My Macbook pro (late 2011) is burning up and the fan won't come on.

For about a week now my mac has bee burning up!! Even if I am not doing anything with it it is so hot.  The fan will not come on either....any suggestions?

Run the Apple hardware test (choose the extended test) to see if it picks up a hardware issue.

Similar Messages

  • Macbook Pro late 2011 not powering on. The charger shows a blinking dim orange/green light.

    Macbook Pro late 2011 not powering on. The charger shows a blinking dim orange/green light. I have tried pressing the small button on the side of the macbook pro to check the battery, but no lights show up.

    Hey Angelo_here,
    I'd run through these steps:
    If your computer won't turn on, try each of these steps:
    Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
    If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
    Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
    Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
    If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
    MacBook Pro: How to remove or install memory
    MacBook: How to remove or install memory
    Mac Pro: How to remove or install memory
    Mac mini: How to remove or install memory
    iMac (27-inch, Late 2012): Installing or replacing memory
    iMac: How to remove or install memory
    Reset the SMC.
    If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
    via: Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/TS1367
    Welcome to Apple Support Communities!
    Regards,
    Delgadoh

  • Macbook pro late 2011. Have power on the battery but doesn't turn on at all.

    Macbook pro late 2011. Have power on the battery but doesn't turn on at all. Not even a sound, my mac has stayed turned off in nearly a month and now its not working???
    Any ideas to what the problem could be?
    Regards// Michael

    If a SMC reset does not bring life to your MBP, make an appointment at an Apple store genus bar for a free diagnosis.
    http://support.apple.com/kb/ht3964
    Ciao.

  • MacBook Pro late 2011 screen goes blank and needs shutdown and superdrive spins 3 times before ejecting discs

    Hi everyone,
    I have a big problem with my MacBook Pro late 2011, suddenly while working without connecting the charger and it is 100% charged the screen would go black and I would need to hold the power button to shut it down and then power it up again, The second issue is the superdrive whenever I use a disc it spins it for 3 times before ejecting it to me, tried resetting PRAM and tried re-installing mac os x mavericks, but no solution so far and about the superdrive I bought a cleaner disc and tried to insert it, the superdrive would spin it 3 times and ejects it after that. Saw the disk permission solution and tried it once and I think there is a problem with that because this is the second time I try it and it was saying that there were problems.
    Sorry for being long.
    Thanks in advance.

    Depending on what you are doing on the computer, how hard you are working the computer, it should not overheat. And if it does it should shut down or get very slow because when it starts to overheat the CPU will be throttled back to a lower Ghz speed and or just shut down so it doesn't cause damage to the CPU. The Kernel Panics are a sign that something else is going on. This could be software or hardware.
    If after wiping the drives and reinstall Lion on the SSD if the system is running OK then the drives are fine, IE they are not bad. There is something else corrupting them. Again this could be hardware or software, but I doubt it is heat. And using the MBP ion clamshell mode should not cause overheating or excessive heating of either of the drives.
    Have you installed iStat Pro or Menu and kept and eye on the temps? If not install iStat Pro and keep and eye on the temps. I bet they do not get above the 150°- 180°F mark which although hot is not overheating.
    Be very careful when calling Apple. Removing the DVD drive and installing a hard drive in that bay could void your warranty. The DVD is not a User Removable part and Apple frowns on doing that. So if you call them do not mention that you have replaced the DVD drive with another HDD.
    Honestly I suspect you have a hardware problem. But the only way to know that is to install just Lion and your basic programs and run the system. Leave out any AV type software, if you are running some. If you don't get any kernel panics thenn install some of your other software, one programm at a time. If with just the OS and basic software you get a kernel panic then it is hardware related and needs to be checked out by Apple. If you do that re-install the DVD and the original HDD with just the OS on it before you take it in.

  • I have a late 2008 iMac with dual intels and the fans won't come on anymore.  About every 1 1/2 hours, it automatically shuts down to cool off.  Is there any way to manually turn it on?  Or, do they have to be replaced?

    About every 1 1/2 hours, it automatically shuts down to cool off.  Is there any way to manually turn it on?  Or, do they have to be replaced?

