My airport express is not connecting with my airport extreme base station. They are probably six years old. My IP address on my express shows 0.0.0.0

My Airport extreme and my airport express are not connecting together. I get an error message saying that my airport express software is not compatible with my Airport extreme and I have use them together for the past five or six years. It says I may need to change my IP address on my computer or something like that but I don't know what to do. the IP address on my express shows 0.0.0.0. Should everything be on the same IP address? Any help would be greatly appreciated. Thank you

Please refer to the information already posted above:
If you see A1084 or A1088 there, your older Express is not supported by the newer version of AirPort Utility that you have.
If you have another Mac running Leopard or Snow Leopard, or a PC, then you could use that computer to administer the older Express and it will work on the network along with the AirPort Extreme.
If the Mac running Leopard or Snow Leopard or PC does not "see" the A1084 Express, you will need to "hard reset" the Express by holding in the reset button for 10 seconds and waiting a full minute for the Express to restart. Then, reconfigure the Express again.

Similar Messages

Current version of airport utility will not connect with older airport express

I was given an older aiport express that I want to add to my network for iTunes sharing. I have an airport express and aiport extreme currently. I am running Mac OS x 10.7.5. My current version of airport utility does not support this express and it tells me to download utility version 5.6. When i try to install version 5.6 i get an error message that tells me to contact software manufacturer. I'm sure there is a simple fix but I don't know what to do. Any help would be great!

Hi
again , at least for getting 5.6 installed, look at my post earlier, or better to JEFFY's and download an much better alternative "unpkg", to get it ( 5.6) on to your mac.
Then, though, getting to use it to configure your older AP as I attempted is anothe matter. I didn't succed so far..
Good luck to you. If it works pse tell .
Thanks.
Pierre

My system can not connect with the Airport Express while the signal is very good?

Neither my phone nor my desktop (windows 7) can not make a connection with the Airport Express. The signal keeps flashing amber.
Several specialists have checked but can not solve this problem. Any ideas?

I am in exactly the same boat...

AirPort Express - Can not connect to "extended" AirPort Express

Two trips to the Genius Bar tell me that I should be able to Extend my network from a new AirPort Express (n/g/b) to an older AirPort Express (b/g) using the "extend network feature". The two devices are communicating (both lights are green and the wireless channel will change on the remote device if I change it at the base station), but my MBP Core Duo 15" seems to only be connecting to the AirPort Express Base Station (n/g/b) and not to the Remote "extended" AirPort Express (b/g).
This forum seems to indicate that you can only use WDS between the newer AEX (n) and the older AEX (b/g) but the folks at the Apple Store have told me twice now not to use WDS. They said that as long as the two devices have green lights that it is working, but when I click on the Airport Symbol up in the menu bar w/the Option key it tells me the MAC address of the base station only - and when I get very far from the base station, the signal drops out even though the remote AEX is near by.
I did try setting it up using WDS and that works fine, just very slow.
Anyone know if there's a way to be sure that my MBP connects to the remote (extended) AirPort Express?

This forum seems to indicate that you can only use WDS between the newer AEX (n) and the older AEX (b/g)
This is correct....since the older b/g Express does not even have a setting to "extend a wireless network".
If you require confirmation, open AirPort Utility, select the b/g Express, click Manual Setup
Click the Wireless tab below the row of icons
Now look at the available settings for Wireless Mode.
"Extend a wireless network" is not there.
but the folks at the Apple Store have told me twice now not to use WDS.
They are likely telling you not to use it because the performance on your network will drop dramatically if you do use WDS. Or, they mean well, but they are just wrong on this subject. Here's why:
The only way that you can use an older "g" and newer "n" device together to provide more wireless coverage is to configure both devices for WDS. It's a Catch 22.
WDS operates only at "g" wireless levels. So when you configure the newer "n" Express to operate as part of the WDS (which you must), it becomes a "g" wireless device. You lose any "n" capability on the network
Worse still, every "remote" or "relay" in a WDS setup cuts the bandwidth of the entire network in half...50%. That's huge. In effect, with WDS, you may have a bit more wireless coverage, but you will have a "g" wireless network that operates at half speed.
but when I click on the Airport Symbol w/the Option key it tells me the MAC address of the base station only - and when I get very far from the base station, the signal drops out even though the remote AEX is near by.
The remote AX is not providing any additional wireless coverage.
They said that as long as the two devices have green lights that it is working
Nope, as you can tell by the fact that your "remote" is not providing any additonal wireless coverage.
Anyone know if there's a way to be sure that my MBP connects to the remote (extended) AirPort Express?
Your only option, (unless you add more hardware):
Configure both AX devices to "Participate in a WDS network" setting one up as a "main" and the other a "remote" . The big downside, as mentioned previously, is that you will have a "g" wireless network running at half speed.

