MSI P35 Neo2 FR beta Bios 1.72

Does anyone know where I can get the beta bios above 1.6 for the p35 neo2 fr MOBO, I cant find on any english download site Thanks !

Quote from: miamimuscleboy on 13-December-07, 14:57:15
Thanks ive been looking forever. . do you have problems going over 480 FSB dont know your specs but I am running e6750@ 3.8 @485 dont know if i can go much higher @8x but when i lower the multiplier to 7 and move above 485 the board wont post but I know the cpu clocks at 3.8 @485 all the time > maybe this bios will help.. also do you know if the MPS revision 1.1 or 1.4 makes a difference?
You got very got clocks for that 6750. I've tried booting at 500mhz before. No problems passing stability test. In fact Anandtech managet to get this board to 500mhz too.

Similar Messages

MSI P35 Neo2-FR / FIR

Hello,
Yesterday my pc didn't start and my motherboard status led were stuck on all green.After I turned off the PSU and turn it on again the leds went to all 4 red. After an hour of powering on and off ( and 1 CMOS reset) it went on red green red red (ram failure). I kept trying while changing the ram position around but no luck. While doing my attempts I notice that only a few times did the leds blink confirming that the their status changed. Also i noticed that when the leds blinked , the pc fans were making more noise, normal to when the pc is on and working. The other times i noticed that the leds just kept their old colors and the fans were a bit quite than normal.A few times the leds changed from red green red red to all 4 red (cpu failure) and with the fan noise like when pc is working normally.
The day before I had the same problem but I managed to start the pc within the first hour.
Now i'm stuck at all 4 reds with no status change on them and fan noise lower meaning i think that is not getting to the point where is checking the cpu,ram etc.
PC Configuration:
- Motherboard : MSI P35 Neo2-FR / FIR BIOS Vs : 1.C
- CPU : Intel e8400 no OC
- PSU : Fortron Blue Storm II 500 W
- GPU : Gainward ATI Radeon HD 4850 no OC
- RAM : 2x Corsair XMS2-6400 ver 5.4 no OC

Update:
I removed the battery and reset the CMOS. After 2-3 hours i reinserted the battery and now the status led blink once to red green red red ( ram failure). I had this ram failure problem for a long time but i used to fix it by a CMOS reset or a few movement of the rams and was fine for a couple of months until it resurfaces at random.
I have tried 2 different rams and the same led status show. Also when i press the reset button, in 3 seconds the PC shutdown and restarts. Before yesterday pressing reset was just making the motherboard restart and the leds were blinking once again to show the status change but now no blink on the leds when i press reset.

MSI P35 Neo2-FR, Im having WEIRD beeps in BIOS continiously unstopping.

Oh dear lord, i bought a new board and now im having some stupid beeps going off every 3sec in the BIOS, i updated to 1.8 bios and now its going every 1sec, BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP, every time there is a beep the system hangs a bit, i pretty much cant do anything in BIOS and its getting on my nerves. What is causing this? I tried removing all the drives, my cpu fan is connected to molex not to the motherboard though. In windows they go away, a bit when loading windows logo and it hangs the windows logo too for a few times, then all leds go green, before im getting from top to bottom Green, Green, Green, Red, Green

• Intel Core 2 Quad Q6600 2,40GHz "SLACR G0" + ASUS Silent Knight Copper
• nVidia XFX Geforce 8800GT 512MB GDDR3 + Zalman VF-1000
• MSI P35 Neo2-FR
• 4Gb 2x2Gb A-Data PC6400 800MHz DDR2
• 1Tb 2x500Gb Samsung Sata II
• Seasonic 700W M12 Modular
• Antec Sonata II
Nothing helps, tried butting a fan into the cpu fan slot, nothing, tryed removing PCI cards, nothing, NOTHING helps, it just keeps beeping and hanging on those beeps in the BIOS. When it gets to windows load screen all is fine, the frick.
EDIT: Allright, the answer to this problem is, go to windows and do a restart from windows, go to BIOS and there is no more beeping. I did a save and exit and rewent to BIOS and still no beeping, then did the shutdown and power on to BIOS and no beeps. So, weird problem but an easy answer to fix it. I think its something to do with the motherboard booting for the first time, it just needed to go to windows and make a restart. Weeeeeiiiiird.
Cya, hope this helpes someone in the future.