    I tried that with no improvement.  I think I might have to have the fans replaced.  do you know if this is a particularly difficult procedure?  Something wierd that I've noticed is that if I have a video on for more than several minutes, the fans comes on, and also when I am on a Skype video conference for awhile.  Otherwise, the fan jst doen't come on as the intels heaten up to the point the the auto shut down kicks in...any advise?  This definitely interupts my work!  Thanks for your help and input thus far!

  • Macbook pro late 2011 starting problem

    I'm running OS Maverics 10.9.3 version on Macbook pro late 2011. Few days ago the OS got much slower than normal system. Then i installed the the new OS but it was good for few hours. Then after few hours it became slower again. Then I changed the HDD and installed the new OS. But I found the same problem again. Then I removed all backup files from the HDD. After removing all items it became to work normally. But after 15/17 days later when i'm trying to turn on the macbook a flashing folder icon appears then i pull down the display for a while. When the lights gone then i turn on again and it works normally. I tried the internet recovery option by pressing the (ctrl+R) button but it takes much time. But nothing happened. What is the problem?
    Here is my etrecheck result:
    EtreCheck version: 1.9.12 (48)
    Report generated July 3, 2014 at 2:17:37 AM GMT+6
    Hardware Information:
      MacBook Pro (13-inch, Late 2011) (Verified)
      MacBook Pro - model: MacBookPro8,1
      1 2.4 GHz Intel Core i5 CPU: 2 cores
      4 GB RAM
    Video Information:
      Intel HD Graphics 3000 - VRAM: 384 MB
      Color LCD 1280 x 800
    System Software:
      OS X 10.9.3 (13D65) - Uptime: 0 days 0:30:14
    Disk Information:
      TOSHIBA MQ01ABD050 disk0 : (500.11 GB)
      EFI (disk0s1) <not mounted>: 209.7 MB
      Mac HDD (disk0s2) / [Startup]: 499.76 GB (373.05 GB free)
      MATSHITADVD-R   UJ-8A8 
    USB Information:
      Apple Inc. FaceTime HD Camera (Built-in)
      Apple Inc. Apple Internal Keyboard / Trackpad
      Apple Inc. BRCM2070 Hub
      Apple Inc. Bluetooth USB Host Controller
      Apple Computer, Inc. IR Receiver
    Thunderbolt Information:
      Apple Inc. thunderbolt_bus
    Configuration files:
      /etc/hosts - Count: 20
    Gatekeeper:
      Anywhere
    Kernel Extensions:
      [not loaded] com.gct.driver.gdmuwm (1.0.8 - SDK 10.4) Support
    Problem System Launch Daemons:
      [failed] com.apple.wdhelper.plist
      [running] com.gct.dts.gdme2dn.plist Support
    Launch Daemons:
      [loaded] com.adobe.fpsaud.plist Support
      [loaded] com.microsoft.office.licensing.helper.plist Support
    Launch Agents:
      [not loaded] com.adobe.AAM.Updater-1.0.plist Support
    User Launch Agents:
      [loaded] com.google.keystone.agent.plist Support
      [running] com.moeppfdpoohhdcaefbfpmabjipnohiif.updater.plist Support
    User Login Items:
      iTunesHelper
    Internet Plug-ins:
      Flip4Mac WMV Plugin: Version: 3.2.0.16   - SDK 10.8 Support
      FlashPlayer-10.6: Version: 14.0.0.125 - SDK 10.6 Support
      QuickTime Plugin: Version: 7.7.3
      Flash Player: Version: 14.0.0.125 - SDK 10.6 Support
      AdobePDFViewer: Version: 10.0.0 Support
      AdobeAAMDetect: Version: AdobeAAMDetect 1.0.0.0 - SDK 10.6 Support
      Default Browser: Version: 537 - SDK 10.9
      SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6 Support
      Silverlight: Version: 5.1.30317.0 - SDK 10.6 Support
    Safari Extensions:
      Best YouTube Downloader: Version: 1.5.1
    Audio Plug-ins:
      BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
      AirPlay: Version: 2.0 - SDK 10.9
      AppleAVBAudio: Version: 203.2 - SDK 10.9
      iSightAudio: Version: 7.7.3 - SDK 10.9
    iTunes Plug-ins:
      Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
    User Internet Plug-ins:
      Picasa: Version: 1.0 - SDK 10.4 Support
    3rd Party Preference Panes:
      Flash Player  Support
      Flip4Mac WMV  Support
      Perian  Support
      Tuxera NTFS  Support
    Time Machine:
      Time Machine not configured!
    Top Processes by CPU:
          3% WindowServer
          1% storeagent
          1% softwareupdated
          1% fontd
          0% syslogd
    Top Processes by Memory:
      114 MB com.apple.WebKit.WebContent
      82 MB Safari
      49 MB com.apple.IconServicesAgent
      41 MB ocspd
      33 MB WindowServer
    Virtual Memory Information:
      1.82 GB Free RAM
      895 MB Active RAM
      275 MB Inactive RAM
      908 MB Wired RAM
      437 MB Page-ins
      2 MB Page-outs

