My Application gets Error 37 when using Serial Port VIs.

My Application works fine developed with LV 6.1. Then I updated to LV 7.1 and now the Executable of my application gets error 37 when using the old serial port functions. The "serpdrv" file is located in the application directory and is from 02/2002. The application runs well in the development environment after I placed the "serpdrv" file in the LabView directory. I tried to put a line with "serialDevices=..." in the .ini-file of my application but this did not cause an improvement. I also tried to rebuild the EXE with this line in the "labview.ini" file but nothing changes.
Does anybody have another idea ?
Many thanks for help
Thomas

>Did you actually replace the old serial functions that come with 7.1 with the functions from 6.1?
Yes. E.g. "open serial driver.vi" uses "open device" with "serpdrv" as device string.
I had the same problem running my application as VI´s. After the copy of serpdrv into the LV 7.1 directory everything works fine.
I don´t understand why the application running as a .exe doesn´t find the serpdrv when it is in the same directory....
Nevertheless many thanks for your answer
Thomas

Similar Messages

Error 37 using serial port with an executable file

Hi all,
I have developed a VI that controls a setellite receiver using RS232
serial port (LabVIEW 5.1.1).
The VI program run properly, but when I compile it and try to run the
executable file I receive an "Error 37, Device not found" error message.
I have already put serpdrv and my_file.ini files in the same directory
of my executable program my_file.exe, but I have not been able to solve
the problem.
Any help greatly appreciated.
Regards
Antonio
Sent via Deja.com http://www.deja.com/
Before you buy.

[email protected] wrote:
>
> Hi all,
> I have developed a VI that controls a setellite receiver using RS232
> serial port (LabVIEW 5.1.1).
> The VI program run properly, but when I compile it and try to run the
> executable file I receive an "Error 37, Device not found" error message.
> I have already put serpdrv and my_file.ini files in the same directory
> of my executable program my_file.exe, but I have not been able to solve
> the problem.
> Any help greatly appreciated.
>
> Regards
>
> Antonio
>
> Sent via Deja.com http://www.deja.com/
> Before you buy.
Maybe you used the serpdrv from an older version of LV
Regards, Roland
Roland Lampka - Nortel Dasa - ESN 565-7257 - FAX 8160

New install of SQL Server 2012 x64 Express on Windows 2008 Server, keep getting error when using Management Studio?

After installing the x64 with all tools excluding the SDK from the SQL Express Edition, I go to Management Studio, log in and get the error when I click under the Instance name- Databases...Have reinstalled many times, removed all directories and registry
keys from both HKEYs(regular and Wow6432Node) before rebooting and reinstalling. No VS installed on this computer..put it looks like it installed "MS Visual Studio 2010 Shell (Isolated)-ENU" and "Visual Studio 2010 Prerequisites".....tried working past
the error, it just hangs the Studio after it tries to add things...HELP..PLEASE!!!
Object reference not set to an instance of an object. (Microsoft.VisualStudio.Platform.WindowManagement)
Program Location:
at Microsoft.VisualStudio.Platform.WindowManagement.DocumentObjectSite.QueryService(Guid& guidService, Guid& riid, IntPtr& ppvObject)
at Microsoft.VisualStudio.Shell.ServiceProvider.GetService(Guid guid, Type serviceType)
at Microsoft.VisualStudio.Shell.ServiceProvider.GetService(Type serviceType)
at Microsoft.VisualStudio.Shell.WindowPane.GetService(Type serviceType)
at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerToolWindow.GetService(Type serviceType)
at Microsoft.VisualStudio.Shell.WindowPane.System.IServiceProvider.GetService(Type serviceType)
at System.ComponentModel.Design.ServiceContainer.GetService(Type serviceType)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.ObjectExplorerControl.GetService(Type serviceType)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.ObjectExplorerControl.System.IServiceProvider.GetService(Type serviceType)
at System.ComponentModel.Design.ServiceContainer.GetService(Type serviceType)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItem.GetService(Type serviceType)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NodeContext.GetService(Type serviceType)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItemBuilder.<GetColumnsFromNavigationService>d__11.MoveNext()
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItemBuilder.AddFields(List`1 list, IEnumerable`1 fields, IDictionary`2 allValidFields, AddFieldsFlags flags)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItemBuilder.GetParentFields(INodeInformation source, Dictionary`2& allValidColumns)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItemBuilder.BuildDynamicItemWithQuery(IList`1 nodes, INodeInformation source, INavigableItem sourceItem, String urnQuery, Boolean registerBuilder, Boolean registerBuiltItems)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItemBuilder.BuildDynamicItem(IList`1 nodes, INodeInformation source, INavigableItem sourceItem, IFilterProvider filter)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItemBuilder.Build(IList`1 nodes, INodeInformation source, INavigableItem sourceItem, IFilterProvider filter)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.NavigableItem.RequestChildren(IGetChildrenRequest request)
at Microsoft.SqlServer.Management.UI.VSIntegration.ObjectExplorer.ExplorerHierarchyNode.BuildChildren(WaitHandle quitEvent)

