MSI 890FXA-GD65 not posting please help!!!

Hi everyone I am new to the site and I am doing my second build first time with a MSI board here are my componets.
1: MSI 890FX-GD65
2: AMD PHENOM II X4 980 BLACK EDITION 3.7 AM3 SOCKET
3: G.SKILL Sniper Low Voltage Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
4: SAPPHIRE FleX 100314FLEX Radeon HD 6870 1GB 256-bit GDDR5
5:  CORSAIR Builder Series CX500 V2 500W ATX12V v2.3 80 PLUS Certified Active PFC Power Supply\
Here is the issue I did the minum connections before putting the computer in the case to make sure it would POST, but it doesn't. The motherboard speaker doesn't make a sound but the 8 led lights on top of the MOBO are all lit. I cant get any response from my monitor when its hooked up to my video card. the fan from the PSU and video cards are spinning but again no POST can anyone help Me with this thank you., also I used a second power supply and still no POST or response from the monitor but again all the fans are working and all 8 of the led lights are lit at the top of the MOBO. once again thanks for your help.

Good evening!
All parts are new?
Use a single stick of memory.
Recheck all power connections are well in place, and don't forget the one near and for the processor.
Don't think that is the problem, but for good measure you should also reseat the graphics card.
I'm not sure whether this mobo has a speaker.

Similar Messages

  • MSI P67A-GD65 Not Posting, unsure of beep code meaning

    Just swapped out my old K9A platinum for a P67A-GD65 and I can't seem to get it to post. I'm getting a beep code of five beeps (long ones maybe? google indicates "process error") but I'm not sure what that means. Pulled the video card, tried my two sticks of ram in slot 1 one at a time, disconnected every device but still getting the same code. Any ideas on what might be causing this?
    Edit: Tried clearing the CMOS as well but no luck
    Sound @ post:
    Memo.m4a - 0.11MB
    Specs:
    MSI P67A-GD65 (B3) Motherboard
    Intel Core i7-2600K processor
    G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) ram
    CORSAIR CMPSU-750TX 750W ATX12V / EPS12V power supply
    MSI R5770 Hawk Radeon HD 5770 1GB 128-bit GDDR5 PCI Express 2.1 x16 graphics card

    It seems I'm not the only one having weird issues with this board. I have the exact same board, v1.8 BIOS and Gskill F3-17000CL9D-8GBXLD memory.
    If I enable the XMP profile for this memory, this system will not post. It does not matter if I raise the DRAM voltage and I/O (memory controller) voltage to their acceptable limits, it does not matter if I manually enter in the timings of the memory specified on the box. XMP = no post.
    So after disabling XMP I kept the memory at 1600mhz, which worked fine. I decided to try 1866mhz and a little more voltage. This seemed to work fine...for awhile. This morning my system would not post. I had to clear the CMOS (not use the jumper but literally remove the battery). Ever since then my system will BSOD after a few minutes on startup unless I manually enter in my memory timings (I tried two sticks from different vendors).
    I know I don't have bad memory, and the fact is that this board will not post with vendor specified settings.
    All I can suggest is to pull the CMOS battery and try one stick of memory.

  • Random lock ups with MSI P67A-GD65 (B3). Please help!

    Hello all,
    I just built a new system with the following components:
    MSI P67A-GD65 (B3)
    Intel Core i7-2600K Sandy Bridge 3.4GHz
    EVGA 012-P3-1570-AR GeForce GTX 570
    G.SKILL Ripjaws X Series 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
    Thermaltake Black Widow W0319RU 850W ATX 12V  PSU
    Antec Lanboy air case
    2X Western Digital VelociRaptor WD1500HLFS 150GB in RAID0 running Windows 7 Pro 64 bit
    This was supposed to be my dream computer, but it has turned into a nightmare! It locks up constantly.  Usually the mouse pointer will disappear and the computer will just freeze up.  This normally seems to occur after the computer has been idle for a while.  I have read that there might be compatibility issues with the MSI P67A-GD65 and the GTX 570 video cards.  Can anyone confirm this?  Any suggestions on how to troubleshoot this?  The only thing event viewer is showing is the unexpected shutdown when I have to power cycle it.  Thanks in advance!

