Msi k8n neo platinum - The 1394 delete from bios device list

hi.
the line where 1394 was is now empty , i try everything i flash the bios and stuff
no luck for me???
it look like the 1394 onboard conroller is dead?

A thread here , from when 1.56 appeared:
MSI K8N Neo Plat Beta Bios 1.56
and when 1.55 appeared:
New Bios For MSI K8N Neo Platinum [ 1.55]
Seems to me that the 1.5x series were focused on chipset timings and ram .
Another thing is that i can boot from a usb pen with this one .(never got it to work with others) .
Beta bioses don't come with a changelog , they leak out . So any complete
list of changes is not possible to provide.

Similar Messages

New Bios For MSI K8N Neo Platinum [ 1.55]

NEW BIOS FOR MSI K8N Neo Platinum !!!!
BIOS 1.55 FOR K8N
AND CLICK
Apothikeusi/Emfanisi (Greek Language )
Your CPU temperature is in the safe range. Please rest assured. If you are
willing to, would you please flash BIOS to the version 1.55 verifying? We
send it by attachment. As to how to flash BIOS, please refer to the word file
in the attached file. Please kindly inform us of the results. Thanks for your
cooperation.
In addition, please enter BIOS to load optimized defaults after flashing BIOS.
Please feel free to let us know if you still have any further issues or inquiries.
Best regards,
MSI Technical Support

OMG !!!!
Something is really weird about this bios !!!!
I can't boot overclocked from bios even at 220 HT, and at the beginning i was REALY disapointed.
Then i set it to optimize defaults ( and yes i did the whole flashing thing ) and i am now IN WINDOWS with my cheapo Kingston Value that did MAX 230 with problems NOW AT A WOOPING 237 Mhz and still going UP !!!!
OMG OMG....
If only i can get it to boot from bios.Seems pretty stable in windows even at 237.
Really strange guys.I thought 230 was my memory limit....
Gonna try higher and let you know.
P.S. this bios seems to like Kinston Ram....Value at least

*UPDATED 7/15/04* Complete guide to bioses, drivers, and needed files for the MSI K8N Neo Platinum

