Mute button, low volume button and high volume button not working after upgrade to Win7 Pro

Hi all, Im using X301. Previously it was shipped with the Vista Business. I was entitled for free upgrade to Win7 since the thinkpad was bought after 25th of June 09. The problem started after I successfully upgraded my Vista to Win7 Pro. My Mute/Unmute button was consistently in amber colour (signal for disabled). the volume button also is not working anymore. On the system side, everything was fine. the drivers is working properly.. the windows also is showing the volume is in a good shape. Unfortunately the button on the thinkpad is always on the disabled mode. Ive been searching for a related drivers that i could download and solve the issue. but till now all the softwares and drivers downloaded from lenovo could not solve my problem. any suggestion or comment is highly appreciated. thanks a million

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:       
iOS: How to back up
- Restore to factory settings/new iOS device.
-  Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
When iOS 6.1 comes out I would update.

Similar Messages

  • Wecam and USB mic input not working after upgrade to Lion

    The audio inputs (micraphones) all show up in Syetem Preferences but if I talk into the microfones (on USB soundcard/Trust Webcam) no levels are  being shown, I have tried clicking on eatch input it turh but n luck.
    I am getting the impresion Lion broke lots of audio atuff so dont hold up mutch hope for a solution (Except upgrading to Snow Leperd).
    Any ideas,
    Ben

    Beginning with Leopard, Mac OS X supports the so-called UVC web-cameras, you do not need any driver for them. I have just bought a small, pretty and cheap one, Logitech C110.
    My older Genius 1321 is unfortunately unusable from SL onwards, but works with Tiger and Leopard. It is not UVC, and drivers are not available any more.
    conclusion: if your camera is not UVC will not work via ‘plug-and-use’, you need an updated driver, check with the manufacturer. If they do not offer any, buy a UVC one, they are very cheap, but you do not need anything. The one I have just bought works fine, and also has internal mic.

  • [SOLVED] raid1 and luks/dm-crypt not working after upgrade

    hello folks,
    i just made a pacman -Syu, which also updated mdadm and cryptsetup (not the kernel). but after a reboot, the system didn't boot any more. after #'ing the cryptsetup-relevant lines in /etc/crypttab and /etc/fstab, the system booted again. after a check, i get those messages:
    ~ $ cat /proc/mdstat
    Personalities : [raid1]
    md1 : active raid1 sdd1[0] sde1[1]
    390707641 blocks super 1.2 [2/2] [UU]
    md0 : active raid1 sdb1[0] sdc1[1]
    1465134841 blocks super 1.2 [2/2] [UU]
    unused devices: <none>
    ~ $ sudo cryptsetup luksOpen /dev/md0 data
    Passwort:
    Geben Sie den Passsatz für /dev/md0 ein:
    semid 65537: semop failed for cookie 0xd4d2ffb: incorrect semaphore state
    Failed to set a proper state for notification semaphore identified by cookie value 223162363 (0xd4d2ffb) to initialize waiting for incoming notifications.
    what happened and how to fix it?
    i didn't change anything. so it shouldn't be anything about modules or whatever.
    EDIT: okay, it's not aboud the raid, but about the cryptsetup version. see below.
    Last edited by _abraxas (2011-01-28 11:18:34)

    SOLVED!
    It works again with the new version of the device-mapper: 2.02.81 (no unknown semaphore state anymore).
    But also the crypttab syntax has changed. After removing the options in crypttab, cryptsetup 1.2.0-1 works again.
    Old crypttab file:
    # NAME     SOURCE DEVICE     PASSWORD     OPTIONS
    #home     /dev/sda4     ASK     -c aes-xts-plain -s 512
    #data     /dev/md0     ASK     -c aes-xts-plain -s 512
    New crypttab file:
    # NAME     SOURCE DEVICE     PASSWORD     OPTIONS
    home     /dev/sda4     ASK
    data     /dev/md0     ASK
    Have a look at https://bugs.archlinux.org/task/22351

  • Iphone 4 Home button not working after upgrade to OS 4.3.5

    Iphone 4 Home button not working after upgrade to OS 4.3.5.Please help!!!!!!!!

