Mixing T1s and PRIs on th same router
I have a Cisco 2851 voice bundle. Is it possible to take two VWIC 1MFT-T1 modules and use one for a voice PRI and one for a voice T1 line? I think I read that you couldn't do it with a 2MFT-T1 card but wasn't sure about splitting it up but still on the same router.... I also have a data T1 via a 1DSU-T1V2 on the box.
Thank!
Having 2 voice circuits (i.e. 2 T1/PRIs on a VWIC-2MFT-T1 .. is that supported by Cisco? and what about having 1 T1/PRI for Voice and 1 T1 for Data on the same VWIC-2MFT-T1 card. I had a lot of clients running with both scenarios above and some of them are having clocking issues and Telco is saying the circuits are clean. Is that something to do with the internal clocking of the router in order to sync the DSPs?
-Jose
Similar Messages
-
When I share a video with fcpx and it goes to Quicktime, the last few seconds goes mute. I checked the clip and sent that the same route and all is fine. It is only when I send the whole 3gb video. Any ideas?
paul71054 wrote:
... Any ideas?
add a few seconds black to your project.
Try again.
could be some really weird codec problem, with 'cut' GOPs', .. somethin'... -
MGCP and H.323 in same router
We have few 3825 and 3845 routers with VWIC-1MFT-T1, VIC2-2FXS and VIC2-2FXO cards. CCM is 4.1(3)SR1
Checked MGCP & H.323 can support analog FXO interfaces loop-start/ground-start signaling, analog FXS interfaces loop-start/ground-start signaling and T1/E1 ISDN PRI Q.931 interfaces.
http://www.cisco.com/en/US/products/ps5855/products_data_sheet09186a0080182d38.html
Anyone has experience in below configurations? For example,
1. Config only MGCP to support all three above voice modules (T1, FXS, FXO) in a router (would like to confirm)
2. Or config only H.323 to support all modules in a router (should be okay, no issue)
3. Or config MGCP for T1 and H.323 for FXS & FXO in a router (would like to confirm)
4. Or config MGCP for T1 in one router and config H.323 for FXS & FXO in another router (should be okay, no issue)
Thank you in advance.All options are valid. You can have MGCP and H.323 to control seperate ports on the same router. If you go with option 3 (my guess is this is what you want) make sure to point the dial-peers to the appropriate ports.
HTH,
Chris -
Mix overview and detail records in same report
Hello, in substance I need to mix results from overview table and records from details table in same report.
For creating the scenario:
CREATE TABLE ALPHA
ALPHA_ID NUMBER,
ALPHA_NR NUMBER,
ALPHA_TOTCT NUMBER,
ALPHA_FUND NUMBER
ALTER TABLE ALPHA ADD (
CONSTRAINT ALPHA_PK PRIMARY KEY (ALPHA_ID));
ALTER TABLE ALPHA ADD (
CONSTRAINT ALPHA_NR_UNI UNIQUE (ALPHA_NR));
INSERT INTO ALPHA(ALPHA_ID, ALPHA_NR)
VALUES( 1, 7 );
INSERT INTO ALPHA(ALPHA_ID, ALPHA_NR)
VALUES( 2, 11 );
INSERT INTO ALPHA(ALPHA_ID, ALPHA_NR)
VALUES( 3, 15 );
INSERT INTO ALPHA(ALPHA_ID, ALPHA_NR)
VALUES( 4, 17 );
CREATE TABLE HIST
HIST_ID NUMBER,
HIST_NR NUMBER,
HIST_ALPHA_NR NUMBER,
HIST_CT NUMBER,
HIST_VAL NUMBER,
HIST_DATE DATE
ALTER TABLE HIST ADD (
CONSTRAINT HIST_PK PRIMARY KEY (HIST_ID));
ALTER TABLE HIST ADD (
CONSTRAINT HIST_NR_UNI UNIQUE (HIST_NR));
ALTER TABLE HIST ADD (
CONSTRAINT HIST_ALPHA_NR_FK FOREIGN KEY (HIST_ALPHA_NR) REFERENCES ALPHA ( ALPHA_NR ) );
TRUNCATE TABLE HIST;