    Quote from: HU16E on 12-April-11, 11:26:00
    That can happen, & it can really mess things up if two kits are attempted to be run together. The platform is DDR3 1333 as to native support by the CPU IMC. If the system can't run on 1333 RAM speed at CR 1, 9 9 9 24 @ 1.50v's, then something is wrong. No system should ever have to use an OC (or X.M.P.) as a workaround to make it work. That's why I recommended the Crucial 1333. Plug one stick in the blue primary dimm slot to get everything loaded & checked out, & go from there.
    Exactly which SATA ports are you using for the HDD's & RAID? White Marvell or Intel SATA III, or the black SATA II? 
    Unfortunately, my local shop didn't have the Crucial, so I grabbed the Corsair instead.  The Velociraptors are running from SATA 1 and 2 (the top white connectors).  I also have 2X HITACHI Deskstar 2TB 7200 RPM 64MB Cache SATA 6.0Gb/s running in RAID0 from SATA 3 and 4 for storage (this computer is intended for HD video editing, compositing in After Effects, etc.).  Sorry I forgot to mention that in the original post!

  • Msi 890fxa-gd65 USB and video dying after extended use

    Multiple times this has happened to me. I will be playing a game for a while (2+ hours) and all the sudden my mouse, keyboard, and monitor will all black out and shut off. My computer is still running and the buttons on the front of the case to shut the computer off no longer work either.
    I know it's not a heat issue because i touched the heat sinks on the mobo and they are not hot at all.
    I have taken the board and exchanged it at frys; this is the 2nd board so i'm pretty sure its nothing wrong with the board.
    Help me please!
    Specs:
    Mobo: msi 890fxa-gd65
    Ram: G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600
    Video: EVGA GTI 550
    PSU: Cooler master GX 750
    CPU fan: Zalman
    HDD: Western Digital Caviar Green WD10EADS 1TB 32MB Cache SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive
    OS: Windows 7

    Quote
    Why then does MSi mainboard default to this speed?
    Steve64, do yourself a favour and search for RAM SPD profiles on the net. Memory module manufacturers write the SPD information to the EEPROM on the module. Motherboard BIOSes read the SPD information to configure the memory controller. If that SPD profile is not in line with the native RAM speed supported by the CPU, then the board's BIOS will be set to the incorrect memory speed as can be seen in this post. Its an industry design standard (JEDEC) and the memory manufacturer is the cause of the incorrect setting when the user buys an incompatible set of memory.
    The rest of your post has been removed as it adds no value to finding a solution.

  • Multiple Problems with MSI 890FXA-GD65

    I am having problems getting a clean build of new components to work.  The components are:
    motherboard is MSI 890FXA-GD65
    processor is AMD Phenom II X2 565 Callisto
    memory is 2x 4Gb G.Skill Ripjaws X model F2-12800CL9D (CAS 9, Unbuffered DDR3 1600)
    disk drive is a Western Digital Caviar Black WD1002FAEX 1 TB SATA III
    card is an MSI N460GTX Cyclone 768D5/OC.
    power supply is an Antec NEO ECO 620C 620W
    operating system is Windows 7
    All items are brand new, and being assembled for the first time, so nothing is overclocked.
    I have three problems.  First is that the video output is flaky.  I initially thought that the board wasn't POSTing, because I was getting no audible 'beeps' and there was no display output (does this board not have a speaker or speaker header?).  Through trial and error, I discovered that the board was POSTing, but I could not see anything because of a strange video problem:
    If the monitor is connected when the video output changes, then the video will not work, and disconnecting/reconnecting will not fix it. For example. If the video cable is plugged in during a cold start, I will get no video output. If I wait a few seconds until the Bios loads, and then plug in the video, then I get a video signal. However, if I leave it plugged in as the video output switches when Windows starts up, then I lose video again. Only by plugging in and then unplugging during the same video output mode can I use the output.
    I have tried 2 different video cards (same mdodel number) with the same result.  I have tried switching my memory with only 1 stick and with both sticks installed.  I don't have another processor to try.
    The second problem is that Windows will not run with the USB controller turned on in BIOS.  It starts 'loading files' and then just hangs.
    The third problem is that the MSI utility program will not run properly.  I tried to install the updated chipset drivers, but the installation hangs.
    Thanks for any help!!  I am on the verge of returning the board to NewEgg after many hours of trying to troubleshoot this build.

