My jetpack won't charge. I only use the cable that came with it. and by won't charge, I mean even when plugged in the battery keeps dropping and never goes up.
My MiFi jetpack 6620 doesn't charge. I've plugged it into the charger that comes with it, and only that charger. But nothing happens. The battery keeps getting drained. I first attempted when it was at 16%. After being on the charger a few hours, it dropped to 15%, then 14%. I'm currently at 12%. I've tried different outlets at different locations. And I've tested the charger cable on my phone and it charges that just fine. Which is more likely: the battery is defective or there is a problem with the jetpack itself? and the real kicker is that I've only had it for a week.
Happy Friday cjyoyomasta! I wanted to reach out to you to see if you received the assistance that you need with your jetpack. May I ask have you took the device to the store for assistance? If so, what was the results? If you can provie us with a status update then we can assist, if still needed.
Thank you…
ArnettH_VZW
Follow us on Twitter @VZWSupport
Similar Messages
-
Macbook does not recognize iphone 5s when connected using usb cable that came with charger
I have a mac book pro Retina, 15-inch, Late 2013 and iPhone 5s. When I connect iphone to the macbook using the usb cable that came with iphone charger, macbook pro is not recognizing the iphone 5s.
Does any one have any solution for the problemiOS: Device not recognized in iTunes for Mac OS X
BTW, this is the Mac Pro desktop forum -
Have a brand new iPhone 5S and Nano iPod. 5 days old. Using original charging cord and getting message from both units that the cord is unsupported. Is the cord damaged somehow? It looks fine . Today I was trying to SYNC Nano with laptop to transfer MP 3.
Hi Gerardo,
You are going to have to take your device and charger cord to an Apple Store. We have no way to diagnose why it is not recognizing it as an authentic Apple charger. If it is defective, they will replace it free of charge, since you are still well under warranty.
Cheers,
GB -
Ipod touch 5th gen says not able to charge when imusing the cable that came with it
My Ipod touch 5th gen says charging is not supported with this accessory when the cord im using is a cable that came with it and the cable is less the 5 days old. i also know the usb slot works for powering the ipod because it was before. i have treid useing different ports on more than one computer but with no luck. any help would be lovely
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
i plugged in my 18 month old iPhone to charge it, using the cable that came with it and that I have used regularly all along. I got a warning on my phone screen saying the cable is not certified and may not work properly with my iPhone. Why?
If you updated iPhone to iOS7, it now checks for real Apple Lightning Cable. Your cable may not be Apple, or someone swapped another cable with yours. Make sure the cable end is clean, take a clean dry toothbrush and carefully clean charging port on the iPhone.
-
I'm using charger and cable that came with the phone. Nothing else changed.
I think it was the update the iOS 7.0.4 that I did last night. I woke up this morning with my battery almost drained and the charging function going off and on every few seconds, like it would start charging then disconnect, then reconnect repeatedly.
I've tried restarting the phone and hard restarting the phone several times, but I'm getting really low on battery by now (under 20%).
I've tried cleaning the connector with a little isopropyl alcohol, and blowing it out with compressed air. Though I can't be 100% certain, it's very unlikely my connector died exactly at the same time I was updating my phone. Especially since it appears I'm not the only one with this problem.
And now, after the last hard reset, my phone doesn't even recognize the charger at all, or being connected with the USB cable to my MacBook Pro.
I turned off my phone so when I go to the Apple Store it will power up one last time, but besides that I'm out of ideas.Just back from Genius Bar and two other people at my table had the same problem. Their 4Ss aren't charging either. One of them had a fried board according to the tech. At least my HW checked out OK. It just won't charge.
The tech tried to tell me that it was because my connector was corroded, which I told him was kind of a weak argument since evidence points to that the update has something to do with it.
They're seeing a lot of these and it looks like they already have a script.
Luckily I had enough juice left to recycle it for like $180, so I picked up a 5S with a new 2 year.
It looked to me like this is going to blow up pretty big. Like class action lawsuit big.
If you have an iPhone 4 or 4S, and you haven't updated it to iOS 7, don't for now. See if a patch comes out that doesn't brick your phone. Or get an induction charger maybe? Don't just update and expect absolutely no problems because too many people are having problems right now. -
"charging is not supported" when using the cable that came with ipod
I get an error message that "charging is not supported" when plugged in using the only cable that came with my ipod touch. My ipod will charge for 5 minutes then when I check on it, I notice this error on screen and the ipod has stopped charging. I'm using the same charging method I have always used since I owned this ipod which has been over 2 years now and this only started happening recently. I believe this started when I upgraded to 5.0.1.
