MSI K8T Neo FIS2R - Memory problem???

I have bought myself a second stick of ram for my computer, being careful to make sure it was exactly the same brand and model.
In spite of this I now get random bluescreen errors of varying types, the first was PFN_LIST_CORRUPT and the latest:
PAGE_FAULT_IN_NON_PAGED_AREA
STOP: 0x00000050 (0xC5AD0D7C, 0x0000000, 0x8050298A, 0x0000000)
Is the new ram incompatible?? this makes no sense though.....   ???

I have tried switching ram sticks around but no luck there
Got three BSOD's yesterday, no specific error just STOP: blah blah blah when trying to burn a CD and then after that just when using IE.....
........and then I played call of duty 2 for 3hours without a single problem 
Today when trying to run FS2 open I got two IRQL_NOT_LESS_OR_EQUAL errors (with no driver mentioned)
Anyway, I have been doing some research on socket 754 athlon 64's, and I found some interesting info from AMD:
Where MSI says that the board supports that config at DDR400. so the board supports it but the CPU doesn't! what is the point of that??
I tried running at DDR333 but the CPU stuck at 1.8GHZ (150FSBx12) according to everest 
Is it possible at all to run two sticks of Double sided ram at DDR400? surely someone has done it and has it working....
Another thing, after the first IRQL error my computer hung at detecting the CD-RW drive and I had to turn off and on again  ???

Similar Messages

  • MSI K8T NEO-FIS2R: RAM problems

    I have the motherboard K8T NEO-FIS2R with AMIBIOS 2VMS V2.0 010505.
    I tried these DDR-RAM:
    DDR-RAM 512MB PC400 CL3 Kingston KVR400X64C3A/512
    DDR-RAM 512MB PC400 CL3 Samsung
    but the motherboard recognizes only 256 MB for both. The RAM are good: I tried them in an other pc!
    Now I have installed an A-DATA ram 256 MB and the motherboard recognizes 256 MB!
    Do you think that my motherboard is defective?
    Thank you in advance.
    P.S. I'm sorry for my bad english.
     

    No the memory controller is onboard the CPU so in any case the MB is not defective. However the CPU revision may hold you back on some RAM especially if you mix make and model RAM on the same channel. A socket 754 CPU only has one channel so all RAM must be matched to work properly.
    If those Sticks can only be seen as a wrong value when used by themselves it is likely that either they have errors or the timings in Bios are improperly set to azllow them to work. In this case you can normally find out what is going on by running memtest86. If you get errors on test 5 or 7 then you have timgs timed improperly and any other errors would show bad RAM.
    Another case is not having enough power for everything to work properly together. Usually this happens when you don't have enough 12v amps for these newer rigs.
    Post complete specs and test results and maybe we can help you further.

  • AMD64 3200 + MSI K8T Neo FISR2 memory problem

    I've had one KVR400X64C25/512 and it have worked like a charm. Now I've bought another one (total 1gb).
    When I've inserted it and start the computer I only get the CoreCell logo scren, it do not boot correctly.
    AMIBIOS is version 3.21a
    I've tried the following:
    * run only the new memory [works]
    * run only the old memory [works]
    * DIMM1 + DIMM3 [only CoreCell screen]
    * DIMM1 + DIMM2 [only CoreCell screen]
    * DIMM2 + DIMM3 [only a black screen]
    what should I do?

    Quote from: Tiresmoke on 22-August-05, 21:48:12
    A PSU is rated to run at +/-5% and that is well within it's rating. As for wether ists big enough there is no way we can say as you still did not give full system specs.
    If it won't run with the third stick of RAM then pull it out for the moment and see if the system will boot again. If it does then during post you will see a Bios version listed. That board only supports Bios versions to 2.2 at the moment so please also list what actuall Bios version you have.
    Ok, have booted with one instead of two sticks (one works, two don't, do not have three sticks)..
    AMIBIOS A6702VMS v2.2 released 030405. The autodetect settings (at startup): Clock = 400Mhz, CAS 2.5 which seems correct.
    More info:
    AMD64 3200
    MSI K8T Neo FISR2
    AMIBIOS A6702VMS v2.2
    Seagate 120GB SATA (no ides)
    CD rw + DVD-r combo drive
    floppy drive
    Saphire GF6800 (no GT or Ultra)
    Creative Audigy 2 Platinum Ex
    that's whats running in it

