My macbook pro is moving on its own. Not sure if its being remotely controlled or if its a bug but its annoying!!

I have a 15inch Macbook Pro that has recently been acting wacky. It feels like someone else is controlling my computer but all my sharing featured are turned off and i have my firewall on so i doubt its being remote controlled. Using my cursor is a constant battle. Sometimes its fine other times it won't cooperate. At random times the cursor will move and highlight a word and define it. YES Define the highlighted word. While on safari it'll  randomly zoom in on the webpage im on,  and contiue to highlight and  try to switch pages. It'll switch from desktop to  dashboard on its own as well as  make my launch pad disappear and reaapear. without me touching it at all. SOMEONE HELP !

There are several possible causes for this issue. Please take each of the following steps that you haven't already tried until it's resolved. Some may not apply in your case.
1. Follow the instructions in this support article, and also this one, if applicable. A damaged or defective AC adapter could be the cause, even if it's the right kind.
2. Open the Bluetooth preference pane in System Preferences and delete all pointing devices other than the trackpad, if applicable. Disconnect any USB pointing devices. By a "pointing device," I mean a peripheral that moves the cursor, such as a trackpad, mouse, trackball, or graphics tablet. A plain keyboard is not a pointing device.
3. Start up in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you restart as usual, stop here and post your results. Do the same if you can't start in safe mode. If there was no difference in safe mode, go on to the next step.
4. Reset the System Management Controller.
5. If you're using a Bluetooth trackpad, investigate potential sources of interference, including USB 3 devices.
6. A swollen battery in a portable computer can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced without delay.
7. Press down all four corners of the trackpad at once and release. If there's any effect, it's likely to be temporary, and the unit needs to be serviced or replaced.
8. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built-in trackpad of a MacBook to  behave erratically. If you're using such an adapter, disconnect it and test.
9. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
10. If none of the above applies, or if you have another reason to think that your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
11. Make a "Genius" appointment at an Apple Store to have the machine and/or external trackpad tested.

Similar Messages

  • I want to use my iPad(4) as the remote for controlling my powerpoint presentation that is on my macbook pro(2012 no retina display). Not sure which is the best way to do so or which app to use.

    Going to be connecting my macbook pro to a projector. in the room there is no wifi either)

    Keynote Remote, but you will need wifi. You can set up an ad-hoc wifi network from your Macbook itself ("Create Network" from the Wifi menu), which the iPad can connect to.
    https://itunes.apple.com/us/app/keynote-remote/id300719251?mt=8
    Matt

  • Macbook PRO - Cursor has mind of own.  Lose control and don't know what is causing???

    Unable to control cursor at times.  Seems to have a mind of its own.  Know it is some software, but what and how do I correct???

    There are several possible causes for this issue. Take each of the following steps until it's resolved.
    1. Follow the instructions in this support article.
    2. Open the Bluetooth preference pane in System Preferences and check for unknown or forgotten input devices. Disconnect any USB input devices that you aren't using.
    3. Boot in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you reboot as usual, stop here and post your results. If you can't boot in safe mode, do the same. If you booted in safe mode and there was no change, go on to the next step.
    4. Reset the System Management Controller.
    5. If you're using a Bluetooth trackpad, investigate potential sources of interference, including USB 3 devices.
    6. A swollen battery in a MacBook Pro or Air can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced.
    7. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built in trackpad of a MacBook to  behave erratically. If you're using such an adapter, disconnect it and test.
    8. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
    9. If none of the above applies, or if you have another reason to think your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
    10. Make a "Genius" appointment at an Apple Store to have the machine tested.

  • I'm trying to extract audio files from my OLYMPUS Digital Voice Recorder VN-6200PC I am getting this error whenever I try to play its file type on my MacBook Pro,"The document "VN622195.WMA" could not be opened. The movie's file format isn't recognized."

    I'm trying to extract audio files from my OLYMPUS Digital Voice Recorder VN-6200PC
    I am getting this error whenever I try to play its file type on my MacBook Pro,"The document “VN622195.WMA” could not be opened. The movie's file format isn't recognized."

    The mac has no native way to read .wma files (these are Windows Media Audio files).  Do a search on the internet for playing wma files on a mac.  You will find several links to solution (one is to use flip4mac).