- Look at both partsof the 30 pin dock connector. Log for bent. mising or corroded contacts of orther abnormalities. The cable could be bad. Try a new one.
- Try a reset. Nothings is lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears. -
Can anyone please help me. I have had my ipad2 for about 5 months and it has worked fine. I am now having issues charging it. I am using the cords that came with it and the outlet that I have used to charge it in the past, but when plugged in it is recconoigzed, but states not charging. I have made sure all my updates are current and they are. Does anyone have any suggestions or helful advice that my help. Thanks in advance.
Are you plugging it into a pc? If so it will not charge the iPad as there is not enough power try the back USB ports, may work.
If it isn't plugged into a pc and plugged into your socket could be faulty socket adapter. -
Do I need the cable that came with I home iw3 to connect my ipad air or can I use the ipad charging cable with an adapter to connect?
Just from personal curiosity, which web pages did you visit with your question that had you end up here in the 10.3 and earlier forum Circa 2003 obsoleteware?
It seems a common fault with this Apple Spoort site that so many posts are made to this forum that are irrelevant.
Can you post a few links from your browser History, just for research?
To answer your question, to upgrade from 10.5 to 10.6 you need to purchase the 10.6 retail DVD such as from here.
http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
(For your home country use the Apple localised site.)
The DVD is reasonablly priced, and once installed you can upgrade your iTunes etc. -
HELP!!! My ipod touch 4th generation is not charging! The cable that came with the ipod touch is not charging the itouch, I have to use an iphone 3's cable to charge. What should I do?!?!
Get a replacement cable. If still under warranty, Apple will replace the cable.
-
Why does only the USB cable that came with my phon...
I recently acquired a Nokia Lumia Icon from Verizon. I have a Lenovo Yoga Pro 2 computer running Windows 8.1 with the Windows Phone App for Desktop (WPA4D) installed. I had a very difficult time getting my Icon to be seen by my computer when connecting it with one of the half dozen micro USB cables I have laying around. WPA4D would not recognize it. Then, I connected it using the USB cable that came with the phone, and WPA4D immediately recognized it. Then I unplugged it and went back to a different cable - it was again not recognized.
What is different about the USB cable that ships with the Nokia Lumia Icon? If I want to order more, like from Monoprice, what do I order to get the same thing? Why is Nokia (apparently) using some sort of proprietary cable??
Thanks,
EricIt is not proprietary.The charging/data cable for my GPS works.
A lot of the cables are just for charging and that is all they are wired for and they don't even have the data pin. Full size USB cables are the same way.
If I needed an extra I would get it from Nokia. -
my iphone 4 wont connect to my laptop (windows 8) via usb but it will however register that it is there via 'photos' im not using the cable that came with my phone, does that affect the connection?
i just want it to connect to my itunes again!!!
Thank you to anyone and everyone that manages to help!Hello webster995,
Thank you for the details of the issue you are experiencing with your iPhone not appearing in iTunes. I recommend following the steps in the article below to troubleshoot the issue you described:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Thank you for using Apple Support Communities.
Best,
Sheila M. -
Can I use the USB cable that came with my digital camera to conect camera to iPad by connecying the camera cable to the USB end of the iPad cable? I have a double ended USB connector if necessary.
No.
You need to use this.
http://store.apple.com/us/product/MD821ZM/A/lightning-to-usb-camera-adapter?fnod e=3a
or this
http://store.apple.com/us/product/MD822ZM/A/lightning-to-sd-card-camera-reader?f node=3a -
Error "printhead problem please use setup cartidge that came with the printer"
Hi, I have purchased a HP Deskjet 5525 All in one printer, it was working perfectly till 1 year, then i had not used it about 6 months, now when tried to use it again then it was throwing the error "Printhead is damaged, missing, not installed properly or damaged etc...", then i cleaned the printhead and reinstalled it in printer then i inserted the cartidge now its generating the error "please use setup cartidge that came with printer" but among the setup cardige "yellow", "magenta", "Cyan" is accessible by printer but when i use the black then it says "properly not installed, missing cartidge".
So please tell me do i need to purchase a new black cartidge, will it work? or what shoud i do ?
cartidge NO- 685
Thanks
NirmalHi @nirmal007,
Welcome to the HP Support Forum! I understand you're having cartridge issues with your HP Deskjet Ink Advantage 5525 e-All-in-One Printer. I would like to assist you with clearing up that error state and have some troubleshooting steps that may resolve the issue.