Complete newbie's guide to bioses, drivers, and needed files for the MSI K8N Neo Platinum:
Last Updated: Thursday July 15th, 2004
Bioses:
(In order of date released.)
1.1b3 - (Download)
- Pre-1.1, given to reviewers to use in their reviews and benchmarks.
- Less stable, but supposedly you get slightly better overclocks.
1.1 Official - (Download)
1. This is AWARD BIOS release
2. This BIOS fixes the following problems of the previous version:
- Memory always run DDR 200 when install single side DDR on DIMM2 & DIMM3.
- Windows 2000 can't format the RAID IDE HDD when plug in Promise 378 controller.
1.2b5 - (Download)
1.2b7 - (No Download Yet)
1.2b10 - (Download)
- First attempt to fix false temperature readings. Fixes it for some people with Newcastle cores and doesn't fix it for anybody with Clawhammer cores.
1.2b12 - (Download)
- Second attempt to fix false temperature readings. Fixes it for some people with Newcastle cores and some people with Clawhammer cores.
1.3b1 - (Download)
- Another attempt to fix temperature problems?
- Possibly fixes cold boot/power light issues?
1.2 Official - (Download)
1. This is AWARD BIOS release
2. This BIOS fixes the following problems of the previous version:
- System can't resume from S3 sometimes when install USB device.
- Support K8 Sempron CPU.
- Turn off keyboard LED in S3.
--Quick Guide for flashing BIOS, provided by MSI--
1. Create a MS-DOS boot diskette, then copy the the .exe and the bios file to the floppy disk. Both of these files can be found in the package you downloaded.
2. Press "Delete" and go to BIOS setup while computer bootup.
Check BIOS advanced features and see if BIOS flash write control is enabled
(This option must be enabled. If you can not find this setting, it means the BIOS can be
flashed.)
3. Boot from MS-DOS boot diskette and get a:\> prompt.
4. Type "", then press ENTER
5. The flash program will then ask "Do you want to save BIOS?", please press "N" for no. The when you see Press 'Y' to program or 'N' to Exit, please press "Y" to continue.
6. After flashing complete, remove floppy and reset the system .
7. Press DELETE or F1 when prompted at first reboot after flashing.
8. Load BIOS optimized defaults, then save settings and exits.
Drivers & Needed Files:
(Note: All these drivers are for Windows XP.)
Leaked Nvidia nForce3 Chipset Drivers Version 4.40
(Please use at your own risk, these are LEAKED drivers. Password for the .zip file is "ocworkbench rules". Also, you will need to rename the WinXP_2K folder in IDE to either WinXP or Win2K else the installer doesn't pick it up.) Thanks for the link Wonkanoby!
*NEW* Leaked Nvidia nForce3 Chipset Drivers Version 5.03
More leaked drivers? Seems some parts of the drivers are older and some are newer.
1. Windows XP Service Pack 1A (Web Install) -or- Windows XP Service Pack 1A (Full Install)
2. Microsoft DirectX 9.0b (Web Install) -or- Microsoft DirectX 9.0b (Full Install)
3. Nvidia nForce3 Chipset Drivers Version 4.24
4. AMD Athlon 64 Processor Driver Version 1.1.0.14
5. Nvidia Video Card Driver Version 56.72 -or- Omega Nvidia Video Card Driver Version v1.5303
(The Omega drivers are third party drivers optimized for gaming, most prefer these over the standard Nvidia drivers.)
5. ATI Video Card Driver Version 4.7 -or- Omega ATI Video Card Driver Version 2.5.51
(The Omega drivers are third party drivers optimized for gaming, most prefer these over the standard ATI drivers.)
6. Onboard Sound Driver (Realtek AC'97 Audio Codec) Version A3.61
It is HIGHLY reccomended that you install the drivers/needed files in the order listed above. Please note that there are two #5's because you either install one or the other depending on your video card, do not install both of them.
You will come across a problem here though. You can't install the chipset drivers without installing the Windows service pack and DirectX first, but the Windows service pack and DirectX installs need the internet to download files and you won't have working internet until you install the chipset drivers. Here's what I did to get around this. Instead of downloading the web install versions of Windows service pack and DirectX, download the full version and and put them along with all the other drivers on a backup hard drive or burn them to a CD, this way you will have all the drivers you need when it's time to install them and none of them will require the internet to download files.
Another note when installing drivers. Apparently the Nvidia chipset drivers also come with drivers for the onboard sound, but people seem to agree that the Realtek onboard sound drivers are better. When you are installing the Nvidia chipset drivers, just be sure to uncheck the box for sound drivers when it asks you which drivers you would like to install. Now you can safely install the Realtek drivers without any chance of conflicting sound drivers. Thanks for the tip Wonkanoby!

Quote
Originally posted by RLiu818
Quote
Originally posted by Deviation56
Quote
Originally posted by RLiu818
You CAN install the nforce drivers BEFORE installing SP1. The only requirement to install the nforce drivers is DX9.
So is SP1 still recommended to install before the nforce drivers?
The installer still reccomends to install it beforehand for full USB 2.0 functionality... I would have put what you said in there but I wanted to keep it as simple as possible.
oh. IIRC the installer just says USB 2.0 will be fully functional after SP1 is installed. So after you install SP1 you go into device manager and u click update driver and it will auto search and update the driver.
Simplicity-wise, i guess its pretty much equal. It might take less preparation to just copy DX9 full onto a CD and install that first, then nforce driver, then right away you have yoru internet connection.
but i dunno.. i guess i will try it your way this time when my RMA"d board comes.
i will be fomratting and doing a fresh install later on today and will let you know if i come across any problems

Bios from my Msi k8n Neo Platinum (socket 754)

Wich is the last beta bios from my Msi k8n Neo Platinum (socket 754) ?
And where download?
Thanks

A thread here , from when 1.56 appeared:
MSI K8N Neo Plat Beta Bios 1.56
and when 1.55 appeared:
New Bios For MSI K8N Neo Platinum [ 1.55]
Seems to me that the 1.5x series were focused on chipset timings and ram .
Another thing is that i can boot from a usb pen with this one .(never got it to work with others) .
Beta bioses don't come with a changelog , they leak out . So any complete
list of changes is not possible to provide.

