My Ipod classic 160 gb,is dead only blinks when plugged to cpu via usb cable reset apple logo blinks as well Help!!!

My Ipod classic 160gb is dead,It only responds when I plug it in to cpu via usb cable then the screen blinks.When I try to reset it the Apple logo appears but the apple logo  blinks on and off to as long as i hold the buttons down,when i realease the reset buttons it just blinks back and fourth to the blank gray screen,it worked fine yesterday night this morning its tanked.is this unit completely dead or can something be done at home?
Thank you for your help
Ice

I wrote this long time ago, have a read and see whether it can be soloved
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
http://www.ipodresq.com/index.php
http://www.ifixit.com/
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
Spank your iPod
http://www.youtube.com/watch?v=3ljPhrFUaOY
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevant_history/2004/11/meeting_the_sad.html#comment -10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
My iPod ism’t resetting and isn’t being read by my computer
http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

Similar Messages

  • Mouse only works when plugged into a specific USB port

    Hello. I'm using a HP optical mouse that connects via USB plugin.
    HP PIN: 505062-001 Rev.A
    Operating System: Windows 7 Home Premium SP1
    It only has full functionality when plugged into a specific USB port on my desktop. I can't get it to work with any other ports or chained with a HUB plugged into the port it likes. All of my other USB devices work fine with those ports and my HUBs. The red light on the bottom lights up but the mouse pointer does not respond to movement and clicking the buttons does nothing either.
    1) I'm confident, that it's not a problem with the desktop hardware
    2) I'm confident, that it's not a problem with the mouse hardware
    When the mouse is fully functional, it's displayed under Devices and Printers, in the Devices category as "USB OPTICAL MOUSE".
    When connected with the other ports or through a HUB, it appears as TWO entries in the Devices category:  "HID-compliant mouse" and - here's the suspicious part - "HID-compliant keyboard"
    I suspect that something's up with the driver for the mouse. Any clues, as to which driver I need? Or, is the cause of the problem something else entirely?

    Hello Tick_Noby,
    Your mouse only works in certain usb ports.
    Has the mouse ever worked in the ports?
    You can go to device manager and uninstall the fake keyboard and the mouse and restart the computer.
    It seems that the driver is not correct for the mouse.
    Also reset BIOS defaults.
    Turn off the computer.
    As you turn it back on tap the F10 key. This will load BIOS setup utility.
    Press F9 to load defaults.
    Press F10 to save and exit.
    When the computer boots back up, check to see if everything is working.
    If it has not been to long since the problem started, you can run a system restore.
    This will take the system back to when everything was working correctly without affecting your personal files.
    Here is a link on how to do a restore.
    Let me know how everything goes
    Have a good day.

  • TS1538 ipod classic 160 gb. unable to restore or format. tried all the recommended steps. no go. Any suggestions?

    ipod classic 160 gb. Unable to Restore.  Also cannot format via C:\ right click on drive and Format.  Have tried all the recommended steps I can find. No luck. Any suggestions?

    do you need an internet connection to do a restore? (after downloading the software of course)
    I can't get to a different connection until Friday night...
    It doesn't seem like the antivirus and whatnot made any difference.
    what kind of hardware problem do you think it is/would it be fixable or would I have to buy a whole new ipod?
    I think the harddrive is still okay... it feels the same vibration wise now as it was when it was working fine- no awkward clicking or movements like I experienced when my old laptop's harddrive crashed.

  • Ipod Classic 160 6th g. doesn't sync w/Imac g5 non intel OS 10.4.11. This is a replacement for same ipod which was stolen recently. That pod worked fine with Itunes 9! Now this pod says it only works with Itunes 10.7. ***!!!! Why has Apple screwed up?

    My ipod classic 160 6th gen. was recently stolen. It had 3000 tunes on it and it synced perfectly with Itunes 9 on my Imac G5 non intel OS 10.4.11. So I recently bought same model and guess what, it doesn't sync at all. Now message says it only works with Itunes 10.7 and up. I certainly cant afford to buy a new intel based Mac and I really dont need a new pc. It feels like Apple has dropped the ball on its long time users and tough luck to you and all the $$$$$$$ spent on downloading songs and buying ipods over the years! I AM SO ANGRY THAT I CANNOT BRING MY MUSIC WITH ME ANYMORE. I dont know if there is any solution to this except being extorted to upgrade to new tech! I have been trying to get answers to this issue but nothing seems to work. Any help would be greatly appreciated. I am not a tech genius so extremely techy solutions will be in vane.