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 1 ,1 ,7 ,1 ,10 , TO_DATE('01.02.2009' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 2 ,6 ,7 ,1 ,10 , TO_DATE('01.05.2009' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 3 ,3 ,7 ,3 ,30 , TO_DATE('01.02.2010' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 4 ,4 ,11 ,1 ,10 , TO_DATE('01.03.2009' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 5 ,5 ,11 ,-2 ,-20 , TO_DATE('01.06.2010' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 6 ,8 ,11 ,1 ,10 , TO_DATE('01.02.2011' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 7 ,2 ,15 ,2 ,20 , TO_DATE('01.03.2009' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 8 ,7 ,15 ,5 ,50 , TO_DATE('01.06.2010' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 9 ,9 ,15 ,-4 ,-40 , TO_DATE('01.02.2011' , 'dd.mm.yyyy' ) );
INSERT INTO HIST( HIST_ID ,HIST_NR ,HIST_ALPHA_NR ,HIST_CT ,HIST_VAL ,HIST_DATE )
VALUES ( 10 ,10 ,17 ,1 ,10 , TO_DATE('01.03.2011' , 'dd.mm.yyyy' ) );For updating the overview table, I used a view
CREATE OR REPLACE VIEW HIST_AGG ( HIST_ALPHA_NR, TOT_CT , TOT_VAL )
AS
SELECT HIST_ALPHA_NR
,SUM ( NVL(HIST_CT, 0 ) ) TOT_CT
,SUM( NVL(HIST_VAL, 0) ) TOT_VAL
FROM HIST
GROUP BY HIST_ALPHA_NR;
DECLARE
CURSOR cur
IS
SELECT
HIST_ALPHA_NR
,TOT_CT
,TOT_VAL
FROM HIST_AGG
BEGIN
FOR rec IN cur
LOOP
UPDATE ALPHA
SET ALPHA_TOTCT = rec.TOT_CT
, ALPHA_FUND = rec.TOT_VAL
WHERE ALPHA_NR = rec.HIST_ALPHA_NR;
END LOOP;
END;First report should the overview line from table alpha followed by all detail records from
table HIST, and this for each alpha_nr. At the end of the report a total from the overview
table alpha.
"SUMMARY";"ALPHA_NR";"ALPHA_TOTCT";"ALPHA_FUND";
;7;5;50;
;7;1;10;01.02.2009
;7;1;10;01.05.2009
;7;3;30;
;11;0;0;
;11;1;10;01.03.2009
;11;-2;-20;01.06.2010
;11;1;10;01.02.2011
;15;3;30;
;15;2;20;01.03.2009
;15;5;50;01.06.2010
;15;-4;-40;01.02.2011
;17;1;10;
;17;1;10;01.03.2011
"TOTAL_ALPHA_NR";4;9;90;Second report should display the overview per time period (year), but the records from
e.g. year 2009 start counting in year 2010. At the end of each year again a summary for
the actual status.
"YEAR";"ALPHA_NR";"ALPHA_TOTCT";"ALPHA_FUND"
2009;7;0;0
;11;0;0
;15;0;0
;17;0;0
"Total 2009";4;0;0
2010;7;2;20
;11;1;10
;15;2;20
;17;0;0
"Total 2010";4;5;50
2011;7;5;50
;11;-1;-10
;15;7;70
;17;0;0
"Total 2011";4;11;110
2012;7;5;50
;11;0;0
;15;3;30
;17;1;10
"Total 2012";4;9;90Hi,
This is quite a different problem from what you first posted.
wucis wrote:
This is what I want to get
ALPHA_DATE ALPHA_NAME ALPHA_NR ALPHA_TOTCT ALPHA_FUND TRANS_DATE
01.01.2009 seven 7 5 50
7 1 10 01.02.2009
7 1 10 01.05.2009
7 3 30 01.02.2010
01.03.2009 eleven 11 0 0
11 1 10 01.03.2009
11 -2 -20 01.06.2010
11 1 10 01.02.2011
03.05.2010 twelve 12 0 0
02.02.2009 fifteen 15 3 30
15 2 20 01.03.2009
15 5 50 01.06.2010
15 -4 -40 01.02.2011
10.10.2010 seventeen 17 1 10
17 1 10 01.03.2011
TOTAL_ALPHA_NR 5 9 90
Do you really want to include alphr_nr=12? If so, what do you mean when you say
I have an approach but there are "unnecessary" rows ( the line with just alpha_nr = 12 ) and why don't you want alpha_nr=13?
so my join is buggyExactly! The join
... from hist, alpha b
WHERE b.alpha_nr = hist.hist_alpha_nr (+) ...means "include all rows from alpha, whether of not they have any corresponding rows in hist or not". If you want to exclude alpha_nrs 12 and 13, you probably want to do an inner join there.
