My MacBook Pro is crashing and Mac OS stops working sometimes so I have to restart it. And sometimes it stays on the first white-ish screen with the Apple and won't start further. What to do?
my MacBook Pro is crashing and Mac OS stops working sometimes so I have to restart it. And sometimes it stays on the first white-ish screen with the Apple and won't start further.
What to do?
Does that mean that the is the end of my Mac Book 5bought in the summer of 2009) ? Or is there someting to do to fix it?
Thanks
V
Try this:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.
Similar Messages
-
Imac G5 stuck on white loading screen with gray apple and spinning wheel
I purchased this imac from a rebutable seller on ebay. He obviously had it working before he sent it to me, and he has been helpfull the whole way through, so I am positive this computer is not junk. When I recieved it, I plugged it in and turned it on, at first nothing would show up on the screen and the fans came on. Then, I contacted the seller and he told me to hold the shift key while turning it on. That did work to some extent. Now when I turn it on, it is stuck on the white screen with the gray apple and the spinning wheel. He had just updated and installed EVERYTHING imaginable so I am positive everything is up to date. I am not sure what to do, I have researched this but I cannot seem to find an answer. Oh, and even know on the white screen the fans turn on. It is quite weird.
Well, I hope someone can help. Thank you.Call AppleCare. You should not be having problems with a brand-new machine.
-
What do I do when I start my iMac I get a white screen with an apple and a moving circle?
All I get when my iMac is turned on is a white screen with an apple and a moving circle. What should I do to get the iMac to boot?
Do you have reliable backup you can restore from, as an erase and re-install may be required?
Before you got down that route, it's possible that it might get fixed if you try again. Not sure about that particular error, but I have had errors in the past that Disk Utility wouldn't fix on the first attempt but then subsequently did.
It's also possible that the (around $99, I think) Disk Warrior might resolve it - but not guaranteed.
However, I just found this thread: https://discussions.apple.com/thread/3862376?start=15&tstart=0 have a look at Nirvi's post at the end - there may be hope (I've not tried this, although it seems to have helped a few, although not everybody - so at your own risk and I wouldn't try it if I didn't have backup). -
I just started my Macbook air the first time, connected it with my wlan and know it asks me for a password and it does not accept the only password I know, what can I do?
It needs the user password for the wireless router, that would have been set by whomever installed the router, if that was you then try to find the password. If you can not find the password reset the router to factory default and set it up again.
-
MacBook will turn on to white screen with gray apple and loading bar, will load very little and then turn off. What do I do?
Bescobar23,
which model MacBook do you have, and which version of OS X is installed on it? -
i accidently downloaded something that made my webcam flash on spuradically even once i deleted it. when i restarted my computer it got stuck at the white loading screen with the grey apple and wont go past there..what is wrong? will applecare cover this? my computer also slowed down drastically before it stopped working..thanks! HELP PLEASE!
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider. -
I have a 2010 vintage 13-inch MacBook Pro that has a 60 watt power adapter. I also have an older power adapter that is 65 watts. Is it okat to use the 65 watt with this MacBook Pro?
yes.
"For instance If you have a MacBook (13-inch Late 2009) that normally uses a 60W adapter, you can also use an 85W adapter with that computer. You would not use a 45W adapter with that computer; it would not provide enough power for that MacBook. Using an adapter of higher wattage than the adapter that came with the computer will not cause the computer to charge more quickly or otherwise operate any differently than using the adapter that came with the computer. "
http://support.apple.com/kb/HT2346 -
hi, please help.
Accidentally deleted startupitems from library/startupitems on macbook now the computer wont startup and i get the grey startup loading screen with the apple symbol and a loading bar but wont load then turns off.
i saved these files to a folder on the destop and then turned the computer off. oops!!! now computer wont start up
How do i put the startupitems back to this folder or beter yet get into the computer to fix this.
Please please help!!!Reinstall OS X, either from disc or a recovery partition. You don't mention which version of OS X you're running so I don't know which it will be.
-
My computer froze so i manually restarted it. Since then, I haven't been able to proceed past the white loading screen with the grey apple on it. What should I do?
Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Just press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The RepairDisk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.
If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead. -
When updating my IOS 5.1.1 to IOS 6 and after the download completed the updating of the iphone couldn't be completed for unknown error and the device froze and all i have now is a black screen with an apple and a meter that shows no progress I can't switch off my iphone or do anything!!!
Hi,
I had a similar problem last week with my nice shiny 3 week old iPhone 6. I noticed the Apple logo was on the screen, but it did not progress like a normal boot up. I restarted the phone, and it showed the Apple logo, then a red screen then cycled back to the logo and kept looping. I got the phone to the iTunes connection stage by keeping hold of the power button and the home button until the apple logo appeared then kept holding the home button. iTunes recognised the phone, and wanted to restore, but this was unsuccessful because the phone would keep looping to the red screen and iTunes failed. After loads of Apple support, I was told it was a hardware failure, and like you I live more than an hour away from the store. None the less, I made an appointment with the Genius bods, and they replaced the phone. They said they had never heard of the problem, but really, take a look at these forums and you will see that it is a common problem and I suspect they are keeping it under wraps...
