My ipod nano 6th gen keeps stopping in the middle of a song, My ipod nano 6th gen keeps stopping in the middle of a song

My ipod nano 6th gen keeps stopping in the middle of a song

Double check to make sure the headphones are plugged ALL the way in meaning the white part of the headphones is flush with the Nano and no silver from the plug can still be seen.
The new headphone jacks are a bit tigher than previous generations and require a little bit of extra force to get the headphones to fully connect.
B-rock

Similar Messages

  • Ipod nano 6th gen askinh for resore every time i connect and after the restore not showing the sysnced song on ipod

    i have a ipod nano 6th gen, few days back when i tried to add few songs through iTunes it gave me error that it "can't connect to ipod . restore it" so i did and after that i synced al the songs and it showed that my my empty ipod has been up few GB's. after i disconnected , i could not see any song on the ipod . when it connected back the ipod the got same error about restore. i dont know what to do now , please help.

    Hello Singhindia,
    It sounds like you restored your iPod Nano when iTunes prompted you and it appears to sync. When you disconnect it and look at the content, the songs arent there, and when you plug it back into iTunes you get the same message again. I would recommend these troubleshooting sections from the following article to help isolate the issue to hardware or software:
    iPod nano: Error message saying that iPod 'could not be identified properly'
    http://support.apple.com/kb/TS3218
    Verify that iTunes is installed and updated
    Restart the computer
    Verify that Apple Mobile Device Support is installed
    Verify the device's USB connection
    Verify that the Apple Mobile Device Service and iPod service are both running
    Verify that the Apple Mobile Device Driver is installed
    Remove and reinstall iTunes
    If the issue continues, gathering iPod Diagnostics may be helpful for you or for support personnel in identifying the issue.
    Additional Information
    Certain phone connectivity software from vendors such as Samsung, Nokia, Bora, Novatel, and Sony may also cause this issue. If you have such software on your computer:
    Uninstall your Samsung, Nokia, Bora, Novatel, or Sony phone connectivity software and test. Contact the manufacturer of this software for assistance in doing this.
    Remove iTunes and all related Apple software by following this article (for Windows XP), or this article (for Windows Vista and Windows 7).
    After reinstalling iTunes, test the iPod nano.
    If you still need your phone connectivity software that was removed, reinstall this software and test your iPod nano to ensure it still functions with iTunes. Contact the vendor of your phone connectivity software if the issue returns.
    While the error message is different than you are seeing, the troubleshooting is relevant for you.
    Thank you for using Apple Support Communities.
    All the best,
    Sterling

  • Hey, the stand-by button on my iPod nano 6th gen has been randomly stuck/pushed into the ipod were it does no longer work. How do i fix it?

    Hey, the stand-by button on my iPod nano 6th generation has been pushed into the iPod, I guess after being pressed a lot, to the point were it doesn't work, what do I do to fix this???

    You'll need to take or send the iPod in for service or repair either via Apple or a third party company that does repair work on iPods.
    B-rock

  • TS3474 How do I get the radio to work on my iPod nano 6th gen?

    I have synched my Nano & have music...I have plugged in the earphones, but nothing happens with the radio. I've read the support article about the FM radio, but I don't have any of the radio controls shown in the article--all I have is the radio icon and the Now Playing icon, and when I tap the Now Playing icon, it shows what music is playing, not radio controls. Help!

    As mentioned above, the reason is that the FM radio uses the headphone cable as an aerial, so the phone insists on it being connected. It's the same with other Nokias. Apparently there are complicated technical reasons why the FM radio can't use the same antenna as the phone signal.

  • Itunes says that the version of software on my ipod touch 3rd gen is up to date, but IOS 5 is avaliable. I have checked for software updates for days but it keeps saying that 4.2.1 is the current version. Why cant i get IOS 5?

    itunes says that the version of software on my ipod touch 3rd gen is up to date, but IOS 5 is avaliable. I have checked for software updates for days but it keeps saying that 4.2.1 is the current version. Why cant i get IOS 5?

    bradenfromwaikerie wrote:
    itunes says that the version of software on my ipod touch 3rd gen is up to date, but IOS 5 is avaliable. I have checked for software updates for days but it keeps saying that 4.2.1 is the current version. Why cant i get IOS 5?
    because you do not have a 3rd generation device. The OS Version says so , otherwise you would be at 4.3.5 minimum and also Itunes is also always correct in determining if you have the latest OS ( if not it fetches the newest from Apple's Servers ) . And because a 2nd generation iPod stops at 4.2.1 you can't get the newest OS, because your device is old. Buy a new iPod , they have iOS5 preinstalled.