You don't need any sub-queries to do that:
SELECT CASE
WHEN GROUPING (h.hist_alpha_nr) = 0
AND GROUPING (h.hist_date) = 1
THEN MAX (a.alpha_date)
END AS alpha_date
, CASE
WHEN GROUPING (h.hist_alpha_nr) = 1
THEN 'TOTAL_ALPHA_NR'
WHEN GROUPING (h.hist_date) = 1
THEN MAX (a.alpha_name)
END AS alpha_name
, CASE
WHEN GROUPING (h.hist_alpha_nr) = 0
THEN h.hist_alpha_nr
ELSE COUNT (DISTINCT (alpha_nr))
END AS alpha_nr
, SUM (h.hist_ct) AS alpha_totct
, SUM (h.hist_val) AS alpha_fund
, h.hist_date AS trans_date
FROM hist h
, alpha a
WHERE h.hist_alpha_nr = a.alpha_nr
AND a.active = 'Y'
GROUP BY ROLLUP ( hist_alpha_nr
, hist_date
ORDER BY GROUPING (h.hist_alpha_nr)
, h.hist_alpha_nr
, GROUPING (h.hist_date) DESC
, h.hist_date
;Output:
ALPHA ALPHA ALPHA
ALPHA_DATE ALPHA_NAME _NR _TOTCT _FUND TRANS_DATE
01.01.2009 seven 7 5 50
7 1 10 01.02.2009
7 1 10 01.05.2009
7 3 30 01.02.2010
01.03.2009 eleven 11 0 0
11 1 10 01.03.2009
11 -2 -20 01.06.2010
11 1 10 01.02.2011
02.02.2009 fifteen 15 3 30
15 2 20 01.03.2009
15 5 50 01.06.2010
15 -4 -40 01.02.2011
10.10.2010 seventeen 17 1 10
17 1 10 01.03.2011
TOTAL_ALPHA_NR 4 9 90If this is not what you want (e.g., if you want alpha_nr=12 in the results) then point out where these results are wrong, post the correct results, and explain how you get the correct results in those places. -
EAZYVPN and DMVPN on the same router,same interface
Hi all,
First of all, thanks in advance for the help. I have setup DMVPN and EAZYVPN on one router. Tunnel interface on Spoke one and Spoke two are up/up and show crypto ISakmp sa shows both tunnels are in idle. However, tunnel to Spoke one(10.10.1.1) keep bouncing on and off(see below). Every 30 sec or so, the tunnel gone back to IKE phase while tunnel for spoke two(5.5.5.1) still leave active. THe configuration on the HUB side is the same for both spoke!! show crypto ipsec sec shows both side has the same life time(IOS default). Could that be an IOS debug on the spoke one?
