MMO3 high level view

Hello Experts,
I have a need to view a large number of material views for assigned inspection types in MM03...  It is very labor intensive to view hundreds of material numbers one screen at a time to see inspection types assigned and activated.
Question: How can I view many material numbers to see inspection types assigned and activated in a list or table?
Much appreciated.
Verroz

One of the way is
QA08-->enter plant ->select deactivate inspection type>here enter the inspection type which you want to see ( attached to "which" materials)->execute--
>The list you get is "The materials for which that Inspection type is active "
and other is
QMAT table .Crewate querry in SQVI & use table QMAT .

Similar Messages

  • High-level view of steps for 10g OWB-OLAP to Discoverer

    I would greatly appreciate ANY feedback to the following steps. These are not necessarily correct or the best way to do this. I am attempting to take source data, use OWB, create the analytical workspace, and from there have the metadata available and used by Discoverer.
    This is rather high-level, feel free to jump in anywhere.
    We are trying to see if we can get away with NOT using the Analytical workspace manager (AWM) if possible. With that in mind, we are trying to make the most of the process with OWB & OLAP.
    Is this possible to do without ever using the AWM? Can we go end to end (source data--->discoverer final reporting) primarily using OWB to get to the point where we can use the metadata for Discoverer?
    Can anyone relate experiences perhaps that would make me want to consider using the AWM at certain points instead?
    Most importantly, if I do use this methodology, would I be safe after everything has been setup? WOuld I want to consider using AWM at a later point for performance reasons while I am using Discoverer? Or would OWB be helpful as well in some aspects in maintenance of data? Any clue on how often I might need to rebuild, and if so, what to use in that case to minimize time?
    Thanks so much for any insight or opinion on anything I have mentioned!

    Hi Gregory,
    I guess the answer is that this depends. My first question is whether you are looking at a Relational OLAP or Multi Dimensional OLAP solution? This may change the discussion slightly, but just lets look at some thoughts:
    In essence you can use the OWB bridge to generate the AW objects (cubes etc). If you do that (for either ROLAP or MOLAP) you will get the AW objects enabled for querying, using any OLAPI query tool, like BI Beans or the new Discoverer for OLAP. The current OWB release does not run the discoverer enabler (creating views specifically written for EUL support in Disco classic).
    So if you are looking at Disco classic you must use the AWM route...
    The other things that you must be aware off is that the OWB technology is limited to cloning the relational objects for now. This means that you will create a new model based on your existing data. If you want to tweak the objects generated you will probably need to go to the underlying code in either scenario.
    So if you want to create calculated measures for example you could generate a cube with OWB, create a "dummy measure" and add the formula in OLAP DML. The same will go for some other objects you may want to create such as text measures...
    The benefit of creating place holder or dummy measures is that the metadata is completely in order, you simply change the measure's behavior...
    For the future (the beta starts relatively soon) OWB will support much more modeling, like logical cubes and you can then directly deploy to OLAP. Also the mappings are transparent to the storage. So you map to a logical cube and OWB will implement the correct to load either OLAP or relational targets.
    We will also start supporting calculated measures, sparsity definitions, partioning and compression on cubes, as we will support parallel building of cubes.
    Hope this gives you some insight!
    Jean-Pierre

  • Need an outliner - high level view...

    Does InDesign have anything like an outliner? I'm looking for the ability to view (and possibly) rearrange large blocks of text. What I'm looking for is sort of like a TOC, but I'd like to not have to regenerate a TOC every time I need to see how my organization of the information has changed. I know that Story Editor does a little of this, but it also puts in all the body text, and I just need to see the headings.
    I know a little bit about XML and InDesign, but I've never practically used it, so I'm not sure if that would do the trick. My understanding is that XML structured is applied spearately from ID paragraphs tags, and can be applied indepently of formatting. Is this correct?
    Thanks.