  • I recently destroyed my macbook pro and lost all my info.  I need to redownload my programs.  I bought CS5.5, but was upgraded to CS6 because it was purchased just a few weeks before its release.  How do I do this?  Thanks!

    Hi!
    I recently destroyed my macbook pro and lost all my info.  I need to redownload my programs.  I bought CS5.5, but was upgraded to CS6 because it was purchased just a few weeks before its release.  How do I do this?  Thanks!

    Downloadable installation files available:
    Suites and Programs:  CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
    Acrobat:  XI, X | 9,8 | 9 standard
    Premiere Elements:  13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
    Photoshop Elements:  13 |12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
    Lightroom:  5.7.1| 5 | 4 | 3
    Captivate:  8 | 7 | 6 | 5.5, 5 | 1
    Contribute:  CS5 | CS4, CS3 | 3,2
    FrameMaker:  12, 11, 10, 9, 8, 7.2
    Download and installation help for Adobe links
    Download and installation help for Prodesigntools links are listed on most linked pages.  They are critical; especially steps 1, 2 and 3.  If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'.

  • Just updated to my macbook pro to 10.8.2. ical not synching with my Exchange 2010 server. Worked flawlessly prior to the upgrade. Settings set to auto discover. I matched settings of a partner in my who is still using 10.7.1 without issues. Help!

    Just updated to my macbook pro to 10.8.2. ical not synching with my Exchange 2010 server. Worked flawlessly prior to the upgrade. Settings set to auto discover. I matched settings of a partner in my who is still using 10.7.1 without issues. Help!

    Also - my battery has been telling me "service battery" for a LONG time and then it switched to "replace soon" som time ago. Can't really see what this has to do with anything but whatever.
    That could conceivably explain all the problems you're describing. Replacing a Mac's battery should not be postponed since a failed battery will cause other problems to occur. It is also possible that its hard disk has failed, which means the information on it may soon become unrecoverable.
    ... my latest TM back up was from April 2014, can I just run this when I have rescued everthing and then it might not be as slow?
    If that Time Machine backup remains intact, it may be the only viable means of recovering that Mac's information. I suggest you do not attempt to restore its contents to your ailing Mac.
    Given that you are having trouble creating a newer Time Machine backup you should stop using that Mac immediately and have it serviced as soon as you are able. Do not take it to anyone other than Apple or a service facility authorized by Apple, for the very reasons you explained. If there are no Apple Stores in your vicinity search for an Authorized Apple Service Provider using the Contact Us link below. Use one of the options that appear under Contact Apple Support. The language on that page will be different for your location.

  • HT2513 I have a Macbook pro and I've lost my ical and widget icons. It says it's in the trash but I can't find it.

    I have a Macbook pro and I've lost my ical and widget icons. It says it's in the trash but I can't find it.

    Hey Shady K,
    It sounds like you've removed the iCal and Widget icons from your dock and want to get the back there for easy access. The following document goes over dock basics and there's a section (which I copied below) that goes over how to get those icons back on to the dock. Essentially you'll just find the application's icon in your applications folder and drag it back.
    Mac Basics: The Dock
    http://support.apple.com/kb/HT2474
    Adding and removing Dock items
    If you want to add an application to the Dock, click the Launchpad icon in the Dock and drag the application icon to the Dock; the icons in the Dock will move aside to make room for the new one. If you want to add a file or folder to the Dock, just drag its icon from any Finder window (or the desktop) and drop it on the Dock. The resulting icon that appears in the Dock is actually an alias of the original item (it's kind of a pointer to your original item). If you drag an application or file onto the Dock, you'll be able to open it anytime by simply clicking its docked icon. If you drag a folder onto the Dock, a Finder window of the folder's contents will display when you click the folder icon in the Dock.
    To remove an item from the Dock, drag its icon an inch or more off the Dock and wait a couple seconds, then release; the icon will disappear in a poof of smoke. There are some icons that you can't remove from the Dock, such as the Trash and the Finder.
    Don't worry, you aren't permanently removing the item from your computer; you simply got rid of its Dock icon. If you want that item back in the Dock, locate the application, file, or folder in the Finder (or with Spotlight), and drag it back into the Dock.
    Hope that helps,
    David

  • HT3964 I just opened up my MacBook Pro after a few days of not using it and it was frozen. I turned it off and back on and all I see is a white screen, there was a file with a question mark flashing for a bit but I can't do anything, please help me!!