Hub :
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 15.1(3)T2, RELEASE SOFTWARE (fc1)
HUB#sh crypto ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
Spoke one:
Cisco IOS Software, C2600 Software (C2600-ADVSECURITYK9-M), Version 12.4(8), RELEASE SOFTWARE (fc1)
SPOKE1#sh crypto ipsec security-association
Security association lifetime: 4608000 kilobytes/3600 seconds
HUB#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
5.5.5.1 5.5.5.2 QM_IDLE 1002 ACTIVE
10.10.1.1 10.10.1.2 MM_NO_STATE 1134 ACTIVE (deleted)
10.10.1.1 1.1.1.10 QM_IDLE 1126 ACTIVE
10.10.1.1 1.1.1.10 QM_IDLE 1076 ACTIVE
HUB#sh crypto se
HUB#sh crypto session
Crypto session current status
Interface: Serial0/1/1
Username: testuser
Profile: AccountingPro
Group: Accounting
Assigned address: 20.20.20.1
Session status: UP-ACTIVE
Peer: 1.1.1.10 port 60201
IKEv1 SA: local 10.10.1.1/500 remote 1.1.1.10/60201 Active
IPSEC FLOW: permit ip 0.0.0.0/0.0.0.0 host 20.20.20.1
Active SAs: 2, origin: dynamic crypto map
Interface: Serial0/1/1
Username: testuser
Profile: AccountingPro
Group: Accounting
Assigned address: 20.20.20.2
Session status: UP-ACTIVE
Peer: 1.1.1.10 port 49768
IKEv1 SA: local 10.10.1.1/500 remote 1.1.1.10/49768 Active
IPSEC FLOW: permit ip 0.0.0.0/0.0.0.0 host 20.20.20.2
Active SAs: 2, origin: dynamic crypto map
Interface: FastEthernet0/1
Profile: DMVPN
Session status: UP-IDLE
Peer: 5.5.5.2 port 500
IKEv1 SA: local 5.5.5.1/500 remote 5.5.5.2/500 Active
Interface: Serial0/1/1
Profile: DMVPN
Session status: DOWN-NEGOTIATING
Peer: 10.10.1.2 port 500
IKEv1 SA: local 10.10.1.1/500 remote 10.10.1.2/500 Inactive
HUB#
2. My second issue is, I use the same interface(s0/1/1=10.10.1.1) for eazyvpn access. The client from eazyvpn is connected fine,but does not receive traffric back(statics window show no decrypted=0 and reeiced=0). The eazy vpn can't even ping the IP address assigned to the vpn client(20.20.20.2), and the client can only pin 10.10.1.1 address. Reverse router is able but the 20.20.20.0/24 network didn't show up in the ip table of the HUB router!!!
DMVPN AND EAZYVPN SERVER config..
crypto keyring dmvpnkey
pre-shared-key address 0.0.0.0 0.0.0.0 key DMVPNLAB
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp policy 20
encr aes
authentication pre-share
group 2
crypto isakmp policy 30
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 40
authentication pre-share
crypto isakmp keepalive 30
crypto isakmp xauth timeout 90
crypto isakmp client configuration group Accounting
key eazypvn
dns 4.2.2.2
wins 4.2.2.2
domain bigBois.com
pool dmAccouting
crypto isakmp profile AccountingPro
match identity group Accounting
client authentication list access_in
isakmp authorization list my_vpn
client configuration address respond
crypto isakmp profile DMVPN
keyring dmvpnkey
match identity address 0.0.0.0
crypto ipsec transform-set DMVPN ah-sha-hmac esp-aes
mode transport
crypto ipsec transform-set EAZYVPN esp-3des esp-md5-hmac
crypto ipsec profile dmvpnlab
set transform-set DMVPN
set isakmp-profile AccountingPro
crypto dynamic-map Remote_Acc 20
set transform-set EAZYVPN
set isakmp-profile AccountingPro
reverse-route
crypto map RemoteAcc client authentication list access_in
crypto map Remote_Acc client authentication list my_vpn
crypto map Remote_Acc 20 ipsec-isakmp dynamic Remote_Acc
interface Loopback0
ip address 192.168.200.1 255.255.255.0
interface Loopback2
ip address 172.16.10.1 255.255.255.0
interface Loopback3
ip address 172.16.15.1 255.255.255.0
interface Tunnel1
bandwidth 10000
ip address 4.4.4.1 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 10
ip nhrp authentication DMVPN
ip nhrp map multicast dynamic
ip nhrp network-id 7940
ip nhrp registration timeout 10
ip tcp adjust-mss 1360
tunnel source Serial0/1/1
tunnel mode gre multipoint
tunnel key 7940
tunnel protection ipsec profile dmvpnlab
interface FastEthernet0/0
description OUTSIDE
ip address 1.1.1.1 255.255.255.0
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
description INSIDE
ip address 5.5.5.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface Serial0/1/0
no ip address
shutdown
clock rate 2000000
interface Serial0/1/1
description to SPOKE1
ip address 10.10.1.1 255.255.255.0
crypto map Remote_Acc
interface Serial0/3/0
no ip address
shutdown
router eigrp 10
network 4.4.4.0 0.0.0.255
network 5.5.5.0 0.0.0.255
network 10.0.0.0
network 10.10.10.0 0.0.0.3
network 172.16.0.0 0.0.0.255
network 172.16.1.0 0.0.0.255
network 172.16.10.0 0.0.0.255
network 172.16.15.0 0.0.0.255
network 192.168.200.0
ip local pool dmAccouting 20.20.20.1 20.20.20.10
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
THanks a bunch for the help,
ErnestAny ideas why devices keep renewing phase 1?