Hi igorteper,
Any progress?
"MS Visual Studio 2010 Shell (Isolated)-ENU" and "Visual Studio 2010 Prerequisites" had been installed in your computer, or there is no Visual Studio installed on this computer?
You log in SQL Server Management Studio and get an error. For further investigation the issue, please post the error messages in detail.
TechNet Subscriber Support
If you are TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Thanks,
Maggie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. This can be beneficial to other community members reading the thread.

Wlc 5508 get error when use port-channel

We have two wlc in the system 5508 and 4402.
we config HA for 2 wlc, both wlc enable LAG
When I connect 2 interface of 5508 to 2 interface (in a port channel mode on, trunk, dot1q) of a
couple of VSS switch, I cant management 5508 through web any more, and I still can do with 4402.
If I shutdown 1 port int the port-channel, it work well.
Do you know what happen ?
Thanks
Duyen

hi Scott,
We have VSS ( 2 x 6509) trunk with (2 switch 4506). one port of wlc4402 connect to one port of one swith 4506.
2 ports of wlc 5508 conect to 6509, each port connect to one switch 6509.
the config in VSS switch like this:
interface gig1/1/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 500 mode on
interface gig2/1/1
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 500 mode on
etherchannel load-balancer src-dst-ip
( I dont see this command in running config)

I get errors when using tomahawak inputFileUpload component.