Express will NOT connect to CHANNEL #1 on BASE - HELP?

12-1-05
Please help or advise, at the end of my rope here.
New Apple Express, set to "join existing network", using for Airtunes into stereo in next room. Battleing the drop-out problem well reported in other thread.
Living in an apartment in a busy city, I see at least SIX other networks in iStumbler, half on Channel #6, the other half on Channel #11. Even though my Buffalo G54 WAP (wireless access point connect to DSL modem) is right behind my G4 Titanium, the other networks have almost the same signal strength I'm seeing. I can stream the audio on CH #11, but with the drop-out audio problem much of the time, so my GOAL, was to switch the Buffalo to Channel # 1.
PROBLEM: I have done the procedure very many times in two days, including even doing the "hard" reset of the Express unit. Have used both Airport Admin Utitlity, as well as Airport Setup Assistant, etc. I can switch the Buffalo WAP to CH #1 no problem, and get online same as always. But have NOT once been able to get the "green light" on the Express, and nothing on the computer can see the Express at all, rebooted etc. Just will NOT connect as long as the WAP is on CH # 1.
Back to Channel #11 on WAP, the Airport Express connects and works like before. ANY CLUES WHY I CAN'T CONNECT TO the Apple Express uing CHANNEL # 1 ???
I've tried everything I know at this point, channel one looks like a strong signal here, but so far have been unable to try it for Express Airtunes streaming. THANKS!

I'm not sure about cable connection but I've recently connected to Bigpond using one of their Siemens ADSL modems connected through my Airport Express.
Bigpond help desk were very helpful and suggested that I needed to reset the DSL modem to Bridge Mode, instructions were obtained from the Siemens website. After you have printed off the instructions. First reset your router without your Airport connected and ensure your router is working correctly in Bridge Mode.
Enter the URL address http://10.0.0.138 at the top of your browser for Bigpond and login with Username "admin" and Password "admin" then follow the steps you have printed off.

HT4796 Migration assistant is telling me that it has lost connection with my Mac and to ensure they are on the same network. They are, and an ethernet cable is plugged into them. What do i do?

Migration Assistant has been running since yesterday evening. My Dell is now telling me that its trying to reconnect to my Mac and to ensure they are both using the same network. I have an Ethernet cable plugged in them and they are both on the same WiFi. What can I do?

Hello Wyodor,
thanks for your reply on my question.
You are wright the index file is 308 KB.
And offcourse that I delete my files and documents is not an Iweb problem, but because my English is not that good, that I thougt I try to tell the whole story, and hope people can read trough the lines.
Why I didn't use Iweb to upload to the server is because the server company recommanded to use file zilla. And I am a nobody with this kind of things, so I did exactly what they tell me to do.
No, i did not make a backup of Iweb and the domain file, but reading other messages on this forum showed me that I can maybe try to make empty the cashfile (?)
and otherwise I have bad luck and have to make my website again. Offcourse I have a lot of examples from all the pages (copied from the local map to my USB stick) and my website is aprox. 15 Mb, (not so big) so it will cost me a few nigths.
But I'm still hoping on a miracle :-)
greetings Lasource

My iTunes Match not add my songs to my iPod touch that I have on my external hard drive I had this drive for 3 years now ain't notting wrong with my songs on it but they are not been added to my iPod why is this so plz fix this or iTunes Match gonna suck

So I sign up for iTunes Match an start adding music to my iPod touch 5 generation I have a lot of music on my hard drive that I had for over 3 years now but some reason they are not syncing to my iPod touch notting is wrong with my music some may not have a track name but they r fine. Note ,before I added iTunes Match to my iPod I could of synced my music with no problem , so can u guys plz fix this ? Why can't my music be added to my iPod ?iTunes don't have all the songs I want I have my own music before iTunes so I don't understand why can't I have them on my iPod touch 5gen ?

Hi,
What is the iCloud status of these tracks?
You can add icloud status column to song view - go to menu > view> view options and tick box. This will tell you what has been Matched, Uploaded, Purchased, Inelligible, Duplicate or Waiting.
Jim

Itunes will not connect with my airport express

My new macbook will connect automatically to my airport express network with airtunes but the itunes on my imac will not. It show the network as an option for additional speakers but when I choose the airport express network as my external speakers it gives me a box saying it is connecting then after a few minutes it just goes away and reverts to the computer for my speakers. Any ideas on what to do? The aiport express has the latest firmware update.

