resources to Site 2 by blocking that action on the Exchange server in Site 2 using 'Set-MailboxServer <servername> -DatabaseCopyAutoActivationPolicy Blocked' This will make you manually failover to site 2 and not end up with resources
there after a sudden failure or issue that is not impacting the entire site.Jason Apt Microsoft Certified Master | Exchange 2010 -
Mapi connection behaviour between two sites-Exchange 2010
Hello,
I have small doubt, need help from you guys,
i have two sites A, B, DAG is span over the two sites;
Both site has array Of different FQDN
site A has active copies, its PASSIVE copies are in site-B
i have witnesserver in third location
if Active mailbox database in Site-A fails, passive copy on Site-B will become active; i guess
My question is ===> without downtime or without MANUAL Task, will mapi connection goes to site-B copy ??? ,Hi,
In Cross Site maintainence we, have to work out mainly on Database Activation Coordination Mode(DAC) which avoids the split brain syndrome.
below URL's gives you clear vision on how we can do that and what it is for.
- http://www.msexchange.org/articles-tutorials/exchange-server-2010/management-administration/planning-deploying-testing-exchange-2010-site-resilient-solution-sized-medium-organization-part7.html
- https://technet.microsoft.com/en-us/library/dd979790.aspx
Regards,
Gowtham T -
Redundant stateful CSS11501 between two sites
We have layer 2 connectivity between to core sites and are implementing two new CSS11501's. Is it possable to implement these in a active/backup configuration and stateful?
not statefullness.
To be statefull your setup needs a dedicated link between the 2 CSS - no extra hop or L2 switch.
You can give it a try but this is not a supported setup.
For active/backup this is no problem.
Regards,
Gilles. -
Repository synchronization between two sites
Hi All,
We are using Oracle Designer 6i for our designs. We are creating DFDs, PFDs and ERDs. Two teams are working on this at two different locations. Can somebody suggest the way to synchronize (combine) the work done by both the teams into a single repository. For example, Team A has created DFDs, PFDs and ERDs at Location1. Team B is also creating DFDs, PFDs and ERDs at Location2. Team B will be using some of the functions in their diagrams created by Team A. Now we want to apply the changes done by Team B into the repository located at Location1.
Thanks in advance for any suggestions
regards,
VijayHi Vishal,
thanks a lot for your reply. You have suggested that we can import the entire application system at Site B. At this time we are using non-versioned repository. And we are using only one application system. But the problem is that at Site B some people are making changes to the same application system used at Site A. I understand that if i have to import an application system, i have to make sure that there is no application system with the same name at the destination. So in this case if i have to import the Site A's application system at Site B, first i have to delete the Site B application system. In which case i will be losing all the changes made by the Team at Site B. But my requirement is that i want to incorporate the chages made at Site B's application system into the Site A's application system. Can you please give your thoughts about this.
thanks in advance
regards,
Vijay -
Setup AD Domain Between Two Sites
I am starting to learn Active Directory on Windows server. Currently I have downloaded Windows Server 2012 R2 eval. Using basic home internet connection at my house and neighbours (who agreed to help me with my studying) we each have your basic home WiFi
routers. Would like to test out setting up a domain in which a DC is at my house, and one at his house and be able to replicate the directory between the two DC's.
I am really lost on how to go about configuring the routers and respective DNS servers for this to work properly. Anybody know of a basic guide to get me started?1. First of all for simple transfer you need to open ports that AD uses
http://technet.microsoft.com/en-us/library/dd772723(v=ws.10).aspx
2. AD uses DNS that is integrated (in majority of cases) and use of public DNS is unwanted. Similar situation is with DHCP. On the other way, router assignes IP and resolve FQDN.
3. Some configurations with WiFi cards are not allowed in WS2012, for example teaming.
4. Using WiFi is unexpected in AD. That is why I would use least problematic locan network configuration or virtual one.
5. I recommend some reading about AD, Technet guides and step-by-step guides as well as books that ain AD basics.
Regards
Milos -
Site to Site VPN Between Two ASA 5505's Up But Not Passing Traffic
hello,
i am setting up a site to site vpn between two asa 5505's. the tunnel is up but i cannot get it to pass traffic and i have run out of ideas at this point. i am on site as i am posting this question and only have about 4 hours left to figure this out, so any help asap is greatly appreciated. i'll post the configs below along with the output of sh crypto isakmp sa and sh ipsec sa.
