MSI Eclipse SLI and OCZ Reaper 1866MHz memory OC

Hi there!
I have a problem with my board (I think) and memory. Everytime I try to overclock my CPU to 4GHz and my memory to 1600MHz my PC restarts after few minutes in windows :/ Also if I want to overclock my CPU should I change something on that switch on the motherboard? I think it's called CPU_CLK1 the red one with white switches.
I got this RAM: http://www.newegg.ca/Product/Product.aspx?Item=N82E16820227382&nm_mc=OTC-PricebatCA&cm_mmc=OTC-PricebatCA-_-Memory+(Desktop+Memory)-_-OCZ+Technology-_-20227382
I tried to set them at 1600MHz 8-8-8-28 (crash) 9-9-9-28 (crash) :/ And I need some help with CPU. I overclocked only AMD CPUs, and my record on X4 920 2.8GHz was 4.2 stable :P But never OCd an Intel CPU, specially i7. Can someone help me?
Oh I almost forgot... Why my mobo recognize my RAM as 1066MHz? :/

Quote from: sp4wners on 15-September-09, 23:25:30
Also if I want to overclock my CPU should I change something on that switch on the motherboard? I think it's called CPU_CLK1 the red one with white switches.
Don't use the OC switches.
Quote from: sp4wners on 15-September-09, 23:25:30
I tried to set them at 1600MHz 8-8-8-28 (crash) 9-9-9-28 (crash) :/ And I need some help with CPU.
One assumes you did increase the DIMM voltage?
Quote from: sp4wners on 15-September-09, 23:25:30
Oh I almost forgot... Why my mobo recognize my RAM as 1066MHz? :/
Because that's what it is.

Similar Messages

  • MSI Eclipse Sli and Asus 6950 Direct CU II problem

    I’ve recently bought the Asus 6950 Direct CU II 2GB. After I installed it a weird buzzing sound started coming from around the area, where the big heat sink below the cpu socket sits. That only happened when the graphics card was on high profile and particularly when I was in any game.
    About a month later my card stopped working properly so thinking it was its fault I used the warranty and got it replaced. However with the new card the system won’t even start. My monitor goes from “Please check signal cable” to “No signal” and apparently the system is not even moving past the bios checks.
    The weird think is that when I use my old card (MSI R4870 1GB) the system seems to work properly!!! I tried the 6950 in two different systems and it seems to be working….
    I’ve tried resetting the bios removing other devises to test the power supply etc., but nothing works, I can only think that something is wrong with the motherboard.
    Any ideas on what might be wrong???
    My system is:
    MB: MSI Eclipse Sli
    CPU: Core I7 920
    PSU: TAGAN TG700-U88 PIPEROCK SERIES 700W
    RAM: 3 x CORSAIR TR3X6G1600C9 Triple DDR3
    HDD: WD Velociraptor 150GB for the OS

    Thanks for the timely reply HU16E.
    I don't have another psu available right now but I will in 3 days so I will try that.
    On the other hand I have mine working as a single rail from the day I bought it (turbo mode switch on the psu), but i am not sure how this can be connected.
    Also while I was playing around with the system it started up, only once, with the 6950, and that happened with everything connected so I still can't figure what the hell is happening!!!! I am thinking that something on the pcie port is wrong so i tried on the other ports too, yet nothing happened.
    I am still leaning towards the motherboard but any other ideas would be welcomed.

  • MSI Eclipse SLI and USB ports

    I have reinstalled Windows 7 fresh with formatting HD
    Now whenever I plug a memory card (even on the motherboard ports) in any of the USB ports I get the message
    "The USB device can perform faster if you connect it to a High Speed USB 2.0 port"
    I reread the book, rechecked the connections, under device manager I have 8 Intel ICH10 Family USB enhanced host controller and underneath them i have another set of 8 root hubs -
    The transfer speed is definetly USB1 (under 14mb/s) (in other pc core2duo e6400 - windows 7 the rate was almost 20mb/s)
    Anyone has a clue - there are no drivers and I don't want to touch the bios before getting some advice
    Thanks guys - you've been extremely helpful before

    I have reinstalled Windows 7 fresh with formatting HD
    Now whenever I plug a memory card (even on the motherboard ports) in any of the USB ports I get the message
    "The USB device can perform faster if you connect it to a High Speed USB 2.0 port"
    I reread the book, rechecked the connections, under device manager I have 8 Intel ICH10 Family USB enhanced host controller and underneath them i have another set of 8 root hubs -
    The transfer speed is definetly USB1 (under 14mb/s) (in other pc core2duo e6400 - windows 7 the rate was almost 20mb/s)
    Anyone has a clue - there are no drivers and I don't want to touch the bios before getting some advice
    Thanks guys - you've been extremely helpful before

  • Settings for OCZ3OB1600LV6GK on MSI Eclipse SLI (X58) and i7 @ 920??