Hello everyone. I am a newbie with JSF. I use netbeans 6.1 and apache myfaces and tomahawk libraries. I need to upload a file. I use <t:inputFileUpload /> component of tomahawk but cant put it to work. When i choose the file from the browser and click upload button i get this error on browser.
HTTP Status 500 -
type Exception report
message
description The server encountered an internal error () that prevented it from fulfilling this request.
exception
javax.servlet.ServletException: java.lang.NoClassDefFoundError: Could not initialize class org.apache.myfaces.shared_tomahawk.config.MyfacesConfig
     org.apache.myfaces.webapp.filter.ExtensionsFilter.doFilter(ExtensionsFilter.java:135)
     org.netbeans.modules.web.monitor.server.MonitorFilter.doFilter(MonitorFilter.java:390)
root cause
java.lang.NoClassDefFoundError: Could not initialize class org.apache.myfaces.shared_tomahawk.config.MyfacesConfig
     org.apache.myfaces.renderkit.html.util.AddResourceFactory.getInstance(AddResourceFactory.java:282)
     org.apache.myfaces.webapp.filter.ExtensionsFilter.doFilter(ExtensionsFilter.java:126)
     org.netbeans.modules.web.monitor.server.MonitorFilter.doFilter(MonitorFilter.java:390)
note The full stack trace of the root cause is available in the Apache Tomcat/6.0.16 logs.
Apache Tomcat/6.0.16and my jsp page is below
<%@taglib prefix="c" uri="http://java.sun.com/jsp/jstl/core"%>
<%@page contentType="text/html"%>
<%@page pageEncoding="UTF-8"%>
<%@taglib prefix="f" uri="http://java.sun.com/jsf/core"%>
<%@taglib prefix="h" uri="http://java.sun.com/jsf/html"%>
<%@ taglib uri="http://myfaces.apache.org/tomahawk" prefix="t" %>
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"
   "http://www.w3.org/TR/html4/loose.dtd">
<%--
    This file is an entry point for JavaServer Faces application.
--%>
<f:view>
<html>
    <head>
        <meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
        <title>Endersys License Upload Page</title>
    </head>
    <body>
        <h:form id="uploadForm" enctype="multipart/form-data">
            <t:inputFileUpload id="fileUplod" value="#{upload_backing.file}"
                                storage="file" required="true"/>
            <h:message for="fileUpload" />
            <h:commandButton value="upload" action="#{upload_backing.upload}" />
           <h:outputText value="File Uploaded Succesfully" rendered="#{upload_backing.success}"
                         style="color:green" />
           <h:outputText value="Error: File is not uploaded"
                         rendered="#{upload_backing.success}" style="color:red" />
        </h:form>
    </body>
</html>
</f:view>and this is the content of web.xml
<?xml version="1.0" encoding="UTF-8"?>
<web-app version="2.5" xmlns="http://java.sun.com/xml/ns/javaee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd">
    <context-param>
        <param-name>com.sun.faces.verifyObjects</param-name>
        <param-value>false</param-value>
    </context-param>
    <context-param>
        <param-name>com.sun.faces.validateXml</param-name>
        <param-value>true</param-value>
    </context-param>
    <context-param>
        <param-name>javax.faces.STATE_SAVING_METHOD</param-name>
        <param-value>client</param-value>
    </context-param>
    <servlet>
        <servlet-name>Faces Servlet</servlet-name>
        <servlet-class>javax.faces.webapp.FacesServlet</servlet-class>
        <load-on-startup>1</load-on-startup>
    </servlet>
    <servlet-mapping>
        <servlet-name>Faces Servlet</servlet-name>
        <url-pattern>/faces/*</url-pattern>
    </servlet-mapping>
    <session-config>
        <session-timeout>
            30
        </session-timeout>
    </session-config>
   <filter>
     <filter-name>MyFacesExtensionsFilter</filter-name>
     <filter-class>org.apache.myfaces.webapp.filter.ExtensionsFilter</filter-class>
    <init-param>
        <param-name>maxFileSize</param-name>
        <param-value>10m</param-value>
        <description>Set the size limit for uploaded files.
            Format: 10 - 10 bytes
                    10k - 10 KB
                    10m - 10 MB
                    1g - 1 GB
        </description>
    </init-param>
    <init-param>
        <param-name>uploadRepositoryPath</param-name>
        <param-value>/tmp</param-value>
    </init-param>
    </filter>

<filter-mapping>
    <filter-name>MyFacesExtensionsFilter</filter-name>
    
    <servlet-name>Faces Servlet</servlet-name>
</filter-mapping>

<filter-mapping>
    <filter-name>MyFacesExtensionsFilter</filter-name>
    <url-pattern>/faces/myFacesExtensionResource/*</url-pattern>
</filter-mapping>
    </web-app>and the bean i use is here
* To change this template, choose Tools | Templates
* and open the template in the editor.
package bean.backing;
import java.io.*;
import javax.servlet.http.*;
import org.apache.myfaces.custom.fileupload.UploadedFile;
import javax.faces.context.FacesContext;
* @author brhn
public class main {
    private UploadedFile file;
    boolean success = false;
    public main() {}
    public UploadedFile getFile() {
        return file;
    public void setFile(UploadedFile file) {
        this.file = file;
    public void upload() throws IOException {
            try {
                InputStream stream = file.getInputStream();
                long size = file.getSize();
                byte [] buffer = new byte[(int)size];
                stream.read( buffer, 0, (int)size );
                stream.close();
                success = true;
        } catch (Exception e) {
            success = false;
    public boolean isSuccess () {
        return success;
}i need to make it work. All helps will be appreciated

