MSI K7N2 Delta ILSR Memory problems

I'm trying to burn in a system in a 50 deg C (122 deg F) room for a minimum of 12 hours.  The main system components are as follows:
Motherboard:  MSI K7N2 Delta ILSR
CPU: AMD Athlon XP 2800+
Memory: 2x512 OCZ PC3200 EL
My problem is that the burn-in software continues to freeze up during the memory test.  I've already contacted the software manufacturers and the software is stable.  It's a problem with the way the motherboard handles the memory.  I've tried putting the memory in dual channel configuration and changing the timing settings in the BIOS.  The SPD settings are 2.5-3-3-7.  Right now I have them at 3-4-3-8.  It's a lot more stable than it was under the default settings but it still freezes up sometime after 7 hours.  Unfortunately, I wasn't around when it froze so I don't know exactly how long it lasted.  I can say that after 7 hours, it wasn't showing any slowdown in performance.  If anyone could think of anything else I might be able to do to get the system stable, I would greatly appreciate it.

Thanks for the suggestions.  The CPU FSB is 200, so it's already matched up there.  And we have a ton of fans already.  There are two in the front, 4 inside and 1 on the back.  It's a custom case, 2u high.  The power supply is oversized and more than adequate to provide the required power.  I have four of these units running right now.  Two with 2x512 sticks and two with 1x1024 sticks.  For each combination, the memory clock speed for one is 166 and 200 for the other.  I have been loosening up the memory timings trying to get the system stable, but it still isn't.  If the power supply is good, and I'm unable to cool the system anymore due to limititions within the case, is there anything you can think of to stabilize the system.  Maybe other settings in the BIOS or suggestions on how to go about getting good timings for the memory.  Thanks.

Similar Messages

  • MSI K7N2 Delta-ILSR MB Problems, Need Help ASAP!! PLEASE

    Ok  I just got this motherboard (MSI K7N2 Delta) Yesterday and after getting it setup I began overclocking the Processor (an AMD Athlon XP Barton Mobile 2500+) I was at 11x 215 1.750V Perfectly. I moved to 216 it started to seem unstable so I pushed the VCORE up to 1.775 and tried 217. It couldn't boot so I dropped it back down and decided ok 208 and a 11.5 multi might get me past the 2.4 mark which I was looking for. Well when I changed the Multi. to 11.5 and said save the system just sate as the flashing y for save. I could not change it to n I had already pushed enter So i firgured great and left it alone for a few minutes, nothing so I reset it. Now it refuses to boot/post. It spinds the fans the HD's the Network port is going but I get no picture. I have cleared the CMOS using the jumper I have removed the battery and power for over an hour and I still get nothing. I am assuming this is a BIOS error but I am not sure what to do to fix it. Does anyone here kno maybe, something I have yet to try something I can do? I would hate to RMA it and have to wait on newegg. Hell the thing is a day old. So please any idea's are welcome I have this posted on the Hard Forums as well but I am hopinh this forum may be more popular with getting help as no one is helping over there. Thanks!

    Hi,
    Cross: Just in case you are doing something wrong there's a clear CMOS guide here, follow it to the letter (and don't forget to put the FSB jumper to SAFE beforehand - there's a note about it in the guide).
    How To Clear the CMOS
    Your system board or CPU maybe not be dead yet - I had a similar problem with one of my boards and I tried everything - to cut a long story short I eventually got it working!!!
    Btw, If you can't boot or get into the BIOS put your other CPU in (clear BIOS again after fitting!), so that you can prove whether your motherboard is working correctly!  
    Good luck!   I'm off ta bed!
    Axel  

  • K7N2 Delta ILSR memory problem

    I have a K7N2 Delta ILSR board with Athlon XP 2500 with 2 Gig of Mushkin Black Line ram (the ones that are
    suppose to be CL2). I change the FSB to 200, and my memory won't run at CL2. Want to raise the Dram voltage
    to 2.8V to see if it would make a difference. I looked all over this site for the modded bios 7.8. Does anyone
    have the modded bios??? Any help would be appreciated.......

    He/She overclocked the 2500+, to make it become a 3200+. Done it myself, but it mostly works with the first step of the 2500+. - That means the overclock forum. 
    Well, CAS 2 is a very tight timing, which I don't think is possible. In general on Socket A systems:
    - FSB 133/266 --> CAS 2 or 2.5
    - FSB 166/333 --> CAS 2.5
    - FSB 200/400 --> CAS 3

  • MSI K7N2 Delta-ILSR, Mouse problem & Video off problem solved!!!