My issue is that as a disappointed customer with faulty goods, why should i have to stick to an appointment to get it replaced? What other store would you have to do this?
The "Genius" didn't even want to see the phone powered up before offering a replacement... Oh, and it turned out they didn't have the exact same model as a replacement so they were going to send me out of the store empty handed.... I kicked off BIG time, and they very reluctantly gave me a phone from the sales stock, rather than the repairs stock..
Not a happy Apple customer anymore, and I feel the more people who know about the lack of service and customer care the better. They need to get off there high horse and join the real world! -
I have an iPhone 5c. When I woke up this morning to take it off the charger, the iTunes icon was in the center of my screen with an arrow and a white plug illustration. I have rebooted and it is still stuck. Any suggestions?
Ante Boras wrote:
wich OS you are using?
@ ckuan: wich Jailbreak Tools? He wan't to jailbreak his iPhone. It's hang in the recovery mode, or i not understand right your quastion?
iPhone 5c & 5s comes with IOS 7, if you don't know.
You deleted the TinyUmbrella suggestion and act dumb?\ -
I tried to download IOS 7.1.2 but my phone has been frozen on a screen with an apple and a bar that hasn't progressed for 11 hours I have an Iphone 5S
Hold down the home button and the power button for about 25 seconds or until you see the apple logo. Thats a hard reset and it should restart the phone and bring it back to the slide to unlock.
-
Brand new MacBookPro 13" , Stuck at White Screen with gray apple and spinning gear.
Brand new MacBookPro 13" , Stuck at White Screen with gray apple and spinning gear.
This MBP apparently didn't come with a DVD and safe mode ( holding shift at boot up ) isn't working.
Any ideas would be most appreciated.Call AppleCare. You should not be having problems with a brand-new machine.
-
my ipod touch 4 gen. has a black screen with a apple and under it is a load bar that is empty and wont load
Try here:
iPhone and iPod touch: Frozen and unresponsive
iPod touch: Hardware troubleshooting -
Macbook Air - White/Grey Screen with a folder and a question mark
Out of the blue , my macbook air stopped starting up and strted to show me a white/grey screen with nothing but a folder and a question mark . After searching on the internet for solutions and trying to reset my PRAM setting , it still wouldn't boot up . I opened up disk utility and going through internet recovery , I ran the first aid verification on my MAC OS X Base System and it said that it found no problems . I can't restore or erase by the way and i really wouldn't erase my files as I have very important files on my mac . Moving on , I tried to reinstall OS X , but apperently it needs a disk to install OS x on and since none appear , I tried using an USB . After creating a partition and erasing everything on my USB , not happy about that , it wasn't big enough for the OS . So now I am basically stuck in the mac white screen Limbo .
Any sort of help would be fantastic and please do keep in mind that this is a macbook air and I do not have a place to put DVDs into . All I have read on different forum pages didn't help so i decided that it would be a good idea to create my very own thread . I am not very sure about the Mountain Lion version ,but I am not very sure that it matters .Out of the blue , my macbook air stopped starting up and strted to show me a white/grey screen with nothing but a folder and a question mark . After searching on the internet for solutions and trying to reset my PRAM setting , it still wouldn't boot up . I opened up disk utility and going through internet recovery , I ran the first aid verification on my MAC OS X Base System and it said that it found no problems . I can't restore or erase by the way and i really wouldn't erase my files as I have very important files on my mac . Moving on , I tried to reinstall OS X , but apperently it needs a disk to install OS x on and since none appear , I tried using an USB . After creating a partition and erasing everything on my USB , not happy about that , it wasn't big enough for the OS . So now I am basically stuck in the mac white screen Limbo .
Any sort of help would be fantastic and please do keep in mind that this is a macbook air and I do not have a place to put DVDs into . All I have read on different forum pages didn't help so i decided that it would be a good idea to create my very own thread . I am not very sure about the Mountain Lion version ,but I am not very sure that it matters .
Maybe you are looking for
-
How can I use my iPad 4gen as a MIDI controller?
Hello there, I have the iPad 4 generation. I have been reading that it is possible to use my iPad as a MIDI controller to help me with making music on my Windows computer and want to do this. What I've seen on the Internet from other people, is that
-
No programs will run even finder after an update even in safe mode
I tried installing the newest update in my macbook pro and after my comp ran out of battery no programs including finder will run even in safe mode. I get and error message that says finder quit unexpectedly over and over again. any help would be awe
-
hi experts as/400 to file scenario . i have configured the everything. adapter showing green. but i am unable to see the messages on the message monitoring. 1.data type for receiver .(REV_FILE) 2.ed(table definition)(ED_TAB) 1.receiver message type.
-
Hi, We are planning to implement CTS+ in our environment. We have Solution Manager system in NW 7.0 EHP1 SPS 2 levels. We are planning to use CTS+ for our XI transports. We are on XI 3.0, NW04, Basis 640 release, SPS 22 We will be using Solution mana
-
hi I am having some problems with SCCP gateway My analog phone doesnt have any tone when i configure it through SCCP gateway Need help dont know where am i making mistake Thanks