MSI K7N2 Delta ILSR Bios v.7.6 ??When??

Hello,
I just asked myself when MSI is going to publish a new Bios Update above the 7.6 for the K7N2 Delta ILSR mainboard !!! I think it's time for a new Bios update, because of the few problems with this mainboard !!!!

Quote
He has confirmed the ports are present on the board....
I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
this worked, thx a lot

Similar Messages

  • [nForce] MSI K7N2 Delta ILSR; bios, neither windows recognize IEEE1394

    Hello,
    Since 2 years I have used a msi motherboard. Now since I dont have IEEE1394 of an external card anymore (Audigiy), i tried to connect my digital camera with the IEEE1394 to the motherboard. Rebooted my pc, windows doesnt recognize new hardware. i'm going to look in the bios, and see that my bios (bios 7.8) is different from the one explained in the manual (see pic). I tried to downgrade my bios to 7.2, to know if it is the 7.8 version that has the problem. but it was the same, no option for IEEE1394.
    Normally have you this:
    But I dont see this option for the IEEE1394 in my bios....
    Thx in advance for helping me

    Quote
    He has confirmed the ports are present on the board....
    I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
    That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
    Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
    this worked, thx a lot

  • Internet Connection Problem on MSI K7N2-Delta-ILSR

    Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
    Athlon XP 2400+ Overclocked to 2205MHz
    2 memory modules of 256MB 400 manufactured by Samsung
    TharmalTake Volcano 11
    Triplex Xabre 400 PRO with 128MB
    Hercules Gamesurrround Fortissimo III 7.1
    Microcom InPorte Home modem 56k
    Leadtek winfast 2000 (TV/FM radio)
    Acard SCSI controller (Acard AEC-6710D) for my scanner
    WesternDigital WD800 GB
    WesternDigital  15.3gb
    Bios ver.7.4  
    Can anyone help me?

    Quote
    Originally posted by Roger Wilco
    Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
    I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
    I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
    I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
    Anyone else in the same boat?
    Hi,
        Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck  
    Rob

  • Sudden Restarts MSI K7n2 DELTA ILSR

    I've had this setup for about a year now.
    Sudden restarts now plague my system, no virus found per NAV 2004, ran processor burn in wizard, SISOFT sandra, on cpu arithmetic and cpu multimedia setting, 100 cycles (no problems) windows memtest ran with no errors via start up disk full cycle of tests.
    Have reloaded video drivers,to no avail, this happens about once a week, any ideas????
    MSI k7n2 delta ILSR Bios version 7.7
    1.5 Gig Micron PC 3200 (512x3) RAM supporting dual channel stock voltage
    mixed bag o ram, crucial, micron technology, and, patriot
    Athlon xp 2500  stock voltage
    SLK 900A heatsink with 80 mm tornado (temps at idle 35-38c) (42 load)
    Creative SB Live
    Nvidia 256  mb asylum video card GE FORCE USR DATA PCI FAX Modem (V92) 5610b
    Hercules 420W PS
    All drivers are up to date and windows update run regularly (Win XP Pro SP2)
     [/COLOR]

    Quote
    Originally posted by scooter787b
    well for one thing the k7n2 series can only support 2 pc3200 dimms,
    are you really sure ?
    my motherboard which is rather old now supports 3 pc3200 dimms.
    norton antivirus is CRAP.
    i stopped using it when i found my harddrive was full of viruses.
    try avg6 for example which is free.

  • FLASH BIOS MSI K7N2 Delta-ILSR ????????

    I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get  into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
    I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
    Thank you
    My system:
    WinXP Pro
    MSI K7N2 Delta-ILSR
    AMD 2500+
    1 GB DR3200
    Seagate 160 SATA

    http://www.msi.com.tw/html/support/bios/note/ntfs.htm

  • MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

    Hi
    i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
    unfortuntly i can't boot it. it wont show anything on screen.
    i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
    all i get is : 
    blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
    power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
    memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
    cpu: AMD xp 3200+ 400fsb.
    i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
    i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
    i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
    all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
    i also e-mailed MSI support that question. (2 days ago. no answer yet)
    oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
    can you help me? 

