Missing content on ACE module.

Hello
I'm working on a configuration and after a few tests I realized it does not bring the whole content of the site. Most of the times a picture of two are missing. The site is ebay-like with many pictures, banners and flash.
If I right-click âShow Pictureâ the image comes up right away.
For testing purposes and to be able to work along with the previous solution, NAT is set.
So far, I have tried:
I disabled sticky on every serverfarm. It was ON at the beginning.
I changed the predictor. From response app-req-to-resp samples 4 to leastconns slowstart 30.
I tried IE7 and Firefox clearing caches and so.
I set OUTOFSERVICE different servers and made combinations in an attempt to identify a rogue server.
The show serverfarm detail showed failures a couple of times but I later realized it was not related because further testing showed missing content and a steady counter.
No resources were ever denied.
The solution to be replaced by the ACE works fine.
The installed version is c6ace-t1k9-mz.A2_1_1a.bin.
Any advice?
Thanks a lot.
Guido

You did a lot of things wihtout knowing what exactly is going in the network.
The first step in troubleshooting an issue with ACE is to capture a sniffer trace of the tengig interface.
See if the server is sending redirect, or if packets are dropped, ...
Once you have the trace, if you can't see the problem send it to us with the config.
Gilles.

Similar Messages

MAC-Miss Rate on ACE module

What exactly does the MAC-Miss rate mean on the ACE? And if we are running out of resources for it, should I worry?
We have only implemented 1 production policy on the ACE module so far and we are already running out of resources for the mac-miss rate. All other resources look good.
Is this OK? Or is something wrong here?
Attached is the resource usage counters.
Thanks,
Ben

When the ACE receives traffic for which it does not have an arp entry for either the source or destination, this is called a mac-miss and the fastpath agent needs to ask the slowpath agent to perform an arp request.
This communication is rate-limited.
With no mac entry for a src or dst, we drop the packet.
So, you should increase the resource.
Or review your design.
It's best to have the clients coming through a gateway (ie: the MSFC) instead of directly accessing the ACE.
This way only 1 mac entry is needed - the gateway.
You'll see a counter like this
switch/Admin# sho np 1 me-stats "-socm -v" | i mac
Drop [mac lookup fail]: 4 0
Gilles.

Cisco ACE module missing licence file - no connectivity

Hi,
We have 2 ACE modules that were delivered without any licenses.
There is no IP connectivity whatsoever to these modules and I'm guessing this is due to the fact there are no licenses installed.
Have tried asking Cisco to no avail - and am not sure if there is an actual problem with them or not.
The VLANs are assigned correctly and I can see inbound ICMP echo from the 6509 that its hosted in, but no outbound packets ever leave the ACE. I've applied a mgmt policy to enable ping/telnet/ssh etc.
switch/Admin# sh vlans
Vlans configured on SUP for this module
vlan4 vlan30-31 vlan160 vlan180-195 vlan360 vlan380-395 vlan560 vlan580-
595 vlan760 vlan780-795
switch/Admin# sh ip int bri
Interface       IP-Address      Status                  Protocol
vlan4           10.119.127.196 up                      up
vlan30          10.119.127.241 up                      up
vlan31          10.119.127.245 up                      up
interface vlan 4
description ACE Mgmt interface for Admin Context
ip address 10.119.127.196 255.255.255.224
service-policy input REMOTE_MGMT
no shutdown
vlan4 is up
Hardware type is VLAN
MAC address is 00:1f:ca:7b:6f:33
Mode : routed
IP address is 10.119.127.196 netmask is 255.255.255.224
FT status is non-redundant
Description:ACE Mgmt interface for Admin Context
MTU: 1500 bytes
Last cleared: never
Alias IP address not set
Peer IP address not set
Assigned from the Supervisor, up on Supervisor
Config download failures : 1
     2980 unicast packets input, 16363862 bytes
     240857 multicast, 3026 broadcast
     0 input errors, 0 unknown, 0 ignored, 0 unicast RPF drops
     0 unicast packets output, 187712 bytes
     0 multicast, 2933 broadcast
     0 output errors, 0 ignored
switch/Admin# sh arp
Context Admin
================================================================================
IP ADDRESS      MAC-ADDRESS        Interface Type      Encap NextArp(s) Status
================================================================================
10.119.127.193 00.00.00.00.00.00 vlan4     GATEWAY    -       * 3 req     dn
10.119.127.196 00.1f.ca.7b.6f.33 vlan4     INTERFACE LOCAL     _         up
10.119.127.245 00.1f.ca.7b.6f.33 vlan31    INTERFACE LOCAL     _         up
10.119.127.241 00.1f.ca.7b.6f.33 vlan30    INTERFACE LOCAL     _         up
================================================================================
Total arp entries 4
The ARP table for the adjacent switch SVI has a valid MAC upon reboot, but soon after resets to 00.00.00.00.00.00
Problem is that once Cisco eventually send me the license file I have no way of TFTP'ing it to the ACE module.
Any suggestions/advice?