    It seems that settings of mail accounts have something to do with it. I've delete my gmail account and am now using Microsoft Exchange. It seems better, yet not perfect. The issue is definitely due to OS 4.3.1
    Apple answer is - no answer. It is a shame that the quality of their products, in terms of design and concept, is not match by a care for customers. It is not normal that I, as a customer, have to spend hours reading Apple Discussions forum to try to understand what the problem is. A little more respect for a customer that spend big $$$ buying their products wouldn't hurt.

  • TS1702 My app store, Apple ID, safari, and most other apps do not work after upgrading to iSO 6, How do i solve this problem?

    My app store, Apple ID, safari, and most other apps do not work after upgrading to iSO 6, How do i solve this problem? Can somebody help me please?

    The App store is a problem for many and I have not seen a solution.
    What is "wrong" with your Apple ID?
    Try the following:
    - A reset. Nothing is lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup
    - Restore to factory settings/new iPod.

  • Security and privacy system preferences not working after Lion install.  What to do?

    Security and privacy system preference not working after Lion install.  Not sure if it happen with Lion installer or after updating. What to do?

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
    These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
    Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
    Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
    Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
    Launch the Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Terminal in the page that opens.
    When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” (without the quotes) and press return. You should then get a new line ending in a dollar sign.
    Step 1
    Copy or drag — do not type — the line below into the Terminal window, then press return:
    kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
    Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
    Step 2
    Repeat with this line:
    sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}'
    This time, you'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up. You don't need to post the warning.
    Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
    Step 3
    launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
    Step 4
    ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
    Important: If you synchronize with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
    Step 5
    osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
    Remember, steps 1-5 are all drag-and-drop or copy-and-paste, whichever you prefer — no typing, except your password. Also remember to post the output.
    You can then quit Terminal.

  • Bookmarks and reading lists don't work after upgrading to ios6 on ipad

    Bookmarks and reading lists don't work after upgrading to ios6 on ipad

    Your bookmarks file may be corrupt. Navigate to /[UserName]/AppData/Local/Mozilla/Firefox/Profiles/[profile_name]. Either rename places.sqlite to places.sqlite.corrupt (or whatever) in case this isn't the problem, or delete places.sqlite. Start/Restart Firefox. The icons for sites that have a favicon should return after you visit each site.

  • IPhone Home Button not working after upgrade to ios 5.1.1

    Hey everyone,
    I'm pretty sure this is a software failure due to the symtoms the iPhone is showing;
    0 - the home button does not work at all when the phone is turned on and running ios 5.1.1, well it used to work okay when i had ios 5.0.1, I upgraded to 5.1.0 and started working randomly, upgraded to 5.1.1 to see if it was fixed with no luck at all.
    1 - When locked the screen does sometime light up, like when you press the home button and don't slide the unlock button. but it does not exit apps anytime, I mean it doesn't act like it's pressing the home button randomly but only when the phone is locked.
    2- The button does work perfectly when iOS is not running: I can get in and get out of recovery and dfu mode at will, that wouldn't be possible if the button were broke.
    3- what else? Oh yea, not really a symtom: Tried the 'home button calibration' several times.
    4 - It's not filthy, since I really cleaned it thoroughly with a powerful tiny nozed air blower I got and gave a rubbing alcohol treatment too.
    5 - when I shut the phone down it instantly turns back on, I can interrupt the turning on for turning the phone into dfu mode (i'm sure It's in DFU mode because the tinyumbrella log monitor tells me)
    I'm now using the 'soft' home button that goes in the accesibility options, but hey, I didn't pay a ton of money for a phone that the same Apple is gonna break down.
    It's out of warranty and I don't have apple stores where I live.
    I'd downgrade to 5.0.1 in a snap if I could but I'm not into jailbreaking, so the shsh blob thingie is not a possibility.
    Any apple dev around that can give me a workaround?
    thanks a lot in advance
    Added more info ~ 