FYI the asa's are different versions, one is 9.2 the other is 8.2
Note: 1.1.1.1 = public ip for Site A 2.2.2.2 = public ip for site B
Site A running config:
Result of the command: "sh run"
: Saved
ASA Version 8.2(2)
hostname csol-asa
enable password WI19w3dXj6ANP8c6 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.1.0 san_antonio_inside
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 1.1.1.1 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
name-server 24.93.41.125
name-server 24.93.41.126
object-group network NETWORK_OBJ_192.168.2.0_24
access-list inside_access_out extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list outside_access_in extended permit icmp any any
access-list outside_access_in_1 extended permit icmp any interface outside
access-list outside_access_in_1 extended permit tcp any interface outside eq pop3
access-list outside_access_in_1 extended permit tcp any interface outside eq 8100
access-list outside_access_in_1 extended permit udp any interface outside eq 8100
access-list outside_access_in_1 extended permit udp any interface outside eq 1025
access-list outside_access_in_1 extended permit tcp any interface outside eq 1025
access-list outside_access_in_1 extended permit tcp any interface outside eq 5020
access-list outside_access_in_1 extended permit tcp any interface outside eq 8080
access-list outside_access_in_1 extended permit tcp any interface outside eq www
access-list outside_access_in_1 extended permit ip san_antonio_inside 255.255.255.0 any
access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 host san_antonio_inside
access-list outside_1_cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 san_antonio_inside 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 san_antonio_inside 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (inside) 2 interface
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface pop3 192.168.2.249 pop3 netmask 255.255.255.255
static (inside,outside) tcp interface 8100 192.168.2.161 8100 netmask 255.255.255.255
static (inside,outside) udp interface 8100 192.168.2.161 8100 netmask 255.255.255.255
static (inside,outside) udp interface 1025 192.168.2.161 1025 netmask 255.255.255.255
static (inside,outside) tcp interface 5020 192.168.2.8 5020 netmask 255.255.255.255
static (inside,outside) tcp interface 8080 192.168.2.251 8080 netmask 255.255.255.255
static (inside,inside) tcp interface www 192.168.2.8 www netmask 255.255.255.255
static (inside,outside) tcp interface 1025 192.168.2.161 1025 netmask 255.255.255.255
access-group inside_access_out out interface inside
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 1.1.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.2.0 255.255.255.0 inside
http 2.2.2.2 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map1 1 match address outside_1_cryptomap_1
crypto map outside_map1 1 set peer 2.2.2.2
crypto map outside_map1 1 set transform-set ESP-3DES-SHA
crypto map outside_map1 interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.30-192.168.2.155 inside
dhcpd dns 24.93.41.125 24.93.41.126 interface inside
dhcpd domain corporatesolutionsfw.local interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
group-policy DfltGrpPolicy attributes
tunnel-group 2.2.2.2 type ipsec-l2l
tunnel-group 2.2.2.2 ipsec-attributes
pre-shared-key *****
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:021cf43a4211a99232849372c380dda2
: end
Site A sh crypto isakmp sa:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 2.2.2.2
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Site A sh ipsec sa:
Result of the command: "sh ipsec sa"
interface: outside
Crypto map tag: outside_map1, seq num: 1, local addr: 1.1.1.1
access-list outside_1_cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (san_antonio_inside/255.255.255.0/0/0)
current_peer: 2.2.2.2
#pkts encaps: 1, #pkts encrypt: 1, #pkts digest: 1
#pkts decaps: 239, #pkts decrypt: 239, #pkts verify: 239
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 1, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 1.1.1.1, remote crypto endpt.: 71.40.110.179
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: C1074C40
current inbound spi : B21273A9
inbound esp sas:
spi: 0xB21273A9 (2987553705)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 1691648, crypto-map: outside_map1
sa timing: remaining key lifetime (kB/sec): (3914989/27694)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xC1074C40 (3238480960)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 1691648, crypto-map: outside_map1
sa timing: remaining key lifetime (kB/sec): (3914999/27694)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Site B running config:
Result of the command: "sh run"
: Saved
: Serial Number: JMX184640WY
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)4
hostname CSOLSAASA
enable password WI19w3dXj6ANP8c6 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
ftp mode passive
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network mcallen_network
subnet 192.168.2.0 255.255.255.0
access-list outside_cryptomap extended permit ip object NETWORK_OBJ_192.168.1.0_24 object mcallen_network
access-list outside_access_in extended permit ip object mcallen_network 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static mcallen_network mcallen_network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 2.2.2.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map3 1 match address outside_cryptomap
crypto map outside_map3 1 set peer 1.1.1.1
crypto map outside_map3 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map3 interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd address 192.168.1.200-192.168.1.250 inside
dhcpd dns 24.93.41.125 24.93.41.126 interface inside
dhcpd domain CSOLSA.LOCAL interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
ikev1 pre-shared-key *****
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4e058021a6e84ac7956dca0e5a143b8d
: end
Site B sh crypto isakmp sa:
Result of the command: "sh crypto isakmp sa"
IKEv1 SAs:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 1.1.1.1
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
There are no IKEv2 SAs
Site B sh ipsec sa:
Result of the command: "sh ipsec sa"
interface: outside
Crypto map tag: outside_map3, seq num: 1, local addr: 71.40.110.179
access-list outside_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
current_peer: 1.1.1.1
#pkts encaps: 286, #pkts encrypt: 286, #pkts digest: 286
#pkts decaps: 1, #pkts decrypt: 1, #pkts verify: 1
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 286, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 2.2.2.2/0, remote crypto endpt.: 1.1.1.1/0
path mtu 1500, ipsec overhead 58(36), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: B21273A9
current inbound spi : C1074C40
inbound esp sas:
spi: 0xC1074C40 (3238480960)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 28672, crypto-map: outside_map3
sa timing: remaining key lifetime (kB/sec): (4373999/27456)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000003
outbound esp sas:
spi: 0xB21273A9 (2987553705)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 28672, crypto-map: outside_map3
sa timing: remaining key lifetime (kB/sec): (4373987/27456)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001Hi Keegan,
Your tunnel is up and encrypting traffic one way, the other end is not able to encrypt the traffic.