    I just opened up my MacBook Pro after a few days of not using it and it was frozen. I turned it off and back on and all I see is a white screen, there was a file with a question mark flashing for a bit but I can't do anything, please help me!!

    Jerricayoung,
    you have a 13-inch Mid 2012 MacBook Pro. It’s modern enough that it supports booting into Recovery mode. To do so, hold down a Command key and the R key as you start up. It should eventually show a Mac OS X Utilities menu. Select Disk Utility from that menu; when the Disk Utility window appears, select the bootable volume from the left-hand side of the window. (It’s typically called “Macintosh HD”.) When the volume is selected, some buttons will appear on the right-hand side. If it’s not greyed out, press the Verify Disk button; if it is greyed out, or if it reports on errors that it found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu; that will restart your MacBook Pro in its normal mode. With luck, that will be enough to get you to your normal login screen, rather than the white screen.

  • 'MacBook Pro EFI Firmware Update (v2.3)' not installing

      'MacBook Pro EFI Firmware Update (v2.3)' not installing
            I've tried multiple times now to install this update. When I do, it downloads and my computer will restart around 5 times with the 'beep' the first time. Once its finished the restarts and resumes normally, I check the Software Update via the Apple menu and it still appears in the list of updates.
    What's the cause of this and what can I do to resolve this?

    Is your machine plugged in when you do this?  The firmware update will not take place unless your system is plugged in.  You'll just get a black screen that flashes a few times and it will eventually boot regularly back to what it was.  If the firmware is installing, you'll see a progress bar at the bottom of your display.

  • I am trying to install a brand new WD 500 gb sata internal hd in my macbook pro. the original install dvd does not recognise the hd. all hardware is ok. any help?

    I am trying to install a brand new WD 500 gb sata internal hd in my macbook pro. the original install dvd does not recognise the hd. all hardware is ok. any help?

    For some reason OS X disks (whatever edition or flavors) that are supplied with Apple products only seem to contain a limited knowledge of available hard drives on the market at the time of thier publishing. This (rather opportunistically) creates a "Best Before" stale-OS X-software-copy situation where upgrading to or replacing a defective internal SATA hard drive with a newer, better or larger one is a largely hit and miss affair.
    If you buy the latest and greatest disk drive available for any older Mac you are likely to run into unresolvable problems making a clean re-install of your own, old edition or flavor of OS X onto any newer or larger hard drive since the OEM (gray) "OS X Install Disks" that Apple supply with retail products seem to contain only time-sensitive lists/mapings of then-known target drives that the Drive Management Tool in the then-published old "Installer Software" will support.
    Presumably new (colorful "X") retail versions of OS X (10.whatever.whatever) also contain time-limited Installers with limited knowledge of and adaptability to/compatability with a limited number of old hard drives then kicking-around on the market.
    This is especially a problem nowadays since the countless "puny old" hard drives that have been on the market are largely obsolete in a few months time, as manufacturers continue to produce larger and cheaper units, discontinuing older puny products... So if your drive fails you need an exact old (or similar familial) replacement drive for your "backup copy of OS X" to do a fresh, clean OS X re-install. Otherwise you need to purchase a new retail version of OS X, since yours is now effectively obsolete. Purchasing an old, puny drive to re-install your version.flavor of OS X to avoid buying a new version of OS X is a rather false economy.
    If you still have a working old hard drive with your old polluted 10.version.flavor of OS X still working on it you apparently must clone it with Time Machine or the newest version of Disk Utility (disk image copying) to most newer, larger drives, and a clean reinstall to such new hard drives is not possible.

  • My Dad gave me his old Macbook Pro and I downloaded another version of Lion so it's tied to my ID and it worked but I cannot download and iLife apps at all? It doesn't even give me a choice to purchase it just say accept?

