MIDI won't Record

The audio will play (if I select an audio track). I updated to Logic X Pro 10.0.7 and use a MacBook Pro 8,1 with OS X 10.9.4 Mountain Lion. My interface (Scarlett 6i6) and instrument are connected and recognized through the Audio MIDI utility. Did the Logic X Pro update cause this error? Is there a bug in the update? Previously, I was able to record both MIDI and audio. I tried using the previous MIDI environments I set up, but they don't work anymore.

Sorry, the OS should be OS X 10.9.4 Mavericks.

Similar Messages

  • Midi Keyboard Won't Record On My Computer.  Need to figure this out quickly

    Well it'll record, but sound only plays when my synthesizer (A Juno G) is connected. Once I disconnect it, an error message pops up and no sound is played from the recording. This is pretty useless to me since I won't use the synthesizer for live performances, just for at home recording. There has to be a way to record sounds directly from the keyboard, though the USB Midi port that I'm using, and into logic just like my MPK49 does. The whole reason I bought the synthesizer was to use the built-in sounds for my music.
    Also, I searched through my keyboard and Logic manual and I do have the synthesizer's driver installed and all that stuff so I'm thinking it must just be a setting I have wrong.

    Krewtaun wrote:
    Ok so the audio output would be a port that wasn't midi then?
    Besides the midi usb output, it has a separate midi in and midi out as well as 4 individual A and B output jacks and the headphones jack. I'm assuming that I would have to get some sort of connector to use with the output jacks so I can connect it with my computer.
    I tried connecting just a double male sided headphone jack wire to the synth and my computer but that doesn't work either. Didn't expect it to allow me to record from the synth onto my computer, but I figured it would play the juno through my computer speakers. It doesn't, though.
    So how would I get Logic to play back the MIDI track and record the audio at the same time?
    First, in the Preferences/Audio section you have to set the audio to built-in (not mic) Then you may have to go to Utilities/Audio MIDI Setup and select Line-in as the Audio Input.
    The Headphone jack to computer should have worked, set the volume on the juno at 1/2 to start. The headphone output goes to the Line-in on the mac.
    Someone else will have to jump in here as I need to start rehearsal work and need to empty any technical stuff out of my brain!
    Good luck
    Oh, you record a MIDI track (create an external MIDI track) Set the Midi Interface to the Juno (probably already is) record the MIDI track, edit it, play it back while recording an audio track.
    You REALLY need to sit down, read and learn what you're doing.
    You can't expect the forum to help you every step of the way, how do you think we all learned?
    pancenter-

  • Error Result Code -48?  Help...won't record!

    I use G-band for basic VO recording in my home studio into my Powerbook. I run a simple stereo line-in and record to a completely basic stereo track. Nothing fancy. This has worked flawlessly for months.
    Just now, in mid-session, I click on the red Record button and I get this message: Error Result Code -48. It doesn't begin to record at all. The message is immediate, and it won't record.
    This program is pretty vital to my business. Can anyone help me figure this out?? I have restarted the program, shutdown and restarted the Powerbook. No luck.
    Any help?!
    ge

    You could try some web searches. I just know some of them because I've run into them while programming, and have some notes scattered about here and there for some of the less common ones, but not all of them.

  • Quickplay won't record a VCR input from a USB Pinnacle TV stick.

    If I try to record a VCR movie (camcorder type) with Quickplay, it's says, "This content is protected and cannot be recorded". What I've noticed is it seems to only be the analog input from the Pinnacle device. Media Center can record it, but the bottom of the video is distorted. It looks good when played in Quickplay, but won't record. Anyone seen this or have any ideas? Thanks.

    maskeda wrote:
    I got it, some how it was a MIDI track and not an audio track.
    "Some How"?     as in:  user error? 