    one more detail, after a restore, when I attempt to reload music to the ipod, if I try and move, say, 20 files, the transfer seems to work as it should but then stalls on the last file.  Eventually, the status will change to "Updates Files on (my ipod)" a and suggests the iPod is syncing  even though I have the auto sync feature turned off.
    This process eventually works itself out, and seems to take longer relative to the number of files I attempt to transfer.   Once done, howver, if I try and eject and dismount the iPod, iTunes stalls with the spinning pinwheel and I am warned that the iPod is syncing again with the spinning candy cane status bar.     Eventually thisd works itself out and the iPod dismounts from iTunes and the desktop and eventually the iPod is free to disconnect.
    Then if I try and play the music I just transfered, the iPod says there is no music loaded.
    Ideas?

  • Ipod classic 160 gigs, only 150 gigs free when arrived?

    so my empty, new ipod classic 160
    reads only 150 gigs free
    now i know hard drives lose a few gigs in the translation
    from retail packaging number, to actually available gigs
    but 10 gigs?
    what gives?

    Hi Dr. Rek,
    Actually, losing 11 GB with the 160 GB iPod Classic makes sense.
    It's the same binary system and same percentage lost (about 8%, I believe) as all of the previous iPods were. It just seems worse when several GBs are lost in the conversion, simply due to the fact that this is a bigger hard drive we're dealing with.
    Think of the 27.72 GB vs/ 30 GB discrepancy, for example; 92.4% (total storage space gain) is the same rate of as it's always been, just with a 160 GB model, it turns out as about 11 GB lost.
    So, it's normal for your computer (and on your iPod, too) to read the GB space as about 149 GB instead of 160; if you calculate it, it's actually the same percentage, but not a similar amount that we might be used to, since the iPod's hard drives are just getting larger in storage space.
    I hope that all makes sense!
    -Kylene

  • My iPod Classic 160 is in disc mode and won't turn off, itunes doesn't recognize it - ¿how can I make it work again?

    My iPod Classic 160 is in disc mode.  I responds to nothing.  iTunes doesn't recognize it.  It doesn't sync.  I've tried to restore and got error 1429.  Now it just stays in disc mode and won't turn off.  I'm keeping it connected to the charger so it doesn't go dead.  Is there anything I can do to resurrect my pod?

    To get out of disk mode do a iPod Hard Reset.
    Toggle the Hold switch till you dont see the red mark.
    Press Menu and Center buttons simultaneously for about 10 secs till the Apple logo comes ON then release the buttons
    Select your preferred language.
    See this Apple support Article on the 5Rs.
    http://www.apple.com/support/ipod/five_rs/classic/
    If you try to restore and get a1429 error message, read this Apple Support Article
    http://support.apple.com/kb/TS1372
    Good Luck!

  • My Ipod Classic 160 GB will charge but is not recognized on my macbook or in itunes. Just began suddenly

    I purchased my Ipod Classic 160 GB about a year ago new and never had any issues until lately. I recently updated my itunes to the newest version and my Ipod seemed fine and didn't have any trouble. About a week later my Ipod was no longer recognized by Itunes or my Mac book. The catch is, that my Ipod is still able to charge but never shows any signs of connection besides the charging screen. I have no clue where to begin.
    Any help would be awesome! Thanks

    Have you updated your iPod and iTunes sofware?
    most cases, iTunes can play these high quality songs, which is meant for newer mobile devices like  iPhones, iPod Touch, nano and iPad, which the older iPod cant play, but only playable with iPod classic sofware version 2.0.4
    most likely it is an incompatible song format, read this Apple support article.
    http://support.apple.com/kb/HT1334?viewlocale=en_USet
    If  your iPod software is version 1.1.2, then you have to use lower quality format.
    Can you select the problematic song, and Advance -> create iPod version

  • IPod Classic 160 GB doesn't work for audiobooks in BMW X3 F25

    Hello
    I have been owning a 160 GB iPod classic for a while now. I have newly acquired a BMW X3 (2012 Model, F25). The problem is that when listening to audiobooks, the iPod doubles or triples the speed (and pitch) when I return to the car after having parked. So it runs fine at first, then I stop and park the car and return and then it sounds like Donald Duck is reading to me ;-)
    The car comes with the USB interface to which once can connect media players like the iPod. I am using the original BMW "Y-shape" cable that has once connection on the iPod that then splits into an USB and a 3.5mm jack. I also tried cables from Belkin and the cable that came with the iPod, but all to no avail.
    It is not the Audiobook faster/slower function of the ipod that is activated because that would not change pitch, it's like "the record is turning too fast", you can see the seconds in the car's display movig much faster than at a second's pace. The iPod subsequently retains this increased speed even if not connected to the car anymore and can only be slowed down again by resetting it.
    I onw an older iPod photo 80 GB which does not exhibit this behavior.
    The iPod classic 160 is at the latest software level and so is the car.
    Any ideas?
    Regards
    Chris

    Having the same issue.  See https://discussions.apple.com/message/23993137#23993137.