    My Dad gave me his old Macbook Pro and I downloaded another version of Lion so it's tied to my ID and it worked but I cannot download any iLife apps at all? It doesn't even give me a choice to purchase it just say accept? And gives me a dropbox that says that these apps are tied to another ID and I need to log into that ID in order to download it.

    The Apple Support Communities are an international user to user technical support forum. As a man from Mexico my first language is Spanish. I do not speak English, however I do write in English with the aid of the Mac OS X spelling and grammar checks. I also live in a culture perhaps very very different from your own. When offering advice in the ASC, my comments are not meant to be anything more than helpful and certainly not to be taken as insults.
    This is a common issue with second hand Macs. The iLife apps came bundled free on this Mac and they are registered to your dad's Apple ID. The only way for you to acept them into your Apple ID is for you and your dad to contact Apple Care, explain that he has passed the Mac to you and ask that the iLife apps be released from your dad's Apple ID so that you may accept them into your Apple ID.

  • My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?

    My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?

    Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
    Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
    When the Mac OS X Utilities screen appears, follow the prompts to reinstall the Mac OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac didn’t ship with Lion, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
    Don't install the Thunderbolt update -- it's defective.

  • In my macbook pro hdmi, usb & SD card reader not working

    In my macbook pro hdmi, usb & sc card reader not working.
    i have tried the SRM reset done, till not working started.
    Could you please resolve this problem,

    Welcome to Apple Support Communities
    Simply take it to an Apple Store or reseller if it's in warranty. Your Mac will be repaired or replaced for free because it looks a hardware problem rather than a software issue.
    If it's not in warranty, hold Command and R keys while your MacBook is starting up, and reinstall OS X. If it doesn't work, you can't do much more to solve the problem

  • I am new to iMovies.  When I make a video using the mic and camera in my Macbook Pro, the audio and video are not in synch.  Very annoying.  How can I fix this?

    I am new to iMovies.  When I make a video using the mic and camera in my Macbook Pro, the audio and video are not in synch.  Very annoying.  How can I fix this?

    DVD drives read the bottom of the disk, not the top. Smooth out the paper & try again.

  • I am trying to import songs to my new macbook pro from my old computer using home sharing. Both computers say that home sharing is now on but neither show up in each other's library menu. I am logged on with the same apple id for both computers.

    I am trying to import songs to my new macbook pro from my old computer using home sharing. Both computers say that home sharing is now on but neither show up in each other's library menu. I am logged on with the same apple id for both computers. and both are on a stable wireless connection

    Logging into itunes store on each machine wth different Apple IDs is OK Autorising each others machines with the other Apple ID is OK. This is completley separate from Home Sharing
    For Home Sharing to work you need to
    File > Home Sharing > Create Home Share.
    You need to select one of the two Apple IDs you are using and ENTER THIS ON BOTH MACHINES WHEN CREATING THE HOME SHARE.
    Home sharing will then work

Maybe you are looking for

  • Change the Colour of the title safe zones

    Is there a way to change the yellow tittle safe zone colour, to something that can be seen over all colours.  yellow cant be seen over white and it makes it very difficult to use, FCP 7 used aqua Blue it worked much better.   PLease help, Or Apple PL

  • How to set the variable height for TileLayout

    Hi, I am using TileLayout in  <s:List> component . TileLayout takes the maximum height of the children and draw the same height for rest of the children in all rows. Instead, I want to have all the rows with various heights if their children have dif

  • Tabular form - Client side Clone Row on apex 4.1 not work

    Hi all, j have a tabular form page where i have implemented Vika's clone row solution. (See http://htmldb.oracle.com/pls/otn/f?p=24317:49) Now, after migrating my application from Apex 3.2 to Apex 4.1 this feature not work. Clicking the Copy icon cop

  • How Can I use JTable Like Datagrid (Spreadsheet) and database

    Please how can I achieve the following in java: (1) Create a Grid (spreadsheets-Like) with JTable and be able to add new record (rows) as I reach the end of the last column during data entry. (2) Save the content of the grid to a text file as well as

  • AIR-CT2504-25-K9 (HA) Help needed

    Hi all, I got two AIR-CT2404-25-K9 and i need them in HA (Active/Passive) i would like to add a AIR-CT2504-HA-K9 but can someone tell me if i need one or two for an active/passive config. Thanks for your help!