    Hello everybody! 
    Could anyone suggest me the right settings for the RAM (at 1600MHz), in order to pass memtest (in windows) wih no errors?
    I've managed to setup the RAM at 1333 MHz without errors at all and my sytem stable. All the Dimms have been examined one by one and found healthy (via memtest in & out of windows). Thank you in advance!
    Here are my computer specs:
    MSI Eclipse SLI (MS-7520)
    Intel(R) Core(TM) i7 920 @ 2.67 GHz + Noctua NH-U12P SE1366 CPU Cooler
    XFX NVIDIA GeForce GTX 285 (1024 Mbytes - GDDR3)
    OCZ DDR3 PC3-12800 /1600MHz /Value Series /Obsidian XTC Heatspreader /Core i7 Ready /2GB Module /6GB Triple Channel
    WD2500AAKS
    Corsair HX620W Modular Power Supply

    Henry thank u for answering! 
    First image settings (in bios): 9-9-9-24 (1T), Memory Ratio 1333Mhz - Uncore Ratio 2666Mhz, DRAM Voltage -Auto (1.50V), Spead Spectrum Disasbled. PASSES MEMTEST
    Second image settings (in Bios): 9-9-9-24 (1T), Memory Ratio 1600Mhz - Uncore Ratio 3200Mhz, DRAM Voltage 1.65V, Spead Spectrum Disasbled. FAILS MEMTEST
    I have tried a lot of different timings to stabilize at 1600Mhz but no luck  I tried also to icrease the QPI Voltage at 1.35V (as i was suggested by a friend) but i can't read anywhere the default voltage in order to increase it 
    The CPU-Z SPD tab 1st and 2nd image shows some sets of timings which are the same. They differ a lot than the manufacturer's settings (9-9-9-24 1.65v). Which of these should i use? Could you help me a little by being more specific? 
    p.s: Hope you can see the images as they are my first (pic) uploads!
    (Click images to enlarge)
    I made your images clickable.
    -- Mark

  • GTX 470 AND MSI Eclipse SLI

    hi,
    I got a msi eclipse sli  mobo and i going to upgrade my sapphire hd 4870 512mb to a gtx 470.
    but why should i buy an msi gtx 470, does the card make a special connection with the mobo so it performs better than when i would put in an EVGA card ??

    Quote
    but why should i buy an msi gtx 470
    Probably because it is cool to have as much MSI Components in the system as possible (it is a corporate identity kind of thing). 
    Quote
    does the card make a special connection with the mobo
    Not really.
    Quote
    so it performs better than when i would put in an EVGA card
    The performance depends on the cards specs.  If the MSI Version has better specifications (more memory, slightly overclocked etc.), it may perform better than the EVGA Card.  If the cards are identical there is no reason to believe that one would be faster then the other.

  • MOVED: [Athlon64] MSI Diamond-D and OCZ memory compatibility

    This topic has been moved to Overclockers & Modding Corner.
    [Athlon64] MSI Diamond-D and OCZ memory compatibility

    More imortant than the brand are the types of chips used.
    Winbond Bh6 and -Ch5 overclock poor on a AMD64 system, or u need to set the vMem redicoulisly high.
    With Samnsung and Micron chips u can get the same timings @normal voltages (2,7v).
    Here is a list of chips, icw brands:
    http://www.techpowerup.com/memdb/
    Make sure u get Micron 5B G or Samsung TCCD chips !
    Agree with Stick about the amount of memory. First of all: Windows XP (32bit) cannot adress more then 3 GB, furthermore, no way in the world u are gonna use that memory. Stick to 2GB which is more then enough, heck, 1GB is allready more then enough 99,9999% of the time.