    I find the following information that I collected very interesting at the very least...
    Here goes...
    The video off problem that I was having was directly linked to the mouse. Here, let me explain the video off problem. In the BIOS Have the Standby mode set to S3. The problem occurred when I started windows, then went into standby, then started back up, then restarted the computer, the monitor would act as if it were in sleep mode, or rather there was no signal being sent to the monitor. Well the odd way I fixed that is by plugging in a standard 2 button PS/2 mouse. Also this fixed the issue with the mouse sometimes not working in windows.
    Here is how I tested.
    Logitech MX700 Cordless Optical Mouse, PS/2 & USB= failed.
    Logitech iFeel Optical Mouse, USB= failed.
    Microsoft Cordless Ball Mouse, PS/2= failed.
    Standard Artec (Cheapy brand) Ball Mouse (With no wheel), PS/2= All issues fixed, and passed.
    When I said failed I do not mean they didn't work, I mean they sometimes didn't work and also caused the Video off problem after restarting the computer.
    Obviously it isn't the ports (PS/2 or USB) that are the problem, it is more like the mouse itself, and the amount of buttons in particular. As you can see above the only mouse that works correctly is the one that only has 2 buttons, the rest has 3 or more buttons along with a Wheel. The MX700 has 8 buttons + wheel, WOW!
    Anyways I figure out it was the mouse, and not the memory.
    Obviously MSI needs to make a patch for this mouse problem.
    I'm still having a hard time believing that the mouse caused the video not to work, but it is true! I spend well over 5 hours testing this crap. Every time with the mice with more then 3 buttons it messed up, and every time with the 2 button old fashion mouse it worked flawlessly!
    MSI, get to work on a new BIOS to fix this mess!!!  :]
    BioHaz

    Quote
    Originally posted by Raven_
    hi
    its possible to use an ps/2 mouse AND a usb mouse at the same time.
    i used the ps/2 mouse in windows and the usb mouse when playing games.
    you can get some trouble if you do it the way i did it.
    i was in windows surfing and the pointer just jumped all over the screen.
    when i looked on the other side under a table a friends little kid played with the usn mouse.  )
    bye
    LOL, that isn't what I'm talking about.
    There seems to be a problem with my motherboard accepting mice with more then 2 buttons. It works the first time, but if you restart the computer, the video goes off. If you have both installed, it still messed up.
    BioHaz

  • MSI K7N2 Delta-ILSR Power problem?!

    So I worked all last night trying to fix the damn thing. It wants to keep powering off on its own. So I unplugged all the devices from the board and powersupply except the only needed items, the board, power switch, and memory (cpu fan of course left on). Still turns off. Reset bios, still. Put system into safe mode by the jumper. Still.
    Okay so I gave up, and took the board, memory and processor into a local place that sells these boards. They have seen a few problems with them. 4 hrs later, $55 short they tell me the heat sink wasn't on the chip right so it caused the board to think it was hot and shut itself down right away! He said he ran it for most of the day. So I am like whatever! He left it on there how he had it. I took it home, hooked it back up, and there it goes again!
    The 1st night it ran fine, no hd, but I ran it the whole evening. The 2nd night I powered it up, it started to do this. Nothing changed. So now I am getting ticked off. I am about to take my whole case, and system back to those guys and tell them see....
    Anyone who has used this board have any ideas? I have built many systems and this is the first one that is being a pain in the butt.
    PowerMAX 400w powersupply.
    LP-8800D MODEL #

    Powersupply was brand new and came with the case. :(
    Quote
    Originally posted by twistedbrowntucker
    Quote
    Originally posted by rzotz
    What I am noticing is that when it sits for 10-15 min, and I try to turn it on again, it takes a little longer before it turns off.  It actually may stay on up to 5 sec, then turn off.  But if I try again a few times in a row, maybe .5-1 sec it cuts off.  I have already reseated the heatsink on the processor again.
    Powersupply is rated at:
    +12v - 25amps
    +3.3v - 28a
    +5vsb - 2.0a
    Power supplies can go bad at anytime.Take the whole thing up there.Case and all and let them check it out.BTW all power supplies aren't equal. IMHO buy an Antec TruePower 430 or 480 watt