Using the Zalman CNPS7000B-AlCu + Zalman ZM80D-HP VGA heatsink on MSI-K8N NEO-Platinum

Hi,
Im buying a Athlon 64 system very soon (today or tommorow) and have the following question regarding the MSI-K8N NEO-Platinum. I know the Zalman CNPS7000B-AlCu fits on the mobo but it gets very close to the videocard. How close does it get? Can I still use the Zalman ZM80D-HP VGA heatsink? If anyone knows this please let me know.
Thanks in advance

Hi SirMurray,
I have the CNPS7000A-AlCu and the ZM80C-HP and the 7000A-AlCu is only about 2cm (maybe less) away from my graphics card. There is no way to have both the 7000A-AlCu and the ZM80C-HP (same goes for ZM80D-HP as Im 99% sure it is the exact same size as the ZM80C-HP) installed together without modifying the ZM80.
I was quite dissapointed about this cause I really wanted to use both so I tried to move the back heatsink of the ZM80C-HP but no matter what I did it just woulnd't fit with the 7000A-AlCu... BUT!...
What I did was to modify the ZM80 so that instead of the heatpipe going from the front to the back of the card as usual, it was turned around, so that the heatpipe now passes in front of the front-side heatsink. I then mounted the other heatsink (usually at the back of the card) so now both heatsinks are situated on one side of the card. Once I locked them in place with the little brackets they give you to join the two heatsinks it was done!
p.s. just in case you are wondering, the heatsinks are quite light so there is no real danger in having both placed on one side of the card. they don't pull the card to one side or stress the gpu mounting gear, etc. any more than having them installed normally. also, they are far enough apart when both on one side of the card for good airflow between them.
This all works for me and I haven't had any problems with it at all. It does mean that the whole graphics card + heatsink covers a LOT of PCI slots (4 I think). This is okay for me as I only have one PCI card (audigy 2) installed. Also, if you need to fit the optional fan for the ZM80 than you might run into trouble as the spacing between the heatsinks is smaller when using this setup than when they are installed as per zalmans instructions (front + back).
Hope this helps!

"error loading operating system MSI K8n Neo platinum

OK,
System will post, according to MSI Website I have the latest Bios version.
I can boot from CD.
The only odd item is that I am using the HD that I took out of my old computer with windows already on it.
Tried re-installing windows XP. It went through the loading process and then rebooted. Same error message appears.
Also, is 48 degrees normal for idle temp on CPU AMD 64 3400? 36 degrees NB temp ok?
Oh, yeah, I have a floppy installed, CD-ROM, CD RW, all non SATA. Using IDE cables.
Video is Asus V9980 ultra GeForce FX 5950.
MSI K8N Neo Platinum
AMD 64 3400
Hercules 600 W PSU
WD 80gb HD
Generic CD-Rom
Sony Cd-RW
2 x 512 crucial 400 ddram slosts 1 and 2
Asus V9980 ultra GeForce FX 5950 256 TVD
Do I need to clear bios and re-start?
HD is on it's own cable in IDE 1
Cds on IDE 2 shared.
let me know what you think.
The other related posts I read, people were using raid or multiple OS. I'm not.

I had the same issues as you sometimes Windows would install and sometimes it wouldn't the problem was related to ram. I had my ram in slots one and two like you did and I moved the ram to slots 1 and 3 and now the machine is rock solid stable.
I think most of the problems people are having are actually more ram related than anything else.
So try moving the stick of ram you have in slot 2 to slot 3 and see if this solves your problem. This solution is on forums somewhere I am just not sure where.
Take care,
Bob

MSI K8N NEO Platinum Edition memory question

Hi there,
I've currently got a MSI K8N NEO Platinum Edition (Nforce 3) motherboard and 2X 512 MB Corsair Value Select memory modules (both double sided) running at DDR 400 - this runs completely stable and has done for a number of months. I would like to increase my memory to 1.5 Gig but there seems to be a lot of issues?
I originally planned to buy an additional 512 Meg Corsair value select chip and place it in Bank 3 - is this acceptable?
I assue that i would have to drop the speed down to DDR 333 from 400, could anyone tell me how much of a difference this actually makes (when playing FPS games Doom3 etc..) ?
Any help would be greatly appreciated as i've been looking through both this forum and the Corsair one and i cant seem to find the answer.
thanks in advance !

Just note that there are combinations of two sticks that will also make the board run in DDR333 mode (see page 2-8 of the manual). For example, using two double-sided sticks in DIMM2 and DIMM3. I've actually managed to get it to work at DDR400 in those two slots, but it's not perfectly stable and overclocking diminishes drastically. Bottom line is the system will work fine when forced to DDR333...as long as you don't expect to overclock the RAM to any significant degree.