Thanks for the info - so I should at least be able to connect to a license-less ACE at least, but these modules seem to have a problem.
If the modules are reloaded (from the ACE) or reset (from the Supervisor) they initially have the ARP entry (however still cannot communicate to the attached Supervisor via SVI) which eventually resets.
Info as requested:
switch/Admin# sh resource usage
                                                     Allocation
        Resource         Current       Peak        Min        Max       Denied
Context: Admin
conc-connections              9          9          0          0          0
mgmt-connections              0          0          0          0          0
proxy-connections             0          0          0          0          0
xlates                        0          0          0          0          0
bandwidth                     0         76          0 125000000 296849008
    throughput                  0         76          0          0 296849008
    mgmt-traffic rate           0          0          0 125000000          0
connection rate               0          2          0          0         15
ssl-connections rate          0          0          0          0          0
mac-miss rate                 0          0          0          0          0
inspect-conn rate             0          0          0          0          0
acl-memory                    0       6336          0          0         11
sticky                        0          0          0          0          0
regexp                        0          0          0          0          0
syslog buffer                 0          0          0          0          0
syslog rate                   0          0          0          0         24
Context: APPLICATION
conc-connections              0          0    2000000          0          0
mgmt-connections              0          0      25000          0          0
proxy-connections             0          0     262144          0          0
xlates                        0          0     262144          0          0
bandwidth                     0          0 125000000 125000000          0
    throughput                  0          0 125000000          0          0
    mgmt-traffic rate           0          0          0 125000000          0
connection rate               0          0     250000          0          0
ssl-connections rate          0          0        250          0          0
mac-miss rate                 0          0        500          0          0
inspect-conn rate             0          0       1500          0          0
acl-memory                    0          0   19650480          0          0
sticky                        0          0     419430          0          0
regexp                        0          0     262144          0          0
syslog buffer                 0          0    1048576          0          0
syslog rate                   0          0      25000          0          0
Context: BACK_END
conc-connections              0          0    2000000          0          0
mgmt-connections              0          0      25000          0          0
proxy-connections             0          0     262144          0          0
xlates                        0          0     262144          0          0
bandwidth                     0          0 125000000 125000000          0
    throughput                  0          0 125000000          0          0
    mgmt-traffic rate           0          0          0 125000000          0
connection rate               0          0     250000          0          0
ssl-connections rate          0          0        250          0          0
mac-miss rate                 0          0        500          0          0
inspect-conn rate             0          0       1500          0          0
acl-memory                    0          0   19650480          0          0
sticky                        0          0     419430          0          0
regexp                        0          0     262144          0          0
syslog buffer                 0          0    1048576          0          0
syslog rate                   0          0      25000          0          0
Context: FRONT_END
conc-connections              0          0    2000000          0          0
mgmt-connections              0          0      25000          0          0
proxy-connections             0          0     262144          0          0
xlates                        0          0     262144          0          0
bandwidth                     0          0 125000000 125000000          0
    throughput                  0          0 125000000          0          0
    mgmt-traffic rate           0          0          0 125000000          0
connection rate               0          0     250000          0          0
ssl-connections rate          0          0        250          0          0
mac-miss rate                 0          0        500          0          0
inspect-conn rate             0          0       1500          0          0
acl-memory                    0          0   19650480          0          0
sticky                        0          0     419430          0          0
regexp                        0          0     262144          0          0
syslog buffer                 0          0    1048576          0          0
syslog rate                   0          0      25000          0          0
Context: TEST_DEV
conc-connections              0          0    2000000          0          0
mgmt-connections              0          0      25000          0          0
proxy-connections             0          0     262144          0          0
xlates                        0          0     262144          0          0
bandwidth                     0          0 125000000 125000000          0
    throughput                  0          0 125000000          0          0
    mgmt-traffic rate           0          0          0 125000000          0