  • Internet Connection Problem on MSI K7N2-Delta-ILSR

    Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
    Athlon XP 2400+ Overclocked to 2205MHz
    2 memory modules of 256MB 400 manufactured by Samsung
    TharmalTake Volcano 11
    Triplex Xabre 400 PRO with 128MB
    Hercules Gamesurrround Fortissimo III 7.1
    Microcom InPorte Home modem 56k
    Leadtek winfast 2000 (TV/FM radio)
    Acard SCSI controller (Acard AEC-6710D) for my scanner
    WesternDigital WD800 GB
    WesternDigital  15.3gb
    Bios ver.7.4  
    Can anyone help me?

    Quote
    Originally posted by Roger Wilco
    Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
    I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
    I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
    I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
    Anyone else in the same boat?
    Hi,
        Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck  
    Rob

  • MSI K7N2 Delta-ILSR (MS-6570) BSOD problems grrr

    I recently purchased this board and although it is an awesome product, I'm having a problem with BSOD's when I play a game for a certain period of time
    Specs:
    MSI K7N2 Delta-ILSR  (7.6 BIOS)
    AMD Athlon XP 2800+ Barton
    512MB (2x256MB) Samsung PC-2700 DDR memory (2.5-3-3-6 1T)
    MSI 128MB GeForce4 Ti 4200 (4X AGP)
    NVIDIA nForce on-board sound
    Western Digital 80GB drive w/ 8MB cache
    MSI X48 CD/CD-RW/DVD combo drive
    Windows XP Professional SP1
    PSU:
    Turbolink 420watt (came with case)
    +3.3V is 28A
    +5V is 40A
    +12V is 18A
    So what happens is I get a STOP error during the game that shows the kmixer.sys driver as the culprit. Sometimes it's accompanied by PAGE_FAULT_IN_NON_PAGED_AREA too. I read somewhere that kmixer.sys has to do with windows audio and that it's a 3rd party driver issue or a memory issue. I'm using the latest NVIDIA 3.13 nForce platform drivers. I ran Memtest lastnight for 12 hours straight and 0 errors. I'm thinking the memory may not be compatible with the board nor dual channel, is this possible? I have also tried several different drivers for both video and chipset including MSI's own and I still get the kmixer.sys BSOD when playing games. My previous motherboard was an MSI KT3 Ultra2-R (MS-6380E) which I had no issues with. Any help would be greatly appreciated. Thank you in advance.
    --Update--
    I just tried to play a game with audio disabled and it crashed this time with DRIVER_IRQL_NOT_LESS_OR_EQUAL with nv4_mini.sys as the problem. My IRQ table shows some sharing, but device manager shows no conflicts.

    Ok I tried running the DTM-CB3 module which is nForce2 approved at 3-4-4-11 2T timings and experienced the same result even at 2.6 and 2.7v. I tried both in dual-channel and same thing happened. However, I downloaded a program called Prime95 and ran the CPU torture test and the system returned a fatal error within the first few minutes. CPU Temp was at 57 C and the warning beep (set to 60C though) sounded intermittentley which is strange. I let it cool down then ran the torture test again and about 5min. later the system either seized completely or the program crashed. IE has also crashed randomly on me. I did this several times, before trying a different FSB/DRAM ratio. So I left the system at 200 FSB and used a 6:5 ratio so my memory was running at DDR333 and processor was a 3200+. I ran Prime95 again and the system locked up just as it did the other times.  So after I did this a few times with consistent results. I went back and set the FSB to 166 and tried a 5:6 ratio so the memory was DDR400 and processor was the normal 2800+. I ran it again and to my suprise it passed all the tests and after an hour of this, I tried a game and that was perfectly fine as well. I checked the temps and CPU was only 45 C this time. So I'm thinking the processor can't handle anything above 50C or it's just plain overheating. I ordered a Thermaltake Silent Boost HSF today which is tested up to 3400+ so this should fix my problem. If not, then I'm going to replace the memory with a 512MB Geil PC3200 golden dragon dual-channel kit.