  • PC shuts down or reboots spontaneously (MSI Eclipse SLI)

    Starting a new thread to avoid totally hijacking another thread talking about almost the same symptoms here.
    My original post:
    Quote from: Smoke on 05-April-09, 12:43:21
    I get this same situation.. except the event viewer doesnt state anything.
    The system is not bluescreening.. it just hardware powers down and reboots.
    I get the same message as the original poster as well, it is very annoying as it often happens in the middle of doing something.
    I wonder if it could be thermal related to the high IOH temps on the board (often 80-85C, but not sure what happens to them in the middle of playing a game)? Is there any way to log the temperatures to a file so I can check what they were at the time of the crash?
    I get this issue whether I change the default bios settings or not. Ive got a 920 on my eclipse board, my CPU temps are below 30C under load. System temp is about 27C.
    What can I do?
    The following replies:
    Quote from: AaronYuri on 05-April-09, 12:56:57
    That's way too high, even for 100% load.  Reinstall the heatsink.
    Quote from: Smoke on 05-April-09, 20:46:53
    It is? I found another thread on this forum where it was mentioned that intel and msi said the IOH runs hot and to expect temps up to 100C. How do I go about changing the manufacturers heatsink on a board? Ive never done that before and cant find any procedural help thru google...
    Ive been able to replicate the issue by running ram up to high usage. When I get above 98% ram allocation, I spontaneously reboot. So It could be a ram issue as well. Of would that be something possible IOH related as well?
    Quote from: NovJoe on 05-April-09, 23:37:33
    smoke,
    Can you list out your full system spec and PSU spec?
    System Spec:
    Core i7 920 w/ TRUE 120
    MSI eclipse SLI (bios 1.4)
    6x 1gb corsair 1866mhz rated ram sticks (TR3X3G1866C9DF)
    1500w thermaltake psu
    galaxy gtx295 in the primary x16 pci-e slot
    MSI eclipse soundcard in the 1st pci-e x1 slot
    4x 1tb samsung 'UJ' hdd (raid 5)
    O/S (= old winxp 32 bit until I get hold of a 64 bit os) running on 128gb PQI SSD
    lg bluray burner
    All the drives are sata2 and running on the ICHIOR ports.
    For bios settings Ive got the optimised defaults with spread spectrum off and turbo boost on. Once its table then I will OC, but for now its not stable at the baseline yet.
    Temp info:
    IOH temps are as I said, around 80 at startup but rise to at least 87 under load, but not really much further that Ive seen.
    CPU temps are very low with the dual-fan TRUE 120 heatsink. I havet seen it go above 35C with a reasonably heavy processing load. Usually sits about 0-2C above ambient at most when idle.
    System temps get to about 40 under load, or around 27-35 under regular usage, but Im not quite sure what thats measuring the temp of on the board.
    The issue is very frustrating but somewhat intermittent - I can go two days without a crash but then get several in a row. I wasnt previously paying attention to my usage at the time tho so I dont remember what I was doing when it crashed that I wasnt doing when it was fine. I have been able to replicate the crash/reboot/shutdown symptom by running multiple memory intensive apps and loading the ram up to just on the 2.99gb mark (the most winxp 32 bit will 'see') and it goes down. No blue screen though.. its a hardware issue not software I am pretty sure.
    [edit] Updated the ram part number to be correct.