connection rate               0          0     250000          0          0
ssl-connections rate          0          0        250          0          0
mac-miss rate                 0          0        500          0          0
inspect-conn rate             0          0       1500          0          0
acl-memory                    0          0   19650480          0          0
sticky                        0          0     419430          0          0
regexp                        0          0     262144          0          0
syslog buffer                 0          0    1048576          0          0
syslog rate                   0          0      25000          0          0
switch/Admin# sh cde health
CDE BRCM INTERFACE
======================
Packets received                                             3357
Packets transmitted                                            12
Broadcom interface CRC error count                              0
BRCM VOQ status                           [empty]      [not full]
BRCM pull status                                        [pulling]
CDE HYPERION INTERFACE
======================
Packets received                                          7668407
Packets transmitted                                        967915
Short packets drop count                                        0
Fifo Full drop count                                            0
Protocol error drop count                                       0
FCS error drop count                                            0
CRC error drop count                                            0
Num times flow control triggered on hyp interface                0
Num self generated multicast packets filtered              967915
HYP IXP0 VOQ status                       [empty]      [not full]
HYP IXP1 VOQ status                       [empty]      [not full]
HYP SLOW VOQ status                       [empty]      [not full]
HYP tx pull status                                      [pulling]
CDE IXP0 INTERFACE
======================
Packets received                                           964680
Packets transmitted                                       6581196
Num bad pkts recvd on fast spi channel0                         0
Num bad pkts recvd on slow spi channel8                         0
Num bad pkts recvd on fast spi channel2                         0
Num bad pkts recvd on slow spi channel4                         0
IXP0 Fast VOQ status                      [empty]      [not full]
IXP0 BRCM VOQ status                      [empty]      [not full]
IXP0 pull status                                        [pulling]
IXP0 spi src status                                     [healthy]
IXP0 spi snk status                                     [healthy]
CDE1 SWITCH1 INTERFACE
======================
Packets received (hyp, ixp0)                                 3241
Packets received (bcm)                                          6
Packets received (daughter card 0)                              0
Packets received (daughter card 1)                              0
Packets Errors received (hyp, ixp0)                             0
Packets Errors received (bcm)                                   0
Packets Errors received (daughter card 0)                       0
Packets Errors received (daughter card 1)                       0
Packets transmitted (ixp1)                                 122653
Packets transmitted (nitrox)                                    0
Packets Errors transmitted (ixp1)                               0
Packets Errors transmitted (nitrox)                             0
CDE2 SWITCH2 INTERFACE
======================
Packets received (ixp1)                                    122653
Packets received (nitrox)                                       0
Packets Errors received (ixp1)                                  0
Packets Errors received (nitrox)                                0
Packets transmitted (hyp, ixp0)                              3241
Packets transmitted (broadcom)                                  6
Packets transmitted (daughter card 0)                           0
Packets transmitted (daughter card 1)                           0
Packets Errors transmitted (ixp1)                               0
Packets Errors transmitted (nitrox)                             0
Packets Errors transmitted (daughter card 0)                    0
Packets Errors transmitted (daughter card 1)                    0
CDE IXP1 INTERFACE
======================
Packets received                                             3247
Packets transmitted                                        122653
Num bad pkts recvd on fast spi channel0                         0
Num bad pkts recvd on slow spi channel8                         0
Num bad pkts recvd on fast spi channel2                         0
Num bad pkts recvd on slow spi channel4                         0
IXP1 Fast VOQ status                      [empty]      [not full]
IXP1 BRCM VOQ status                      [empty]      [not full]
IXP1 pull status                                        [pulling]
IXP1 spi src status                                     [healthy]
IXP1 spi snk status                                     [healthy]
CDE NITROX INTERFACE
======================
Packets received                                                0
Packets transmitted                                             0
Num bad pkts recvd on fast spi channel0                         0
Num bad pkts recvd on slow spi channel8                         0
Num bad pkts recvd on fast spi channel2                         0
Num bad pkts recvd on slow spi channel4                         0
NTX Fast VOQ status                       [empty]      [not full]
NTX BRCM VOQ status                       [empty]      [not full]
NTX pull status                                         [pulling]
NTX spi src status                                      [healthy]
NTX spi snk status                                      [healthy]
== Backplane ==
ITASCA_SYS_CNTL1 0x300 data 0x61f0000
ITASCA_SYS_CNTL2 0x304 data 0x80630000