Msi p35 neo2-fr disable EIST in bios

hello !
My name is Adrian. My system spec.:
msi p35 neo2-fr (bios ver.1.A),
CPU core 2 duo E8400 C0
mem. dual chanel kit 2x2GB geil pristine ddr2 800
2x250 hdd western digital WD2500YS
Video Gigabyte GV-NX88T512HP 8800GT 512 DDR3
Sound Creative Sound Blaster Audigy SE
PSU Chieftec 450W 2x12v: 36 amp., 5v: 25 amp.
OS dual boot windows xp sp3 and windows vista sp2
My problem is when i disable EIST in bios Vista gives me a blue screen (0x0000007F) on boot and XP restarts without any error.
Any idea ? Thank you anticipated !

Quote from: pristine on 11-August-09, 12:31:07
I want to overclock and i want to change the multiplier to make some tests ! And i can`t do that without EIST DISABLED !
OK, stay calm. Getting frustrated is only going to make people not reply.
I'm not sure why disabling EIST is giving you a BSOD. I don't think anyone has any ideas since you have no real replies.
A kernel trap is hardware failure usually. Makes me think when you disable EIST, the machine becomes unstable. Are you setting the default multiplier for your processor? Hell, we don't even know what it is. How about you list your rig specs?
Just to add: Overclocking with EIST enabled is pretty much the same. You save power, so I don't know why you'd want to turn it off, in all honesty.

Need Help with ESATA on MSI P35 Neo2-FR

I have the MSI P35 Neo2-FR motherboard http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=&cat3_no=&prod_no=1261 and trying to get the eternal ESATA to work. It works with one individual HD. I'm using an external ESATA drive with 3 HD inside the external case with one cable running into the external ESATA in the back of the motherboard. It's only recognizing 1 drive and the other 2 isn't showing up. If I switch it to USB connection it will read all 3 drives. I'm running windows 7 x64 but it recognize on my other 2 computers with a different motherboard. I have install it with the ACHI setup in Bios and I've also install the Matrix Storage Controller after installation. I never install the Intel ICH9R SATA RAID driver where you have to press the F6 to install it. Is that what I'm missing and is taht needed for the ESATA to work? I'm getting this message "A storage device was connected. If this device is a port multiplier, only port 0 of the port multiplier will be active." Been googling all day and still can't figure out what I'm missing.
Any help would greatly be appreciated.

Quote
For some reason this board is Bios only have IDE, RAID and ACHI and I don't see a SATA.
IDE, RAID and AHCI are operating modes of the SATA Controller. Everything okay here.
Quote
Seems to me it's either this board and it's driver don't let you use the port multiplier but it suppose to support port multiplier.
It is neither the board, nor is it the driver. It is a limitation of the Intel ICH9R Chipset. You will have the same problem on all P35/ICH9R based mainboards. Read here:
http://xtreview.com/addcomment-id-788-view-intel-technology-matrix-RAID-and-port--multiplier.html
Quote
Unfortunately, used in the south bridges ICH9R the version of such technology provides access only to one hard disk at the specific moment of time. . The technology became more complex to realize , which implies to several access disks simultaneously, possesses higher cost and more higher central processor loads , therefore it can be rejected.
Here is the same problem on a Gigabyte GA-P35-DQ6:
http://forums.overclockers.co.uk/showthread.php?p=11892094
Nothing you can do about it.

Installing MSI P35 Neo2-FR

Hello
I'm installing Q6600 on my MSI P35 Neo2-FR mainboard. In the user guide it says (2-3, 2-4):
- "Make sure that you apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation"
- "Remember to apply some thermal paste on it for better heat dispersion"
- "Meanwhile, do not forget to apply some thermal paste on CPU before installing the heat sink/cooler fan for better heat dispersion."
I'm feeling less confident in installing my Q6600 now without this thermal paste, since it's explicitly *recommended* in the guide. What would happen if I did not apply the paste?