  • Msi k7n2 delta ilsr problem

    hi i have this configuration on my pc:
    antec true control 550 watts
    msi k7n2 delta ilsr
    kingston hyper x pc3700 2x512 mb
    athlon xp 3200+
    seagate 120 gb sata 7200.7 hd
    ati radeon 9800 pro excalibur ice q
    i have 2 problems : the first one is that sometimes windows display me a blue screen with certain problem related to ati2dg.dll i think that problem is beacause the video card so i decided to update the bios , in the live update page from msi says that the bios 7.6 fix a bug with ati vga cards but after flashing and updating to bios v7.6 that blue screen with the same error still appearing so i dont know what else to do to solve the problem and the second one is that when i start any game or make the processor to work a little mostly related with video stuff the case speaker start to beep and the pc lags until he restarts with no reason i really dont know why if u can help me thank you

    Foxtrotccs,
    In the BIOS try setting the AGP to 4X and disable Sidebanding. Then set the AGP Apeture to 256. See if that helps.
    Make sure you are running the lastest   nVidia nForce Drivers and the latest ATI Catalyst Drivers
    Take Care,
    Richard
    P.S. There is still a possibility that the Kingston RAM is the problem.

  • Strange phantom restarts on MSI K7N2 Delta ILSR

    Just wanted to see if I could get opinions on this. My MSI K7N2 Delta ILSR mobo runs real nice now, but still, on occasion, very rare and intermittently, it will just restart. Not likely a heat issue, as the temps are nice and low. Also, not just happenning when I'm playing a game or anything strenuous. Did it once while checking email, once during install of an MS Office program, and once during a game. Could it be my old Gforce 2 MX 200 video card, as the picture sometimes gets wavy (like fine waves on an ocean), and the old computer it was in did similar things, or is it common with this mobo.
    MSI K7N2 Delta ILSR
    Athlon XP 2500+ Barton
    1026 MB Kingston DDR RAM (2x512 Dual)
    Gforce 2 MX 200 AGP 4x
    WD 60 GB 7200 RPM

    I had errors on test 4 not 5 with Winbond 2-512 Dual Channel called Hardcore Cooling and they said that getting errors with memtest86 may not mean that the ram is defective, it may not be compatible with the memory comtrol and they had me RMA it back. I also was not able to run the ram stable at there advertized rate of 6 2 2 2 it was only stable at 8 3 3 2.5
    I replaced it with OCZ after talking to there Tech support people about compatiblety problems with the Nvidia chipset. Sense I installed the OCZ I only had one ram reboot and when I checked I was running the voltage at 2.5 and OCZ said that I should be running at 2.6. They also said that I could run it up to 2.8 with no worry.
    Look on manufactor web site to see what ram timing yours should be running at and what voltage, Auto setting in Bios is not always the best setting.
    If it still not stable at manufactor spec than I'd talk to who ever you bought it from about replacing it or refund and buy something thats on the Nvidia compatible list.
    Most ram manufactors have a list of motherboards that there ram will work on but sometimes the newer boards like K7N2 or not listed yet as still working that out.

  • Data corruption on MSI K7N2 Delta ILSR

    Hi all,
    Just got my new MSI K7N2 Delta ILSR up and running.
    Got some issues with the memory running at 200mhz while the Barton core of my Athlon Xp 2600+ was running 166mhz, this had to be 1:1 (thx forum  )
    While running the default bios settings with cpu/mem at 166/166 fsb everything is stable as hell. I have been running Prime95 for 2 days now and using the system for dvd ripping/encoding, UT2004 gaming etc.
    Then the overclocking began   I'm using the standard AMD cooler that came with my boxed Xp2600+ so I didn't expect an FSB of 200mhz.
    I stopped at an FSB of 190mhz...been crunching Prime95 for 18 hours now and again very stable.
    Now comes the problem : Sometimes I get crc errors when installing a game or decrypting a dvd!! But how can this be? Prime95 is stable at this 190fsb overclock.
    When using an FSB of 166mhz no data corruption or crc errors.
    What can this be? It's not the cables because they're all the same as in my old setup which was running (ahum...walking) stable. PCI/AGP speeds are locked when overclocking...
    Only thing I can think of is the power supply. I've read in a warning post from Bas that the Q-Tec 550w psu I have is crap. So my guess is PSU, but maybe it's something else I'm forgetting...Any suggestions??
    The stupid thing is when I'm not overclocking I don't have the data corruption problems, but I'm still using the same crappy Q-Tec 550w PSU.
    Help!  
    gr,
    Remco