  • K8T Neo-FIS2R Memory Problems

     Hello,
    First can I say thanx in advance for any help that I might get, I'm new to this board and I appretiate the hard work you all put in to the comunity.
    The problem originaly was that this board would only work with one memory stick. It did not matter how big it was 256 - 512 - 1GB, it would boot, but if I added another say 2X 512 the system would not boot, the screen would just stay black.  I upgraded the bios from the MSI site - the file name was 6702v22.zip.
    The system now boots fine with 2X memory sticks is (that cured it), but now I find that I cant alter the memory timings. No matter what I set the CAS to it always defaults to 3, Its like its stuck on auto for some reason. I reset the bios after the flash, and tried different slots, different memory sticks, but the bios seems to ignore any manual settings I put in there.
    Can anyone shed some light ?
    Thanx
    Umpa....

    Duh. I read your post completely. The reason behind asking for specs is simply to investigate issues with older CPU's running the newer Bios's and vice versus. Yes there are known issues but as you are not going to supply specs then I am not going any further either. However you already have guessed my point and yes I have one of those MB's myself and can tell you firsthand what happened to me when I ran my older CPU with the newest Bios.
    While that may or may not be the answer think about this;
    This guys calls up a car mechanic and asks if he can help him with his car. The guys tells the mechanic that it makes a noise when the engine is turned on.
    The Mechanic replies that he would like to know what type of car this is and if he can describe the noise.
    The customer says, It's a red car and it growls.
    The Mechanic replies that it would cost aboy $50,000 to fix.
    The Customer is floored as he does not understand.
    The Mechanic replies that without further info the best he can do is to replace the entire car.
    Granted that is kind of a stupid story but rememer that we don't have a crystal ball. The symptoms you describe with out us knowing more could be a few different things but trying to give an appropriate answer is difficult to pinpoint better without good info. It could be the RAM, the PSU, the Bios or maybe a setting. It may even be something stupid like the RAM socket combo your using. LMAO Yes that can also lead to this kind of thing happening as it did for me when I first got mine setup. I also had stability issues until I changed from sockets 1 and 2 to 1 and 3.
    Ao you can see there is no single answer that will fit. I could care less about what hardware you run nor can anyone else here other than to help you. So go ahead and be stubborn about helping us help you. It's your rig that needs help not ours.

  • MSI K8T NEO-FIS2R Sound Problem

    Why does the sound cut out after a period of about 5 hrs or more it completely stops in windows XP havent tryed any other OS,  i keep having to restart the computer to bring the sound back!
    Any help on this would be greatly Appreciated

    Quote
    Originally posted by joshr45
    Why does the sound cut out after a period of about 5 hrs or more it completely stops in windows XP havent tryed any other OS,  i keep having to restart the computer to bring the sound back!
    Any help on this would be greatly Appreciated
    Do you have LiveUpdate installed (or whatever it is called)? When I was using the onboard sound (moved to an Audigy2 ZS) the sound would go once Live Update had searched the web for available BIOS/Driver updates.  I only had mine set weekly but sods law meant that I ended up with no sound for a Rugby World cup I had recorded on my AIW pro (aaaarrgghh). It would only come back with a reboot.
    Alex