  • New sound card (E-MU 1212M) won't record higher than 48kHz

    I'm running Windows XP Pro/SP2 with a 2.8GHz Pentium 4 processor (motherboard is Elitegroup 848P-A). I have 1GB of RAM installed.
    I do a lot of vinyl transfer work. I decided to upgrade sound cards to the E-MU 1212M to improve the overall quality of my audio.
    The card install went well. I'm receiving an audio signal just fine. I can playback at 44.1, 48, 96, 192.
    The only hitch is when I try to record. I can record at 44.1 & 48 but if I try to record at 96 or 192 I get the following message:"Another application has caused a sample rate change that makes the current session invalid. You may accept this change by loading session at the new sample rate indicated below...." The sample rate that it shows me is always 44.1 So when receiving this message it always wants to push me back to 44.1 This message pops up immediately after I hit the red "record" button.
    There are no other audio applications similar to Audition installed on my set up. I have turned off the system sounds, the 1212M card is recognized as the default audio device. The on-board sound card has been disabled along with its drivers. Gone also are the drivers from my previous sound card.
    The settings between the 1212M and Audition are following along with each other. If I set the 1212M for 44.1, 48, 96, or 192 and then open up Audition and check the hardware settings, its at whatever I had set the 1212M to.
    Ive also gone through what items are being loaded during start-up of my computer. Ive tried disconnecting from the internet and shutting down all programs that might be active, ensuring that no other programs are running other than Au 3 and the 1212M PatchMix panel.
    Any suggestions?
    Thanks for your time.
    -DLedin

    "Before you did that, did you start a new session at 96k, and it still won't record into it? "
    If you're asking if I first start a new session in PatchMix, yes, that's correct. I call up the 96k session in PatchMix first. Then I go and open up Audition to try to record.
    If you're asking me if I start a new session in Audition 3 first, then I'm not sure exactly what you mean by that. Remember, I'm new to Au 3. When working in Audition 1.5, I could hit the "record" button and a window would pop up, prompting me to enter a sample rate and bit depth for the audio I'm about to record. I enter what I want to do and press "OK", then Audition starts to record. I don't know if that window is what you're referring to as a "session".
    If that is a what you mean by "session" then I would need to do some experimenting by setting PatchMix to 44.1, then open up Audition, hit "record", specify 96/24 in the window that pops up and see what happens. I would hope that I'd get a message from PatchMix that I need to go to set PatchMix for a 96k "session". That's actually a possibility I hadn't previously considered trying. I'm at work now but will look into this possibility after I'm back home & report back.
    -DLedin
    EDIT: Since my last reading of your message you added a question:"Also, when you set the session up, did you take the check out of the 'use default' box?"
    Please specify which application you're referring to when you say "session". PatchMix uses the term quite a lot. If there's a "use default" box somewhere that I need to take a look at then I need to know if it's in Audition 3 or PatchMix and just where to find it. Also, should that "use default" box be checked or unchecked? I appreciate your patience.

  • Can you use midi sounds when recording videos on Photobooth?

    Can you use midi sounds when recording videos on Photobooth?
    Basically, i like to record videos of me singing and playing guitar or keyboard, but to get a good sound for the keyboard I'd like to be able to record the audio using MIDI sounds...
    Ive got Logic, I've got M-Audio Fast Track Pro, into which i have my mic, guitar, and keyboard midi plaugged into. I can use it to record the mic and guitar on photobooth as they are audio inputs, however i can't use the midi sounds on the keyboard :/ I have tried having logic open with the desired MIDI sound selected whilst recording but it doesnt work...
    Is there ANY way this is possible?
    HELP PLEASE!
    Thanks!

    I Have just the same problem, if I shout very near the microphone i can just hear something, did you manage to solve the problem?

  • Using interface for recording.  Mic is selected and recognized but won't record., Using interface for recording.  Mic is selected and recognized but won't record.

    Help please!  I am using an interface to record vocals.  I've used it before without any problems but today it won't record.  Garageband recognizes the mic but for some reason it won't record.