I recommend you try the following steps before you consider purchasing a new black ink cartridge. Firstly after you've confirmed that your ink levels are not the problem (example - the level is above 10%), try a 'hard reset':
Secondly:
Make sure that the ink cartridges are properly vented and seated correctly
If the vent on the top of the ink cartridge is clogged or obstructed, the ink cartridge might not work properly. Follow these steps to make sure that the ink cartridges are properly vented and seated correctly.
Press the Power button to turn on the printer, if it is not already turned on. Wait until the printer is idle and silent before continuing.
Open the cartridge access door. The carriage moves to the access area.
Figure : Open the cartridge access door
Press the tab on the front of the cartridge inward to release it, and then pull up on the cartridge to remove it from the slot.
Figure : Remove the cartridge from the slot
Examine the vent area on each cartridge, above the HP logo on the top of the cartridge.
Figure : Vent area on the top of the cartridge
If the cartridge still has the orange pull-tab attached, pull to remove it.
Figure : Orange pull tab
If the vent is clogged, use a straight pin to gently remove excess adhesive from the vent.
Figure : Clean the clogged vent with a pin
Clogged vent
With a straight pin, gently remove excess adhesive from the vent
Unclogged vent
With the nozzle and contacts facing down, slide the cartridge into its slot. Press down on the cartridge until it clicks into place.
note:Make sure that each cartridge is installed in the correct slot. Match the shape of the icon and the color of the cartridge with the slot that has the same shaped icon and color.
Figure : Reinsert the cartridge
Repeat these steps to inspect the vents on each of the cartridges.
Make sure that each cartridge is firmly in place in its slot. Run your finger along the top of the cartridges to feel for any that are protruding, and if any are, press down firmly until each cartridge snaps into place.
Close the cartridge access door.
Figure : Close the cartridge access door
Source
Thirdly, try cleaning your cartridge contacts:
Manually cleaning the print cartridge contacts
Follow the steps below to manually clean the print cartridge contacts:
Gather the following items to clean the contacts:
Distilled water (tap water may contain contaminants that can damage the print cartridge)
Cotton swabs or other soft, lint-free material that will not stick to the print cartridge
Open the print cartridge door.
Remove the print cartridge and place it on a piece of paper with the ink nozzle plate facing up.
caution:
Do not to touch the copper-colored contacts or the ink nozzle plate with your fingersFigure : Do not touch copper-colored contacts
caution:Do not leave the print cartridge outside the printer for more than 30 minutes. Ink nozzles exposed to the air longer than this may dry out and cause printing problems.
Lightly moisten a cotton swab with distilled water and squeeze any excess water from the swab.
Gently wipe the copper-colored contacts with the cotton swab.
caution:Do not touch the ink nozzle plate. Touching the ink nozzle plate will result in clogs, ink failure, and bad electrical connections.
Repeat steps 4 and 5 until no ink residue or dust appears on a clean swab.
Insert the print cartridge in the printer, and then close the print cartridge door.
Source
If you've tried all of the above noted steps and you're still unable to use the black cartridge, you may need to pick up a new one. Let me know if this helps. Best of luck!
E-roq
I work on behalf of HP.
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping! -
I bought a used macbook pro that came with xcode
I bought a used macbook pro that came with xcode, this means I can develop Apps but to publish in App Store needed pay developer fees? Or must pay these fees from now?
All you have are the basic tools. Without a paid program in your name, you cannot distribute apps to the store.
See iOS Developer Program
Maybe you are looking for
-
How do I set a password to open firefox?
We use to have a password that was set to pop up on the opening of firefox. I recently updated firefox and can no longer find the place to do this again.
-
Flash lite problem,,,need help soon
why the protocol ftp is not suported by the flash player and how to make flash lite support ftp
-
Moving home - need info on existing operator
Dear forum users, I am a BT customer , and I am moving home, from Bermondsey to Tooting (both London postcodes). I used the on-line "moving home" link to proceed with the trasnfer, but at some point I had a warning: "We can supply phone service at yo
-
Disallow Payment Transactions MK02
Hi, Is there a way for me to disallow certain users from going to "Payment Transactions" in MK02? Thanks
-
I am using the SVT to perform SINAD tests on a few signals in my current setup, additionally i would like to perform Signal to Noise ratio are there any LabVIEW functions to do this (I noticed a dynamic range VI but i am unsure about its likeness to