    Hmmm, that's curious. On the MSI K7N2 Delta ILSR product page Kingston memory is recommended  
    Ok, did a Memtest86 v1.11 pass at cpu/dimm 166/166 - no problems whatsoever. I think using Prime95 would have revealed memory problems...but will do another pass with cpu/dimm at 190/190.
    Can overclocking affect the Promise Raid Controller?? It should be locked like the PCI/AGP but who knows...
    Well, I still have to replace my PSU but I'm not 100% sure that this is the problem. What PSU would you recommend? ...and I'm also thinking about replacing the standard CPU cooler, any advice is welcome  
    gr,
    Remco

  • MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

    Hi
    i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
    unfortuntly i can't boot it. it wont show anything on screen.
    i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
    all i get is : 
    blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
    power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
    memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
    cpu: AMD xp 3200+ 400fsb.
    i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
    i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
    i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
    all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
    i also e-mailed MSI support that question. (2 days ago. no answer yet)
    oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
    can you help me? 

    hi guys
    here is my PSU specs:
    Colors-It 500w-Max Silent ATX Power Supply
    Voltage 115/230V
    Current 10A/5A
     Frequency 60/50Hz
    +3.3   +5    +12   -12     -5      +5SB   BLK    GRN    GRY
    30A    50A  15A   1.0A   1.0A   2.5A   COM   P-ON   PG
    connectors:
    ATX-2.03 Connector: 1
    ATX-12V Connector: 1
    CD-Rom/HD 4 Pin connector: 6
    Floppy 4 Pin Connector: 2
    Serial ATA Connector : 1
    cpu: AMD Athlon XP 3200+
    MotherBoard: MSI K7N2 Delta-ILSR   More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
    Memory: kingstone 512mb pc3200 400MHz x2      More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
    i have other brand of memory moduls (micron pc2300) i tried them too. no go.
    i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
    as i said before, i have  pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
    but if mobo not showing bios, i can't update bios from floppy.
    and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
    as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

  • MSI K7N2 Delta ILSR (MS 6570) trouble With ATA card

    Hi, i have major trubble.
    Ihave two 300gb, two 120gb and two 80gb harddrives + 1 DVD burner and 1 CD burner with ultra DMA 100 PCI card and it works fine without using the sata or ide3 raid function. I purchased an new PCI ATA 133 card and the system won't boot. I have tried for an long time to get the raid function to work but wihtout results with my old ATA 100 card (it works when i unplugg the ide cable from ide3).
    Is there anybody that knows with type off PCI ATA 133 card that works or how too coop whith this problem.
    I've got the latest bios ver. 7.8 but no difference
    AMD XP2800+
    Kingston 2x512mb
    ATI Saphire Radeon 9600pro 256mb
    Soundblaster Live Value
    XP pro sp2
    MSI K7N2 Delta ILSR (MS 6570)

    I went to JME-Data and purchased an
    True430
    ATX 430 Watt Power Supply with PFC
    For AMD™ and Intel® systems including
    Pentium® 4
    Dedicated output circuitry
    Voltage feedback
    Antec Low NoiseTechnology
    AQ3 - Antec 3 year parts & labor warranty
    True430 is a 430 Watt 6-output, dual fan-cooled ATX12V (Baby AT or PS/2 Size) power supply designed for personal computer or industrial applications.
    Its ATX12V compliance allows its use with the latest Pentium 4 processors while its backward compatibility ensures its usability with any ATX-based AMD™or Intel® system
    The prise 1099:-
    And everything works great, Thank you very much for the tip. :-)
    No more blue screen and it even works with my memory Kingston Value Ram 2x512 ddr400.
    Is it possible to change the FSB from 166 to 200, and what should i think about before action. Like i said before i have an xp2800+
    Alltså är det möjligt att få cpu gå på samma frekvens som minnena om man ökar FSB har några tip så är jag tacksam.
    Att en nätdel kan göra så mycket helt otroligt TUSEN TACK för hjälpen till och med cpu tempen har sänkts från ca 56 till 46 grader fattar ingenting.