Quote
What would happen if I did not apply the paste?
The heat the processor generates would not be properly dissipated to the heatsink. In a worst case scenario your CPU could shutdown automatically because of overheating and/or be damaged.
Have a look at your heatsink itself. Often thermal paste or some sort of thermal pad is pre-applied for easier installation.
If there is not such thing get some thermal paste before you install CPU+heatsink.

Msi p35 neo2 fr motherboard - system freezes

Hello , I just bought a Msi p35 neo2 fr motherboard and I have this problem . My system randomly freezes ,no errors ,no blue
screens and I have to restart it . I tried each module of ram separately and I got the same problem .
The video card worked fine on my old system and I don`t think this could be . Also the standby led (led 3 ) is always on and red
Maybe I messed up the " wire up " . I could use some tips about how to properly wire up and which settings should be done in BIos for my configuration ?
Msi p35 neo2 fr
PSU Sirtec HPC-430-P12S V2.2
2x1 gb Geil pc6400 800 mhz
video geforce 6200 128 mb
hdd sata 120 gb

from the User Manual:
Quote
Spread Spectrum
When the motherboard’s clock generator pulses, the extreme values (spikes) of the
pulses creates EMI (Electromagnetic Interference). The Spread Spectrum function
reduces the EMI generated by modulating the pulses so that the spikes of the pulses
are reduced to flatter curves. If you do not have any EMI problem, leave the setting at
[Disabled] for optimal system stability and performance. But if you are plagued by EMI,
select the desired range for EMI reduction. Remember to disable Spread Spectrum
function if you are overclocking, because even a slight jitter can introduce a temporary
boost in clock speed which may just cause your overclocked processor to lock
up."

MSI P35 Neo2-Fr -- can't get onboard audio device to appear in XP

I've just installed XP sp3 onto my new mobo (MSI P35 Neo2-Fr).
Attached is Q6600 core2 quad processor, 2GB memory (DDR2), ATI HD4850 gfx card. I haven't changed the bios much at all or overclocked anything yet.
All seems fine *except* that I can't windows XP to see that there's an onboard audio device.
(It is enabled in the bios btw.) I've tried installing the high def audio driver on the CD from mobo box, and also downloaded the latest from the MSI site. I uninstall the driver and reboot before trying to reinstall it again btw.
The audio driver installer used to say there was a problem installing the driver, but it doesn't any more. After installing it and rebooting, XP control panel -> Audio devices says there are no audio devices.
Also, I notice that there should be an extra audio item in the XP control panel (according to mobo manual), but this hasn't appeared.
In XP's system hardware list there are no sound devices under Sound, but there are two unknown PCI devices (with yellow question marks next to them).
Any suggestions?

Quote from: Del UK on 05-September-08, 05:13:05
Had same issue with ATI card installed.
Go to Microsoft update and choose custom
You should see a list with hardware updates..........
After that, all will be fine
Hi there
Thanks for your reply. I went to MS updates, didn't see any in custom about hardware (apart from updated ethernet driver). Installed all updates anyway. And the problem remains...

MSI P35 NEO2 FIR voltage problems!!

Let's start:
I have MSI P35 NEO2 FIR ,e5200,2 x Geil ultra plus 1066+,as us 2900CT,lcpower 6550g and...rest- not so important for my questions.
1.My problem is next: default voltage values for my RAM is ~2.2-2.4 every time I check in windows (speedfun,sisoft Sandra, everest..)shows me 2.0 or some time even 1.8v . When i change voltage in bios and went to win voltage on RAM is still unchanged (2.0v) .
Same thing happen with NB voltage. But CPU voltage I can change freely with no problem.
When I change fsb(try to overclock) suddenly memory voltage rises how i do not now , but only to 2.35 and no more.
Can anyone help me fix this problem because my memory is not stable at 2.0 or 1.8 sometimes and system crashes?
2.When i change cpu settings from 12.5*200 to (example)10*300 in windows even in system properties see that my current clock is 12.5*300=3750 and not 10*300=3000 like it should be .
Is it bios problem?
My bios version is 1.9.
Thanks!