I would suggest to do a 'clear xlate'? Sometimes if you setup the nonat configuration after you've attempted other configurations, you need to 'clear xlate' before the previous NAT configuration is cleared and the new one works.
HTH
"Please rate useful posts" -
Hi All,
Please have a look in to the below mentioned environment.
primary site :SITE 1
server 1
server 2
secondary site :SITE 2
server 3
Note : All the above three servers are in single DAG .All the database are mounted on the server (server 1) which is located in the primary site (I.E SITE 1).
On that 5 databases we are having 3500 users .Based on the user designation we have allocated the mailbox size.
Query : Each and every day we are having the large no copy queue length for all the five databases to the server located in SITE 2.
Please help me out on this and also tell me is there any tool available to exactly get the required bandwidth for the exchange servers located between the active directory sites.
Thanks & Regards S.NithyanandhamI don't know of any tool that can calculate things for you but latency is the biggest thing you have to worry about. The other issues is looking at the network gear between the 2 sites. I have seen many times were switches get maxed out if they are set to
1 GB or even ports getting maxed out and need to bonded for more throughput. Test your latency from the edge of each site then test it within to see if there is a difference.
Regardless of their geographic location relative to other DAG members, each member of the DAG must have round trip network latency no greater than 500 milliseconds between each other member.
As the round trip latency between two Mailbox servers hosting copies of a database increases, the potential for replication not being up to date also increases. Regardless of the latency of the solution, customers should validate that the networks between
all DAG members is capable of satisfying the data protection and availability goals of the deployment. Configurations with higher latency values may require special tuning of DAG, replication, and network parameters, such as increasing the number of databases
or decreasing the number of mailboxes per database, to achieve the desired goals.
Round trip latency requirements may not be the most stringent network bandwidth and latency requirement for a multi-datacenter configuration. You must evaluate the total network load, which
includes client access, Active Directory, transport, continuous replication, and other application traffic, to determine the necessary network requirements for your environment.
http://technet.microsoft.com/en-us/library/dd638104(v=exchg.150).aspx
DJ Grijalva | MCITP: EMA 2007/2010 SPA 2010 | www.persistentcerebro.com -
What is the difference between these two sites.
What is the difference between (this site) Apple Support Communities and the Developer forum.
When I search on "apple developers forum" what is the difference between the first and the seconde hit.
RL6001RL6001 wrote:
What is the difference between (this site) Apple Support Communities and the Developer forum.
Aside from any other benefits of the paid developer programs, the Developer forums are focused solely on developers. This forums is just one little out-of-the-way corner of a much larger, more consumer oriented discussion site. Questions asked in the Developer forums are typically more difficult and may take several days to get an answer. Questions here are more beginner-type questions and you will get an answer much more quickly. The Developer forums are mostly populated by professional developers who have a much different perspective than you get on most other public internet forums. If you don't know what I'm talking about then you probably wouldn't believe me anyway. -
Unable to find line break between two lines in attachment file.
Dear all I will be very great full if someone help me out,
I am trying to send mail through SMTP server with an attachment of oracle report, but I am unable to find line break between two lines, when I down load the attachment from mail and open attach.txt file by double click on it. Next line starts right after previous line ends, it should starts with new line.
In order to send an attachment file, I am reading source file line by line and put MIME protocol’s attachment instance, contain of source file is being properly written into target file if I open that attachment on cmd prompt.
Following code may help you to understand the case.
Thanks in advance.