    hi guys
    here is my PSU specs:
    Colors-It 500w-Max Silent ATX Power Supply
    Voltage 115/230V
    Current 10A/5A
     Frequency 60/50Hz
    +3.3   +5    +12   -12     -5      +5SB   BLK    GRN    GRY
    30A    50A  15A   1.0A   1.0A   2.5A   COM   P-ON   PG
    connectors:
    ATX-2.03 Connector: 1
    ATX-12V Connector: 1
    CD-Rom/HD 4 Pin connector: 6
    Floppy 4 Pin Connector: 2
    Serial ATA Connector : 1
    cpu: AMD Athlon XP 3200+
    MotherBoard: MSI K7N2 Delta-ILSR   More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
    Memory: kingstone 512mb pc3200 400MHz x2      More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
    i have other brand of memory moduls (micron pc2300) i tried them too. no go.
    i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
    as i said before, i have  pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
    but if mobo not showing bios, i can't update bios from floppy.
    and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
    as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

  • MSI K7N2 Delta ILSR - RAID BIOS Option ???

    hi ho,
    i have my 2 storage devices pluged into the promise 376 onboard controller. they are not connected as a real raid (not mirror nor real stripe). my OS is win2k on the first sata device and everything was fine for a long time.
    but now when my system boots, it detects the ide drives and then i see the irq board.
    right after that the system stops and tells me 'disk boot failure'. so i don`t get the chance to configure my raidcontroller or my sata devices.
    it is as the controller is deactivated. i remember a bios version where you could activate and deactivate the sata controller. but in my bios (right now it is v7.8) there is no such option.
    i have tested so far:
    - reset cmos
    - flash bios v7.5 to 7.8
    - disconnected sata drives
    anyone with similar problems or any suggestion?
    > MoBo : K7N2 Delta-ILSR Bios v7.8
    > CPU   : AMD Barton 2500+ (not overclocked)
    > Ram  : TwinMos 1GB 3200 400Mhz
    > Sata  : 2 x Maxtor 120GB Sata (as single Devices on Raid-Controller)
    > Ide   : 60GB IBM DeckStar
    > Gra  :  ATI 9600 pro 128MB
    > Aud  :  SB Audigy 2 ZS
    > Pow  : SilverPower 350W, +3,3V/+5V@25A and 12V@18A
    > OS    : win 2000 SP4 + Security Updates 31.07.04 + DirectX 9.0c

    watch the bottom of the screen after pressing Enter on the "Welcome to Setup" screen. There will be some moments of files being loaded, and then you should see a message appear which says "Press F6 if you need to install a 3rd party SCSI or RAID driver". This message will only stay on the screen for a couple of seconds, so press F6 as soon as you see it appear. After this is done, you will see other messages appear, and it will act as though nothing is happening, but eventually a screen will appear which will allow you to install the drivers for the sata controller.
    specify a device press S, select "win 2000 promise fasttrak 376 controller" it will read floppy and load, dot not remove floppy yet, continue win2000 install it may nead to access floppy to finish installing raid driver, did you do it like this.
    try making some floppy boot disks and boot to floppy instead of cd.
    http://freepctech.com/pc/002/files010.shtml
    when you say there not listed, where did you see this? they wont be listed, windows will search for fasttrak controller so it will see sata's conected to it with out you knowing, so long as you load the controller from floppy that came with mobo as above.

  • Strange phantom restarts on MSI K7N2 Delta ILSR

    Just wanted to see if I could get opinions on this. My MSI K7N2 Delta ILSR mobo runs real nice now, but still, on occasion, very rare and intermittently, it will just restart. Not likely a heat issue, as the temps are nice and low. Also, not just happenning when I'm playing a game or anything strenuous. Did it once while checking email, once during install of an MS Office program, and once during a game. Could it be my old Gforce 2 MX 200 video card, as the picture sometimes gets wavy (like fine waves on an ocean), and the old computer it was in did similar things, or is it common with this mobo.
    MSI K7N2 Delta ILSR
    Athlon XP 2500+ Barton
    1026 MB Kingston DDR RAM (2x512 Dual)
    Gforce 2 MX 200 AGP 4x
    WD 60 GB 7200 RPM

    I had errors on test 4 not 5 with Winbond 2-512 Dual Channel called Hardcore Cooling and they said that getting errors with memtest86 may not mean that the ram is defective, it may not be compatible with the memory comtrol and they had me RMA it back. I also was not able to run the ram stable at there advertized rate of 6 2 2 2 it was only stable at 8 3 3 2.5
    I replaced it with OCZ after talking to there Tech support people about compatiblety problems with the Nvidia chipset. Sense I installed the OCZ I only had one ram reboot and when I checked I was running the voltage at 2.5 and OCZ said that I should be running at 2.6. They also said that I could run it up to 2.8 with no worry.
    Look on manufactor web site to see what ram timing yours should be running at and what voltage, Auto setting in Bios is not always the best setting.
    If it still not stable at manufactor spec than I'd talk to who ever you bought it from about replacing it or refund and buy something thats on the Nvidia compatible list.
    Most ram manufactors have a list of motherboards that there ram will work on but sometimes the newer boards like K7N2 or not listed yet as still working that out.