  • Kate needs HELP!!! MSI K7N2 Delta ILSR

    Guys...
    pls help me...
    I am assembling, yes I know I am a techi girl...., msik7n2 with radeon9600 and 2xCorsair Value Select 256Mb DDR 400Mhz PC3200 mem...(hence 512mb)
    I installed everything assembled it... booted and loaded fine for about 3 times...
    and suddenly....
    >power on
    >no video
    >no beeps
    >after checking hard nothing happens...
    >only thing I can tell is that the d bracket is indicating "memory section"
    ....d-bracket from MSI K7N2 Delta ILSR is 1,3,4 red and 2 green. Which is according the the manual "Memory Detection Test"-if the memory module is damaged or not installed properly.
    Why woudl a memory suddenly not work?
    I know I was adjusting bios for this and that....  
    I think just before this happened.. I adjusted something on agp setting... but what ahs that got to do with memory?
    COuld it be the mobo or memory or the video card???
    pls help....
    My email is [email protected]...
    please please help...
    and guys in MSI what is your expert opinion? mobo? or memory?
    Heeeeeeeeeeeeeeeellllp...
    thanks...
    Kate x

    hi and welcome to this forum.
    nice to se a girl here for a change
    clear cmos jumper jbat1.
    also try safe mode jumper j10 ans j11.
    also try to reseat memory and dont trust the dbracket to 100%.
    it can show wrong sometimes.
    Quote
    COuld it be the mobo or memory or the video card???
    when you got it running then run http://www.memtest86.com to check memory,
    also what psu do you have ?
    post max amps on 3.3v 5v and 12v rails.
    minimum is 28 35 16.recommended is higher.

  • FLASH BIOS MSI K7N2 Delta-ILSR ????????

    I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get  into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
    I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
    Thank you
    My system:
    WinXP Pro
    MSI K7N2 Delta-ILSR
    AMD 2500+
    1 GB DR3200
    Seagate 160 SATA

    http://www.msi.com.tw/html/support/bios/note/ntfs.htm

  • Sudden Restarts MSI K7n2 DELTA ILSR

    I've had this setup for about a year now.
    Sudden restarts now plague my system, no virus found per NAV 2004, ran processor burn in wizard, SISOFT sandra, on cpu arithmetic and cpu multimedia setting, 100 cycles (no problems) windows memtest ran with no errors via start up disk full cycle of tests.
    Have reloaded video drivers,to no avail, this happens about once a week, any ideas????
    MSI k7n2 delta ILSR Bios version 7.7
    1.5 Gig Micron PC 3200 (512x3) RAM supporting dual channel stock voltage
    mixed bag o ram, crucial, micron technology, and, patriot
    Athlon xp 2500  stock voltage
    SLK 900A heatsink with 80 mm tornado (temps at idle 35-38c) (42 load)
    Creative SB Live
    Nvidia 256  mb asylum video card GE FORCE USR DATA PCI FAX Modem (V92) 5610b
    Hercules 420W PS
    All drivers are up to date and windows update run regularly (Win XP Pro SP2)
     [/COLOR]

    Quote
    Originally posted by scooter787b
    well for one thing the k7n2 series can only support 2 pc3200 dimms,
    are you really sure ?
    my motherboard which is rather old now supports 3 pc3200 dimms.
    norton antivirus is CRAP.
    i stopped using it when i found my harddrive was full of viruses.
    try avg6 for example which is free.

Maybe you are looking for

  • Voice Memos will not start recording.

    I can pull up the application, but when I tap the record button, nothing happens. The little dial that says "VU" doesn't move, the red recording circle symbol doesn't change to a pause or stop button. Is this an application error? Any suggestions?

  • Updating to iOS 7.2 iPhone 4S, no working iPhone anymore

    Hi guys, Yesterday appeared a notification on my iPhone 4S for iOS update. What I remember is first version of update 7.1 which was around 23 MB. I updated to the 7.1. After that appeared another version for update which was 7.2. So, I updated again

  • InDesign for wireframing websites?

    Do any of you use InDesign for wireframing websites?  I need to create a wireframe for a site.  I was all prepared to do it in Fireworks.  Fireworks has some fantastic features, but I need better PDFs than what it can export.  (I tried every setting

  • How to create storage locations in a standalone scenario??

    Hello everybody,    I need some help. I'm working with SRM 5.0. I'm making a standalone scenario. When I created the organizational plan, in the check tab, a error appears. The message is: "Define the attribute LAG". The attribute LAG is the storage

  • How to validate the input field

    Hi, I have a input form which is draged from input port of a RFC. in this input form i have two input fields nad submit button. on of this input field should always take the character values only. it should not take any numeric value and other input


HashFlare