    Quote from: JimmyK on 15-February-11, 22:22:46
    Thanks for the reply.
    Sorry to be so newby, but where do I start memtest?  The reported BIOS is the same version/date code as what is available from MSI...
    >>Memtest86<<
    Quote from: JimmyK on 15-February-11, 22:26:23
    Thanks for the reply.  I am using the DVI output on the video card connected to a VGA monitor with an DVI-VGA adapter.
    No external USB connections have ever been installed.
    I don't have any other DDR3 laying around.  Is there a recommended memory list on the MSI site?  I couldn't find one.
    Regards
    http://www.msi.com/file/test_report/TR10_2220.pdf
    However its down to the CPU as memory controller is there.
    You should use AMD tested memory sticks

  • I do not use or have not signed up for a MobileMe Account but I am getting duplicates in my iCal for some reason.  All discussions I read are pointing to the MobileMe being the problem but it is not.  Please help me.  There must be another reason.

    I do not use or have not signed up for a MobileMe Account but I am getting duplicates in my iCal for some reason.  All discussions I read are pointing to the MobileMe being the problem but it is not.  Please help me.  There must be another reason all my entries appear twice. 

    If you wish to submit comments to Apple, the best way is to use their feedback pages.
    http://www.apple.com/feedback/itunesapp.html
    It's not likely that anyone from Apple will see your comments here among the thousands of other posts.
    Regards.

  • MSI 890FXA-GD65 North Bridge Temperatures

    Hi there I have recently purchased the MSI 890FXA-GD65 for a new build. The thing that suprises me is that the temps on the North Bridge are very random. It normaly stays in the 55 C- 65 C range, but it is constantly jumping up and down in a matter of seconds. For example it goes from 58C to 65C in a second and then could drop to 55C the next second and after that could jump to 70C and it just continues playing. I am wondering if anyone else has the same issue with the readings and what could be the cause of ti?

    I am waiting for a memory at the moment. However the airflow in my case is more than adequate, GPU idles at 30C and does not exceed 50 under load with the fan at 25% of the max speed. The CPU is well cooled with no fans on the heatsink (Thermalright Black 120), idling at 25C and going to 45C under load and overclocked. The RAM modules are very cool on touch as well and my MB shows constant temperature of 28C - 30C. I think its something wrong with the diode, because there is no way that the temp would jump from 55 to 70 in a second and the next second to come back down to 60. I was just wondering if someone else has similar thing with their mobo. I have got 3 year warranty on it so I am not that worried about it, plus it is not crashing or anything, its just the readings.
    P.S. I forgot to mention that this is not detected as NB on any program. Instead on AIDA64 shows up as AUX temperature, and on HW Monitor comes up as TMPIN1, but I read it corresponds to NB usually. Plus this is the warmest part on touch.

  • HT201412 my iphone 4s does not start by power switch, it starts when i connect to pc. the proximity sensor is not working. please help

    my iphone 4s does not start by power switch, it starts when i connect to pc. the proximity sensor is not working. please help.

    Sounds like it may be a hardware issue.
    Please contact Apple Support in your country.
    Here is a list of numbers: http://support.apple.com/kb/HE57
    Regards
    J

  • I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4

    I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4

    I have unabled 5 fingure gesture now not able to perform any task,also my power button is not working,please help me in removing this gesture,using I phone 4

  • I have 4s iPhone , I download the iOS 7. Now the front receiver microphone is not working , please help me that how to fix the problem.