  • New iPod Classic 160 GB not read by MacBook

    My new iPod Classic 160 GB is not read by my MacBook.  It doesn't show up in Finder or in iTunes.  What can I do so my computer recognizes it?

    Swap to another USB 2.0 port and dont use any USB HUB. (only one of the Macbook USB port can be use for iPod Classic)
    If that doesn't work, use another  USB cable.
    When you connect to the Macbook USB port, the iPod screen should show this symbol.
    Battery charging (lightning bolt
    or
    If you get just the menu screen, it means there is no signal or power coming across the cable from the Macbook to the iPod.

  • Ipod classic 160 not visible in tunes 12

    My perfectly functioning ipod classic 160 gb is invisible to itunes. It shows on the ipod screen it is connected and it shows on the imac screen as an ipod. In itunes it does not exist. It worked perfectly with itunes before the upgrade. I have seen the device bar and my iphone 5s displays there normally and functions perfectly. When only the ipod is plugged in, there are no devices in the bar and the itunes menu for device is greyed out.

    If you have not, disconnect all USB devices (including any hubs).  You can leave standard keyboard/mouse connected, if used.  With iTunes running, connect iPod to a direct USB port by itself.  This is to rule out a problem a conflict between connected USB devices, or a lack of power on the USB bus for all connected USB devices.  If you already tried that, or it does not help...
    Since the iPod appears initially in iTunes, the problem may be a "feature" that recent Windows PCs, with Windows 8 and USB 3.0 ports, seem to have.  It is an "energy saver" setting that turns off full power to the USB port if the connected device is deemed "inactive" by Windows.  When you connect the iPod, iTunes does its initial sync for a few seconds.  That's when the iPod is seen in iTunes.  After the sync, iTunes unmounts the iPod's disk.  If Windows considers the iPod to be inactive and turns off full power to the USB port, that is when the iPod disappears from iTunes.
    If this is the cause, you may be able to go into Windows Control Panels and turn OFF this feature (so USB ports always stay at full power).  If that does not work, or you can't find such as setting...
    Alternately, you can Enable disk use on the iPod.  With disk use enabled, the iPod's disk remains mounted by the system until you Eject the iPod in iTunes, so the port remains at full power.  This may be difficult, if you don't have enough time to click on the iPod in iTunes and check the box for Enable disk use on the iPod Summary settings screen (and click Apply).  I'm assuming you have your iPod set to automatically sync your entire iTunes music library.  If so, you can extend the iPod's initial sync (when you connect it) by making a significant change to your iTunes music library (before you connect it).  If you happen to have some music CDs that you need to import into iTunes, that would work.  Add new songs to your iTunes library, and then connect iPod.  If you use the Sync only checked items setting, you can uncheck a large number of songs in your music library, connect to sync, then recheck the songs, connect to sync.  Making iTunes sync a few dozen songs during the initial sync should give you enough time to go to the iPod's Summary settings screen, and check the box for Enable disk use (and click Apply).
    If that does not work (or the iPod still disappears quickly even when there are changes to sync), the cause something else.  FYI - It's not because iTunes 12 does not support discontinued iPods.  I have an 3rd gen "classic" iPod from 2003, and it works fine with iTunes 12.

  • How do I get to buy nwe games for my iPod Classic 160 GB?

    Hi! My name is Valentin.
    I bought an iPod Classic 160 GB, last month. I mean in november 2013.
    It only has 3 games on it. I would like to buy some new games for it & I don't know how. I mean I don't know how to look for games that are made only for this iPod... Because, until now I only found games made for iPhone & iPad...
    Can anybody help me with this?
    Please!
    Thanks a lot...
    Bye!
    <Email Edited by Host>

    You cannot buy games for the iPod Classic.

  • Ipod classic 160 using 30GB laptop

    Is there a way to import my extensive cd collection (at least 160GB worth) to my ipod classic 160 using a laptop that has only 30GB? Can I somehow use my 1TB external drive to help get all the music onto my ipod? So far everything I import to itunes goes directly on my laptop which has been quickly overloaded. Can anyone give me an idea of what to do here. This was so easy using non apple mp3. There must be a way!