    When you say nothing was touched, does that include a software update of any kind?
    Do you have Apple's auto update enabled?

  • My iphone 4 microphone won't record sound on video clips and doesn't work with Skype

    This is the first time I have used the forum. My iphone4 microphone won't record sound on video clips, and won't work with Skype.

    I have checked that I have the latest software. I have restarted phone. I am not sure how to perform the other things you mentioned , restore and reset as new... Would I lose any data by doing these? Thanks for the reply.

  • Can't hear Midi Software Instrument & Audio won't record

    I have used Logic in a basic way for years and have never had trouble but I reinstalled logic onto a new macbook and using a new interface.
    On launching a new project, I selected software instrument, and chose a yamaha piano studio. I can see that the MIDI signal is being received in Logic and will record but I cannot hear any sound.
    When audio track is selected, I can hear the sounds being picked up from the microphone in my headphones and can see it on logic...but when I try to record, no sound is recorded.
    Is this to do with output settings?
    I know its probably something very straightforward but I have been searching the forums for hours and can't seem to resolve.
    Interface: PreSonus AUDIOBOX USB.
    My keyboard (YAMAHA P-80) is connected correctly to the audiobox which in turn is connected to the computer.

    macuser84 wrote:
    Do I have to get a pre amp or something to boast the volume of the USB keyboard?
    you're recording MIDI, not audio, you can't "pre-amp" the digital signal.
    you can raise the instrument volume a bit more:
    http://www.bulletsandbones.com/GB/GBFAQ.html#midiinstrumentlouder
    (Let the page FULLY load. The link to your answer is at the top of your screen)

  • Logic Pro X keeps sending C0 notes to midi out when record is armed on a audio track

    I have a annoying problem with Logic Pro X, which I bought a month ago. Here's al little scenario that describes the problem.
    I disconnect my audio interface, so that Logic Pro has to rely on my MacBook Pro's internal audio. This way I exclude my RME-FF800 from being of any influence.
    I start up the Midi Monitor tool, to analyse what comes out of Logic; MIDI-wise.
    I start up Logic set up a small test project in Logic Pro X, that contains:1 audio track
    There's little button on the audio track with a red-colored "R". This is the button to "arm" this track for recording audio.
    I push the little "R" button, the R-character turns white, the button as a whole turns red. The button starts blinking.
    From this moment on Logic starts sending MIDI messages ....... huh?  Every second or so ... a low C.
    In my regular studio setup this means that I hear a low repeated note coming out of my piano, every time I record audio.  How annoying!!
    By the way ... a Guitar/Bass track has the same problem. All the other track types (External midi, software instrument, drummer) don't have this problem.
    Help is deeply appreciated, because it drives me crazy and if I can't fix this .... I think I have to return to my previous DAW-of-choice (Cubase 7.5).
    Here's the Midi Monitor output.
    20:46:01.241          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:02.008          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:02.774          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:03.541          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:04.308          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:05.075          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:05.841          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:06.608          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:07.374          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:08.140          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:08.908          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:09.675          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:10.441          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:11.208          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:11.975          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:12.741          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:13.507          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:14.274          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:15.043          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:15.808          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    20:46:16.574          To MIDI Monitor (midi monitor)          Note On          2          C0          127
    20:46:17.341          To MIDI Monitor (midi monitor)          Note Off          2          C0          0
    Logic Pro X = version 10.0.6
    Mac Book Pro = late 2008.
      Model Name:          MacBook Pro
      Model Identifier:          MacBookPro5,1
      Processor Name:          Intel Core 2 Duo
      Processor Speed:          2,53 GHz
      Number of Processors:          1
      Total Number of Cores:          2
      L2 Cache:          6 MB
      Memory:          4 GB
      Bus Speed:          1,07 GHz
      Boot ROM Version:          MBP51.007E.B06
      SMC Version (system):          1.33f8
    Mac OSX = 10.9.1
      System Version:          OS X 10.9.1 (13B42)
      Kernel Version:          Darwin 13.0.0
      Boot Volume:          Macintosh HD
      Boot Mode:          Normal
      Secure Virtual Memory:          Enabled