  • Kate needs HELP!!! MSI K7N2 Delta ILSR

    Guys...
    pls help me...
    I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
    I installed everything assembled it... booted and loaded fine for about 3 times...
    and suddenly....
    >power on
    >no video
    >no beeps
    >after checking hard nothing happens...
    >only thing I can tell is that the d bracket is indicating "memory section"
    ....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
    Why woudl a memory suddenly not work?
    I know I was adjusting bios for this and that....  
    I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
    COuld it be the mobo or memory or the video card???
    pls help....
    My email is [email protected]...
    please please help...
    and guys in MSI what is your expert opinion? mobo? or memory?
    Heeeeeeeeeeeeeeeellllp...
    thanks...
    Kate x

    hi and welcome to this forum.
    nice to se a girl here for a change
    clear cmos jumper jbat1.
    also try safe mode jumper j10 ans j11.
    also try to reseat memory and dont trust the dbracket to 100%.
    it can show wrong sometimes.
    Quote
    COuld it be the mobo or memory or the video card???
    when you got it running then run http://www.memtest86.com to check memory,
    also what psu do you have ?
    post max amps on 3.3v 5v and 12v rails.
    minimum is 28 35 16.recommended is higher.

  • Data corruption on MSI K7N2 Delta ILSR

    Hi all,
    Just got my new MSI K7N2 Delta ILSR up and running.
    Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum  )
    While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
    Then the overclocking began   I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
    I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
    Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
    When using an FSB of 166mhz no data corruption or crc errors.
    What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
    Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
    The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
    Help!  
    gr,
    Remco

    Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended  
    Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
    Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
    Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome  
    gr,
    Remco

  • MSI K8T Neo2 F vs. MSI K7N2 Delta ILSR

    Hi there !
    I have an amd Athlon XP 3200+ overheating problem, and contacted the technical support of the shop where the processor and CPU was coming from.
    Since they do not have any XP 3200+ to replace mine, they propose me to replace fro free :
    - the XP 3200+ by an AMD Athlon 64 3200+
    - my actual MSI K7N2 delta ILSR by an MSI K8T Neo2 F
    ... and this for free.
    Since I do not know this new motherboard that has been proposed, I'd like to have advice on if this is a good deal ?!?
    My actual system has :
    - an Aluminium case with 2x 12cm FAN's
    - 2 IDE hard drives
    - 1 SATA hard drive
    - TWINX Corsair XMS 2x256MB PC 3200L (Extreme low latency)
    - an AGP 8x video card
    - An Antec True Power 480W.
    will the new motherboard fit with this configuration?
    Many thanks for your input !

    Not really, unless you really want to oc your cpu. The K8T boards aren't that good in OC-ing. But still, some is possible and you'll be sure that the board is as steady as a rock.
    For a moment I thought you were talking about a Neo board ... but I just saw it's a Neo2. That means Socket 939 -> dual channel RAM.
    The only risk you have now, is that your RAM won't work in dual channel with the CPU. But that's not really a board-problem, more a CPU/RAM-controller related problem. But then, it's still a great offer and chances are good that it will work. If you run into any trouble, RAM-related, just flash bios to version 1.9 and you will probably be just fine.

  • Msi k7n2 delta ilsr problem

    hi i have this configuration on my pc:
    antec true control 550 watts
    msi k7n2 delta ilsr
    kingston hyper x pc3700 2x512 mb
    athlon xp 3200+
    seagate 120 gb sata 7200.7 hd
    ati radeon 9800 pro excalibur ice q
    i have 2 problems : the first one is that sometimes windows display me a blue screen with certain problem related to ati2dg.dll i think that problem is beacause the video card so i decided to update the bios , in the live update page from msi says that the bios 7.6 fix a bug with ati vga cards but after flashing and updating to bios v7.6 that blue screen with the same error still appearing so i dont know what else to do to solve the problem and the second one is that when i start any game or make the processor to work a little mostly related with video stuff the case speaker start to beep and the pc lags until he restarts with no reason i really dont know why if u can help me thank you

    Foxtrotccs,
    In the BIOS try setting the AGP to 4X and disable Sidebanding. Then set the AGP Apeture to 256. See if that helps.
    Make sure you are running the lastest   nVidia nForce Drivers and the latest ATI Catalyst Drivers
    Take Care,
    Richard
    P.S. There is still a possibility that the Kingston RAM is the problem.