Reuse of context in ACE module

Hi all, just have a question about som reuse of resources in a ACE module context. I don't want to make a new context, and can reuse most of the existing configuration in one of my context. The config is not complex and difficult, but I'm not sure if I can do this.
The primary goal is to loadbalance 2 webservers with a new vip, new serverfarm, stickygroup, policy-map and different nat-pool.
Since I haven't decided the ip addresses to be used, they are just xx in the config below.
The changes I want to implement are in bold. Will this work for me?
probe http WEBGUI_D2
description Probe for http mot webgui
interval 10
passdetect interval 10
passdetect count 1
request method get url /D2/auth/login.aspx
expect status 200 302
header User-Agent header-value "IDENTITY"
rserver host cwi003
description content server logon
ip address 10.163.22.27
inservice
rserver host cwi004
description content server logon
ip address 10.163.22.28
inservice
rserver host cwi503
description content server logon 2
ip address 10.163.22.23
inservice
rserver host cwi504
description content server logon 2
ip address 10.163.22.24
inservice
serverfarm host SF_LOGON_D2
probe WEBGUI_D2
rserver cwi003 80
   inservice
rserver cwi004 80
   inservice
serverfarm host SF_LOGON2_D2
probe WEBGUI_D2
rserver cwi503 80
   inservice
rserver cwi504 80
   inservice
sticky ip-netmask 255.255.255.255 address source STICKYGROUP1
timeout 20
replicate sticky
serverfarm SF_LOGON_D2
serverfarm SF_LOGON2_D2
class-map match-all VS_LOGON_D2
3 match virtual-address 10.163.22.13 any
class-map match-all VS_LOGON2_D2
3 match virtual-address 10.163.22.xx any
policy-map type loadbalance first-match PM_ONE_ARM_LB
class class-default
   sticky-serverfarm STICKYGROUP1
policy-map multi-match PM_ONE_ARM_MULTI_MATCH
class VS_LOGON_D2
   loadbalance vip inservice
   loadbalance policy PM_ONE_ARM_LB
   nat dynamic 5 vlan 1240
class VS_LOGON2_D2
   loadbalance vip inservice
   loadbalance policy PM_ONE_ARM_LB
   nat dynamic 6 vlan 1240
interface vlan 1240
description Client_server
ip address 10.163.22.11 255.255.255.0
peer ip address 10.163.22.12 255.255.255.0
access-group input INBOUND
nat-pool 5 10.163.22.14 10.163.22.17 netmask 255.255.255.192 pat
nat-pool 6 10.163.22.xx 10.163.22.xx netmask 255.255.255.192 pat
service-policy input PM_ONE_ARM_MULTI_MATCH
no shutdown
ip route 0.0.0.0 0.0.0.0 10.163.22.1
BR
Geir