    First, there is no need to convert mp3 files to AAC, iTunes and iPod support mp3 just fine. So, you can rip your CDs in iTunes in the mp3 or AAC format, or any of the formats supported by iTunes.
    Second, it sounds like you’re interested in moving your library off of your laptop and onto your external drive, no problem! That makes it easier to help if that is your ultimate goal. But just to make it clear, there are a few considerations you need to be aware of:
    a- iTunes has a “Consolidate Library” utility that lets you port all your music files to a new location. Doing this leaves the original music files in place and creates copies in the new location. So, you need to decide if you want to keep the originals or delete them once they are all copied to the external drive. You can make that choice later.
    b- When you consolidate your library to your external drive, iTunes will have to manage the organization of the files and folders. So, if you’re using your own way of filing your mp3 files and not letting iTunes manage it, then consolidating your library will copy all your files into the iTunes organization on the external drive (but your original files will remain where they were).
    c- Having an iTunes library on an external drive works just fine but there can be a few quirks. If you have a PC, sometimes Windows decides to change the drive letter of your external drive for no apparent reason. Also, if you start iTunes and it can’t find the external drive (disconnected, power off, new drive letter, etc.) then iTunes will open with a default library, which it expects to be on the C:\...\My Music\iTunes location. If you don’t have a library file in that location, then iTunes will create one and open up with a blank library. However, both of these risks can be handled easily and are recoverable.
    d- You can have multiple iTunes libraries, such as the one on your external drive and perhaps the original library on your laptop. However, all libraries are independent so when you change one there is no change to the others. If you manage multiple libraries, you need to decide up front which will be your primary library. Since you have a capacity limitation on your laptop, your primary would be the external drive. The reason to decide this is so that (1) if you auto-sync your iPod, you want it to reflect what’s in the primary library, which may be different from the one on your laptop, and (2) when you add new music, make tag changes, make new playlists, etc., you make sure you’re doing that to your primary library so that the changes get put onto your iPod. So, if you decide to keep the original library on your laptop as an auxiliary library, then you should not auto-sync your iPod with that library open since over time it will differ from your primary library on your external drive. Also, when adding new music, do that with your primary library open, not the one kept on your laptop. With some experience, you can learn how to add new music to your external drive, then also add it to your laptop, but I won’t get into that now.
    So, if you’re ready to go through with this, follow these steps:
    1- Make a backup copy of your "iTunes Library.itl" file. By default, this is located in your C:\...\My Music\iTunes. Keep a copy of this file in a safe place just in case something goes wrong with the consolidation (see step 9 for recovery). You should make a habit of backing this file up anyway since it contains all your playlists, song ratings, and play history.
    2- Create a folder on your external drive where you’re going to put your music files. If you have some music already on the external, I don’t recommend putting your new library there, create a separate folder (e.g. E:\iTunes Music). If you already have some music on the external drive that you want in iTunes, you will add those at the end of this process.
    3- Start iTunes and go to your iTunes preferences (Edit/Preferences, then click on the Advanced tab). Next to the “iTunes Music folder location” window, click on the “Change” button and navigate to the folder you created in step 2. iTunes will put up a message indicating something like “updating library” but that doesn’t actually move your library.
    4- While still looking at your iTunes preferences, make sure these two options are selected: "Keep iTunes music folder organized" and "Copy files to iTunes music folder when adding to library". Close the preferences dialog.
    5- Select the iTunes command Advanced/Consolidate Library. iTunes will warn you that this is a big change, so let it rip if you're ready. iTunes will copy all your laptop’s library to the new location on your external drive. This may take awhile if you have a large library.
    6- When the consolidation is complete, right-click on any song and select Get Info. Check to see that iTunes has the native file stored in the new location on the external drive.
    7- This step is optional, but I recommend doing it to help prevent problems with drive letter changes, and it makes your iTunes library completely portable to other Windows PCs running the same version of iTunes as your laptop. Close iTunes and go to the C:\...\My Music\iTunes folder. Move (don’t copy) the "iTunes Library.itl" and "iTunes Music Library.xml" files to your external drive. You can put them anywhere but I recommend a folder that is easy to see and understand (e.g. E:\iTunes Library Files). Now, hold the Shift key while you start iTunes – keep holding the Shift key until you are prompted to “Choose Library” or “Create Library”. Select “Choose Library” and navigate to you put the "iTunes Library.itl" file on the external drive. iTunes will start up as usual. Note that holding the Shift key while you start iTunes is how you toggle between libraries, and how you can create a new (blank) library. Also, iTunes remembers the location of the last library it opened, so you don’t need to use the Shift key to re-open the library you last used.
    8- If you had music on the external drive that you want to add to iTunes (now that you have extra capacity on the external drive), then simply drag and drop these files directly into your iTunes library. iTunes will make copies of these songs and organize them in the new folder structure you’ve set up – you can delete the original copies of these songs once you confirm that they’re new location in iTunes is set.
    9- If any of the above steps got messed up, or you’re not happy with the results, then simply restore the copy of the "iTunes Library.itl" file you backed up in step 1 (put it back in the same location), then hold the Shift key while you start iTunes and navigate to the original "iTunes Library.itl" file location on your C: drive.
    10- If all is well and you don’t want the original files on your laptop, then delete away. If you decide to keep the original files as an alternate library, then do the same as in step 9 to restore the original library. You can then toggle between libraries by holding the Shift key while starting iTunes and selecting the appropriate "iTunes Library.itl" file. Note that to change from one library to another, you need to close iTunes and restart it with the Shift key being held – you cannot change from one library to another with iTunes open. Also, sometimes it helps to put something in each library so that you can easily tell which one you have open. Maybe create a folder in the iTunes source column called "Primary" or "Secondary" so you can tell when you open one library vs. the other.
    11- If you launch iTunes expecting it to open the library on your external drive and it comes up with an empty library, or the original library, that may mean that your external drive is not being recognized by your laptop. Check to make sure it is active, then re-start iTunes with the Shift key and select the "iTunes Library.itl" file on the external drive to return to your primary library.
    12- If you have other PCs with the same version of iTunes, you can connect your external drive to them and use the Shift key as you launch iTunes to select your library. This makes your library portable to other computers – cool huh?