    Hi Gregory,
    I guess the answer is that this depends. My first question is whether you are looking at a Relational OLAP or Multi Dimensional OLAP solution? This may change the discussion slightly, but just lets look at some thoughts:
    In essence you can use the OWB bridge to generate the AW objects (cubes etc). If you do that (for either ROLAP or MOLAP) you will get the AW objects enabled for querying, using any OLAPI query tool, like BI Beans or the new Discoverer for OLAP. The current OWB release does not run the discoverer enabler (creating views specifically written for EUL support in Disco classic).
    So if you are looking at Disco classic you must use the AWM route...
    The other things that you must be aware off is that the OWB technology is limited to cloning the relational objects for now. This means that you will create a new model based on your existing data. If you want to tweak the objects generated you will probably need to go to the underlying code in either scenario.
    So if you want to create calculated measures for example you could generate a cube with OWB, create a "dummy measure" and add the formula in OLAP DML. The same will go for some other objects you may want to create such as text measures...
    The benefit of creating place holder or dummy measures is that the metadata is completely in order, you simply change the measure's behavior...
    For the future (the beta starts relatively soon) OWB will support much more modeling, like logical cubes and you can then directly deploy to OLAP. Also the mappings are transparent to the storage. So you map to a logical cube and OWB will implement the correct to load either OLAP or relational targets.
    We will also start supporting calculated measures, sparsity definitions, partioning and compression on cubes, as we will support parallel building of cubes.
    Hope this gives you some insight!
    Jean-Pierre

  • Errors in the high-level relational engine. The data source view does not contain a definition for the table or view. The Source property may not have been set.

    Hi All,
    I have a cube in which i'm using the TIME DIM that i created in the warehouse. But now i wanted a new measure in the cube which is Average over time and when i wanted to created the new measure i got a message that no time dim was defined, so i created a
    new time dimension in the SSAS using wizard. But when i tried to process the new time dimension i'm getting the follwoing error message
    "Errors in the high-level relational engine. The data source view does not contain a definition for "SSASTIMEDIM" the table or view. The Source property may not have been set."
    Can anyone please tell me why i cannot create a new measure average over the time using my time dimension? Also what am i doing wrong with the SSASTIMEDIM, that i'm getting the error.
    Thanks

    Hi PMunshi,
    According to your description, you get the above error when processing the time dimension. Right?
    In this scenario, since you have updated the DSV, it should have no problem on the table existence. One possibility is that table has been specified for tracking in the notifications for proactive caching, but isn't available any more for some
    reason. Please change the setting in Proactive Caching into "MOLAP".
    Reference:
    How To Implement Proactive Caching in SQL Server Analysis Services SSAS
    If you have any question, please feel free to ask.
    Best Regards,
    Simon Hou
    TechNet Community Support

  • Phase out settings at a higher level such as brand or major customer

    Have any of you ever setup phase out assignments at a higher level than product and had it work correctly?  For example, we want to phase out a brand for a major customer.  In other words, a customer is dropping a brand and we don't want statistical forecast generated for that brand customer combination any longer.  I am able to setup the fields in phase out lifecycle settings for product, brand, major account but when i enter the brand and major account I am still getting forecast generated.  It appears to stop for some products within the brand but not all.  Another example is if a customer quits ordering from us I want to setup the major customer to phase out so no forecast is generated.
    If you have done this successfully please let me know.  Or if you would handle these situations in a different manner other than phase out please let me know.  We can do historical adjustments each period but that is a lot of maintenance to do after each period before statistical forecast is generated.
    Thanks
    Steve

    Hi Stephen,
    Life cycle planning works only at the detail level (each CVC), the option of aggregate planning is helpful if you want to phase in or out a certain CVC when you are forecasting at the aggregate level.
    One option is that you should have all products in the "profile assignment for life cycle " section which falls under that brand and customer. you can maintain a file and then automate the upload process in to the "assignment"
    or
    you can try to use the copy functionality in the realignment (/SAPAPO/RLGCOPY) , where you maintain copy factor as NIL and when the stat fcst is generated, you can use this as the next step to zero out -but you would need to maintain them manually.
    or
    easiest and safest wayy would be create a selection for those combination and do not include them in the planning job for stat fcst.
    or
    you can build a customised program to access the PA, PB, Data view and input the selection to zero out the stat fcst KF for that particular selection after the stat fcst run. here you would need to check if the diaggregated values are good enough.
    hope it helps.