Thanks for your reply.
Hope I understand you correct. This sould be the config I need to paste into the existing context.
rserver host cwi503
description content server logon 2
ip address 10.163.22.23
inservice
rserver host cwi504
description content server logon 2
ip address 10.163.22.24
inservice
serverfarm host SF_LOGON2_D2
probe WEBGUI_D2
rserver cwi503 80
    inservice
rserver cwi504 80
    inservice
sticky ip-netmask 255.255.255.255 address source STICKYGROUP2
   timeout 20
   replicate sticky
   serverfarm SF_LOGON2_D2
class-map match-all VS_LOGON2_D2
   3 match virtual-address 10.163.22.xx any
policy-map type loadbalance first-match PM_ONE_ARM_LB2
class class-default
    sticky-serverfarm STICKYGROUP2
policy-map multi-match PM_ONE_ARM_MULTI_MATCH
class VS_LOGON2_D2
    loadbalance vip inservice
    loadbalance policy PM_ONE_ARM_LB2
    nat dynamic 6 vlan 1240
interface vlan 1240
nat-pool 6 10.163.22.xx 10.163.22.xx netmask 255.255.255.192 pat
Br
Geir

Simple SLB with the ACE Module

Hello,
i have some problems with a ACE module i am currently tesing.
I have a simple Serverfarm with two Servers.
But there seems to be some Problems with the Loadbalancing i not understand:
1) I use Round Robin, but the ACE seems to put me serval times to the same server. I notice this, because i have different content on both servers, also different URLs.
2) withz the show serverfarm statement the total connects do not increment.
switch/slb-c1# show serverfarm webfarm
serverfarm : webfarm, type: HOST
total rservers : 2
----------connections-----------
real weight state current total
---+---------------------+------+------------+----------+--------------------
rserver: web1
10.0.33.201:0 8 OPERATIONAL 0 0
rserver: web2
10.0.33.200:0 8 OPERATIONAL 0 0
switch/slb-c1# show service-policy L4_LB_VIP
Status : ACTIVE
Interface: vlan 300
service-policy: L4_LB_VIP
class: L4_VIP_CLASS
loadbalance:
L7 loadbalance policy: L7_SLB_POLICY
VIP Route Metric : 77
VIP Route Advertise : DISABLED
VIP ICMP Reply : ENABLED
VIP State: INSERVICE
curr conns : 0 , hit count : 15
dropped conns : 0
client pkt count : 10198 , client byte count: 420991
server pkt count : 23367 , server byte count: 34915173
I have attatched the Config.
Any Idea what is going on?

what version do you have ?
I would recommend to run the very recent A1.4.
This is something that really should work.
Gilles.

ACE MODULE IN BRIDGE MODE NOT LOADBALANCING

Hi,
I setup an ace module in bridge mode as follows:
mfsc(vla80) > (vla80)outside fwsm, fwsm inside(vla40) > (vla40)ace-clientside, aceserverside(vla41)
and the servers have the fwsm svi(vla40) as their gateway. But, the ace is not loadbalancing.
The config script is attached. Is their anything I am missing?
Attach

Check my troubleshooting guide on this forum.
There are few things to do to narrow down the issue.
Gilles.

Certificates vanished - ACE Module. Strange!