My code is as follows:-
create or replace procedure bec_file_test
v_subject varchar2, -- Subject of the email
v_body varchar2, -- Body of the email
v_from VARCHAR2 default 'XYZ.com', -- sender mail id
v_to varchar2 default 'XYZ.com', -- Field To of the email
v_cc varchar2 default 'XYZ.com' -- cc address
) is
-- variable to hold the smtp server connection
v_smtp_connection utl_smtp.connection;
-- variable to hold the smtp host name
v_smtp_host varchar2(100) default 'mail.bec-group.com';
-- variable to hold the smtp port
v_smtp_port number default 25;
-- composite of {CR}{LF} caridge return and line feed.
CRLF varchar2(2):=CHR(13)||CHR(10);
cursor pr_rec is
select requisition_no,line_no,release_no,a.contract,
a.project_id,substr(a.activity_seq,1,11)ACT_SEQ,
substr(a.part_no,1,12)PART_NO,
substr(a.description,1,32)DESCRIPTION,
substr(a.Bal_qty,1,8) BAL_QTY,
substr(a.unit_meas,1,5)UOM,
a.wanted_receipt_date WAN_REC_DT,
a.latest_order_date LAT_ORD_DT
from bec_pr_line_rep a
where a.Bal_qty>0 and a.header_state not in 'Closed'
and upper(a.state1) like 'RELEASED' and a.contract not in ('U1ENG','ULENG','U1FND','U2FND')
and a.buyer_code='70306'
order by a.part_no;
begin
declare
fHandle UTL_FILE.FILE_TYPE;
v_msg_line varchar2(2000);
-- v_buffer varchar2(20000);
--ALTER SYSTEM SET utl_file_dir = 'D:\Database\temp'
--COMMENT='Temporary change on Dec 14'
--SCOPE=SPFILE;
SELECT name, value
FROM gv$parameter
WHERE name = 'utl_file_dir';
--drop directory my_directory
--CREATE or replace DIRECTORY my_directory AS 'D:\database\temp';
--GRANT read,write ON DIRECTORY my_directory TO PUBLIC;
begin ---writing data into a file.
fHandle := UTL_FILE.FOPEN('MY_DIRECTORY', 'pending_pr_summry.txt', 'w');
UTL_FILE.put_line(fHandle, ' Pending PR to process (detail report)');
UTL_FILE.put_line(fHandle,TO_CHAR(SYSDATE,'MM-DD-YY HH:MI:SS AM'));
UTL_FILE.put_line(fHandle, '--------------------------------------------------------------------------------------------------------------------------------------------------');
UTL_FILE.put_line(fHandle, 'Req.no. li Re Site Prj Id Act seq Part no Description Qty UOM want rec dt lat ord dt' );
UTL_FILE.put_line(fHandle, '--------------------------------------------------------------------------------------------------------------------------------------------------');
for pr_temp in pr_rec loop
begin
v_msg_line:=to_char(rpad(pr_temp.requisition_no,12,' ')||'|'||
lpad(pr_temp.line_no,3,' ')||'|'||
lpad(pr_temp.release_no,3,' ')||'|'||
rpad(pr_temp.contract,7,' ')||'|'||
lpad(nvl(pr_temp.project_id,' '),7,' ')||'|'||
lpad(nvl(pr_temp.act_seq,' '),12,' ')||'|'||
lpad(pr_temp.part_no,12,' ')||'|'||
rpad(pr_temp.description,35,' ')||'|'||
lpad(pr_temp.bal_qty,10,' ')||'|'||
rpad(pr_temp.uom,6,' ')||'|'||
lpad(pr_temp.wan_rec_dt,14,' ')||'|'||
lpad(pr_temp.lat_ord_dt,14,' '));
UTL_FILE.put_line(fHandle,v_msg_line);
end;
end loop;
UTL_FILE.put_line(fHandle, '--------------------------------------------------------------------------------------------------------------------------------------------------');
UTL_FILE.put_line(fHandle, ' Regards : IFSAPP ( Application owner ) ');
UTL_FILE.FCLOSE(fHandle); ------------writing into file is successfuly done here!