    I have 4s iPhone , I download the iOS 7. Now the front receiver microphone is not working , please help me that how to fix the problem.

    I live in South Africa, and I had the same problem with my iPhone 4.
    After weeks of frustration and swearing, I was in the process of restoring my phone to a previous iOS. To do that you need to turn the "Find my iPhone" option off, since i turned it off, my problem was solved. No need to repair anything or revert back to old iOS.
    ***** that i cant use Find my iPhone, but atleast i can use my phone.

  • I installed windows 7 on my macbook pro. all is working but lan adaptor and sound od laptop is not working. please help me or send the link where i can download the these drivers.

    I installed windows 7 on my macbook pro. all is working but lan adaptor and sound od laptop is not working. please help me or send the link where i can download the these drivers.I have lost my resource cd .

    If you are running Lion or Mountain Lion, the drivers are downloaded from within Bootcamp Assistant. If you are running Snow Leopard the drivers are on your Snow Leopard install disk.
    Read the Bootcamp Install Guide for your version of OSx. http://www.apple.com/support/bootcamp/
    Bootcamp questions should be asked in the Bootcamp forum where the Bootcamp gurus hang out https://discussions.apple.com/community/windows_software/boot_camp

  • I have a problem with itunes when I sync the saved music and want to sync my iphone 5 ios 7.0.6 no longer passes the music thing is that just stays on "waiting for sync" and not worry please help are more than 400 songs that do not want to hear who are wi

    I have a problem with itunes when I sync the saved music and want to sync my iphone 5 ios 7.0.6 no longer passes the music thing is that just stays on "waiting for sync" and not worry please help are more than 400 songs that do not want to hear who are wi

    Plawexki wrote:
    ...  do you know if the contacts, photos, messages etc will be wiped?
    Yes... Everything will be Wiped and Replaced with what is currently on Your Mac.
    SYNCING with iTunes
    See here  >  http://support.apple.com/kb/HT1386
    From Here  >  http://www.apple.com/support/iphone/syncing/
    You may find this information of interest...
    Have a read here...
    https://discussions.apple.com/message/18409815?ac_cid=ha
    And See Here...
    How to Use Multiple iDevices with One Computer

  • HT1918 I would like to change my Visa card from the account but its not changing and the billing information is not changing and I can't purchase any thing from my account its now not usable please help me to solve the problem

    I would like to change my Visa card from the account but its not changing and the billing information is not changing and I can't purchase any thing from my account its now not usable please help me to solve the problem

    You made a purchase and exhausted the credit on your card before it processed. All purchases are final. Contact iTunes Store support. You need to settle up before you can purchase or download anything else.

  • HT4796 I have made a file using the Pages app.I mailed it to a friend.When she tried opening the same file on her pc at home , It did not open.Please help me as to how to open the file in the Microsoft word format on her pc.

    I have made a file using the Pages app.I mailed it to a friend.When she tried opening the same file on her pc at home , It did not open.Please help me as to how to open the file in the Microsoft word format on her pc.

    Send it as a PDF.

  • TS1814 I have windows vista and this did not work for my ipod it still will not update PLEASE HELP!

    I have windows vista and this did not work for my ipod it still will not update PLEASE HELP!
    iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server

    Try this:
    Close your iTunes,
    Go to command Prompt -
    (Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
    (Win XP SP2 n above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
    In the "Command Prompt" screen, type in
    netsh winsock reset
    Hit "ENTER" key
    Restart your computer.
    If you do get a prompt after restart windows to remap LSP, just click NO.
    Now launch your iTunes and see if it is working now.
    If you are still having these type of problems after trying the winsock reset, refer to this article to identify which software in your system is inserting LSP:
    iTunes 10.5 for Windows: May see performance issues and blank iTunes Store
    http://support.apple.com/kb/TS4123?viewlocale=en_US

Maybe you are looking for