same problem with the Neo2 FR (like mine). After quite of bit of researching and testing i reckon that software can not correctly read the vRAM on these MSI boards. I found that Speedfan, Everest, and HardwareMonitor all gave an incorrect reading for my RAM's voltage. Also, if i increased the cpu voltage in the BIOS then the voltage monitoring programs would show an increase in CPU voltage and RAM voltage (even though i had not changed the latter).

MSI P35 Neo2 Fir Patriot Memory Problems.

Hi,
Having problems with my Patriot Performance PC2-6400 Low Latency Memory DDR2 (800mhz) 4-4-4-12, 2,2v, 2 * (2gb(2*1GB)kit) =4gb total
on a MSI P35 Neo2 Fir moderboard with Intel Q6600 cpu)
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
FSb : Dram 2:3
Cas# latency 5.0 clocks
Ras# to Cas# delay 5 clocks
Ras# Precharge 5 clocks
Cycle Time 16 clocks
Why doesn't they go in 4-4-4-12 frequencys ???
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
Please help.
thanks in advance swefin

Quote
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
~400 MHz is the correct frequency for your modules. CPU-Z shows real clock speed. DDR means Double Data Rate (two transactions per clock cycle). Multiply 399.5 MHz by two in your head and you have your effective DDR(2) rating of 800 MHz. There is no problem here.
Quote
Why doesn't they go in 4-4-4-12 frequencys Huh
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
CL5 is the standard latency for DDR2-800 modules. It ensures that they are able to operate @JEDEC standard voltage settings @1.8V (+/-0.1V). The board is supposed to set memory timings to CL5, otherwise your system would not be able to boot at standard voltage. Check the "SPD" tab in CPU-Z and look for the standard timings that were programmed into the SPD chips of your modules (400 MHz), I am absolutely sure that you won't see 4-4-4-12 @400 MHz @1.8V being part of the SPD tables.
You have to manually adjust memory timings in BIOS to 4-4-4-12 AND also increase memory voltage to the value the manufacturer recommends for CL4/DDR2-800 MHz. The voltage is usually 2.0-2.2V depending on the brand and type of RAM in use.

E8200 Retail with MSI P35 Neo2-FR :

Thought of sharing with the guys here.
Test Setup :
E8200 w/Intel default cooler.
Msi P35 Neo2-Fr Bios v1.1/1.81b
Corsair 6400C4DHX 2GB
Msi 8800GT 512Mb -OC Edition(Red Juliet)
Hitachi 160Gb sata
Acbel iGold 550w
Neo2/platinum Users take note.
If you are on any bios earlier than v1.6.
Do not worry, it will still boot and run fine.
You can always flash the bios later.
Here are results for coolalar.com using E8400 with P35 Neo2-Fr :
http://www.coolaler.com/forum/showthread.php?t=170745
Here's ours, but E8200.
Bios 1.1 works too.
Here are some default results of the processor :
We flashed to Bios v1.81b :
3Dmark06 : Higher cpu score
Cinebench r10 :

Pumped up some video clocks and slightly higher fsb.
511x8, 1.5v
3Dmark06 :
A final validation :
http://valid.x86-secret.com/show_oc.php?id=297680
The 6Mb is nice to have.
But if you are already using an E6750, don't think you will see much difference.
For low volts and operating temperatures,
The 45nm is good.
Ours is good at 3.6Ghz @ 1.25v(bios).
Neo2 users with more results can share here.
http://forums.hardwarezone.com/showthread.php?p=26181870
Cheers! :D