    ok, should I label this possibly as solved?
    I followed MSI's advice and checked through on drivers. Ive got totally up to date drivers, but nvidia just put out a .5  driver update (i mean, its increased the driver version by .50) and so I updated to that. I still got a sft reboot on testing, so no real joy.
    THEN, I did the big change MSI asked me to do - Ive successfully brought my system up to bios 1.5B3 and pow, massive improvements all round!
    Intelburntest runs perfectly now, no crash, no reboot, no errors of any kind. All residuals match. No memory errors. Memtest86 2.11 runs smooth as silk without errors either. PCmark runs out a basic benchmark of almost 19000 (about 3000, or 18.75%, more than the std core i7 920 benchmark without OC'ing) and looks great. Couldnt get that to run previously either.
    The previous methods which 100% of the time would replicate the soft reboot of the system now no longer do so at all (i.e. 0% of the time yet) and for that matter I have not been able to get the box to fall over AT ALL since the new bios.
    I have the same temps on cpu/ioh/system as I did previously. I recall for the same clock speed the cpu was putting out something well under 20 gigaflops... now its a solid 28. I didnt even realise that was a symptom of anything wrong, else the bios does some amazing extras.
    I should note, Im only now using the 'optimised defaults' setting thru the bios. No overclock at all yet.
    I'd love to know what MSI changed from 1.4 to 1.5B3, but whatever it was.. it does appear to have solved my issues. I wont say that conclusively just yet, but I cant bring the system to a crash no matter what I try now where it was rather easy to blow it over with a quiet whistle before.
    Other things Ive noted is that the page file now seems to be actively utilised. Ive pushed it at load up to almost 3gb where before the bios update I was struggling to see 400mb used. Not sure if that was part of it, but if you get simiar issues go straight to MSI and see about getting hold of the 1.5B3 bios or later.
    To quickly address the recent replies:
    1) Ive got to agree with HU16E with my ram. I have no trouble running at the 1333 JDEC spec. And I feel very positive about now being able to achieve the XMP spec with this new bios.
    2) Thanks for the link Aaron. I did end up using the USB flash method from this forum. Worked perfectly. Chalk up another success story!
    3) I did try to swap out the ssd last night, but the system kept soft rebooting while installing the OS on the spin drive. SO I gave up. Seems the ssd isnt a drawback under the new bios tho (assuming it even was a cause earlier).
    4) Ive DL'ed the x64 windows 7 beta and I'll likely as not have a shot installing that and refitting the extra 3gb ram back into the system. I'll let you know how it goes. Theoretically 6x1gb sticks should be as much as 15-20% faster than 3x 2gb sticks (and were about that much cheaper for me at time of purchase) but I'll run some benchmarks now that the benchmarks work and let you know the differences in case anyone wants to build their box the same way.
    Conclusion:
    I'll stress the system over a bit for the next few days without overclocking and I'll see if I can bring the system to reboot like it did previously through high usage, and if I cant I'll change the thread to solved and write out a proper solution post for the problem, symptoms and solution.
    Id like to take the opportunity to say thanks to all the guys who've given me help and advice. Youve all been really great. Thanks a bundle! I owe you one 

  • MSI 990XA-GD55 and Corsair Vengeance 1866mhz problem!

    I got MSI 990XA-GD55 and 2x4GB Corsair Vengeance 1866mhz but i tried everything to get it run at 1866mhz and i couldn't. It doesn't even run at 1600mhz. Only at 1333 or around 1500mhz. I set the timings manually but i doesn't work. Am i doing something wrong? Anyone can help me to figure out?

    Quote from: dyeladreash on 30-May-12, 19:27:53
    By saying memory controller, it's about CPU or mainboard?
    AMD cpu's from the phenom series support 1066/1266/1333/1600(usually only supports that with an overclock and 2 dimms installed) MHZ on the memory controler! only way you can get more frequancy is by overclocking the memory controler on the cpu to allow the increased frequancy on the dimms (most ram that says its 1866mhz is ment that its been tested overclocked at that speed but the chips will more then likely be 1600MHZ)!

  • MSI K8N SLI and AMD FX-60

    Can someone please tell me if the AMD FX-60 CPU is compatible with the
    MSI K8N SLI (MS-7185) version 1.0 motherboard?
    If I upgraded to this processor would its performance be limited by
    the speed of my memory. I have 2.5 Gb PC3200 Corsair RAM.
    Many thanks!

    Quote
    Yes I'm sure its back at 200MHz ie PC3200 but I don't know why the numbers are low. What else would you recommend that I use for benchmarking memory?
    From the below statement I thought you meant you tried to run all 4 memory sticks at 200Mhz, I guess I misunderstood? 
    Quote
    However, I tried it with all four sticks and it also works in dual mode but only in 2T command rate. Although it went into 167 MHz memory frequency but I changed it to 200MHz to get PC3200 (400MHz).
    Obviously from the sceenshot you have 2GB and 2 sticks and are at 1T, but what about 3GB.  I thought you meant running all 4 sticks at 200Mhz from what you said.  That is why I said the score is low.  Sandra is pretty linear when it comes to the bandwidth test.  If memory speed goes down from 200 to 167 that's about 17% reduction, add in 1-3% for 2T in Sandra, and you get very close to your 18% reduction in bandwidth for 3GB test.  Since it sounded like you said you adjusted 3GB to 200Mhz then the score would be too low for the 3GB run, as it appears it is still 166 at 2T.  If that's the case the score is pretty much right on the money.
    BK's recommendations are good for other benchmarks, make sure to try real world apps though too.
    Before you get into overclocking read some of the overclocking guide(like down in the overclocking modding section on the forum)

  • P7N Diamond AND OCZ Reaper 8500 @ 1066

    Any1 who has P7N diamond and is using OCZ reaper 8500 @ 1066 Plz tell me the settings so that finally i can get my system stable . By default it runs at 1.8v @ 800 MHz with 7-7-7-24 timing . How will I get it to 1066MHz with 5-5-5-18 timing . Plz Help me here . Currently I am using C2D E6600 @ 2.4 GHz runnig at stock speed .