  • I have an iphone 5s and it is synced to itunes and works fine. previously I have downloaded audiobooks to my wifes 6th gen nano using this account - now I tunes does not recognize the device and also it seems that it is not being read by the computer?

    I have an iphone 5s and it is synced to itunes and works fine. previously I have downloaded audiobooks to my wifes 6th gen nano using this account - now I tunes does not recognize the device and also it seems that it is not being read by the computer?

    Hey Stan1958,
    Thanks for the question. I understand you are experiencing issues with your iPod nano and iTunes. Based on your symptoms, you may find the following resources helpful in resolving this issue:
    Windows
    iPod appears in Windows but not in iTunes
    iPod not recognized in 'My Computer' and in iTunes for Windows
    iTunes reports that "iTunes cannot recognize this iPod at this time"
    Thanks,
    Matt M.

  • I have a ipod nano 4G, and to sync my music, i have to put my ipod in disk mode. but when i try to turn it on regularly, it gets stuck on the apple logo screen. any idea how to keep it from getting stuck?

    i have a ipod nano 4G, and to sync my music, i have to put my ipod in disk mode. but when i try to turn it on regularly, it gets stuck on the apple logo screen. any idea how to keep it from getting stuck?

    Did you also check under Albums?  All Songs?
    iPod Nano 5th Gen. User Manual

  • Ipod nano 6 gen hangs when turning off the backlight. That is, it doesn't respond to button presses on the touch screen.

    ipod nano 6 gen hangs when turning off the backlight. That is, it does not respond to button presses on the touch screen. He also has just a white screen instead of the desktop display. Tried to rearrange the screen from another Ipod nano, but nothing came of it - all the same ... What should I do?

    Hi Rc_Drifter,
    Welcome to the Support Communities!  The article below will help you troubleshoot the issue you are having with your iPod nano. Restoring the device may resolve the backlight issue as well.  
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/ts3474
    Display shows a white screen
    Try putting the iPod into disk mode:
    Reset the device (press the Sleep and Volume Down buttons simultaneously until the display turns black—about eight seconds).
    When the display turns black, hold down the Volume Down and Volume Up buttons simultaneously until the device enters Disk mode.
    While the device is in disk mode, sync it to iTunes and try to restore.
    I hope this information helps ....
    - Judy

  • Ipod nano 6 gen power button and volume up and down not working, Ipod nano 6 gen power button and volume up and down not working

    Ipod nano 6 gen power button and volume up and down not working, Ipod nano 6 gen power button and volume up and down not working

    Try restarting your device. If that doesn't work, take it to an Apple store. If it is less than a year old and just stopped working, they will replace it for free (be sure to back it up to iTunes first). If you dropped it, you will have to pay because Apple will not replace a device due to "Human Error." If it is more than a year old, you will either have to pay to get it fixed, or have to pay to get it replaced.

  • How can I remove the old apple id from my ipod 4rth gen to log in my new apple id ? (my old apple id keeps showing automatic I can't put my prefer new apple id)

    How can I remove the old apple id from my ipod 4rth gen to log in my new apple id ? (my old apple id keeps showing automatic I can't put my prefer new apple id)

    - Note that apps are locked to the account that purchased them.
    - To update apps you have to sign into the account that purchased the apps. If you have apps that need updating purchased from more than one account you have to update them one at a time until the remaining apps were purchased from one account.

  • Hey. I've got a 3rd gen nano that I've just bought, used. When I plug it into mt PC, (win7) and open I tunes, I can't sync my library and under 'devices' in the 'file' colume it acknowledges this ipod but only to transfer purchaces. sync not available

    I've got a 3rd gen ipod nano that i've just bought 'used'. When i plug it in to my PC, (win7) I can't sync my i tunes library and under 'devices' in the 'file' column it acknowledges this ipod, but sync and backup are not available. Only have  'transfer purchaces from....' which does nothing for me. any help would be greatly appreciated

    Sorted it out. If anyone has this problem i reccommend visiting http://forums.ilounge.com/ipod-classic-ipod-5g-video/237546-ipod-classic-80gb-fr eezes-itunes-need-restore-plz-help-2.html#post1403546 there's some pretty good advice on it. have to go into control panel and re-format iPod into NTFS file. good luck.