Thanks, -
Can you mix DV and HDV in the same sequence?
Hi Everyone....
I am new to the forum, and new to FCP...yes! I joined the dark side and just got a MAC.
I am trying to learn this system, and the 500 manuals it came with are about as clear as mud.....
Can I mix 16x9 DV footage with 16x9 HDV footage? And please don't tell me I am hosed!
I have some footage right now in a sequence, but it has the red line above the sequence, indicating that it needs to render.
And actually I can't even get the high def footage alone in a sequence to work...but that is another post.
Thanks in advance...
Aubry
Mac Pro Quad Xion Mac OS X (10.4.7) 2.66 GHz | 4GB ram | NVIDIA GeForce 7300 GT | 1 250G &1 500G Internal DrivesI think what your asking is this....the captured clip is:
frame size: 1440x10180
compressor: hdv 1080i60
data rate 3.2 mb
pixel aspect: hd 1440/1080
I changed the sequence settings to match this and it came out all kinds of funky.
Is there another way to find out what kind of high def the clip is? I have the Sony FX1 if that matters.... -
Mix AVG and Total for the same column in ALV grid
Hi,
We are using CL_GUI_ALV_GRID=>SET_TABLE_FOR_FIRST_DISPLAY, and I'd like to know if the following situation is possible.
Let's say we have a column which contains a number of hours, and we set it up to subtotal by period, but as an average rather than a total (DO_SUM = "C"). This is not a problem so far.
The problem is that we'd like for the "Grand Total" at the bottom of the ALV grid to total all of the subtotal averages, instead of calculating an average.
Ex:
Period Hours
2010/01 6.0
2010/02 7.0
2010/03 2.0
5.0 (This is an average... 6.0 + 7.0 + 2.0 / 3)
2011/01 12.0
2011/02 5.0
2011/03 4.0
7.0 (This is an average... 12.0 + 5.0 + 4.0 / 3)
12.0 (We want this to be a total of 5.0 + 7.0)
So we want the "grand total" line to be 12.0 which is the sum, but it currently comes out as an average.
Therefore we're looking to average at the sub total level, but we want a total of the subtotal levels at the grand total level for the same column.
Thanks,
DenisRefer to the suggestion given by Naimesh here Can we modify a sub-total in ALV making use of function GET_GLOBALS_FROM_SLVC_FULLSCR and the method GET_SUBTOTALS. You can see the parameter ep_collect01 refered in case of subtotals. Can you please check ep_collect00 for grand total in your case.
As said about EP_COLLECT00,here goes a classic example Modify grand total in ALV GRID
BR
Keshav
Edited by: Keshav.T on Sep 21, 2011 9:39 AM -
Mix formCalc and javascript in same event?
Hi Folks,
I have a bunch of formCalc and Javasript I'm trying to merge (two different forms, different programmers). Is it possible to mix javascript with formCalc in the same field event? If so, how?
thanks!No, it is not possible to mix FormCalc and JavaScript in the same event. You will get run-time errors.
Steve -
Using Crypto Maps and IPsec Static VTI's on the same router
Is it possible to configure both crypto maps and IPsec static VTI's on the same router? What platforms have this capability? What IOS version do I need?
Yes you can and as far as I know I dont think there is a hardware dependency.
VTI mode 'tunnel mode ipsec ipv4' was added in 12.3(14)T.
If you are mixing tunnel protection and crypto map ensure you use iskmp profiles to differentiate somehow that the tunnel IPSec connection is not prcessed on the crypto map!