ACE modules are configured in Active/Standby context mode on two distinct Cat6500's. The feature license is 10,000 SSL tps, 8Gbps throughput.
We ran the application performance tests with 1000 users with https transactions and I noticed that the all the root certificates under the chaingroup disappeared. Only the website certificate remained. When I accessed the website, it gave 'error with the security certificate' i.e. the root was not identifiable due to missing certificates. Eventually, the CPU went 100% on Cat6500 and the ACE module was shutdown by the chassis. It got reenabled automatically in 5 minutes.
I re-added the root certs, removed/added the service policy and after sometime I noticed the root certs disappeared again. STRANGE !
show version output is
Cisco Application Control Software (ACSW)
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2006, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
Software
loader: Version 12.2[121]
system: Version 3.0(0)A1(6.3a) [build 3.0(0)A1(6.3a) adbuild_02:16:25-2008/02/02_/auto/adbu-rel3/ws/rel_3_0_0_a1_6.3-thr
ottle/REL_3_0_0_A]
system image file: [LCP] disk0:c6ace-t1k9-mz.3.0.0_A1_6_3a.bin
installed license: ACE-08G-LIC ACE-VIRT-020 ACE-SSL-10K-K9
Hardware
Cisco ACE (slot: 2)
cpu info:
number of cpu(s): 2
cpu type: SiByte
cpu: 0, model: SiByte SB1 V0.2, speed: 700 MHz
cpu: 1, model: SiByte SB1 V0.2, speed: 700 MHz
memory info:
total: 957640 kB, free: 347924 kB
shared: 0 kB, buffers: 1588 kB, cached 0 kB
cf info:
filesystem: /dev/cf
total: 1014624 kB, used: 360960 kB, available: 653664 kB
last boot reason: NP 0 Failed : NP ME Hung
configuration register: 0x1
Could you please advise whether there is any bug in the above software version i.e. it removes the root certs due to heavy transaction load.
Thanks.

I wanted to look for more details regarding this bug id. But I got the below message in Bug Toolkit. Please advise...
CSCsl96203 Bug Details
Information contained within bug ID CSCsl96203 is only available to Cisco employees. It is our policy to make all externally-facing bugs available in Bug Toolkit so the system administrators have been automatically alerted to the problem. By choosing to save this bug, you may be notified when the decision to make this bug available to you has been made. Note: Some product enhancement requests and documentation error bugs may not be available in Bug Toolkit.

ACE Module support loadbalance rmi, ajp, jms, etc?

Hello,
Do you know if ACE Module support balance the follow protocols:
1. rmis
2. ajp
3. jms
4. IIOP
5. CORBA
6. IIOPS
I know that ACE module support http, https and tcp/udp port.
Best Regards

Hi Alvaro,
There are no specific handlers in ACE for the protocols listed. RMI over IIOP and majority of CORBA implementations are TCP socket based and typically require persistent (Sticky) assignments to real servers if load-balanced, so generic ACE loadbalancing predictors, probes and sticky features should suffice. If you need to do a deeper inspection you can use the Generic Protocol Parsing, and custom Probe (TCL) capabilities to track content of interest. Same applies for JMS and AJP, although there are different transports for these prototocls (i.e. JMS over HTTP) which may change configuration requirements.
In general, since these protocols are used for stateful application integration, long running transactions, messaging, and data access...and they are very sensitive to object namespace/target references you should detail individual use case requirements and applicability of external application delivery controller based load balancing (i.e. using ACE).
Let me know if this helps or if you need more detail. Thanks. -George

A problem with ACL in the class-map on the ACE module

Hi all,
I configured the following on the ACE module:
object-group network test
host 192.168.1.21
host 192.168.1.22
host 192.168.1.23
object-group service port
tcp eq www
tcp eq 8080
access-list T line 8 extended permit object-group port object-group test any
I tried to configure a class-map for matching this ACL:
ACE-4710-2/Lab-OPT-11(config)# class-map match-any TEST_C
ACE-4710-2/Lab-OPT-11(config-cmap)# match access-list T
Error: Cannot associate acl having object-group ACEs in class-map.
So couldn't I configure the class-map by using ACL with object-groups involved? Is it the bug or the normal behaviour? Because the customer uses object-groups in ACLs and he has to configure ACL without object-groups for the traffic classification. It is horrible.
Thank you
Roman

Hi Roman,
I'm afraid it's the expected behavior. You cannot use an ACL with object-groups inside a class-map.
Regards
Daniel

How can I show all missing content in iTunes library?

How can I show all missing content (ie. show the exclamation mark against each track)? I can restore the missing content but need to know what is missing without running each track.