--Reading of file starts here containt will be added in attchment file
fHandle :=UTL_FILE.FOPEN('MY_DIRECTORY','pending_pr_summry.txt','R' );
-- establish the connection to the smtp server
v_smtp_connection := utl_smtp.open_connection(v_smtp_host, v_smtp_port); /** OPEN CONNECTION ON THE SERVER **/
-- perform a handshake with the smtp server
utl_smtp.helo(v_smtp_connection, v_smtp_host); /** DO THE INITIAL HAND SHAKE **/
-- set the 'from' address of the message
utl_smtp.mail(v_smtp_connection, v_from);
-- add the recipient to the message
utl_smtp.rcpt(v_smtp_connection, v_to);
-- send the email
utl_smtp.open_data(v_smtp_connection);
v_msg_line:='Date: ' || TO_CHAR( SYSDATE, 'dd Mon yy hh24:mi:ss' ) || CRLF ||
'From: ' || v_from || CRLF ||
'Subject: ' || v_subject || CRLF ||
'To: ' || v_to || CRLF ||
'Cc: ' || v_cc || CRLF ||
'MIME-Version: 1.0'|| CRLF || -- Use MIME mail standard
'Content-Type: multipart/mixed;'||CRLF ||
' boundary="-----SECBOUND"'||CRLF||
CRLF ||'-------SECBOUND'|| CRLF ||
'Content-Type: text/plain;'|| CRLF ||
'Content-Transfer_Encoding: 7bit'|| CRLF ||
CRLF ||v_body|| CRLF; -- Message body
utl_smtp.write_data(v_smtp_connection,v_msg_line);
v_msg_line:='-------SECBOUND'|| CRLF ||
'Content-Type: application/octet-stream;'|| CRLF ||
'Content-Type: text/plain;'|| CRLF ||
'name="pending_pr_summry.txt"'|| CRLF ||
'Content-Transfer_Encoding: 8bit'|| CRLF ||
'Content-Disposition: attachment;'|| CRLF ||
' filename="pending_pr_summry.txt"'|| CRLF || CRLF; -- Content of attachment
utl_smtp.write_data(v_smtp_connection,v_msg_line);
-- check file is opened
IF utl_file.is_open(fHandle) THEN
-- loop lines in the file
LOOP
BEGIN -- Content of attachment
utl_file.get_line(fHandle,v_msg_line);
v_msg_line:=concat(v_msg_line,CRLF);
utl_smtp.write_data(v_smtp_connection,v_msg_line);
EXCEPTION
WHEN NO_DATA_FOUND THEN
EXIT;
END;
END LOOP;
END IF;
--end of attachment containt
utl_smtp.write_data(v_smtp_connection,v_msg_line);
UTL_FILE.FCLOSE(fHandle);
utl_smtp.close_data(v_smtp_connection);
utl_smtp.quit(v_smtp_connection);
exception
when utl_smtp.invalid_operation then
dbms_output.put_line(' Invalid Operation in Mail attempt using UTL_SMTP.');
when utl_smtp.transient_error then
dbms_output.put_line(' Temporary e-mail issue - try again');
when utl_smtp.permanent_error then
dbms_output.put_line(' Permanent Error Encountered.');
when others then
dbms_output.put_line('Exception: SQLCODE=' || SQLCODE || ' SQLERRM=' || SQLERRM);
RAISE;
end;
end bec_file_test;Pending PR to process (detail report)01-17-13 12:43:19 PM--------------------------------------------------------------------------------------------------------------------------------------------------Req.no. li Re Site Prj Id Act seq Part no Description Qty UOM want rec dt lat ord dt--------------------------------------------------------------------------------------------------------------------------------------------------MAT/250370 | 2| 1|ISCSP | 4977| 100004207| 0104000016|Angle 50 X 50 X 6 IS:2062 Grade |500|kg |30-NOV-2012| 20-nov-2012MAT/250370 | 3| 1|ISCSP | 4977| 100004207| 0105000002|Channel 100 X 50 IS:2062 Grade A | 1000|kg | 30-NOV-2012| 20-nov-2012MAT/250579 | 2| 1|NMDCJ | 6001| 100005580| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 2991|kg | 13-DEC-2012| 03-dec-2012MAT/250606 | 2| |NMDCJ | 6002| 100005860| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 4500|kg | 29-DEC-2012| 19-dec-2012MAT/250607 | |1|NMDCJ|6001|100005580| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 