The logs are by default located in Tomcat/logs and configurable by Tomcat/conf/logging.properties.
Having said that, when I google on [java.lang.NoClassDefFoundError: Could not initialize class org.apache.myfaces.shared_tomahawk.config.MyfacesConfig|http://www.google.com/search?q=java.lang.NoClassDefFoundError%3A+Could+not+initialize+class+org.apache.myfaces.shared_tomahawk.config.MyfacesConfig] then I have the impression that you're using Tomahawk 1.1.7 snapshot and there might be a bug in it. Try using Tomahawk 1.1.6 and see if it works. After all, you may have more luck if you post this issue at their own mailinglist at tomahawk.apache.org.

Call Rejected error when Using CTI Port to call out

Hello,
I am using Cisco Call Recording feature that is enabled on a phone that has a CTI Port and number assigned to invoke a call recording session to dial out a Long Distance number. I used JTAPI tool to invoke a call and then used the CTI that was invoked by the BIB to dial a long distance number. The call leaves the phone and gets to the gateway (MGCP) with 2 T1 Pri's and in the debug I see this error:
KNOW Good call:
001679: *Sep 20 14:39:53.005: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x5069
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA18395
                Preferred, Channel 21
        Facility i = 0x9F8B0100A1080201010201008400
                Protocol Profile = Networking Extensions
                0xA1080201010201008400
                Component = Invoke component
                        Invoke Id = 1
                        Operation = CallingName
                                Name not available
        Calling Party Number i = 0x0080, 'XXXXXXXXX'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0x80, 'XXXXXXXXXX'
                Plan:Unknown, Type:Unknown
001680: *Sep 20 14:39:53.009: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xD069
        Cause i = 0x8081 - Unallocated/unassigned number
001681: *Sep 20 14:39:53.097: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x506A
FAILED Call:
001685: *Sep 20 14:39:56.509: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x1DA8
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98384
                Exclusive, Channel 4
        Calling Party Number i = 0x0183, '2678'
                Plan:ISDN, Type:Unknown
        Called Party Number i = 0x80, 'XXXXXXXXXXX'
                Plan:Unknown, Type:Unknown
001686: *Sep 20 14:39:56.537: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8 callref = 0x9DA8
        Channel ID i = 0xA98384
                Exclusive, Channel 4
001687: *Sep 20 14:39:56.557: ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x9DA8
        Cause i = 0x8295 - Call rejected
001688: *Sep 20 14:39:56.585: ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x1DA8
001689: *Sep 20 14:39:56.593: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x9DA8
001690: *Sep 20 14:40:07.001: ISDN Se0/0/1:23 Q931: RX <- SETUP pd = 8 callref = 0x4200
Anyhelp appreciated.

Hi,
I have looked into the issue. If you are trying to create the BP with general role 000000, i think it might not be possible via LSMW.
The error message is correct, because role 000000 is indeed not relevant for update because if you can see in the customising Tx BUSD, 'FLAG - Do not update' will be active. This is the reason why you are getting the error message of 'No update is defined for the role 000000'.
When you insert a partner in role "000000 General Business Partner",the error message "BP role cannot be updated" will be returned. This error message is very specific for this issue. You can create BP in different roles apart from the general role.
Indeed if you try to change the 'Do not update' flag to inactive state and process the LSMW project you will be able to create the BP but it is strictly not recommended.
This role is a technical role which exists for the creation of BP, and immediately you will fall back to other roles available for the partner.
So i feel you need to change the role before you create BP with this role via LSMW.
I hope this helps.
Regards,
Venkat

Getting error when using the option "Open Shared Calendar"