    Quote from: ksgehlot on 28-April-09, 15:59:01
    Any1 who has P7N diamond and is using OCZ reaper 8500 @ 1066 Plz tell me the settings so that finally i can get my system stable . By default it runs at 1.8v @ 800 MHz with 7-7-7-24 timing . How will I get it to 1066MHz with 5-5-5-18 timing . Plz Help me here . Currently I am using C2D E6600 @ 2.4 GHz runnig at stock speed .
    Funny, people should read first.
    Running them on 1066MHz instead of 800MHz will get you little to none extra speed.
    The only thing you'll get is the possibilty of an unstable system and maybe a 2 second win.
    Furthermore, it will only be noticeable in benching, in real life you will not know the differ between 800MHz and 1066MHz.
    Just my thoughts on the "1066MHz memory issue", which alot of peeps have lately.

  • MSI K8N SLI and Athon 64 X2 4200+: some problems

    Hi from France
    I've try to upgrade my computer all day long, and still have no solution about this..
    Mainboard: MSI K8N-SLI
    Processor: Athlon 64x2 4200+
    RAM: CORSAIR 1Go *2 PC 3200
    Graphic card: MSI X1950 Pro 256 Mo Radeon
    2 HD (WD 250 Go and WD 160 Go) on IDE 133 (supplied by the mainboard)
    OK, I've connected everything, everythings seems to be well started, the CPU is recognized as ATHLON 64 X2 4200+, and I try to go into BIOS by pressing "DEL", as it is written on my screen (just beside "F11 to boot sequence)
    Nothing happened, it seems that it freezes...
    When I start the computer, I hear my HD starting, the graphic card also, everything...
    But what's going on ??
    I'm a little bit disappointed, it's not the first time I do this kind of upgrade...
    I've rebuilt my computer with "old" configuration MSI K7N L Athlon XP 3000+ and MSI 6600 Geforce
    Every thing is ok
    I don't understand, can somebody helps me
    SOrry for my bad technical english...   

    Quote from: eagle78 on 01-January-07, 07:58:35
    First of all
    HAPPY NEW YEAR (in France, it's done)
    And for my computer, all is allright now
    Like a silly boy, I've connected too much things in the beginning (USB Hub I've forgot not to plug)..
    And so without that, computer boots well, CPU is seeing good, RAM is OK and all the drives..
    Some problems with my OS (XP and SP2), but as somebody says above, I needed to "repair" it, and all is good now
    Thanks for your answer...
    Best regards...
    happy new year  nice everything goes well

  • Is there a big difference between MSI K8N SLI and MSI K8N SLI Platinum motherboa

    i am a bit tight on budget, so I was wondering if I should get the MSI K8N SLI motherboard instead of the MSI K8N SLI Platinum motherboard (my previous choice),.......what do u guys say ?

    Hi,
    Note that he is not talking about the Neo4 versions, looks like in the US MSI has different products:
    Here is the K8N SLI:
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=681
    And here is the K8N NEO4 SLI:
    http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo4/SLI&class=mb
    One has Sound blaster, the other does not.
    Besides, K8N SLI Platinum has only one LAN.
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=641
    While the Neo4 Platinum has two.
    http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo4_Platinum/SLI&class=mb
    A bit confusing right !? Remember that this forum is accessed by people all over the world.
    The thing is that the Neo4 and the related non-Neo are using the same BIOS AFAIK.
    wpr

  • MSI P6N SLI and HDD 2TB

    Hello,
         I intend to buy a new HDD Seagate 2TB ST2000DM001 and I would like to know if my computer will recognize it without a BIOS update.
         My current configuration is:
             MSI P6N SLI   MS-7350
             2GB RAM - Corsair XMS2 CM2X1024-5400C4
             Seagate 320GB  ST3320620AS
             BIOS AMI  V.2.0   01/31/2007
             Nvidia NForce 650i SLI
             NVidia NForce 430/410 SATA Controller (04/24/2006  V.5.10.2600.666)
    Thanks in advance

    It should do

  • MSI P6N-SLI AND INTEL QUAD CORE Q8200 NOT SUPPORTED ? BIOS FLASH ?