MSI P35 Neo2-FR booting error

Hello all.
The problem I'm having is concerning a MSI P35 Neo2-FR. For about the past year, this mainboard has been used in a Windows Home Server Setup. Not to long ago, we had a power outage (Yes, should have been plugged up to a UPS, Mea Culpa). When the power came back, (and I got home), it couldn't get it to boot. It was doing the old MSI False boot routine that has become infamous. While checking the cables inside, I hit the CMOS reset button while the power was on. Now, I'm not sure how completely screwed I am, but at this point I'm stalled as far as booting at the "initializing keyboard" status light indicator. (Two red followed by a green, then another red, from top to bottom on the LED status light strip). It just hangs there forever. I can't get to a bios screen.
Is there anyway to salvage this?
Oh, and I have an Identical system (different videocard, but same MB, Ram and CPU that went through it, to no ill effects.)
Before it's asked, I have fiddled with the memory (swapped slots, used one stick etc), I have tried booting it with no RAM, no Keyboard, a PS2 Keyboard and a USB Keyboard. All to no avail.

hoho resetting the BIOS while the system is still on is a big sin..I have done the same mistake as u are and to settle this..there's a thing called RMA,u might want to try that

MSI P35 Neo2-FR - Will this work??

Hi,
I am planning a new system, after my current one is a little dated. Here is an outline of what I am planning to build: -
CPU - Intel Core2 Quad Q6600 2.4GHz SLACR G0
M/B - MSI P35 Neo2-FR
RAM - Ballistix DDR2 PC2-8500 5-5-5-15 Unbuffered NON-ECC (4x 1GB)
G/C - INNO3D GeForce 7300GT 256MB DDR2 PCI-E
I am not needing it for gaming, but more for production work (Graphic design, Illustration and video editing).
I have a few questions if anyone can answer them for me?
Is the RAID facility on board a hardware RAID or software RAID. Since its provided by the Northbridge I am pressuming its software.
How many SATA ports can be used at any one time. For example, does using the 2x eSATA ports, reduce the amount of on board ports you can use? (Like some USB ports?).
If I wanted to use a SATA DVDRW connected to the southbridge SATA port, would I be able to boot from it?
I can see many people have had problems with installing Vista on this board, can anyone see any compatability issues with my proposed setup?
Many thanks!!!
Phil

Quote from: Hans Gruber on 28-November-07, 19:07:02
The only compatability issue would be with your 7300gt card. That's hardly enough power to run a game let alone graphics editing. You would be much better served with an 8800gt to perform video editing.
Hi Hans, the 7300 is the same card used in the Mac G5's used in my place of employment for graphic design / video editing. Although some have the 8800GT as well, this is the card used in the majority of the machines. I am sure it will be ok but you reassured one of my existing concerns. I can always upgrade this if it doesnt cut the grain!
Thankyou!!!
Quote from: Maesus on 28-November-07, 19:33:33
Please spend some time to read the moan guide if you haven't.
Yeah not much on there with regards to my post. Cheers but I did read it before I posted.
Quote from: Maesus on 28-November-07, 19:33:33
0. All of your answers are here: http://global.msi.com.tw/index.php?func=proddesc&prod_no=1261&maincat_no=1&cat2_no=170 you just need to read line by line and you shouldn't miss the answers.
was already a bookmark in my browser as I have been researching it for a while now. Just wanted clarification on a few things hence my post.
Quote from: Maesus on 28-November-07, 19:33:33
1. It's ICH9 RAID. It's southbridge, not northbridge. It's hardware RAID.
ICH9 provides a RAID facility is software RAID using Intel Matrix Storage Manager. The CPU processes the parity for RAID 5.
Quote from: Maesus on 28-November-07, 19:33:33
2. you can max up the SATA ports. How many is on this board? 6 SATA ports? you can use them all.
There are 2x eSATA ports (I am pressuming from the ICH9), and 4x SATA on the ICH9, and 1x SATA on the 88SE6111. What I was trying to ask is do the 2x eSATA ports render 2 of the ICH9 ports unavailable?
Quote from: Maesus on 28-November-07, 19:33:33
2a. USB ports does NOT reduce the total amount of USB ports to use, where did you get that info or having that impression??
I worded this completely wrong. My bad..... I have had motherboards before where if you connect a usb back plane to the USB header on the main board, it simply stops you using some of the USB's on the rear panel. This is simply like a redirect to allow you to plug USB devices in to the front of your PC case instead of reaching around the back for it rather than allowing you to add additional ports. This is what I was trying to ask, If I am to use the 2x eSATA ports does that mean that it renders 2x of my onboard SATA ports obselete.
Quote from: Maesus on 28-November-07, 19:33:33
3. Yes
Thankyou
Quote from: Maesus on 28-November-07, 19:33:33
4. it's not really compatibility issue, but more of Vista's own issue, just that you need to do the right step to get Vista installed. Quad Core + 4GB, well, microsoft acknowledge the Vista installation issues with this config. You will need Vista 64-bit, but start installing with 1GB or 2GB. After completing installation, install microsoft quad core and 4GB patches, then only plug in the remaining 2GB.
Thankyou