1500|kg | 29-DEC-2012| 19-dec-2012MAT/250194 | 3| 1|NMDCJ | 6002| 100005818| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 3939|kg | 29-DEC-2012| 19-dec-2012MAT/250606 | 4| 1|NMDCJ | 6002| 100005860| 0109020004|TMT Bar 16 mm Fe 415 IS:1786 | 39000|kg | 29-DEC-2012| 19-dec-2012MAT/250607 | 4| 1|NMDCJ | 6001| 100005580| 0109020004|TMT Bar 16 mm Fe 415 IS:1786 | 17500|kg | 29-DEC-2012| 19-dec-2012MAT/250194 | 2| 1|NMDCJ | 6002| 100005818| 0109020004|TMT Bar 16 mm Fe 415 IS:1786 | 12183|kg | 29-DEC-2012| 19-dec-2012MAT/250606 | 6| 1|NMDCJ | 6002| 100005860| 0109020006|TMT Bar 25 mm Fe 415 IS:1786 | 9500|kg | 29-DEC-2012| 19-dec-2012MAT/250607 | 6| 1|NMDCJ | 6001| 100005580| 0109020006|TMT Bar 25 mm Fe 415 IS:1786 | 4500|kg | 29-DEC-2012| 19-dec-2012MAT/250194 | 6| 1|NMDCJ | 6002| 100005818| 0109020006|TMT Bar 25 mm Fe 415 IS:1786 | 17500|kg | 29-DEC-2012| 19-dec-2012MAT/250607 | 7| 1|NMDCJ | 6001| 100005580| 0109020008|TMT Bar 32 mm Fe 415 IS:1786 | 22000|kg | 29-DEC-2012| 19-dec-2012MAT/250194 | 7| 1|NMDCJ | 6002| 100005818| 0109020008|TMT Bar 32 mm Fe 415 IS:1786 | 27060|kg | 29-DEC-2012| 19-dec-2012MAT/251138 | 1| 1|NMDCJ | 6002| 100005825| 3501000001|Cement 50 kg | 1|pkt | 25-DEC-2013| 14-dec-2013--------------------------------------------------------------------------------------------------------------------------------------------------
where as source file is like that:-
Pending PR to process (detail report)
01-17-13 12:43:19 PM
Req.no. li Re Site Prj Id Act seq Part no Description Qty UOM want rec dt lat ord dt
MAT/250370 | 2| 1|ISCSP | 4977| 100004207| 0104000016|Angle 50 X 50 X 6 IS:2062 Grade | 5500|kg | 30-NOV-2012| 20-nov-2012
MAT/250370 | 3| 1|ISCSP | 4977| 100004207| 0105000002|Channel 100 X 50 IS:2062 Grade A | 1000|kg | 30-NOV-2012| 20-nov-2012
MAT/250579 | 2| 1|NMDCJ | 6001| 100005580| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 2991|kg | 13-DEC-2012| 03-dec-2012
MAT/250606 | 2| 1|NMDCJ | 6002| 100005860| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 4500|kg | 29-DEC-2012| 19-dec-2012
MAT/250607 | 2| 1|NMDCJ | 6001| 100005580| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 1500|kg | 29-DEC-2012| 19-dec-2012
MAT/250194 | 3| 1|NMDCJ | 6002| 100005818| 0109020002|TMT Bar 10 mm Fe 415 IS:1786 | 3939|kg | 29-DEC-2012| 19-dec-2012
MAT/250606 | 4| 1|NMDCJ | 6002| 100005860| 0109020004|TMT Bar 16 mm Fe 415 IS:1786 | 39000|kg | 29-DEC-2012| 19-dec-2012
MAT/250607 | 4| 1|NMDCJ | 6001| 100005580| 0109020004|TMT Bar 16 mm Fe 415 IS:1786 | 17500|kg | 29-DEC-2012| 19-dec-2012
MAT/250194 | 2| 1|NMDCJ | 6002| 100005818| 0109020004|TMT Bar 16 mm Fe 415 IS:1786 | 12183|kg | 29-DEC-2012| 19-dec-2012
MAT/250606 | 6| 1|NMDCJ | 6002| 100005860| 0109020006|TMT Bar 25 mm Fe 415 IS:1786 | 9500|kg | 29-DEC-2012| 19-dec-2012
MAT/250607 | 6| 1|NMDCJ | 6001| 100005580| 0109020006|TMT Bar 25 mm Fe 415 IS:1786 | 4500|kg | 29-DEC-2012| 19-dec-2012
MAT/250194 | 6| 1|NMDCJ | 6002| 100005818| 0109020006|TMT Bar 25 mm Fe 415 IS:1786 | 17500|kg | 29-DEC-2012| 19-dec-2012
MAT/250607 | 7| 1|NMDCJ | 6001| 100005580| 0109020008|TMT Bar 32 mm Fe 415 IS:1786 | 22000|kg | 29-DEC-2012| 19-dec-2012
MAT/250194 | 7| 1|NMDCJ | 6002| 100005818| 0109020008|TMT Bar 32 mm Fe 415 IS:1786 | 27060|kg | 29-DEC-2012| 19-dec-2012
MAT/251138 | 1| 1|NMDCJ | 6002| 100005825| 3501000001|Cement 50 kg | 1 |pkt | 25-DEC-2013| 14-dec-2013
Ignore alignment. It is well formatted in source file. -
Fading between two pages & controlling one MC from another.