Hello Everyone,
I have created four calendars for our office all of them for booking meeting rooms.
Three of the four work just fine but the fourth is being a pain.
I'm running Exchange 2010 and all our clients are running Outlook 2007. I have re-created
the meeting room a couple of times just to make sure I hadn't missed anything.
When I, or another staff memeber tries to use the "Open a Shared Calendar"
withing Outlook 2007 in Calendar view, we get the below error.
Cannot display the folder. Microsoft Exchange is not available. Either there are
network problems or the Exchanges computer is down for maintenance.
Any ideas why I'm getting this error?
Thanks,
Sean

Hi Sean,
Could you please check the conference room type,whether it is an Auto Accept or Delegate Type.
checking the conference room type :
Get-CalendarProcessing conference room| fl *policy*
you may get the below results:
>Get-CalendarProcessing conferenceroom name| fl *policy*
RequestOutOfPolicy : {}
AllRequestOutOfPolicy : False
BookInPolicy : {}
AllBookInPolicy : True
RequestInPolicy : {}
AllRequestInPolicy : True
If "AllBookInPolicy : True" it mean it is an Auto Accept type and if "AllBookInPolicy : False" then it is Delegate type conference room.
If it is an Auto accept type then you should have Editor access on the concern room calendar to manage it and the same time if the room is an Delegate type you suppose to have Delegate access over the room.
To check whether you have permissions to access the room calendar.
>Get-MailboxFolderPermission -Identity conferenceroom name:\calendar
RunspaceId : b36c1c40-34df-49de-a978-792c216c211e
FolderName : Calendar
User : Default
AccessRights : {LimitedDetails}
Identity : Default
IsValid : True
RunspaceId : b36c1c40-34df-49de-a978-792c216c211e
FolderName : Calendar
User : Anonymous
AccessRights : {None}
Identity : Anonymous
IsValid : True
RunspaceId : b36c1c40-34df-49de-a978-792c216c211e
FolderName : Calendar
User : skumar(s)
AccessRights : {Editor}
IsValid : True

Getting error when activating serial key with cs6 creative suit specifically for the Flash Builder 4.6

I got he the software Adobe Creative Master Suite CS6
was able to activate all the software except Flash Builder 4.6 keep getting message Serial number is not valid cs6 master collection serial.
Is there anything else needed to be done when activating the program.
Please advise

I have been able to resolve by completing clean/complete uninstall and re-install -- as per these instructions:
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6

Getting error when using iway adapter to access peoplesoft

i am using iway adapters to access peoplesoft but getting the following error:
Error in parsing the input
can anyone tell me what is the format of the input document or xml file that should be sent to the adapter inorder to access peoplesoft?

Hi,
Try searching for:Re: 30EA2 - No Available Databases in Capture step with MS Access Migration
Thread: 30EA2 - No Available Databases in Capture step with MS Access Migration
Posted: Dec 20, 2010 11:04 AM
Also note that copy to oracle - (for just table/column information) is available on right click.
-Turloch
SQLDeveloper team

Getting error when using Pathset class in jdeveloper 11g

i have implemented the code for maintaining the tree state across requests. I'm using Jdeveloper 11g and the problem i'm having is that i cannot use the following import statement : import oracle.adf.view.faces.rich.model.PathSet
The error i'm getting is "import oracle.adf.view.faces.rich.model.PathSet; not used or not found"
i'v tried replacing the above import statement with : "import org.apache.myfaces.trinidad.PathSet" but i get the error "import org.apache.myfaces.trinidad.PathSet" not found
can someone help me plz?
chaj

Hi,
JDeveloper 11 related questions have their own forum
JDeveloper and OC4J 11g Technology Preview
The JDeveloper 11 RichTree does not use PathSet but RowKeySet to keep track of the selected state. A property on the tree component allows you to set the selected state by referencing a RoKeySet e.g. in a managed bean
Frank

Getting error when using PCD 10.5.1 for "simple" migration.

Hey guys,
I'm currently migrating from 9.1.2-X to 10.5.1 and when I look at the VM in the new migration (the 10.X), I see the following error on the console "The hardware you are using is not supported for this product. Installation will now halt".
I made sure I have the right licenses for the host and gave it extra resources because this is the second attempt on this migration.