    I had the same problem with Home button not responding after upgrading from iOS 5.1 to iOS 5.1.1 on an iPhone4.   I solved it but not sure exactly what fixed it.   Here is what I did.
    1.  Took it local Apple store Genius appointment.   They used a special tool and took some lint out of the connector opening.   The Home button started working.   They said even though the phone was out of warranty, I could buy a new replacement one without a contract for $150. 
    2.   The Home button stopped working when I got home.   I got some compressed air in a can and blew the air through the connector to try and clean out more dust.   I now keep the phone with the connector opening facing down in my pocket.   I also struck the phone downward on my hand or other soft surface to force as much dust out as possible.
    3.  The Home button still was intermittent.  I then tried to do a hard reset by holding the power on key and the Home button simultaneously for about 10 seconds.  This doesn't work if the Home button doesn't respond.
    4.  I connected the iphone to Itunes via the USB to sync the phone.  While connected, I did a Hard Reset by Holding the Power button and Home button simultaneously.  I noticed the Home button responded better when connected to ITUNES via the USB.
    5.  I did a backup of the iphone4 by highlighting the iphone 4 while connected to ITunes and right mouse click and selecting BACKUP.    I was prepared to reset my phone4 in iTUNES and restore it from the backup.
    The phone worked consistently before I had to do this.
    6.  As a last resort which I didn't need to do, I was going to copy all my settings for the iphone by selecting the phone in iTUNES and looking at all the sync settings.   I would then have restored the iphone to original factory settings and then sync the phone using the copied settings.  This would have made sure that the backup didn't include the bug.
    Fortunately, I didn't have to do step 5 and 6.   Things started working after Step 4.  So I don't really know if it was the iOS 5.1.1 upgrade or pure coincidence that the Home button stopped working immediately after the upgrade.

  • Ipod touch home button not working after upgrade

    Hi,
    The home button on my 1st generation ipod touch stopped working after upgrading the software a couple of weeks ago. Has anyone else come across this issue? Is it possible to downgrade the software? I have tried restoring the ipod with no luck.
    Thanks

    HI there,
    thanks for the reply. Tried both of what you suggested, also tried the home button thing only working while plugged in with two computers and two different leads which is why I suspect is an operating system thing.
    I may try downgrading the operating system next, just have to find a copy of an old one somewhere.
    Cheers,
    Martin

  • IPad 2 front and back camera is not work after update iOS 7.0.4 it gives like the resolution is not adjusted

    After updating my ipad 2 to iOS 7.0.4 , front and back camera is not working it gives like very small dots or dash. I did restore from iTunes and reset by holding on the home and sleep button, I also tried to close the app from the task bar but still all trials didn't solve the problem.

    I haven't heard of this before so I doubt it's a bug. Probably something happened during the 7.04 download.
    Backup your iPhone to iTunes and restore it as a new iphone, then restore from the backup. This will give you a fresh copy of iOS 7.04.

  • Windows 10 - No sound and mediaplayer does not work after upgrade

    Hi !I can't get the sound to work after upgrade to win 10, - and windows mediaplayer will not openmp3's -- I get video on the VLC - but no sound... If anybody can help me, - please post a direct link to the driver I have toreinstall.. Thanks  CarstenNorway

    Thanks for the answer-  but I mangage to solve the problem my self this time... I just did go to controlpanel - and clicked right button on the mouse - and updated both sound drivers thatI did find in there. After restart of the lap - everything worked ut well.. I am supprized !!  Carsten

  • Upgrade of our 10.4.11 laptop to 10.5 is accomplished and we now need to upgrade Quicktime and iTunes; however, the user name and password is now not working after the upgrade to 10.5.