    The note is likely being sent out because of a Control Surface you have installed or used.... be it a hardware keyboard, controller or even an ipad controller app... such as Logic Remote or TouchOSC for example... or even an iOS software synth app that is sending midi over wireless....
    So.. first make sure you have force quit any iPad/iPhone Logic/midi related apps and not just closed them..
    Then if that doesn't fix things.. delete Logic's CS preferences... and Logic's own user preferences too...as described here..
    Delete the user preferences
    You can resolve many issues by restoring Logic Pro X back to its original settings. This will not impact your media files. To reset your Logic Pro X user preference settings to their original state, do the following:
    In the Finder, choose Go to Folder from the Go menu.
    Type ~/Library/Preferences in the "Go to the folder" field.
    Press the Go button.
    Remove the com.apple.logic10.plist file from the Preferences folder. Note that if you have programmed any custom key commands, this will reset them to the defaults. You may wish to export your custom key command as a preset before performing this step. See the Logic Pro X User Manual for details on how to do this. If you are having trouble with a control surface in Logic Pro X, then you may also wish to delete the com.apple.logic.pro.cs file from the preferences folder.
    If you have upgraded from an earlier version of Logic Pro, you should also remove~/Library/Preferences/Logic/com.apple.logic.pro.
    Restart the computer.
    Do not forget to Quit Logic before doing this and then restart the Mac after doing this....

  • Final Cut Pro X won't record voiceover

    I was using FCPX 10.1.3 when this problem appeared, now I'm on 10.1.4 and it wasn't fixed.
    Here's the summary: when I open a "Record Voiceover" window everything works fine, I can select different input devices, set up event, I can even hear myself with Monitor enabled. But when I start recording I can see, that the audio file on the timeline is empty. After the recording stops I check it and it is empty. It literally didn't record my sound. I've tried different microphones and channels - nothing helped. I've tried to search the answer on Google and Apple Support, but was unable to find something that helped anyone. I also saw that many people have this problem, but I guess no one has posted the solution yet.
    I tried to delete the whole FCPX including Caches, PLISTs and other stuff hidden in Application Support. The only thing left was, obviously, Projects and Events. After reinstalling the app Voiceover still didn't work. I've also tried to change the System Language to English (my native language is Russian), but it also didn't help.
    The only answer on Apple Communities I found was "deleting the whole system or creating a new user", but I don't want to do it yet (also no one said that will work) because I want to try to find the right answer (or wait until Apple finally fixes it).
    I am using FCPX 10.1.4 on iMac 27" mid 2011

    Since this works for other users, there must be something on your system.
    You say you did a clean install. Did you try this immediately after installing?
    I ask this because if you did a clean install but then used Migration Assistant to bring back your user account, then you probably brough back the problem also!
    You never said if you tried doing a voice over from a different user account on the same system.  If you didn't, then I can only suggest you try it now.
    To create a new account, open System Preferences, click on "Users & Groups", click the padlock if necessary to allow changes, and hit the plus button to create a new user. Then login as that user and try a voiceover. I am guessing it will work.

  • Logic Pro X won't record from USB or builtin audio devices

    I have a M-Audio Fast Track and I've overcome the bugs regarding audio input and Mavericks by using a new mac and upgrading to Logic Pro X.  Now I have a new issue which I think is unrelated.
    I can hear the guitars in Logic Pro X when I turn the monitor on.  The track shows input levels, my guitar plugins work.  When I hit record I can record software instruments but when I try to record guitars or vocals nothing is ever recorded.  I even unplugged the M-Audio Fast Track and tried the mic input on the mac and have gotten the same results.
    Does anyone have any suggestions for this?

    maskeda wrote:
    I got it, some how it was a MIDI track and not an audio track.
    "Some How"?     as in:  user error? 