Help with MSI K8N Neo Platinum

HELP please- motherboard MSI K8N Neo PLATINUM: I tried to take away the backplate for the heatsink (on the back side of MB) in order to install the zalman HS beafore i read the forum (use a fan...) and the worst of all happend:
I scratched the back surface!! the scratches are minor, that is 4 scratches half a milimeter long each and not deep but i can see the copper of some lines leading from the memory slots to the processr. My question is : can I try and build the computer on that motherboard anyway or better buy a new one? is there a risk of dammaging other components? oh god what a mistake!

Make sure the new backplate is non-conductive. The backplate for the Hyper 6 has a non-conductive sticker on it. Make sure to keep it on if youve got one... If the lines are exposed even with the back-plate on perhaps you should cover them with some non-conductive (100% non conductive!) tape or something.
Then it doesnt matter if they are exposed, as long as they are ok.
A good tip, which got when i was removing my backplate, is to use a blow dryer to heat it up and the remove it with your fingers. That way youll also notice if it gets to hot
The glue gets sticky at blow drier temps. And pls, dont singe the MB with your blow dryer, you only have to make it hot, and if you cant touch it, how can you remove it with your fingers?
I guess theres no way of telling if you have a serious prob and no way to tell if your cpu will be ok. I guess you could (?) try and start it wíthout anything (cpu, mems) but a PSU, and then, if it (and maybe the PSU) goes "!Pfsssssss!" or "bang!", youll now you will have to replace it.
I put a screwdriver through an asus board once, and it still worked...

MSI K8N Neo Platinum | system freezes!

Hi,
I recently bougt a MSI K8N Neo Platinum and an A64 3200+ Clawhammer Boxed. I was looking forward to low temperatures and a stabile motherboard, but I haven´t been that blessed yet. During random cpu loads, I get system hang-ups. Wether it´s running iTunes, CS, Sisoft Sandra, FarCry or nothing at all, the system sometimes stops responding.
I´ve updated to 1.2 BIOS, and I´ve downloaded the unofficial 1.33 BIOS from this forum , haven´t tried it yet, though.
MSI Corecenter tells med that the CPU temp gets above 55 degrees under full load. Atually, I had up to 70 degrees until I installed a third case fan. But the sys temp reports from 45 to 50 degrees. And I guess this is the little "MSI"-marked heatsink´s fault. It gets burning hot.
Could the system temp be the cause of my hang-ups?
Hoping for tips and possible solutions.
Btw, sorry for my norwegian-english

Hi,
I recently bougt a MSI K8N Neo Platinum and an A64 3200+ Clawhammer Boxed. I was looking forward to low temperatures and a stabile motherboard, but I haven´t been that blessed yet. During random cpu loads, I get system hang-ups. Wether it´s running iTunes, CS, Sisoft Sandra, FarCry or nothing at all, the system sometimes stops responding.
I´ve updated to 1.2 BIOS, and I´ve downloaded the unofficial 1.33 BIOS from this forum , haven´t tried it yet, though.
MSI Corecenter tells med that the CPU temp gets above 55 degrees under full load. Atually, I had up to 70 degrees until I installed a third case fan. But the sys temp reports from 45 to 50 degrees. And I guess this is the little "MSI"-marked heatsink´s fault. It gets burning hot.
Could the system temp be the cause of my hang-ups?
Hoping for tips and possible solutions.
Btw, sorry for my norwegian-english

MSI K8N Neo platinum sound prob

Hi!!
I got myself a MSI K8N Neo platinum...
every 20 secondz my music hangz...
why? don't ask me.
any answers? and when my music hangs I have a look at the ctrl+alt+delete menu and I see that my cpu load goes to 46 percent when the music stops...
help...
cheerz Xyus!!

Hi!!
I got myself a MSI K8N Neo platinum...
every 20 secondz my music hangz...
why? don't ask me.
any answers? and when my music hangs I have a look at the ctrl+alt+delete menu and I see that my cpu load goes to 46 percent when the music stops...
help...
cheerz Xyus!!

MSI K8N Neo Platinum - CPU Cooler?