  • MSI K7N2 Delta ILSR Memory problems

    I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours.  The main system components are as follows:
    Motherboard:  MSI K7N2 Delta ILSR
    CPU: AMD Athlon XP 2800+
    Memory: 2x512 OCZ PC3200 EL
    My problem is that the burn-in software continues to freeze up during the memory test.  I've already contacted the software manufacturers and the software is stable.  It's a problem with the way the motherboard handles the memory.  I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS.  The SPD settings are 2.5-3-3-7.  Right now I have them at 3-4-3-8.  It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours.  Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted.  I can say that after 7 hours, it wasn't showing any slowdown in performance.  If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

    Thanks for the suggestions.  The CPU FSB is 200, so it's already matched up there.  And we have a ton of fans already.  There are two in the front, 4 inside and 1 on the back.  It's a custom case, 2u high.  The power supply is oversized and more than adequate to provide the required power.  I have four of these units running right now.  Two with 2x512 sticks and two with 1x1024 sticks.  For each combination, the memory clock speed for one is 166 and 200 for the other.  I have been loosening up the memory timings trying to get the system stable, but it still isn't.  If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system.  Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory.  Thanks.

  • MSI K7N2 Delta-ILSR Dead? Help!

    Hey all,
    Well, the other day I was on my computer playing a game when my mobo fan started making an odd noise (as if switching rpm), so I took off the side of my case and took a look inside. Everything seemed to be functioning properly, then I switched my cpu fan speed via the pci slot speed control. As I switched from High-Medium-Low, I noticed that the fan actually slowed to the point where I could see the blades spinning, at least for a second or so. I found that rather odd, seeing as how I've never seen a fan (especially a cpu fan) slow to the point that I could see the blades spin. Anyway, a couple of hours later, I shut down and went to sleep.
    The next day I had my comp on for about maybe 30mins to an hour or so when suddenly I heard an alarm from the computer speaker, so I was like, ":censored:?" since I had never heard it before. It was evidently the temperature warning, which I had set to 70C. So I shut down within 15 seconds and opened up the side of my case.
    I noticed that the cpu fan wasn't moving at all (usually I'd open the case in time to see the spin-down). So I turned the computer back on and the fan didn't budge, so I immediately powered down, assuming that the CPU Fan had died. Later on, I hooked the fan itself up to a free power cord in my sister's computer and booted up, along with the speed controller, flipping from medium to high to low without any problems.
    I then did screwed the fan back to the heatsink in my comp and booted up. I went into the bios an noticed that the rpm was 8k, which is way too high for my fan (normally 5k). So i began switching from high, medium, to low once again, then I saw that the rpm reader in the bios went to 0. So I looked back in the side of my case and saw that the cpu fan was once again dead. At this point I concluded that it was the fan and was about to order the Volcano 12.
    A day later I placed the fan inside my sister's computer on a free cord, yet again, and yet again, it worked fine.
    I once again put it in my computer to test and this time it worked fine, even while switching between speeds. Unfortunately, I then noticed that the mobo fan was not moving, then began to move.
    Well, I'm guessing now that it's simply the motherboard that has a short, since both the motherboard fan as well as the cpu fan have randomly been dying the past few days. The motherboard fan; however, has switched rpm many times in the past from 5k to 3k.
    It could also be a PSU problem, but I have Antec 400watt psu and it's been working fine for the past 2 years, so I doubt it. I've had the motherboard for a little over a year. I upgraded my cpu from 2200+ to 3000+ in July. That's also when I bought the cpu fan. The motherboard fan began fluctuating in rpm noticeably back in April or May of this year.
    Yesterday, I used the computer again and had it on for about 2 hours or so and I had speedfan monitoring the temps and the rpm. The temps stayed relatively stable: 48 cpu, 44 mobo.
    But alas, the RPMs were totally [blame me for the swear filter] up. At one point, both the mobo and cpu fan speeds were reading 0, even though both continued to spin within the case and the temps remained the same. Then after 30mins or so, they cpu fan began reading again at 40,000-42,000rpm, which is obviously incorrect, seeing as the fan is rated for around 5k. I got/get the same readings in the bios, both fans reading at 0rpm as they continue to physically spin.
    Also, during a number of times that I've started up the comp within the past few days, the motherboard northbridge fan wasn't spinning at all and didn't begin to until a few minutes into my windows session.
    Also, I took out the NB fan and noticed a slight crack in the back of it.
    I was considering simply just buying the Volcano 12 and the MSI K7N2 Delta2 Platinum rather than RMAing the mobo. Then perhaps an Antec 550W psu, if necessary.
    Any ideas what I should replace and in which order? And has anybody else encountered any similar problems with this mobo (at least with the mobo rpm, which has been a prob for about 6months on and off)?
    I bought the mobo along with a 2200+ in July of 2003. I upgraded the ram from 256 to 512 in April 2004 (which is around the time I started hearing rpm probs with the mobo fan) and I upgraded the cpu in July of 2004
    Many Thanks!  
    My Specs are as follows:
    Windows XP Professional SP1
    Antec SX1040B2 File Server Case
    400watt Antec PSU
    MSI K7N2 Delta-ILSR
    AMD Athlon XP 3000+ (2.17GHz)
    Thermaltake TR2 M2 HSF
    Kingston 256MB of PC2700 DDR-333MHz RAM
    Generic 256MB of PC2700 DDR-333MHz RAM
    ATI All-In-Wonder 9800 Pro
    Sound Blaster Audigy 2ZS Platinum
    Pioneer 10x DVD Drive
    Sony 8x Double Layer DVD-+RW
    Western Digital 120.0GB 7200RPM HD ATA/100
    Western Digital 120.0GB 7200RPM HD ATA/100
    nForce Ethernet Adapter w/Cable line
    Logitech MX500 Optical Mouse
    Logitech Elite Keyboard
    19" Envision Monitor EN985e
    Logitech Z-680 5.1 Speakers