  • Msi k8t neo fis2r problems part 3

    sometimes when the computer is turned on it just turns the fans and leds on but doesnt boot up...
    most of the time it loads up and i boot to the windows xp cd and i install the drivers for sata and then when it reaches the point of copying the files it will give me a bsod and say that there is a problem with the irql driver and then force me to shut the pc down..
    sometimes it makes it past that and will begin to copy files onto the hard drive, like somehow the data is becoming corrupted..however it will start to say that the files cant copy randomly and it will allow me to retry..they will copy the 2nd time usually..i can keep hitting retry and it will usually go by..it gets to 30 something % and then crashes to bsod just giving me some random error..for some reason the files keep screwing up that go on the sata drive....I just replaced the old power supply that wasnt working with an antec true watt 430 watt power supply, so i know it isnt that..
    i just cant figure out what the heck is going on..any help would be appreciated.my specs are
    "IRQ NOT EQUAL OR LESS"
    athlon 64 3000+ cpu
    msi k8t neo fis2r motherboard
    mushkin special cas 2.0 2-2-2-5 512 mb pc 3200
    western digital 8mb cache 80 gb sata hard drive
    sapphire radeon 9800 pro 128 mb 8x agp

    fyi look an your cd sticker ity will show power, consumption, but they are way lower than you would think, hard drives,can be only 10 watts, less then some case lights , and fans, cd are  similar.. your video, is the biggy somewhere between 90~150 watts..yikes .next to the cpu..and the mobo can use 50 or so (not sure about new mobos)  not to mention the ram 1024 is @40 watts or so., dont forget about 25watts per pci card, not counting the sound card which can be double....
    ergo the need for a big psu..
    the combined total ratting on a psu is not the max number that the psu is rated, that is surge value.. so a 500 may only hold 400 sustained , and that will drop as the machine heats up, so in the end your 500 may onlyy pull 366 @50'c...

  • Problems with OC in MSI K8T Neo FIS2R!!!

    Hi!
    I have faced problems when making OC in my Athlon 64 3400+. I do not obtain to increase the FSB for 213Mhz more than without that they occur stopped or reset. I am using 1Gb (2x512) of Ram (Corsair CMX 3200LL PRO).
    In the internet many stories exist that chip VIA K8T800 is not good for OC, because the AGP/PCI cannot be stopped with fixed values.
    Exists some form to obtain with stability in this Mobo one overclock descent, with FSB of at least 220Mhz? The lack of stability in overclock limits the processor very, what it finishes in forcing to who knows to abandon the K8T Neo, passing to a Mobo that uses Nforce3 250, for example.
    If somebody will be able to help with tips to try one overclock for FSB in 220mhz with stability would be very grateful, friends!
    my system
    Athlon 64 3400+ (cooler venus 12)
    MSI K8T Neo FIS2R
    1Gb Ram (512x2) Corsair CMX 3200LL PRO
    ATI Radeon 9800XT 256Mb
    120Gb SATA Maxtor 8mb buffer
    Audigy 2
    420W Thermaltalke
    Case Lanfire Thermaltalke
    Monitor LG Flatron 17 700P
    CD/RW+DVD
    LAN (adsl 400k) + Fax Moden (56k)

    Take your sata drive off and you can overclock higher. There is no PCI/AGP lock so the speeds are affecting your sata drive. 210 mhz. system clock is about the limit before the sata drives start to act up.
    The problem is with that particular VIA chipset. No way around it has been found to work in a practical manner.

  • Msi k8t neo fis2r xp install problem

    I tried to install xp on my sata drive..i downloaded the raid drivers and put them on a floppy, it accepts the raid drivers (im not trying to use raid, just regular sata), and i select the hard drive and attempt to install to it, but the files from my xp cd keep saying something about invalid image has been installed to your hard disk (or a similar message to that)
    also part of the time the comp will not boot properly, it will just beep on and hang and nothing will show to the monitor, or if i have a disc in my cdrom when i try to turn it on it wont turn on, but then when i take out the disc and reboot the comp it turns on again..no clue what might be going on..
    my specs are
    a64 3000+
    512 mushkin special 2-2-2-5 cas 2.0 ram
    80gb WD SATA 8mb cache HD
    radeon 9800 pro (sapphire)
    MSI K8T NEO FIS2R
    sparkle 400 watt power supply

    You better get something like an Enermax 465 for your rigg, as yours:
    Quote
    Output: [email protected]/28A,+5V@40/28.5A,[email protected],+12V@15A,[email protected],+5VSB@2A
    Could blow to pieces any minute now....
    15A @ 12V is way too light.....
    The Enermax has 33 of them

  • Problem with MSI K8T NEO-FIS2R

    When I boot my computer I get a message invalid boot.ini then it says c:\windows and windows starts normaly. What I don't understand is why do I get invalid boot.ini Anyone knos how to fix this?