Let me see if I can explain this properly. I usually use a motion tween and the alpha channel to fade movie clips in or out. What I am currently trying to do is fade one page out and another in, but it could be one of several MCs. I basically have four "pages" for a website including services, portfolio, about, and contact. I have icons on my navigation bar (which is going to be imported into my XHTML seperately so it can float them according to the users window size). The icons need to navigate between the pages and the pages need to fade in and out (eg. fade in the Services MC when the user clicks on the services icon, and fade out of it and into the Portfolio MC when the user clicks on the portfolio icon). Please keep in mind that the icons and pages are in completely different .fla/.swf files because I couldn't figure out how to float them in Flash after several hours of looking around online, but know I can easily do it using div tags + CSS in XHTML.
If someone could quickly explain how to "gotoandplay" a label in a different .swf file (communicate between the .swf NavBar and my main .swf) as well as fade out of the current MC (whichever page the user is currently on) before fading into new page (according to the icon the user clicks on), I'm sure I could 'fill in the blanks' from the rest of the AS3 and Flash I already know. The page also needs to fade out of whatever page it's currently on when the user clicks on the hide button (located on the page in the main .swf file). There is also several subpages on each page (which shouldn't be a big deal if I can figure the rest of this out).
I'm going to be using this same concept for nearly all of the websites I design & develop in the future and really need to know how to do this for the current site I'm working on. I would greatly appreciate any suggestions on how to accomplish these two things.
P.S. Please keep in mind I'm not an advanced user in AS3, but am very computer savy, and have done my share of programming in the past. I looked around for hours online to try and complete this without using the forum, but have come up with links to dead tutorials and short answers left and right. I'm hoping I won't come across the same here.
From what I've read so far I believe I can use tweening in ActionScript instead of a motion tween on the timeline to fade in and out of clips and believe that's the method to use to accomplish what I'm trying to do. Correct me if I'm wrong though.I'm not looking for a "tutorial created especially for me".... Just perhaps someone that can copy and paste some code from a similar project that they have done so I understand how to do it.
You could have simply put here's a tutorial for how to use TweenLite to crossfade between four pages, and here's one that will let you pass information between two .swf files. If you recently watched the tutorials then it wouldn't take long to find them (maybe you have them bookmarked) and post a couple links.
Anyways, I just found an excellent tutorial on how to crossfade using TweenLite (found here) and an article that explains how to pass information from one .swf to another (here). It took some searching and knowing exactly what I was looking for to find them, but that's a much better answer for someone looking to do those two things than I've found here (or elsewhere for that matter). -
Problem with replicated partitioning between two BSO db's. version 9.3.0.1
Hi there,
I have a problem with partitioning between two BSO db’s.
I created the partition, it validates and I made an export for the partion definiton(xml file).
Everything is fine if I set this partition up as transparent partition.
This means I can see the data from the src in the trg db as ecpected.
But when I change over to replicated (what in fact I want to do) nothing happens for the trg site - there are still no data. (Yes I have choosen Update all cells.)
I got no error in any way neither AAS nor in the app logs of src and trg.
(Mayby this it important: one src-dimension is mapped to void for the trg.)
Can anyone give me a hint or even confirm this behaviour ?
Thank you in advance
Andre
Below the log infos:
log of src db:
[Fri Dec 04 15:29:03 2009]Local/AAA///Info(1013210)
User [hyperion] set active on database [db]
[Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1013091)
Received Command [PutReplicatedCells] from user [hyperion]
[Fri Dec 04 15:29:03 2009]Local/AAA///Info(1013210)
User [hyperion] set active on database [db]
[Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1013091)
Received Command [XferReplicatedCells] from user [hyperion]
[Fri Dec 04 15:29:03 2009]Local/AAA///Info(1013214)
Clear Active on User [hyperion] Instance [1]
[Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1023005)
Update of replicated partition elapsed time : [0] seconds
[Fri Dec 04 15:29:03 2009]Local/AAA/db/hyperion/Info(1243010)
Partition refreshed
log of trg db:
[Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013210)
User [hyperion] set active on database [db]
[Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1013091)
Received Command [ReqXferReplicatedCells] from user [hyperion]
[Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013210)
User [hyperion] set active on database [db]
[Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1013091)
Received Command [ProtocolXchg] from user [hyperion]
[Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1023044)
Processing distributed request from [P4B5A856A, AAA, db]
[Fri Dec 04 15:29:03 2009]Local/AAA1/db/hyperion/Info(1013091)
Received Command [PutLastUpdatedTime] from user [hyperion]
[Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013214)
Clear Active on User [hyperion] Instance [1]
[Fri Dec 04 15:29:03 2009]Local/AAA1///Info(1013214)
Clear Active on User [hyperion] Instance [1]It sounds like you are doing it all correctly. One thing you might try just to be sure you are not getting any data in the target database is the following:
1) clear the target database
2) Run the replication for all cells
3) Run an export of all data on the target database
See if you get anything in the export file, maybe you are getting some of the data or possibly it is a rollup issue. Just a thought.