    Try this:
    Boot into recovery (OPTION key down)  and select the recovery partition.
    From the 4 option menu select Disk Utility.
    Run Disk Utility>First Aid, Verify and Repair.
    If it says the disk cannot be repaired, replace it with a new HDD.
    If it says it is good, take out the disk, place it in an enclosure and connect it to the MBP via USB.
    If it boots the MBP, then the internal SATA cable is faulty and should be replaced.
    Ciao.

  • MacBook Pro (Late 2011) calibration problem

    Hi,
    I have tried to calibrate the monitor of my MacBook Pro (Late 2011, Mountain Lion OS) with the Spyder4Express, but the monitor has a yellow cast after the calibration. I've verified the yellow cast by comparing my monitor with other calibrated monitors and with some photos printed with calibrated printers. Moreover, I have calibrated the monitor of another MacBook Pro with the same Spyder4Express and the result is different from mine, i.e. the same photo is displayed with different tones on the two monitors of the two MacBooks.
    As calibration parameters of the Spyder4Express I have selected
    Gamut = Normal Gamut
    Backlight = White LED
    and set LCD Native flag in the Preferences Panel.
    Any suggestions to solve this issue? I suspect that the graphic accelerator (Intel HD 3000) of my MacBook Pro doesn't support the calibration. Someone else had the same problem?
    Regards,
    Luigi

    Hi,
    I have tried to calibrate the monitor of my MacBook Pro (Late 2011, Mountain Lion OS) with the Spyder4Express, but the monitor has a yellow cast after the calibration. I've verified the yellow cast by comparing my monitor with other calibrated monitors and with some photos printed with calibrated printers. Moreover, I have calibrated the monitor of another MacBook Pro with the same Spyder4Express and the result is different from mine, i.e. the same photo is displayed with different tones on the two monitors of the two MacBooks.
    As calibration parameters of the Spyder4Express I have selected
    Gamut = Normal Gamut
    Backlight = White LED
    and set LCD Native flag in the Preferences Panel.
    Any suggestions to solve this issue? I suspect that the graphic accelerator (Intel HD 3000) of my MacBook Pro doesn't support the calibration. Someone else had the same problem?
    Regards,
    Luigi

  • Installing window 7 to macbook pro late 2011

    I am trying to install Windows 7  to a Macbook Pro (late 2011). I got this far: After downloading Bootcamp 5 and going into Bootcamp assistant and clicking both, a) Download the latest windows support software from Apple, &  b) install Windows 7 or later version.
    NEXT: Installed external 8G usb drive for Windows support software to download to
    NEXT: In about 10 seconds it downloads then never moves on the "visual" download scale????????   THIS IS WHERE I GET STUCK
    ANY HELP WOULD GREATLY BE APPRECIATED

    Welcome to Apple Support Communities
    As it looks like you can't download the Windows support software from Boot Camp Assistant, download it at the Apple site > http://support.apple.com/kb/DL1638 Follow the steps to burn it to the USB drive.
    Then, open Boot Camp Assistant and install Windows. Don't mark the option to download the Windows support software

  • After upgrading to yosemite my macbook pro late 2011 does a random sound from time to time.

    After upgrading to yosemite my macbook pro late 2011 does a random sound from time to time. Its completely random and i already checked all apps in use and its not from them.

    Sounds like Notifications app.
    Maybe some other app. In SystemPreferences->Users&Groups->LoginItems tab: remove all entries with the minus sign underneath. This will not uninstall anything, you have to start those apps by hand now. Restart.
    Still there?
    Yes: Restart again while holding the shift key, this will start the mac in SafeMode: only the necessary items are loaded to run.
    Still there?
    Yes: Make an etrecheck list and post it here.
    No: Restart, put the items in the LoginItems back, one by one, restart after each entry, and you will find the "culprit"
    Please report accordingly. I will be back in 24 hours.