    Could be a fluctuating PSU that's breaking down power to the MB. You have a whole lot of components dragging that PSU down. With what you have in your rig I would run either an Antec or Enermax 550W. Best way to be sure is to borrow a PSU or buy one from a store with a good return policy so that you can return it if indeed it turns out to be the MB. If I don't have your board here on my bench to test the only thing I can suggest to you is to swap out components unfortunately.

  • MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chip

    I tried to install 3 of the Crucial Ballistix Tracer (1 Gig Each) in this motherboard (MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chipset) and it will not run stabilly no matter what I tried. Is this a bios conflict with the memory? If so, are there any new bios updates? I have tried cas settings and voltage settings but nothing works. It will how ever run perfectly with only 2 sticks in single channel mode. It will not run same 2 sticks in dual channel mode. Anyone have any ideas? Anyone know of any new motherboards with maybe NFORCE 4 Chipset that support all 3 sticks of this memory and an AGP graphics card? Im thinking of a new motherboard but I still need to have AGP and SATA.
    Barton 3200 core proc.
    System has ran fine for a solid year until I tried new memory. Please help!

    Quote from: freakytiki4u on 07-November-06, 23:42:33
    Ok I tried to use relaxed FSB by -10 and relaxed mem timings but still unstable due to the motherboard trying to use dual channel memory. If you can modify the bios to where it will not have the capability of dual channel memory I truly believe it will work. Will u try this for me? I would greatly appreciate it as I am really not ready to spend all the money on new equipemtn when this suits my needs for now.
    sure but as i said before this is gona be experimental and risky. Here we go:
    MSI K7N2 Delta ILSR Experimental MOD E1(Disable Dual CH ability)
    Procedure is automated in best possible safest way to BIOS update.
    Prepare a blank diskette in a good condition(newest one etc.)
    ]execute file under XP will make bootdisk with automated BIOS update procedure. when diskette is ready, reboot PC and boot from FDD(floppy), wait a bit, then you will be asked for final confirmation about BIOS update process, press a key to proceed, after BIOS update is complete, ensure that you got successfully output message from flash program. then power down your PC, remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
    pull back power cord, power up your PC, when you see CMOS checksum error,(expected msg) hit F1 to continue to re-build DMI pool data, then reboot and enter in BIOS, LOAD BIOS DEFAULT, and SAFE AND EXIT.
    NOTE: Ensure your PC is stable before proceed with BIOS update.
    NOTE: Use it at own risk, chance of failure is big, cannot guarantee results and safest as provisional mode which can guarantee it will work stable with features. also cannot test it personally before give you. (don't have mobo anymore)
    Using it may end with dead mainboard (BIOS chip re-flash will be required, if somethink goes wrong)

Maybe you are looking for