  • Is there a way to show/reveal the piano roll (or score) from a midi input when recording an audio track in Logic 9?

    I'm trying to record audio tracks in Logic 9 over midi tracks I've created using a software instrument.  I've done this before, and there used to be a no problem in seeing the midi information in the piano roll or the score while recording audio tracks, but it now impossible to reveal.  Has ayone else exerienced this?  Was there a change (update) that eliminated that as an option?  Or did I do something in preferences somewhere (unbeknownst to me when doing it) that has caused this?  Thanks for any suggestions.

    Just open the piano roll fro the regions you want and deselect the chain icon at the upper left.

  • Disappearing midi latency during recording

    Haven't see a discussion on this yet, any ideas?????
    When I go to record a midi performance, there is a delay of about 175 milliseconds, that after about 10 seconds disappears and allows the performance to properly align with the rest of the track. There is no audible delay when I am performing, only when I go to play the track back, and as I am watching the piano roll record in real time.
    I have tried resetting the logic preferences, and changing my midi keyboard. The midi keyboard is plugged directly into the MacPro. I'm troubleshooting in a new logic file with no extra plugins using the default EVP88. I'm using Logic 9.1.3.
    Much Obliged

    Update: It has something to do with my audio interface. I tried unplugging it and the problem stopped. I'm using the Audio Kontrol 1 from Native Instruments. Reinstalling the drivers for that now...

  • How to change midi velocities after recording?

    previously when I used EZdrummer i would just write out the beats using the piano roll and a mouse, and then i could easily click the little tab at the bottom of the piano roll and change the velocity of any note.
    But recently i've started actually recording through EZdrummer using my Roland electric drum kit. I recorded a whole song and then realized that my double pedal on the bass drum was set up a little crooked so the left foot didn't pick up as well, therefore all my left footed hits are quieter.
    i figured i could just go into the piano roll and change the bass hits and make them consistent, but instead of the normal separated orange lines i'm used to, the velocity shows up as one big blue line and i cant seem to adjust the velocities of individual drums.
    please help!

    There are so many ways of adjusting velocities in Logic.
    Spend a little time reading the manuals - read the piano roll chapter, the hyper edit chapter, the event list chapter.
    There is a velocity tool in the piano roll editor, so simply click on the note on the left (which will select all MIDI events on that note) and use the velocity tool to increase them.
    Lots of other ways as well, but that will get you started.

Maybe you are looking for

  • Quicktime 7.1 buffer overrun when trying to get info from an Indeo 4.4 AVI

    Surprisingly Quicktime7.1 can play one of my Indeo video 4.4-encoded Windows .AVI File. It plays and exports flawlessly but when I want to use Get Info the player (or maybe one of the QuickTime DLLs) crashed with a VC++ Runtime Error: Buffer Overrun.

  • Problem with column groups on Interactive Report

    Hi I am hoping that someone can help with this problem. I am attempting to control both the grouping and ordering within each group of fields in the single row view of an interactive report. Creating column groups appears to be OK at first (sequence,

  • Problem is Module pool custom F4 help

    In module pool selection screen . I have defined vendor field as a select option and attached a custom search help to it . Now the problem is that when i press F4 on that field and select a value from the help , that value is not populated in the inp

  • I'm trying to install my copy of CS5 under CS6 because

    I'm trying to install my copy of  CS5 under CS6 because my new Canon Pixma Pro-10 will not install a plugin of PrintStudioPro in CS6 but does install it in CS5, but the Adobe website says my SN for CS5 is correct but will not recognize it. Where do I

  • Moving songs in iTunes

    I have created a playlist, but I can't point/click and move a song into a specific place on the list... It seems to be preventing me from determing the order of songs in my playlist. Can anyone tell how to fix this or be able to move songs around???