Hi,
what is the PCD Hardware and UCS Hardware for migrating to 10.5.1 u are using ?
what all licenses u are using?
you can also refer the DOC for more details on PCD system requirement
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/pcdadmin/10_5_2/CUCM_BK_P7081B13_00_pcd-administration-guide-1052/CUCM_BK_P7081B13_00_pcd-administration-guide-1052_chapter_01.html
VMware licenses
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/pcdadmin/10_5_2/CUCM_BK_P7081B13_00_pcd-administration-guide-1052/CUCM_BK_P7081B13_00_pcd-administration-guide-1052_chapter_01.html#CUCM_RF_C1DF129A_00
regds,
aman

Getting Error when using Adaptive RFC in creating model...

Hi All,
When i am creating Model for Adaptive RFC at that time i am not able to login to my R/3 System...
Previously we used to work in ECC5.0 at that time it was working.
Now we are working in ECC 6.0 but error is coming. Name and password not found.
So do i have to reconfigure the NWDS.
If Yes. How to do reconfigure it for ECC 6.0
Pls its very Urgent...........
Regards,
Dhruv Shah

Hi,
JDeveloper 11 related questions have their own forum
JDeveloper and OC4J 11g Technology Preview
The JDeveloper 11 RichTree does not use PathSet but RowKeySet to keep track of the selected state. A property on the tree component allows you to set the selected state by referencing a RoKeySet e.g. in a managed bean
Frank

Getting error when using the "/parameter" switch in command line run

Has anyone experienced this problem before?
My report queries over 100,000 records from a view. When the report is run from the command line every thing works fine.
But when I add a condition using a "parameter", although the report still runs fine from the destop, when launched from the command line it errs.
"Oracle Discoverer Desktop has encountered a problem and needs to close. ..."
"The instruction at "0x0044397c" referenced memory at "0x0000004e". The memory cound not be "read"...."
I'm guessing its a memory issue with my PC. I've tested using a parameter with other reports using fewer records and it doesn't err from the command line.
I can work around the issue by not using a parameter but then I have 20 versions of the same report each with a different condition.
Any suggestions would be appreciated.
Lise McGillis

Hi Michael,
I'm using an DELL Intel Pentium 4 CPU 3.00 GHz with 1 GB of RAM. We use Microsoft Windows XP Prof version 2002.
As for Discoverer we are using 10G, Desktop Client 10.1.2.48.18 - 1047500 KB available memory , 2099744 KB Free disk space.
I'm not sure I have acess to a computer with more RAM but I'm looking into it.
What I'm frustrated by is the fact that the parameter works fine when run directly from the desktop but when passed from the command line it bombs... but only when dealing with mega records.
Lise.

Getting Error When using FCKEDITOR

The server didn't reply with a proper XML file
Check your configuration.
The server didn't send back a proper XML response.
Requested URL:
http://127.0.0.1:8500/CFIDE/scripts/ajax/FCKEditor/editor/filemanager/browser/default/conn ectors/asp/connector.asp?Command=GetFoldersAndFiles&Type=Image&CurrentFolder=%2F
Response text:
<head><title>JRun Servlet
Error</title></head><h1>404
</h1><body>
<pre>
/CFIDE/scripts/ajax/FCKEditor/editor/filemanager/browser/default/connectors/asp/connector. asp</pre><br><pre>
java.io.FileNotFoundException:
/CFIDE/scripts/ajax/FCKEditor/editor/filemanager/browser/default/connectors/asp/connector .asp
at
jrun.servlet.file.FileServlet.service(FileServlet.java:349)
at
jrun.servlet.ServletInvoker.invoke(ServletInvoker.java:106)
at
jrun.servlet.JRunInvokerChain.invokeNext(JRunInvokerChain.java:42)
at
jrun.servlet.JRunRequestDispatcher.invoke(JRunRequestDispatcher.java:284)
at
jrun.servlet.ServletEngineService.dispatch(ServletEngineService.java:543)
at
jrun.servlet.http.WebService.invokeRunnable(WebService.java:172)
at
jrunx.scheduler.ThreadPool$DownstreamMetrics.invokeRunnable(ThreadPool.java:320)
at
jrunx.scheduler.ThreadPool$ThreadThrottle.invokeRunnable(ThreadPool.java:428)
at
jrunx.scheduler.ThreadPool$UpstreamMetrics.invokeRunnable(ThreadPool.java:266)
at jrunx.scheduler.WorkerThread.run(WorkerThread.java:66)
So please anybody guide me for this.I am really surprised why
it going to take asp code?
Thank You,
Jay Pandya
[email protected]
919327335288