    I'm sorry for no specs. Here you go
    MSI K8T NEO-FIS2R
    AMD 64 3000+
    2X 512MB 400MHz Ceon CL=2,5
    HDD 120GB WD
    HDD 4GB SEAGATE
    CDR DVD-RW NEC ND3520
    CDR SONY
    400W POWER SUPLY
    primary master CDR DVD-RW
    primary slave NONE
    secondary master CDR SONY
    secondary slave HDD 4GB
    and last HDD 120GB on primary raid
    NONE on secondary
    I have ORIGINAL windows xp with sp2 on 120GB HDD. I bought this computer and they put windows xp on my system.

  • MSI K8T Neo-FIS2R (Socket 754) and Corsair 1GB DDR Value Select PC3200 Kit (2x512MB)

    Hi I just ordered the following from overclockers.co.uk and wanting some confirmation that the memory will be compatible with this Mother board
    Corsair 1GB DDR Value Select PC3200 Kit (2x512MB) and MSI K8T Neo-FIS2R
    Thanks
    Kevin

    kevtucker,     
    I'm running the same setup up as you and have not experienced any ram related problems so far. I'm happy with it and it is very stable.
    Every ram has different settings. For the corsair 1gb value select (2x512mb) you must make sure you use these settings for the best results:
    put them in slots 1 and 3.
    use the settings 2.5-3-3-8
    set the ddr voltage 2.7
    I got that information straight from the official corsair forums:
    http://www.houseofhelp.com/forums/showindex.php?t=24410
    Good luck.

  • MSI K8T Neo FIS2R- Corsair Twinx XMS4000

    Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
       The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?

    Quote
    Originally posted by karinio
    Two weeks ago I have bought one MSI K8T Neo FIS2R with an AMD Athlon64 3200+.So far I used the computer with one DIMM of 256MB DDR PC2100 memory. This morning I have installed in the motherboard a pair of CORSAIR TWINX XMS4000 which comprises of two DIMMs of 512MB DDR 500MHz memory.
       The computer did never worked again. As soon as I have turned it on, although the whole system got power the screen was blank and the motherboard did not boot. Moreover, the D-Led system of the motherboard has all its leds red which according to the manual means that the processor is probably damaged.I have never overclocked my system and before install the memory it worked perfect. I have disconnected the whole computer but the problem still exists. Can you advise me what I have to do to fix it? What is the cause of the problem? Is there any way so that I can fix it?
    Hi dude i had identical problem, bought i extra stick 512 400 ddr and the system wont start. Make sure your motheoard support the made of ram. In my case Asus did not support corsaire. Also it could be the slots which are damage.
    bye

  • MSI K8T NEO FIS2R No VGA help plz!

    Hi, ive just purchased a new athlon 3000 64 cpu retail and an msi k8t neo fis2r motherboard, the specs and problem are below but plz bare in mind i am a system builder for the last 3 years i have tried alot of things to solve this.
    MSI K8T NEO FIS2R MOBO
    AMD 3000 64 RETAIL CPU
    AMD RETAIL HSF
    1024MB DDR333 SAMSUNG RAM
    120 GIG WD HD
    GALAXY GLACIER GEFORCE 6800 GT 256MB
    PIONEER 106 DVD WRITER
    400 WATT PSU (TSUNAMI I THINK)
    Anyway the problem is this when i put the system together and turned it on i dont get any vga the monitor just says NO SIGNAL and when i look at the graphics card the fan on it isnt spinning.
    Yet i have my old setup which is as follows,
    ASUS A7N8X DELUXE MOBO
    AMD 3200XP BARTON
    AMD HSF
    1024MB DDR333 AMSUNG
    120 GIG WD HD
    GALAXY GLACIER GEFORCE 6800 GT 256MB
    PIONEER 106 DVD WRITER
    400 WATT PSU
    Basically the same as above i just changed the cou and mobo now when the graphics card is in that system it works fine no problems as soon as i try it in the new a64 system it doesnt work the fan doesnt spin and nothing comes on screen, ive tried everything i know ive double and trebble checked connections and ive tried removing components and then trying it, no matter what the graphics wont work.
    I figured the motherbaord must be faulty and am going to contact the place i got it from but it would be good if anyone here knows how to solve it if it isnt the motherboards fault.
    thanks very much.
    ic3man1999.