  • How can i enjoy Z+ music on ipod classic 160 GB.

    Hello guys, i am using ipod classic 160 GB and i have a query regarding listening of Z+ music on ipod classic. Does anybody know about this, how to do this.

    iPod Classic only supports Music (and videos and photos), but not apps. If you want to listen to Hans Zimmer music on the iPod Classic, buy the music if you don't own it already and sync the iPod through iTunes.

  • Is there a bluetooth adaptor for an old iPod classic (160 GB) that also works like a radio remote?

    Is there a bluetooth adapter for an old iPod classic (160 GB) that also works like a radio remote?  I have a bluetooth headset and I want to listen to FM radio on my iPod.
    Or is there a better way than to use an adapter in order to listen to  the radio on an iPod with a bluetooth headset?
    TIA!

    Have you updated your iPod and iTunes sofware?
    most cases, iTunes can play these high quality songs, which is meant for newer mobile devices like  iPhones, iPod Touch, nano and iPad, which the older iPod cant play, but only playable with iPod classic sofware version 2.0.4
    most likely it is an incompatible song format, read this Apple support article.
    http://support.apple.com/kb/HT1334?viewlocale=en_USet
    If  your iPod software is version 1.1.2, then you have to use lower quality format.
    Can you select the problematic song, and Advance -> create iPod version

  • "This game cannot be launched error" iPod Classic 160 Gb

    I have an iPod Classic, 160 Gb. I purchased Sudoku from the iTunes store.
    The game downloaded to my computer; and it shows in the iPod Games tab.
    It appears to sync to the iPod, but in the iPod's games menu there is no icon for the game (just the black and white dice). When I try to play the game, I get the "This game cannot be launched error" with the prompt to reinstall the game.
    Are there any fixes for this? I've tried all the troubleshooting in the support docs, and nothing seems to work.

    Thanks for your suggestions; however none of them worked.
    I contacted technical support, and the only suggestion they had for me was to request a refund - because for some reason, unknown to them, the game doesn't work on my iPod.
    I'm not generally a ranter - I try to be polite to people, in person, on the phone, online - wherever, but I have to say that in my experience, Apple seems to have the worst support of any company with which I have ever dealt.
    After being told no less than eight times, by five different representatives from iTunes support, I was referred to technical support, who told me in essence, "tough cookies" (although the representative certainly didn't say that, he was quite polite).
    I had to double check that I was talking to "technical" support.
    I've been a faithful iPod user for many years; but this experience has certainly soured me. I will have to think long and hard before buying another Apple product if the support I have experienced is indicative of a typical support instance.
    Thanks again for your suggestions.

Maybe you are looking for