  • SUS - Added Data Type Enhancement and Higher level Proxies are not active

    Hello,
    I've added a field to our current data type enhancement Z_Purchase_Order_Item.  Once I regenerate the proxy on the enhancement and activate it the field appears as it should in the high level items that use the enhancement (PurchaseOrderRequest_In).  But those proxies have become inactive and when I try to activate them I get this message:
    Interface II_BBPX1_SUS_PO was repaired before the Modification Assistant was enabled. 
    All Modification Assistant functions only apply to future modifications, not to those already
    undertaken.  This means:
    -The modification overview only displays future modifications.
    -When resetting to the standard, the system will reset all objects to their current version, since
    the actual standard can no longer be identified by the Modification Assistant.
    -Support for adjustment after an upgrade will only be available for future modifications. 
    Modifications that already exist must be re-made manually using version management.
    The next message says:
    Object can only be created in SAP package.
    Then the status bar shows "Proxy Activated".  But when I close and reopen the proxy I see that it is once again inactive. 
    Does any know what I need to do to activate this proxy? 
    Thanks,
    Matt

    In SPROXY you can open your proxy and then view the Activation Log under the GoTo menu.  The log will explain better what the problems might be.  In my case I needed to activate another data type enhancement first.
    Thanks,
    Matt

  • How to change the order of cascading prompt?[The prompt at higher level appears at TOP]

    Hi Guys,
    I have one doubt in cascading prompt without Hierarchy view in UNIVERSE 3.1
    While running a report with it.
    The prompt at higher level appears below the prompt at lower level.How can we change the order,i.e, I want Level 2 Account Code as top and then Level 3 Account Code ?
    It can achieve in hierarchy view,but i don't want to set it as hierarchy view,because there are huge number of Level 2 Account code[Search pattern is not available too]
    Thanks in Advance
    Shenbu

    Hi Sathish,
    Thanks for your reply.
    I created Cascading list of value as you said only.please find below screenshot for your refefrence.
    I think,its tool  limitation as "The prompt at higher level appears below the prompt at lower level in report".Can any other way is there to achieve?

  • Why does OWB 9.2 generate UK's on higher levels of a dimension?

    When you specify levels in a dimension, OWB 9.2 generates unique key constraints in the table properties for every level, but only the UK on the lowest level is visible in the configuration properties. Why then are these higher level UK's generated? Is this a half baked attempt to implement the possiblility to generate a snow flake model in OWB?
    Jaap.

    Piotr, Roald and others,
    This is indeed a topic we spend a lot of our time on these past months. We are addressing this as (in my old days I had the same problem as a consultant) we know that this is a common problem.
    So the solution is one that goes in 2 directions:
    - Snowflake support
    - Advanced dimension data loading
    Snowflake is obvious, may not be desired for various reasons but we will start supporting this and loading data for it in mapping.
    If you want a star table, you will know that a completely flattened table with day at the lowest level will not be able to get you a unique entry for month. So what people tend to do is one of the following:
    - Proclaim the first of the month the Month entry point (this stays closest to the star table and simply relies on semantics on both ETL and query side).
    - Create extra day level entries which simbolize the month, so you have a day level with extra entries
    - Create views, extra tables etc to cover the extra data
    - Create a data set within the tables that solves the key problem
    We have opted for the last one. What you need to do for this is a set of records that uniquely identify any record in any level. Then you add a key which links to the dimension at the same point (a dimension key), so all facts always use this surrogate key to link (makes life in query tools easier).
    For a time dimension you will have a set of day records with their months etc in them (the regular star). Then you add a set of records with NULL in the day having months and up. And you go up the hierarchy. For this we will have the ETL logic (in other words you as a designer do not worry about this!). On the query tool you must be a little cautious on counts but this is doable and minor.
    As you can see none of the solutions are completely transparent, but we believe this is one that solves a lot of problems and gives you the best of all worlds. We will also support the same data structure in the OLAP dimensions for the database as well in the relational dimension. NOTE that there are some disclaimers with this as we are doing software here...
    In principal however we will solve your problem.
    Hope this explains some of our plans in this area.
    Jean-Pierre

  • High Level Bin Search, before Storage Type Search

    Hi,
    Can anyone help me to guide, which user Exit/Badi, be used for searching Empty bins, before storage type search. I come to know from one of colleague below message.
    "" if you want to check the quantities on a higher level (before storage type search ), you can use the user exit "+++".""
    I am unable to understand which kind of user exit "+++".
    Background: Want to do putaway with storage type 007: Our high rack is  having space (Bins) with different capacity. One rack can have 4 type of racks.
    We want to putaway material with different bin types in one storage type.
    Regards,
    Mainsh Gupta