One way to identify the broken links in your library is to create this set of playlists:
Lost & Found playlists
Create a playlist called Found, select everything in Music and drag it into the Found playlist. Create a smart playlist called Lost matching All the rules Playlist is Music and Playlist is not Found. Your lost tracks will be in this playlist.
Or use iTunes Folder Watch and enable its option to check for dead tracks on startup.
tt2

I transfered my iTunes library from 1 computer to another and am now missing content. How do I get it back?

I transfered my iTunes library from my old computer to my new computer using iCloud and an missing content. My iPhone still has my full library on it. I've synced my phone but the missing cntent wont transfer over. How do I get my complete library on my new computer? My old computer had windows 7; the new one windows 8. Dont know if this makes any difference.

Delete the garbage that has been created on the new computer.
Copy the ENTIRE iTunes folder from the old computer to the new computer. Launch iTunes, everything will now be as it was on the old computer.

How to Virtual IP configuration in ACE module?

Hi,
I am in the process of configuring load balancing on ACE module but struggling to configure virtual IP address for ACE module.
I'm working on ACE30 module and using software version A5 (1.2). ACE module is in slot of Catalyst 6504 switch.
Can anybody please post the steps/commands to perform this activity? An early response would be appreciated.
Regards,
Rachit.

Hi Rachit,
Here is a basic configuration example:
access-list Allow_Access line 10 extended permit ip any any
rserver host test
ip address 10.198.16.98
inservice
rserver host test2
ip address 10.198.16.93
inservice
serverfarm host test
rserver test 80
    inservice
rserver test2 80
    inservice
sticky http-cookie test group2
cookie insert
serverfarm test
class-map match-all VIP
2 match virtual-address 10.198.16.122 tcp eq www
policy-map type loadbalance first-match test
class class-default
    sticky-serverfarm group1
policy-map multi-match clients
class VIP
    loadbalance vip inservice
    loadbalance policy test
    loadbalance vip icmp-reply active
    nat dynamic 1 vlan 112
interface vlan 112
ip address 10.198.16.91 255.255.255.192
access-group input Allow_Access
nat-pool 1 10.198.16.122 10.198.16.122 netmask 255.255.255.192 pat
service-policy input NSS_MGMT
service-policy input clients
no shutdown
ip route 0.0.0.0 0.0.0.0 10.198.16.65
Here is the configuration guide:
http://tools.cisco.com/squish/101AD
Cesar R

Still missing content after 9.1.6 "upgrade" and content re-installs

I updated to 9.1.6 and immediately I noticed that various .aif files were missing, from my ESX24 instruments and Garageband loops.
After reading other peoples' similar stories and solutions here, I spent some hours (and probably $$ for all the bandwidth) downloading and re-installing "Garageband content" (which showed needed updating) as well as the "Essential" and "Additional" Logic content packages (which were supposedly already installed).
After downloading about 7GB of stuff, I am still missing content, .aif files which are part of ESX24 instruments and Garageband loops.
I guess I'll continue downloading and re-installing the rest of the Jam Pack content -- about another 10GB -- and hope that I get that stuff back. No guarantees though, I suppose.
Apple, this happened to me once before, when I upgraded from Logic Studio 8 to 9. It's really, really maddening.

You'll need to either manually copy over the old content, or download the media packs after you install the 9.0 version. In the Application menu, select "Download additional content...". However, do NOT click the "Select All Uninstalled" and instead download each part separately. A bit of added work, but selecting "Select all uninstalled"is giving people fits in that you end up with a lot of "Download Failed" messages and nothing installs.
HTH,
Tim