Hi there, this is my first post to the forum and hope that someone can help
Bascially I've just purchased a MSI K8N Neo Platinum mobo to use with an AMD 64 2800.
I'm wondering if I should use the stock CPU cooler or look to purchasing a cooler such as a Zalman? I want to keep the computer as quiet as possible.
I've recently read that it would be better to use the Cool and Quiet option with the stock CPU cooler instead?

Chris,
If you don't mind a used one, there are probably about a hundred thousand available ones from people in these forums who has upgraded their heatsinks, and that's about everyone
The problem is, we dont want to give them up. We bought the retail package with fan not because of the free heatsink/fan, but because of the 3 year warranty that you only get with said combo. To invoke the warranty, we'd have to return everything, including the heatsink/fan, so we hang on to it and let it collect dust.
So, for an aftermarket fan. If you don't plan to overclock, ever, the thermaltake silent boost K8 will do, although it is nowhere NEAR the 21dB that tt claims. They are known for shall we say, exaggerated claims. But it's certainly quieter than the stock HSF, and it's available everywhere.
Note that the "silent boost k8" is different from the "silent boost". The latter is for socket 462 I think.

MSI K8N NEO PLATINUM (RAM/HD problem/mobo problem?) [SOLVED]

my setup:
windows xp pro sp2
amd athlon 64 3200+
msi k8n neo plat - 7030 - bios 2.1
x800 xt vid
sound blaster audigy 2
kingston valueram pc3200 2x512 cas 3-3-3-8
ps = antec 430 watt truepower power supply (20 A on 12V)
I dont know if you guys remember my but i created a topic on here a while back about how my keyboard and mouse suddenly stopped working, well that turned out to be that the msi k8n neo platinum just went bad. So i RMA'd it and recently got the replacement board (with latest bios already installed). It worked completely fine for about a day. Well that same day i got it back, i installed a Logitech G7 USB wireless mouse. after i installed it, i began getting numerous windows stop blue screen errrors, even after i removed the mouse from control panel. So i figured i should format because to rule out everything and start fresh. So i did a FULL format and attempted the reinstall windows again. AFTER the format and BEFORE windows attempted the continue installation, i got the same stop error. I figured now this was a hardware problem. So first i tested RAM. I got the latest version of memtest86 and let it run for 4 hours (11 passes) with NO errors at all. Secondly, i got a western digital hard drive diagnostic program to test for failing hard drive and again no problems with that. I still suspected ram so i tried to boot with only 1 stick installed (in first slot), however the PC didnt boot at all (cleared cmos too). So i moved it to the second slot and cleared cmos again and this time it posted but it just hangs at a cursor and does nothing, same thing happened with third slot. I tried this same procedure clearning cmos each time with the second ram stick and got the SAME results. Shouldnt the motherboard boot with only 1 ram stick installed? Did MSI RMA me another bad board? Any help would be appreciated. thanks.

Quote from: russellmrgn on 28-March-06, 10:54:39
Sap147
Can you give us what the D-Bracket was showing ie
R R
G R
As an example this means "Initializing Keyboard Controller"
You will find this information in the manual page 2-23. (On mine) under Hardware Setup
Also can you please do all your tests with the ps2 keyboard and mouse and for now leave your Logitech G7 USB wireless mouse to one side.
Russell
for two sticks of ram = RR
GG
for one stick of ram = GR
GG
as for the g7, it hasnt been plugged in at all, i took it out long ago.. as for the ram, the timing was set to 2T, no overclocking, i will try 2.7 v and let you know, but for the record, it has been running at normal voltage settings for about a year perfectly fine.

MSI K8N Neo Platinum Nforce3 250GB - PSU?

My sister in law have this board, MSI K8N Neo Platinum nforce3 250gb chipset, recently the power supply sounds noisy and a high frequency sound from the Antec Truepower 380W SP. Had maked an RMA to Antec and they had agreed to replace the 380W psu with SmartPower2.0 450W. But they asked me one question, that im not sure about:
"Make sure that your motherboard does not need the -5V. If you want more information on the power supply you can look at this link: http://www.antec.com/us/productDetails.php?ProdID=26450 "
So, do Antecs SmartPower 2.0 450W suits this board and what really is -5V for? As I read the manual, it said ATX 20 pin power connector: JWR1 and at pin 18: -5V
So does it mean this board need a psu that gives -5V on ATX 20 pin power connector and thos board can't use with Antecs SP 2.0 450W?