    Hi Vijay,
    Thanks for your quick reply. I am trying user exit given by you. Once again I would like to submit my requirements here.
    a) We have 98 racks in Warehouse.
    b) Product is Ball Bearing.
    c) Bearings are handeled in Ea, Issue and Stock unit is Ea
    d) Alternate Unit of Measure is Box, i.e. per box quantity is mentioned into Material Master.
    e) Each Rack is having 5 different type of bins.
    f) We want to fill rack from bottom to top for first rack, and then next rack.
    g) Once we do putaway for any material, each time system should pick Next empty bin, and each bin type is different.
    Case 1) If going with Storage Type 007: 
                    i) Need to maintain palletization data in Material master WM view 2.
                   ii) Can not maintain any capacity check for Capacity utilization in Material Master. Capacity is only Pallatization data.
                  iii) While creating TO, System goes for placemet of material from bottom to Top in Rack, but give similar quantity for each bin,  &  these quantities are defined from Material Master from Palletization data.
                  iv) In this case it is not checking bin capacity.
    My query:
    i)  How can we split quantity during TO Creation based on Next Empty Bin avaialbe with certain capacity and all further bins with other capacity.
    ii) Can we have different type of bins in one storage type if we are going for Storage type 007. or it is mandatory to have similar kind of bins.
    Case 2) If going for Storage type 002:
                  i) Not maintined Palletiztaion data in Material master.
                 ii) Maintining capacity check in WM View 1.
                iii) Maintained Capacity check in Bin master.
                iv) WHile careting TO , system doesnot spilt quantity for next empty bins avaialbe, Only one line item comes for whole quantities. and system throw an error.
    Message Number: Message no. L3068
    Message Details: Maximum quantity for storage bin TR-15 will be exceeded by 740.000 PC
    My query: How can we split TO quantity as per next empty bins available.
    If you will give me your contact number, I can speak to you over phone and eleborate in more details for your clear understanding my issue.
    Regards,
    Manish

  • High Level Recommendations For Multi-Tier Application

    Hello:
    I have been reviewing Windows Azure documentation and I'm still somewhat confused/unsure regarding which configuration and set of services is best for my organization.  I will start off by giving a high level description of the what the environment
    should be.
    A) 2 "Front End" IIS Instances, Load Balanced running an MVC 4.0/.Net 4.5 Web Application
    B) A "dedicated" SQL SERVER 2008 R2 server with medium-high resources (ample RAM and processing power)
    C) An application server which hosts a Windows Service.  This service will require access to the SQL Server listed in B. In addition the IIS "Front Ends" listed in A should have access to a "shared" folder or directory where files
    can be dropped and processed by this windows service.
    I have looked at Azure Web Site, Azure Virtual Machines and Cloud Services and I'm not sure what is best for our situation.  If we went with Azure Web Sites, do we need TWO virtual machines, or a single virtual which can "scale out" up to
    6 instances.  We would get a Standard Web Site, and the documentation I see says it can scale out to 6 instances. I'm somewhat confused regarding the difference between a "Virtual Machine" and an "Instance".  In addition, does
    Azure Web Sites come with built in load balancing between instances, virtual machines? both?  Or is it better to go with Azure Virtual Machines and host the IIS Front end there?  I'm just looking for a brief description/advise as to which would be
    better.
    Regarding the SQL Server database, is there a benefit to using Azure SQL Database? Or should we go with a virtual machine with SQL Server installed as the primary template?  We have an existing SQL Server database and initially we would like to move
    up our existing schema to the Cloud.  We are looking for decent processing power for the database and RAM.
    Finally the "application" tier, which requires a Windows Service. Is an Azure Virtual Machine the best route to take? If so, can an Azure Web Site (given that is the best setup for our needs) write to a shared folder/drive on a secondary virtual
    machine.  Basically there will be json instruction files dropped  into a folder which the application tier will pick up, de-serialize and do backend processing.
    As a final question, if we also wanted to use SSRS, is there updated/affordable pricing and hosting options for this as well?
    I appreciate any feedback or advice.  We are definitely leaning towards Azure and I am trying to wrap my head around what our best configuration and service selection should be.
    Thanks in advance