    Object is to sync address and calendar between laptop with Max OS 10.4.11 and iPhone. Upgrade of our 10.4.11 laptop to 10.5 is accomplished and we now need to upgrade Quicktime and iTunes; however, the user name and password for the laptop is now not working after the upgrade to 10.5., though it was working prior to the upgrade, for file sharing.

    @ BDAqua > I tried your suggestion but no luck. holding opt+command just gave me a blue screen and it rebotted, pushing the disk out of the drive. Yes, the macbook has 1 gb of ram. I realize that the min req. call for 2 gb of ram so i've got an order in for another dimm to put into the machine. Thanks for your suggestions.
    @ a_brody > Yes. The machine was plugged into a power source. The disk promts you to do that and i recall aspect this form other installs. Thanks for the reminder tho! ( btw your second post is like greek to me man!) 
    @ Kuncklesmac > You're right about Snow Leopard being an upgrade from Leopard. I'm aware of this. And yes previously i've been told by Apple that I needed the Box Set (not the family pack.  i am using the family pack for OS Snow Leopard) to upgrade my 10.4.11 mac - they never mentioned adding ram but i figured that out on my own and an apple specialist recommended it when i purchased Snow Leopard and confirmed that I coul duse the Snow Leopard to upgarde from Tiger (10.4.11). I've also read extensively (as i said above) that it isn't necessary (always) to buy the box set. Several 10.4.11 users report having upgraded using the Snow Leopard upgrade disk only (not the Box Set) without trouble on intel macs (also see the apple link i posted). So i'm just ondering how they did it and i cannot. 
    Thanks fo rall yor help!

  • Keyboard delete and caps lock keys not working after update

    Shortly after a windows update two keys, delete and caps lock do not work. I have tried the following
    1. system restore..it says it cannot restore as a file is missing. I have used this function before without any problem.
    2. Update key board driver (standard PS/2)..it says latest version is installed.
    3. Uninstall and reinstall.
    4. Reset using the remove batteryt hold down power key option.
    The caps lock and delete does not work in Notepad or MS Word.
    It seems unlikely that the two keys themselves are damaged as it is unlikely that they would both fail at the same time and the problem after the windows undate is suspicious.
    I am using Windows 7 Home premium on a 64 bit HP G62.
    help appreciated as ever
    thanks
    matyiii

    matyiii wrote:
    Thanks I am beginning to suspect the same thing. I will try keyboard replacement as a last resort.....no fun to buy a new key board and have the problem persist...
    regards
    Matyiii
    Here's another test...since your laptop has USB ports get or borrow a USB keyboard and try it and if all those keys work and test then the results would mean your laptop keyboard has stop functioning as least you narrow done the problem.
    I am a Volunteer to help others on here-not a HP employee.
    Replies aren't online 24/7 because of Time Zone differences.
    Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

  • Itunes does no play and music line does not progress after upgrade

    itunes does no play and music line does not progress after i upgraded my itunes to 11 version

    The same thing for me and I've tried EVERYTHING. Someone please help!?!?!

  • 11.1.1.6.4 Repository variables for DSN and USER do not work after upgrade

    Hi,
    The Repository Variables OLAP_DSN and OLAP_USER no longer work after upgrading to 11.1.1.6.4 i.e they return a connection error when trying to import metadata but the connection is correct if explicitly set without the variable used.
    I have tried the following resolution:
    - From command line execute commands to set variable properties via admintool.exe /command vartext.txt
    Open rpdname user password
    SetProperty "Variable" "OLAP_DSN" Initializer "'ORCL.GLOBAL'"
    Save
    Close
    Exit
    This script works fine as demonstrated by commenting out Save, Close, Exit and running. But it does not resolve the problem.
    The issue is consistent as in the OLAP_USER variable does not work if DNS for connection pool set to ORCL.GLOBAL.
    Is this a bug?
    Thanks in advance
    Edited by: 983325 on 26-Feb-2013 02:35

    There is a 3.1.0.5 client. First thing I would try is the newest client.
    Sent from Cisco Technical Support iPad App

Maybe you are looking for