Jeff -
Google maps "get directions" between two points stopped working in firefox
When using google maps to find directions between two points "Get Directions" it will just sit there loading... never finishing and showing the routes between the locations.
This used to work fine about a month ago. I have not done anything, expect update Firefox.I can still get the basic directions to work in Google Maps, but recently the 3D driving directions has stopped working, and I'm pretty sure it stopped just about one Firefox update back. I realize this function is gravy to many people - a toy - but for someone who uses visual cues it has been extremely useful for imprinting the information in my mind, familiarizing myself with the route ahead of the drive. When I am traveling without a 'navigator' - a passenger who can read the directions as I drive - this is a huge help. Today I got a message about updating the GoogleEarth plugin, which I did - twice! Still no 3d directions, though suddenly the GG 3d driving simulator works. This has to be a FF problem :-(
-
Mirrored Storage between two servers
Hello,
Is it possible to create redundant storage using two Windows 2012 r2 servers? I've been looking all over and any HA options always reference having external shared storage presented to the cluster (I assume NAS/SAN). I am also assuming that said
posts expect that whatever tech is being used for shared storage deals with keeping that data fault tolerant (e.g., mirrored SAN) and the Windows cluster need not be aware of that happening in the background.
Due to lack of any storage hardware in my environment I was hoping there was a way to create a redundant file share/system between two Windows 2012 r2 servers at which point I could then create an iSCSI target to present a virtual drive to an application
server cluster. That way if one of the "storage servers" fails it won't take down the application running on the app server. I looked into DFS however since the app locks its files those won't replicate across.
I hope my question wasn't too convoluted.
Thanks for any guidance!Hi Bkboudreau,
If I am not misunderstand your question, you are finding the method for iSCSI target servers synchronize iSCSI data.
Replication of data between sites is very important in a multi-site cluster, and is accomplished in different ways by different hardware vendors. You can choose the hardware
storage vendor solution when you want to synchronize data between two shared storage.
You cannot use the feature in Windows Server 2008 called Distributed File System Replication (DFS-R) as your data replication method in a multi-site cluster. DFS-R only performs
its data replication after a file is closed. This works well for files such as documents, presentations, or spreadsheets, but it will not work for files that are held open, such as databases or virtual machines. You must choose a replication option other than
DFS-R.
The related KB:
Requirements and Recommendations for a Multi-Site Failover Cluster
http://technet.microsoft.com/zh-cn/library/dd197575(v=ws.10).aspx
The similar thread:
how to sync the data between the two iSCSI target server
http://social.technet.microsoft.com/Forums/windowsserver/en-US/067ba543-369c-4d22-9f00-1f41d7aedc00/how-to-sync-the-data-between-the-two-iscsi-target-server?forum=winserverClustering
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Stock transfer order between two storage locations in IS Retail
Hi,
I want to have a Stock transfer order between two storage locations in the plant.
I have activated the "Activate Stock Transfer Between Storage Locations", now i can create a STO and have the "Issuing SLoc" tab.
Having that i get an error message "Not possible to determine shipping data for material XXX" Message no. 06280.
I am trying to have the shipping data in customizing for set stock transfer - "Define Shipping Data for Plants", but my site is not listed due to the use of IS Retail. Is there a way to configure it?
Tnx
LiorHola.
Voy a contestar tu pregunta en espanol. Debes crear al centro emisor como deudor en la transaccion WB02 y ampliar a la organizacion de compra.
Posterior, debes crear al centro receptor como acreedor en la transaccion wb02.
Cesar Moreno. Funcional MM Retail.
Maybe you are looking for
-
How can i load the Marketing Attributes of the Business partner into BI. Is there any standard data souce??? what does it load into, the BP object??? Thank you
-
Lost my Apple link to Apple website downloads in Dock
Yesterday, I dragged the @ button from dock to trash by mistake and cannot get this back. I also now have upgraded to Leopard but would really want the button back. Can anyone help please? Thanks Sarah
-
Problem importing PSD (with multiple groups and layers) into After Effects. Help!
I created a "comic strip" in photoshop (multiple rectangle shape layers, then various shapes within each box for each frame of the comic strip) that I want to import into AE. When I import it as a composition (to keep my layers), however, what appear
-
Can't write to one array - error -50
I have an XServe RAID with a 7 disk 3TB RAID 5 volume on one side and a 4 disk 1.2TB RAID 5 volume on the other side. I am suddenly no longer able to write to the 3TB volume. The smaller volume works fine. The same error (-50) occurs from a client tr
-
Restriction with multiple variables for a characteristic present in Row
Hi all, I am facing a problem when I am restricting a characteristic in the 'defaut value' section of the filter tab. Details of the problem is given below: Characteristic is restricted by 3 variables. When I execute the query for the first time ther