Jay,
This happens with the wrong connectors are selected in the fckeditor.js file. Here's a tutorial about installing FCKEditor for a ColdFusion site and how to call and POST data collected in a FCKEditor enabled form.
FCKEditor Installation
Thanks,
Jon C.

Getting error when record type is used

Hi Experts,
Getting error when using record type as in parameter.
PLS-00306: wrong number or types of arguments in call to 'SAL_UPDATE_PROC'
PLS-00302: component 'ENAME' must be declared
PLS-00302: component 'SAL' must be declared
CREATE OR REPLACE PACKAGE emp_details_proc
IS
TYPE emp_record IS RECORD
(empno emp.empno%TYPE,
ename emp.ename%TYPE,
sal emp.sal%TYPE);
TYPE emp_type is TABLE OF emp_record INDEX BY binary_integer;
PROCEDURE EMP_PROC;
PROCEDURE sal_update_PROC
(    p_rule in emp_type
     , p_deptno in number
     , p_job in number
END;
CREATE OR REPLACE PACKAGE BODY emp_details_proc
IS
PROCEDURE EMP_PROC
IS
    V_DEPTNO NUMBER := 10;
    V_JOB VARCHAR2(20):='CLERK';
BEGIN
for rc in (SELECT EMPNO,ENAME,SAL FROM emp where deptno =v_deptno)
         loop
              sal_update_PROC
              ( p_rule => rc
                , p_deptno => V_DEPTNO
                , p_job =>V_JOB
end loop;
EXCEPTION
     WHEN OTHERS THEN
DBMS_output.put_line(SQLERRM);
END;
PROCEDURE sal_update_PROC
(    p_rule in emp_type
     , p_deptno in number
     , p_job in number
IS
    V_ename VARCHAR2(20);
    V_SAL NUMBER;
BEGIN
      V_ename := p_rule.ename;
      V_sal := p_rule.sal;
        IF V_sal <=3000 THEN
        UPDATE EMP SET sal=sal+v_sal*10 WHERE ename=v_ename;
        commit;
      END IF;
dbms_output.put_line(v_ename||'   '||v_sal);
      END;
      END;
Instead of this
SELECT EMPNO,ENAME,SAL FROM emp where deptno =v_deptno;
PROCEDURE sal_update_PROC
(    p_rule in emp_type
     , p_deptno in number
     , p_job in number
If I use
SELECT * FROM emp where deptno =v_deptno
PROCEDURE sal_update_PROC
(    p_rule in emp%ROWTYPE
     , p_deptno in number
     , p_job in number
I am not getting any error.
Please help me.Why I am getting error what is wrong in my code.
Thanks in advance.

for rc in (SELECT EMPNO,ENAME,SAL FROM emp where deptno =v_deptno)
         loop
              sal_update_PROC
              ( p_rule => rc
                , p_deptno => V_DEPTNO
                , p_job =>V_JOB
p_rule => rc       --> What exactly in rc? It's just a counter. You are using this (SELECT EMPNO,ENAME,SAL FROM emp where deptno =v_deptno)query but not using a single value returned from this query in the code.
Ishan

My Application gets Error 37 when using Serial Port VIs.

Similar Messages

Maybe you are looking for