    Thanks guys, huess what like an idiot i forgot to put the 4 pin 12v in :( doh
    Anyway it works fine now, but i have high temps core centre says 56 degrees right now while im typing this ? is this accurate or am i in trouble ?
    Oh yeah and everytime i load windows it says new hardware found ide channel then secondary ide channel then it says a problem occured during your new hardware installation and it calls the hardware HDC it says this twice aswell.
    ANy help guys ?
    thanks

  • Calling all old MSI K8T Neo-FIS2R users

    Ops i posted this in the wrong forum first time, this is the right place
    This for all MSI K8T Neo-FIS2R users, that have changed to the new MSI K8N Platinum nForce3 250 mobo, if I have the chance to swap to the new board should I do so, or does this mobo have its fair share of problems?
    Is the MSI K8N Platinum nForce3 250, a better board compared to the old MSI K8T Neo-FIS2R? Not taking into account overclocking.
    Like is the onboard sound the same or worse or better in your opinion? Is it any faster at stock? Are there any other advantages?
    Thx Xe

    I had a K8T Neo Fis2r at first.  I got a K8N Neo because I believed my Blue Screens were a faulty K8T Neo.  As it turned out, the Audigy2 I had in there was the problem, because I still got Blue Screens with the K8N Neo, and when I took out the audigy and used onboard my system ran stable.
    I havent had any of the apparent keyboard controller problems, or ANY other problems with the K8N.  My only instabilities have been the Audigy2's fault.
    Havent tried overclocking on the K8N Neo yet, maybe a little down the road.  As far as features go, the K8N has the hardware firewall on it (which I dont use) but apparently its "true" gigabit ethernet is better than the K8Ts.  Dont ask me to clarify that, lol
    btw Got my turtle beach Santa Cruz today and put it in my K8N Neo, crossing my fingers... =\

  • Will Gainward 6800GT fit my MSI K8T NEO FIS2R?

    Horror picture on a ABIT NF7-S
    I saw this picture and saw that the card i extremely long!
    Anyone here on the forum that can guarantee that my Gainward 6800GT card (with a red gainward cooler) will fit on my MSI K8T NEO FIS2R?
    MSI K8T NEO FIS2R
    Please?  

    I think I have found out the problem  
    Using my old Enermax (350) I was able to boot up the AMD 64 2800 every time but the PSU made this weird electrical sound - I think because it was being overloaded (I think as it doesn't make this sound when used with my XP 1800). I then reverted back to my new X-Pro (460w) and after a few attempts I managed to get the ram module and CPU powered... slowly adding more fans it became harder to boot and eventually the GPU fan wouldn't run once I plugged another fan in... I'm guessing this is because my PSU is too weak to power the juice guzzling AMD  
    I'll need to break the bank once again I suppose  

  • MSI K8T Neo-FIS2R VIA K8T800 Issues

    I am thining of switching from a P4 system to a athlon 64 system. Only I have a few problems.
    Will I be able to use an amd athlon 64 3000+ on the MSI K8T Neo-FIS2R VIA K8T800 motherboard??
    and also will I be able to use my OCZ 1GB (512x2) DDR533Mhz PC 4200 RAM (DUAL CHANNEL) on the motherboard as well?

    Hi
    I use Elixir from Ebuyers, thats the cheapest I could find, works flawlessly on the AMD 64 3200+, the label says
    ' M2U51264D88HB3G-5T
    512MB DDR 400MHz- CL3
    PC3200U-30330
    The sticks were taken from a KT4 Ultra, where they also worked faultlessly.
    Hope it helps

Maybe you are looking for