Check the Firewall settings in the Sharing area of System Preferences.
I think you need to have iTunes Music Sharing enabled (maybe not).
Ian

Express will not connect to network after Extreme firmware upgrade to 7.2.1

I got the auto update notice for a fimware upgrade to my Extreme to 7.2.1. Once I upgraded I am no longer able to connect my Express. I have done all the resets and have gone through all configuration each time, but after it resets itself after configuring it, it no longer shows up in the AirPort Utility until I reset it again. The only thing unique about my Extreme config is that I have the Radio Mode set to 802.11b/g compatible. This was necessary to connect TiVo wireless USB adapters to the network.

I can tell you that you are not alone - I have tried to crack this one for some days - Im just following the instructions from the Airport assistant and it dosn't work

HT4743 why are TV series not available on Itunes when they are over 2 years old and are available with Netfox & Lovefilms, E,G The Americans series 1 but not 2 or 3, Revenge series 1 & 2 but not 3. can anyone help were I can download them please

Itunes is not up to date with these series, Revenge series 3 and The Americans 2 & 3, can anyone help were I can stream this to my Mac or ITV please

It is up to the content owner as to when, and if, specific content is available on itunes (or any outlet for that matter). Very often a network or production compnat willhave exclusive deals with streaming outlets for a period of time before a seaon of a series is available elsewhere.
I can't speak to most of the shows you reference, but in the case of The Americans, there has only been one season so far. Season two isn't schedule for broadcast until February of next year.

Airport card does not work with Airport Extreme when security is turned on

I have an iMac running OSX 10.4.11 with an Airport card installed (firmware version 9.52).
I recently replaced my Netgear wireless router with an Apple Extreme Base station and now I am not able to connect my iMac to the wireless network when WEP security is turned on - I get an error from the Airport Setup Assistant when I attempt to connect to the wireless network.
It works fine if the wireless security on the Extreme Base station is turned off.
Please help and thanks in advance.
Motasim

First, I highly recommend that you switch to either WPA or WPA2 as WEP is no longer considered secure. If you must use WEP, I suggest that you try the following:
o Re-create the Network Name (SSID) on your AirPort Extreme Base Station (AEBS)
o Try using 128-bit WEP, with a 26-Hex character key for the encryption type.

I have a ipad 2 and it does not connect with safari using 3G

I have a ipad 2 and it does not connect with safari using 3G

Sorry to hear you are having issues, but there are 2 ways you can print from that device.
The first one is to simply email photos or documents to your printers email address by attaching them to a new message.
The other option is to download the HP ePrint Home and Biz app from Google Play. The app is free and should allow you to print pictures and documents to the printer with ease. I have added a link below on how to get started with this app.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01616126&lc=en&cc=us&dlc=en&product=3857218
Jon-W
I work on behalf of HP
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
Click the KUDOS STAR on the left to say “Thanks” for helping!

Airport Express Transmits To Airport Extreme Base Station Intermittently

I have an Airport Extreme set up as my base station wirelessly.  I also have an Airport Express set up to extend the range of my network.
The reason I have the air port express is that the walls of my house are very thick, so I thought that if I have an Airport Express, then I can jump the signal from one signal strength room to a week signal strength room.
The length of the house is within the 30m range.  Airport Utility occasionally can not see the AExtreme or AExpress but if I put both in the same room it picks both up.   At the low signal strength end of the house my MacBook or MacBook Pro Air Port Utility only picks up the AExpress located at this end of the house.  If I restart the AExpress then Airport Utility picks up both airports in the week signal room, then the Extreme drops out.
Q1 - Why does this happen i.e. only showing the nearest / clearest signal air port?
What I have established is that the connection to the internet is always through the wireless signal from the AExtreme (ADS Router connected directly to this).  I established this by switching off the AExpress at the week signal end of the house and finding a spot where the signal could be picked up.
Q2 - If the AEtxreme and AExpress are within the nominal 30 m range why cant my lap tops just pick up both Airports on Airport Utility.
Q3 - Can you set up both Airports such that one will boost the signal and if so how.
Q4 - When running AExtreme only why does the signal strength vary - even when sitting right next to the extreme?
Thanks
Alastair