Msi p35 neo2 fr problem

Alright, I have been using this board for quite sometime and today it gives me problem.
When i tried to boot up this morning, the board just keeps on restarting. This happened once b4 but the problem solved after I pressed on the reset button on the board.
whereas for today, after resetting, the board did stop restarting itself, but it hangs when the LED is at (red, red, green, red)from top to bottom. I refered to the user guide and it shows that there is a problem during memory detection.
Can anyone pls help?
This is what I have
Mobo: MSI P35 Neo2-FR
CPU: Intel Core 2 Duo E6750 2.66 1333mhz/4mb
RAM: Kingston Hyperx 2x2GB DDR2-800
Video Card: Nvidia Geforce 8500GT
HDD: 1xHitachi Deskstar 1TB SATA 3.0gb/s, 1 Samsung 160GB(SATA), 1 Seagate IDE 80GB(IDE)
OS: Microsoft Windows Vista Ultimate SP2
PSU: AcBell 400W DC Output (There are a few of them.. didnt know which one.. the highest is 28Amps)

Okay. About the memory issue: I believe a BIOS Update to the latest version may fix the problem with your DDR2-800 modules. BIOS v1.2, v1.3 and v1.4 had known problems with DDR2-800 modules. In case you decide to do that, please >>Use the MSI HQ Forum USB flasher<< and avoid MSI Live Update or any other Windows based flasher.
About the video card: I is not necessarely defective. Your PSU is not only a low-end poor quality device but also rather weak in the first place. Try a stronger one with your original video card and see if that changes anything.

MSI P35 Neo2-FR Won't Boot From CD

Just received my new board which aside from the problem, is fantastic! It's an MSI P35 Neo2-FR
I've got DVD drive to first in the boot sequence and it prompts me to press any key to boot from CD however when I press any key it just hangs on press any key. Got some advice from a friend and he told me to load optimized defaults however it doesn't make a difference.
Help?

Quote from: Sharp on 24-February-08, 00:09:47
Hello,
Could be a few things.
Make a list of everything that you are using with the board so that we know what you have.
EG, look at the bottom of my post.
Do you have a floppy drive?
http://www.memtest.org/download/2.01/memtest86+-2.01.floppy.zip
- Extract all the files to a folder.
- Run the install file and it will create a memtest boot disk for you.
- Then boot from the floppy disk and let the program run for a while (4 hours+)
- If it detects any errors instantly stop and report back here. (or try 1 stick at a time)
CD or USB versions available here.
http://www.memtest.org/#downiso
But it is important that we know what else you are using with the board.
Could be a weak power supply or you are using different branded memory modules.
And did you plug all the power connectors into the board?
- 24pin ATX
- 8pin +12v EPS connector
- Molex near the first PCIE x16 slot.
Just incase this thought has crossed your mind,
Do not attempt to the flash the BIOS until you know the system is 100% stable/working
Molex near PCI-E X16 slot? I didn't plug that in no. What's it for may I ask?

MSI P35 Neo2 FR beta Bios 1.72

Similar Messages

Maybe you are looking for