Here is a rough example (fine tune it as needed):
crypto keyring key1
pre-shared-key address 1.1.1.1 key test123
crypto keyring key2
pre-shared-key address 7.7.7.7 key test777
crypto isakmp profile vpn1
keyring key1
match identity address 1.1.1.1 255.255.255.255
crypto isakmp profile vpn2
keyring key2
match identity address 7.7.7.7 255.255.255.255
crypto ipsec transform-set test esp-des esp-sha-hmac
crypto IPsec profile vpn-tunnel
set transform-set test
set isakmp-profile vpn1
crypto map mymap 1 ipsec-isakmp
set transform-set test
set peer 7.7.7.7
set isakmp-profile vpn2
match address 177
interface Tunnel0
ip address 10.0.51.217 255.255.255.0
tunnel source 2.2.2.2
tunnel destination 1.1.1.1
tunnel mode ipsec ipv4
tunnel protection ipsec profile vpn-tunnel
interface Ethernet4
ip add 2.2.2.2 255.255.255.0
crypto map mymap
Regards,
Uwe -
I all,
the scenario is the following:
WIFI connection with TISCALI operator. Encryption made by WPA2 EAS with router SITECOM or tested also with another router DIGICOM with WPA TPK.
From December up to end of March the IPAD2 working perfectly serfing and downloading.
By two weeks it has a very strange behavour without have changed any configuration on IPAD or network:
with WIFI turned on it discover about 4 different ntw among them the mine, I successfully authenticate with psw the my ntw,
the IPAD2 start to run with Safari without problems, but after about 1 minutes, it stop to serf or download and answer that the Server cannot be reached or the page cannot be open, at the same time the signal is present on the icon of WIFI and it is strong.
This problem is systematic: If I dissasociate the ntw and then authenticate again I start to serf again for 1 minutes (more or less) and then it stops again, this occurs every time I authenticate the ntw after a disassociation.
I made some test changing the encryption from WPA2, WPA and also without encryption but the result was always the same, after about one minute the server seems to be for the IPAD2 no more reachable while the others PC and netbook connected to the same router continue to serf/download without problems!
I also tried to change the router with a DIGCOM that I did not use generally, but the behavour is always the same.
Since the IOS was the 4.3 revisin, I made the upgrade by means Itunes to IOS 5.1 succesfully installed.
But unfortunatelly all test repeted have had the same negative result with the same behavour!
Yesterday I tried to do the complete restore of the System but the tests had the same rsult.
I really don't know how to proceed, the problem started suddenly without any action from my side....is there someone that can help me?
Thanks MassimoLook at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Cheers, Tom -
My wife and I share the same email address but have separate IPhones. We would like to have each phone individually on "find friends" but cannot do it via email route. How is it done?
make seperate appleID's if you wish to be frinds or if you wish to facetime video chat and if you wish to not recieve the samme imessage msg's unless you turn it off
you can still set both your iphones to use an email address even if both have different appleId's
the appleID is a handle not a link to an email address -
Home Sharing is not working between wireless PC's / devices and ethernet wired PC's on the same router. I installed a new Verizon FIOS ActionTec MI424WR GigE wireless / ethernet router, replacing the original FIOS router. With the old router Home Sharing worked fine across and among all iOS and Windows wired and wireless devices. With the new router Home Sharing works between and among the Wired PC's but not between the wired PC's and the Wireless connected PC's or iOS devices. Home Sharing also works between and among the wireless connected PC's and iOS decices but not between them and the wired PC's.
Only the router was changed. No changes were made to any of the devices except all were updated with the latest version of iTunes 10.7.0.21 and the iSO devices were updated to iOS vrsion 6.01. Three PC's are wired and all are running Windows 7. There also is a Windows Home Server connected to the router by ethernet port. It does not run iTunes but does provide WebDAV services to my iOS devices. This works fine. Two PC's are wireless, one running Windows 7 and one running Windows 8. All of the PC's are connected to the same (new) router via it's ethernet ports and it's wireless access point. Two of the wired PC's are connected via a high-speed ethernet hup that is connected to the router (Home Sharing works fine between the two PC's on the hub and the PC on the router). All wired and wireless devices on the router are visible and members of the router's Home/Office virtual network.