Quote from: syar2003 on 22-February-06, 05:10:37
Hi!
The K8N Neo Platinum (MS-7030) doesn't use -5v to anything.
So the -5v from the old atx spesification is not needed in your case.
WoW, thanks for fast reply!
So, it won't be any problem to use Antecs SmartPower 2.0 450W with this board then? Want to make sure about it, before accept Antecs offer for replacement and had spent over 4 days to find the problem with his computer. Really don't want to do it again.
This is his riggs:
Antec Sonata
AMD 64 3000+ S754
Corsair Value S. PC3200 DDR 512MB
Maxtor Diamondmax 9 250GB SATA
Maxtor Diamondmax 9 IDE 160GB
Sapphire Radeon 9550 Atlantis 128MB DDR
and
Accton ethernet card on PCI slot
MSI D-Bracket2
so
With the "new" Antec SmartPower 2.0 450W
Any problem with this rigg and PSU?
edit:
Dound this post that it said the board do need -5V and now Im confused?
http://www.archivaty.net/forums/about12964-30.html

MSI K8N NEO platinum and MOBILE chips

I just found out a problem with MSI K8N NEO Platinum.
I recently upgraded my cpu from Clawhammer DTR 3200+ 1.5V to Clawhammer Mobile 3400+ 1.4V (hoping for better overclocking). To my surprise the mainboard can no longer raise the VCore voltage over 1.45V (it doesn’t matter if I select in the bios 1.5 or 1.55V). The only working option is raising de VCore by 3.3% 5% 8.3% 10%, resulting in a maximum VCore of 1.45 + 1.45 x 10% = 1.6V
I did some googeling and found there is a VCore issue with the K8N NEO and mobile chips, although DTR chips are fully supported (working VCore and multiplier adjustments).
I am using the latest beta bios 1.56B (moded by Pinochio)
Did any of you found a way to resolve this problem? IT IS DRIVING ME INSANE!!!

Bad post...

MSI K8N Neo Platinum with Vapochill Case problems - Help anyone. :)

Hi all,
Had a bit of a tricky problem and as Im new to this board I have no idea what could be causing this.
First all all system specs:
Athlon 64 3700+ Clawhammer
MSI K8N Neo Platinum -
1 gig Corsair XMS ProL Low Latency Ram (2 x 512mb)
Nvidia Gefore 6600GT
1 x WD Raptor 10000rpm HD
NEC 2500a DVD writer.
Eye-T 550w PSU.
Vapochill SE Case with installed Vapochill Phase change cooling.
Here are photos of it in its present state, you will notice that it isnt installed in the case at the moment.
The reason for that is because the two wont work together and I want them to so so bad...
So, hopefully someone here can save the day for me - here goes.
I have tested the Motherboard and all other componants outside of the case and everything runs smoothly and there are no problems what so ever, great.
I have also retested the Vapochill case with another motherboard and that also works without a hitch.
The problem comes when I insall the MSI board into the system, all hooked with a really basic setup, PSU, Case cooling, CPU and Ram. Flick the on switch on the power suply and the system turns on for around 1/2 a second then turns off again. I found this strange because it soundnt come on at all until I press the power button.
If I press the power button the same thing will happen over and over.
I have tried a different powersupply and this does nothing at all.
I have checked for shorts and there is no possible way it is shorting on anything.
I have a fan plugged in where the CPU fan would go and this doesnt help.
I have taken it back out and tested it again and it still works ok.
Does this sound familiar to anyone? Are there any secret Bio's menu's that would have an option that would solve this?
Any help would be greatly appreciated.
Glenn

When you are running the MoBo standalone, what are you connecting to the Power, Reset, HDD, etc. pins ? Are you using the wires from the Vapochill case, or something else ? It looks like a single cable with an intermittent switch (red/white cable). I once had a similar sort of problem and it was because I hadn't connected up (the incredibly fiddly) cables correctly. Other than that, I would have gone for a short of some sort - but you have checked that already, so . . . .
As to the system starting to power-up when you switch on the PSU, I wouldn't worry too much about this. It seems to happen from time to time with some of my systems - amongst other things, the BIOS can be set to resume to previous state after a power-fail.

Msi k8n neo platinum - The 1394 delete from bios device list

Similar Messages

Maybe you are looking for