    HI,I have MSI-P6N SLI (MS-7350) pc mainboard and my new processor Intel Quad Core Q8200 not running on this desk.
    It possible some bios update or something ??   :(
    thanks for answers

    Quote from: DaLoona on 02-September-10, 02:46:27
    According to this:
    http://global.msi.eu/index.php?func=prodcpu2&prod_no=1141&maincat_no=1&orderby=cpu_name%20ASC#menu
    "Yorkfield" 45nm quadcores are not going to work on this board, only "wolfdale" 45nm dualcores and even that depends on revision, like Jack mentioned.
    So your Q8200 is a no go unfortunatly.
    Only the older 65nm "Conroe" quads will work.
      and fastest intel processor (not 45nm quad core) ?

  • MSI Eclipse SLI don't detect X-FI on vista x64 sp2, but XP detect it right

    Why my X-Fi Extreme Audio detect as High Defenition Audio in windows, but in Everest it detect X-FI?
    I can't install drivers for X-Fi. "Supported device not found"

    Quote
    Hell it aint even a real EAX card. Couldn't even activate EAX 2.0 with on my old MSI Eclipse. All the games i tried it on simply said the card did not have EAX capability. What a crock >.<
    Well, you knew what kind of X-FI Card you would get:  A Creative X-FI Extreme Audio.  This is a full featured Extreme Audio Card which has precisely the same features (and limitations (!)) of the retail version of this particular model:
    http://en.wikipedia.org/wiki/Sound_Blaster_X-Fi#X-Fi_Xtreme_Audio
    Quote
    X-Fi Xtreme Audio
    The entry-level model of the X-Fi series, the Sound Blaster X-Fi Xtreme Audio, does not actually have the EMU20K1 chip but is a re-branded Audigy SE, using the same family of chips (CA0106-WBTLF), and even the same drivers.[9] Thus, not only is all of the X-Fi–related processing performed in software, but it also lacks basic hardware acceleration just like the SB Live! 24-bit, the Audigy SE and other budget Soundblaster models. The X-Fi Xtreme Audio does not use the same drivers as the rest of the X-Fi family, some games do not recognize it as being "X-Fi capable hardware", and the device's hardware profile resembles that of older Live! and Audigy cards.
    Furthermore, users have reported that it slows down some applications and games, and that rear sound in games (all) is muffled and of profoundly low quality.[16][17][18] Thus, even if the card is marketed as part of the X-Fi line, it does not belong to it technically, just like the Audigy SE doesn't technically belong to the Sound Blaster Audigy series. The card is not marketed as supporting the "X-Fi Gaming Mode" (but is still marketed as "X-Fi"), and there are no official implicit or explicit statements regarding its having hardware acceleration or not.
    This applies to all X-FI Extreme Audio Cards.  What you are actually saying is:  The card is bad because the card (you knew you were getting) is bad.  This is a tautology of no argumentative value AND it has nothing to do with the board. 

Maybe you are looking for

  • Crystal Report 13 Visual Studio 2010 SQL Server 2008 R2 ODBC Problem

    Hi Everybody, I am new in Crystal Report. I developed a web application in Visual Studio 2010, and my Database is SQL Server 2008 R2. I created reports using Crystal Report 13 in Visual Studio and my Operating System is Windows 7 32-Bit. I used ODBC

  • Trying to understand different file sizes based on publishing options

    Hi, I have a project that when published was coming out with the .swf at about 15.9MB.  This is in Captivate 7.0.1.237 with the following settings (defaults I believe): Compress Full motion  recording swf file - unchecked Retain Slide Quality Setting

  • Calling PLSQL Procedure with CLOB input parameter from JDBC

    Hi.. I've got a PLSQL procedure with a CLOB object as input parameter: function saveProject (xmldoc CLOB) RETURN varchar IS I want to call that procedure from my JDBC Application as... String data = "..." CallableStatement proc = conn.prepareCall    

  • 2 monitors cable

    What kind of cable do you need to hook up a external VGA monitor to my 17 inch imac G5 and can i use my external monitor as the main monitor.

  • How do I get the music on my i pod to my new computer with an empty librar

    I acedently erased all my music on my i pod while I was out traveling, so I filled the ipod with a lot of music from another computer (so I cant just burn the music on to a cd/dvd). Now I have just bougt a new computer and downloaded itunes and I wou