All of the PC's are visible in the Windows network and all shared files are accessable from all PC's, both wired and wireless.
Obviously the router seems to be the issue, something between the ethernet and the wireless access point components. I checked the settings and found nothing that would prevent Home Sharing between the wired and wireless devices. There is no setting that isolates the wireless network. I have done the following:
Read the router user manual and checked all the settings
Rebooted the router and tested.
Turned off the router's firewall and tested.
Home Sharing is turned on all the devices and all use the same Apple ID.
Restarted iTunes and tested.
Verified iTunes is "Allowed" in each PC's firewall.
Again, I can Home Share between the two wireless PC's but not between either of the wireless PC's and any of the wired PC's. I can Home Share between my iPads and iPhones and either of the two wireless PC's but not with any of the wired PC's. I can Home Share between any of the wired PC's but not between any wired PC and a wireless PC or iOS device.
I hope someone may have had a similar problem and has a fix suggestion. I'm stumped! I have a;so contacked ActionTec and awaiting an answer.Solution from ActionTec is:
Log into your router.
Click the Advanced icon
Cclick Yes
Click on the IGMP Proxy
Select Disable
Click Apply -
I think I have tried everything I could find/think of to get this to work. I can connect it to my stereo and stream music fine but the internet won't work. I really just want it to join/or extend so that my internet connection remains intact and I can stream music and surf the web at the same time.
Any help would be appreciated!
ThanksYou would probably want your Express to join the network if an extender isn't required. Reset to factory settings and join the network.
If you do want your Express as an extender run an Ethernet cable between the Express and the Verizon router and set the Express up to be in bridge mode, with the same WiFi network name and password as your Verizon router. -
Mixing public and private networks on the same switch
Hello Everyone,
I know this may get some security engineers in frenzy but wanted to know if there is a safe way to mix public and private networks on the same switch.
We have many remote offices that we want to add public wifi and a couple of other services that would be completely outside of our internal network. Each office has a 3750 with plenty of open ports. How can I safely create a vlan for public access on these switches which currently have our internal network on. I have read that people are doing this to save on the cost of purchasing a dedicated switch. Some people are using access lists and one person mentioned creating a private vlan for the public network. I looked up private vlan and it seemed bit confusing.
Is this recommended? If not what would be the safest way to do this?
Thanks EveryoneDisclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
How "safe" is relative. If your running just one VLAN on a switch, that's would be the safest (basically the same as mixing traffic on the same wire - separation is done else where).
If you multiple VLANs on a switch, then you need to determine how likely someone might figure out a way to breach the VLAN barriers. (This isn't so easy on newer switches.) If the VLAN isolation is breeched, then you need to examine what does that imply from a security perspective (for example can someone now inject or receive other VLAN traffic).
For most purposes, I don't see mixing public and private VLANs, alone, on the same switch as much of a risk. More of a concern is what can be reached on either VLAN and how well it's protected. -
can I have the ipad2 on wifi and the AppleTV on a wired port of the same router in order to use airplay?
I belive you can, I think my friends Apple TV is connected to their internet via an Ethernet cable, and we use Airplay sometimes using our iPads that are connected to the same network via WiFi. It should work as long as they are both connected to the same network. However, I don't have an Apple TV of my own, so don't take this as a solid answer.
Maybe you are looking for
-
My app store will not open on my mac
my app store will not load on my mac
-
Action Script remove EXIF data
hey Hey Hey! How can i get my photoshop to erase all the exif data associated with a file? And also prevent photoshop from saving to "Photoshop CS6" to the "program name" exif data included that i want to be removed is shutter speed, GPRS location, l
-
Hi, I've downloaded a free 30-day trial version of Adobe Acrobat Pro. It seems like I can't use many options there. For example, I need to delete pages, but under "Pages" in "Manipulate Pages" the option to delete doesn't work. I am clicking on it an
-
dear my iphone 4 made of canada ragor it is locked now how i can contact ragor to unlock my iphone
-
Apple TV3 not find wifi connection
Apple TV3 only works on Ethernet cable not find wifi ? If I connect the ethernet cable finds wifi connecting when the ethernet cable disconnecting from apple tv not find Wifi.