  • I have a pc running vista and the hard drive crashed how can i transfer my songs from Ipod nano 5th gen to my new hard drive and into itunes

    I have a pc running vista and the hard drive crashed how can i transfer my songs from Ipod nano 5th gen to my new hard drive and into itunes

    Right click on your device in the device list and choose "transfer purchses" to copy all music bought in iTunes to your new iTunes library.
    For all other media you'll have to use 3rd party software, examples are mentioned in this thread:
    http://discussions.apple.com/thread.jspa?threadID=2013615&tstart=0

  • What can i do to sort my ipod touch 4th gen, when ever i connect it to my laptop my itunes keeps saying, and i quote "itunes could not connect to this ipod, an unknown error has occured" please helpppppp i have not had my ipod for long either

    what can i do to sort my ipod touch 4th gen, when ever i connect it to my laptop my itunes keeps saying, and i quote "itunes could not connect to this ipod, an unknown error has occured" please helpppppp i have not had my ipod for long either

    - Try restoring on another computer.
    -  Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • Sometimes when listening to music or a podcast, it will stop and start in rapid fire.  I have a 4th gen iPod Touch.

    Sometimes when listening to music or a podcast, it will stop and start in rapid fire.  I have a 4th gen iPod Touch.  A Genius suggested something went wrong during the transfer from my MBP to my iPod, but I tried resyncing it, and it seems to happen haphazardly.  Even if a podcast plays oddly one time, it might play perfect the next - so it can't have been the sync that went bad. 

    - First try a reset. Nothing will be lost.
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    - Next restore from backup
    - The restore to factory defaults/new iPod

  • I upgraded to itunes 10.6 and I can't manually sunc to my ipod nano 5th gen anymore. I have re-installed itunes, restored my ipod and tried it dozens of times

    I upgraded to itunes 10.6 and with that "upgrade" I can't manually sunc to my ipod nano 5th gen anymore. I have re-installed itunes, restored my ipod, tried syncing under another users account and everything else I can think of. It syncs ok upon initial start-up but then when I tryp to select podcasts or music to sync to it, itunes crashes. Now that I restored my ipod, I can't even get my old podcasts much less add new ones.

    Do you have any better luck with that if you update to iTunes 10.6.1.7?
    From the notes for the release:
    iTunes 10.6.1 provides a number of improvements, including:
    • Fixes several issues that may cause iTunes to unexpectedly quit while playing videos, changing artwork size in Grid view and syncing photos to devices.
    • Addresses an issue where some iTunes interface elements are incorrectly described by VoiceOver and WindowEyes.
    • Fixes a problem where iTunes may become unresponsive while syncing iPod nano or iPod shuffle.
    • Resolves an ordering problem while browsing TV episodes in your iTunes library on Apple TV.
    http://www.apple.com/itunes/download/

  • What is the screen lock default code for iPod nano 5th gen?

    What is the screen lock default code for iPod nano 5th gen?

    There isn't one.  You'll need to connect the Nano to your iTunes library and restore to factory settings.  There is no other way.
    B-rock

Maybe you are looking for

  • How do I use the Scanner class to read in sentence as 1 string?

    From my code: Scanner scan=new Scanner(System.in); String message=""; System.out.println("Enter message: ");//get message to transmit message=scan.next(); System.out.println("Message: " + message + " will be used for the simulation");I would like to

  • MSDOS command window

    I know that this doesnt apply to LabVIEW, but there isn't an 'Off topic' board on the forums to post under, and you guys know more about computers than anyone else I know so I decided to ask this question here. I have windows vista (if it matters for

  • Wifi devices showing my SSID 3 times.

    Hello.  First off, let me say I am new here and have only some experience setting up wifi, etc.  I apologize in advance if this question has been asked before or is something simple I've overlooked.  Wireless devices are showing 3 SSIDs.  I am using

  • My display color shifts to a blue tint when opening photoshop and bridge with Yosemite

    The display on my mac book pro color shifts to a blue tint when opening Photoshop CS6.  Any suggestions on how to maintain the current color profile?  My photography work is dependent on proper display calibration.  Thank you

  • I cannot view photos on my ipod after syncing from imac 10.9.5

    I have a 5th generation ipod, 80gb. I have synced to my late 2012 imac 10.9.5 and am unable to see photos. It says cannot sync as file can't be found. My music has all synced but I just see blank squares for photos, is this an incompatibility issue?