On this same topic;
We have a new Extreme base station that connects 1 MBP, (wirelessly), 1 HP Laptop (wirelessly) and 2 PC (via ethernet) to the internet.
All of the computers can see and use the Extreme base station and the printer connected to it via USB.
We also have an Airport Express that the two laptops can see. This has a printer connected to it as well via USB. (both are new Canon printers and all of the software for each, and their drivers are loaded on all computers).
Both the Extreme and Express have a steady green light, their own names and are set up on the same network.
Though my MBP can see both the Extreme and Express, neither "see" each other as far as I can tell. And, the printer connected to the Express cannot be seen in either Bonjour Printers, or anywhere else.
Also, in order to "attempt" to find the printer connected to the Express, I have to disconnect from the Extreme Base Station and connect to the Express.
How can I get the printer (connected to the Express) to show up in my pick list of printers WITHOUT having to disconnect from the Extreme and connect to the Express. Also, how can we get the Express to be connected to the internet via the Extreme?
All searches here and documents I have poured though do not address this issue and we'd really like to get this straightened out. I am willing to take a lot of time to do this, but do it right.
Can someone please help me with this?
Thank you in advance,
~ J

Adding an Airport Express to an Extreme Base Station

I have an Airport Extreme Base Station and it has been operating for several months, I decided to add an Airport Express to extend the range and it appeared that it was a simple process. NOT. The Express instructions indicated that when downloading the software to follow the instructions on setting up a network but it will not get that far in that I get an error message telling me I have a newer version of I Tunes and it stops the install. I have gone through the tech support pages here and am at a loss on how to get this connected. Can anyone help provide me a step by step method to do this? Thanks

On this same topic;
We have a new Extreme base station that connects 1 MBP, (wirelessly), 1 HP Laptop (wirelessly) and 2 PC (via ethernet) to the internet.
All of the computers can see and use the Extreme base station and the printer connected to it via USB.
We also have an Airport Express that the two laptops can see. This has a printer connected to it as well via USB. (both are new Canon printers and all of the software for each, and their drivers are loaded on all computers).
Both the Extreme and Express have a steady green light, their own names and are set up on the same network.
Though my MBP can see both the Extreme and Express, neither "see" each other as far as I can tell. And, the printer connected to the Express cannot be seen in either Bonjour Printers, or anywhere else.
Also, in order to "attempt" to find the printer connected to the Express, I have to disconnect from the Extreme Base Station and connect to the Express.
How can I get the printer (connected to the Express) to show up in my pick list of printers WITHOUT having to disconnect from the Extreme and connect to the Express. Also, how can we get the Express to be connected to the internet via the Extreme?
All searches here and documents I have poured though do not address this issue and we'd really like to get this straightened out. I am willing to take a lot of time to do this, but do it right.
Can someone please help me with this?
Thank you in advance,
~ J

OS X 10.2 w/ Airport Card Connecting to Extreme Base Station

Hey--
I'm on a G3 Powerbook (w/Firewire) running OS X 10.2 and I installed an Airport Card and I'm trying to connect to a new Extreme Base Station-- and PB can't see the Base station in the Airport Utility. Although my PB does receive the signal from the base station.
I've tried:
- Resetting the base station
- Loaded Airport 2.1.1 software update
- a million configurations
- yelling at it...
The airport card does work, because it connected on another wireless system.
Can someone help me with the definative fix?
Mike

Welcome to the discussion area, stacidesign!
First, you have verified that the PC can connect to another wireless network, correct? If it can, then that tells you that the wireless card is functioning correctly.
You'll have better luck connecting to a newer wireless router if you are able to update the PC to Windows XP SP3. Have you tried this?
It's also possible that the wireless card in the PC can connect to a 802.11 "b" or "g" network, but not to an "n" network. To check that out, you need to use AirPort Utility - Manual Setup to make a change in the radio mode of the AirPort Extreme.
Click the Wireless tab below the row of icons
Hold down the option key on your Mac while you click on the Radio Mode selection box
Write down your current settings so you can return to them later if needed
Select this Radio Mode...+802.11n only (5 GHz) -- 802.11 b/g+
Keep the Wireless Security set to "None" temporarily
Update to save changes and allow 30-40 seconds for the AirPort Extreme to restart
Restart the PC
See if the PC can connect now
Please post back on your results
Message was edited by: Bob Timmons

My airport express is not connecting with my airport extreme base station. They are probably six years old. My IP address on my express shows 0.0.0.0

Similar Messages

Maybe you are looking for