    Hi,
    A) 2 "Front End" IIS Instances, Load Balanced running an MVC 4.0/.Net 4.5 Web Application
    B) A "dedicated" SQL SERVER 2008 R2 server with medium-high resources (ample RAM and processing power)
    C) An application server which hosts a Windows Service.  This service will require access to the SQL Server listed in B. In addition the IIS "Front Ends" listed in A should have access to a "shared" folder or directory where files can be dropped and
    processed by this windows service.
    Base on my experience and your requirement, you could try to use this solution:
    1.Two cloud service to host your "front end" web application. Considering to Load Balanced, You could use traffic manager to set Load Balancing Settings.
    2. About sql server or ssrs, you have two choice:>1,create a sql server vm  >2, use sql azure and azure ssrs
    I guess all of them could meet your requirement.
    3. About your C requirement, which type application is? If it is website, You could host it on azure website or cloud service.
    And if you want to manage the file by your code, I think you could save your file into azure blob storage. You could add,delete file using rest API(http://msdn.microsoft.com/en-us/library/windowsazure/dd135733.aspx
    ) or code(http://www.windowsazure.com/en-us/documentation/articles/storage-dotnet-how-to-use-blobs-20/ ). And the Blob storage could be as a share file
    folder.
    And for accurately, about the billing question , you could ask azure billing support for more details.
    try this:http://www.windowsazure.com/en-us/support/contact/
    Hope it helps.
    Regards,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • High level OBIEE diagram?

    Hi, I'm wondering if anyone has a very high level OBIEE diagram, suitable for given new users a 10,000 foot view of the OBIEE system. I.e. something that shows browser talking to presentation services talking to BI Server talking to databases.
    Does anyone have anything I can blatently steal...ummm I mean reutilize?
    Thx,
    Scott

    SPowell42 wrote:
    Hi, I'm wondering if anyone has a very high level OBIEE diagram, suitable for given new users a 10,000 foot view of the OBIEE system. I.e. something that shows browser talking to presentation services talking to BI Server talking to databases.
    Does anyone have anything I can blatently steal...ummm I mean reutilize?
    Thx,
    ScottHi scott,
    There are ton's of images out there ( Not literally in tons but you know what I mean).
    Follow this link: ( https://www.google.com/search?hl=en&sugexp=les%3B&tok=3m7SX0LbsZH2wJ71o09isg&cp=26&gs_id=3&xhr=t&q=obiee+architecture+diagram&bav=on.2,or.r_gc.r_pw.r_qf.&biw=1206&bih=647&wrapid=tljp134512990497400&um=1&ie=UTF-8&tbm=isch&source=og&sa=N&tab=wi&ei=sg0tULUC4cvRAdmPgMgC )
    Feel free to re-utilize them as you wish :)

  • ME9F generates authorisation High level risks, why?

    Hi All!
    Please, advise why transaction ME9F - Message Output: Purchase Orders generates High level risks with such transactions as
    MK01     Create vendor (Purchasing)
    MK02     Change vendor (Purchasing)
    XK02     Change vendor (centrally)
    MIGO     Goods movement
    ME54     Release Purchase Requisition
    MI04     Enter Inventory Count with Document
    ME28     Release Purchase Order
    etc. As I understand this transsaction is used for view and printing of output. Why such risks as "Enter Purch Agreements & create/modify fictious Vendor " or "Ability to create a purchase contract and release PO" come up?
    In what conditions such risks can be reasonable?
    Thank you

    Looking through really old posts of mine I saw that I had given this question a brain-dead answer years ago. I seriously doubt the poster is still looking for a solution (I certainly hope not) :) Almost assuredly the problem is because of a mismatch in data types. TRUNC(s1.date1,'DD') won't produce a number but rather a date truncated to midnight. TO_CHAR(TRUNC(s1.date1,'DD'), 'DD') will produce a number. It's difficult to tell from the code what the poster is trying to do, so I can't tell if that's the answer.
    P.S. I wasn't actually trying to bring this post to the top of the thread -- I was just editing what was clearly an incorrect answer.
    Edited by: matthew_morris on May 9, 2012 8:31 AM

  • Planning at higher level

    Hi all,
    We are implementing multiple Planning, Budgeting and Forecasting. Budgeting and Forecasting will be done at the base level whereas Planning is done at the higher level. Now the concern I have is in BPC we can not post data at parent level so is it even possible to Plan at higher level.
    If yes, then how can we do it. Please share your views.
    Thanks,
    Diksha.