SOAPException: faultCode=SOAP-ENV:Protocol; msg=Missing content type

I have a WSDL file for which I have created a Web Service stub/skeleton through jdeveloper(version 10.1.2.3.0). Below is the complete code which has been generated by developer. Now whenever i try to run this file in jdeveloper I get the following exception. Please let me know how to resolve this issue.
Also error message is received at the following line of code:
*msg.send(endpointURL, ""<<some URL>>", requestEnv);*
{code}
*Exception Message*
{code}
[SOAPException: faultCode=SOAP-ENV:Protocol; msg=Missing content type.]
at org.apache.soap.transport.TransportMessage.read(TransportMessage.java:249)
at oracle.soap.transport.http.OracleSOAPHTTPConnection.post(OracleSOAPHTTPConnection.java:973)
at oracle.soap.transport.http.OracleSOAPHTTPConnection.send(OracleSOAPHTTPConnection.java:722)
at org.apache.soap.messaging.Message.send(Message.java:125)
at mypackage.NPVNSDLStub.PANDetails(NPVNSDLStub.java:88)
at mypackage.NPVNSDLStub.main(NPVNSDLStub.java:41)
{code}
*Code generated by Jdeveloper*
{code}
package mypackage;
import oracle.soap.transport.http.OracleSOAPHTTPConnection;
import org.apache.soap.encoding.SOAPMappingRegistry;
import org.w3c.dom.Element;
import java.util.Vector;
import oracle.jdeveloper.webservices.runtime.WrappedDocLiteralStub;
import java.net.URL;
import org.apache.soap.Envelope;
import org.apache.soap.Body;
import org.apache.soap.messaging.Message;
import java.util.Properties;
* Generated by the Oracle JDeveloper 10g Web Services Stub/Skeleton Generator.
* Date Created: Wed Feb 29 18:39:33 IST 2012
* WSDL URL: file:/C:/WS/sample.wsdl
public class NPVNSDLStub extends WrappedDocLiteralStub
public NPVNSDLStub()
m_httpConnection = new OracleSOAPHTTPConnection();
public static void main(String[] args)
try
NPVNSDLStub stub = new NPVNSDLStub();
stub.PANDetails("aaaaa8888a");
catch(Exception ex)
ex.printStackTrace();
private String _endpoint = "<<some URL>>";
public String getEndpoint()
return _endpoint;
public void setEndpoint(String endpoint)
_endpoint = endpoint;
private OracleSOAPHTTPConnection m_httpConnection = null;
private SOAPMappingRegistry m_smr = null;
public String PANDetails(String Request) throws Exception
URL endpointURL = new URL(_endpoint);
Envelope requestEnv = new Envelope();
Body requestBody = new Body();
Vector requestBodyEntries = new Vector();
String wrappingName = "PANValidationRequest";
String targetNamespace = "<<namespace url>>";
Vector requestData = new Vector();
requestData.add(new Object[] {"Request", Request});
requestBodyEntries.addElement(toElement(wrappingName, targetNamespace, requestData, false));
requestBody.setBodyEntries(requestBodyEntries);
requestEnv.setBody(requestBody);
Message msg = new Message();
msg.setSOAPTransport(m_httpConnection);
*msg.send(endpointURL, "<<some URL>>", requestEnv);*
Envelope responseEnv = msg.receiveEnvelope();
Body responseBody = responseEnv.getBody();
Vector responseData = responseBody.getBodyEntries();
return (String)fromElement((Element)responseData.elementAt(0), java.lang.String.class);
{code}
Edited by: EJP on 2/03/2012 17:22: added code tags, but your indentation needs fixing

Kishore,
See the links referenced in these threads.
Web Services and R12
Re: Web Services and R12
Integrated SOA Gateway
Re: Integrated SOA Gateway
Regards,
Hussein

Load Balancing on ACE Modules

hi,
Is it possible to load balance VIP hits on two ACE Modules in an active/active configuration. Or is it that only per FT group only single context could be active.
Regards.

You can have 1 context active on one ACE and the other context active on the other ACE.
If you have 2 Vip, you can have 1 vip belonging to one context and the other vip belonging to the other context.
Like this, you split the traffic between the 2 devices which allows you to handle more traffic than what 1 device could normally do.
If one device can handle all your traffic, I prefer to only have 1 active unit and 1 standby.
Easier to implement and troubleshoot.
Gilles.

Missing content on ACE module.

Similar Messages

Maybe you are looking for