    Hi Rich,
    Thanks for your reply.  I have some more questions on this document.
    1. If I want to plan at a much higher level , will this BADI work.  Say for  example: the base level members are at level 6, I want to plan at level 2 or level 3.  Will it still write the records to level 6 members though they are not immediate dependants.
    2. In the example given in the document, both the base level members and the parent member is in the input schedule.   If I don't have the base level members shown in the input schedule, and I only have the parent member, will this BADI still post data to the base members.
    For example:  I have some 500 base members to one parent node.  I don't want to display the 500 base members.  I will only have one parent member in the input schedule and post data to that member only.  Will it still say that 500 records are submitted.
    How is the scoping done for this BADI. Generally for the default logic, scoping will be based on the members on the input schedule. 
    Thanks
    Anjali

  • Using High-Level API, need to use KeyRelease just for Lists

    I'm coding a MIDlet with High-Level API, but I found that is really annoying to press down 30 times in a long List to reach the item you want to select. So I thought "what about pressing right/left and make it working like pressing down/up like 10 times"?
    Something like this:
    Canvas canvas = new Canvas() {
             public void paint(Graphics g) { }
             protected void keyPressed(int keyCode) {
                switch(keyCode) {
                    case -3:mylist.setSelectedIndex(mylist.getSelectedIndex()-10,true);break;
                    case -4:mylist.setSelectedIndex(mylist.getSelectedIndex()+10,true);
          }; // end of anonymous class*/But I have no idea about how to implement this =(

    first of all, is there any particular reason you want to stick to the high-level API?
    Well, I have already nearly 700 lines of code. I don't want to start from 0 :P
    I think the best way to implement this would be to use customItems so you can control the view of the list.
    I think that requires MIDP2.0 I'm trying to make it work in MIDP 1.0
    The best you could do with high level UI is add navigation Commands to the List.
    I have already 2 Commands per List. Not all phones have a button in the center of "cursors", so I use right button for select and left for back/exit.
    Thanks for replies anyway

  • Maintain Columns for Higher Levels in Hierarchy when using Drill Down

    Hello all,
    I've searched through this forum looking for an answer to this, since I thought it might be a common question, but I wasn't able to find any related content.  So I apologize if this has already been answered in the past.
    I would like to know if when drilling down in a WEBI report, it is possible to automatically add dimension columns to a report as you drill down to the lower levels in the heirarchy, and keep the columns with the higher level dimension values, rather than replace those columns, which is the default behavior.  As a simple example, suppose I have the following columns in a report:
       Product      Sales Amount
    Now suppose I have set up a heirarchy in the Universe with Product, Sub-Product, then Region, in that order.  In the WEBI report with the drill filter options enabled, when I click on the Product link, the default behavior is to replace the Product column with the Sub-Product dimension and display the following:
      Sub-Product  Sales Amount
    Instead, I would like it to display:
      Product Sub-Product Sales Amount
    Then subsequently, of course:
       Product Sub-Product Region Sales Amount
    Does anybody know of a simple way to accomplish this?  I suppose this could be accomplished using the openDocument method with links to separate reports showing the addtional columns, but this seems a bit complicated for a relatively smple requirement.  I'm hoping that there is an existing simpler solution to this problem.  Please advise.  Any information would be greatly appreciated.

    Bernardo,
    The drill down capability is vertical and not horizontal.  There are two solutions, the one of open document as you mentioned is one.  The other solution depends on the way you have deployed your system.  If you have given users the capability to run reports in "modify" mode (WebI), then they can insert columns to the grid according to the scenario you mention
    Product Sub-Product Sales Amount
    and forego using the "drill fiter" per se.  If your deployment only permits most users to view the report in "read-only" mode (InfoView), then you have limited options.
    Thanks,
    John

Maybe you are looking for

  • Photoshop CC flickering on Macbook Pro?

    Hey guys. So I got a new Macbook Pro less than a month ago, mostly for drawing and such. I've encountered a problem, though, and that is that when I use Photoshop CC, the screen flickers! Not the entire screen, but the window in photoshop. This seems

  • How to get the filename in mapping when using sender File adapter?

    hi Experts,    I have scenario where XI reads the input file using Sender file adapter.    The file name is configured in the communication channel.    In my message mapping it is possible to read this file name? Thanks gopal

  • 1st movie uploaded to youtube plays @ double speed

    Using a 4-year-old 13" MacBook with iMovie HD 6.0.3 I created a 36-second video which, when uploaded to youtube, has the video playing at double speed but the audio playing normally until the audio gets cut off since the video now has been reduced to

  • Modifying a template

    I have a project with 200 forms more or less. Now I need to modify a template, and I know I would open all the fmbs and save them. How can I optimize this process ? I use Project Builder and think that It can help me with a Macro, but not sure. Any s

  • Crystal Rpts XI runtime error

    When trying to open the calendar to enter a date range in a custom report I get a runtime error: objected expected in line:78. I installed the monthly hotfix 12 version 11.0.0.2182 but it didn't help. I would refresh the report >> prompt for new para