  • How do i use my imac 21.5" 2011 as a display for my macbook pro late 2011, through thunderbolt cable ? I have tried and it doesnt seem to work, neither does target disk mode.

    How do i use my imac 21.5" 2011 as a display for my macbook pro late 2011, through thunderbolt cable ? I have tried and it doesnt seem to work, neither does target disk mode.
    Could it be a borked cable ? I just bought it new from the store today, i have updated both imac and macbook pro to latest thunderbolt firmware and updates. Both 10.7.3.
    MacBook Pro:
      Vendor Name:    Apple, Inc.
      Device Name:    MacBook Pro
      UID:    0x0001000A17016E60
      Firmware Version:    22,1
      Port:
      Status:    No devices connected
      Link Status:    7
      Port Micro Firmware Version:    FFFF.FF.FF

    You are correct, here is what Apple Says:
    http://support.apple.com/kb/TS3775
    I was able to find these instructions, however they referr to 2009-2011 27" iMacs. I think it's the same, if it's not then contact Apple directly for instructions. If either of the machines is less than 90 days old or covered by AppleCare then call AppleCare tomorrow for help, they should be able to easily answer this for you. You will find the number in your manual or you can use the AppleCare Contact Info link.
    Your iMac should automatically recognize the presence of a digital video signal at the Mini DisplayPort and enter Target Display Mode.
    If your iMac does not automatically enter Target Display Mode, press command + F2 to manually enter Target Display Mode.

  • Both Internal hard drives fail on Macbook Pro late-2011

    Both internal hard drives (SSD and HDD) failed on Macbook Pro late-2011.
    Setup: MBP closed with Thunderbolt display attached.
    Problem on HDD-A
    I called Apple Support to log an issue with my MBP2011. The system is made up of 2 drives - SSD (128GB) and HDD with 2 partitions HDD-A and HDD-B(original 750GB).
    HDD-A has LionOSX 10.7 and HDD-B is storage. SSD has LionOSX on it as well. I normally boot HDD-A.
    I was working on HDD-A and the Kernel Panic screen appeared prompting me to shutdown the machine and start it up again.
    I tried to reboot HDD-A and the grey progress bar appeared for a long time. I then forced shutdown and rebooted into SSD.
    I was able to boot from SSD and then I opened Disk Utility to check the drives. I verified the disk for HDD-A and there was an error. I then tried to repair disk and it couldn't repair it. A dialogue said the disk could not be repaired and that data should be backed up.
    HDD-A was not visible in Finder but HDD-B was accessible.
    I verified HDD-B and it was "ok".
    I shutdown, booted from SSD, disk utility HDD-A and the same message occurred.
    I called Apple Support and they advised that I boot from my external HDD which was a clone of HDD-A.
    Solution
    I was successfully able to boot from the Clone HDD-A.
    HDD-A was able to be accessed and I could retrieve the files from HDD-A.
    I copied over the latest files from HDD-A to an external drive.
    Same Problem on SSD
    Boot from SSD, i started working for about 3 hours, with the lid closed, and attached to the ACD.
    Kernel Panic screen happened again on the SSD.
    Couldn't boot boot from either SSD or HDD-A.
    I booted from Cloned HDD-A, Disk Utility verify and repair returned errors on SSD. The same issue had occurred on the second drive.
    Disk Recovery from a boot recovery USB thumb, Disk Utility, erased SSD, verify was ok.
    Tried to install then there was an install error saying that SSD was damaged (large triangle warning icon). Tried 3 times, failed.
    Boot from Recovery Drive HDD-A, downloaded LionOSX.
    Next steps
    Format HDD-A and HDD-B into 2 partitions
    Install LionOSX on HDD A.
    Note:
    I did not do any software updates for about a week before 14.04.2012 and suspect it might be due to the virus.
    I normally work with the lid closed and attached to the ACD, I also suspect that overheating caused both drives to fail. However, I have been using this system with the lid closed for atleast a week. One Kernel Panic screen occured.

    Depending on what you are doing on the computer, how hard you are working the computer, it should not overheat. And if it does it should shut down or get very slow because when it starts to overheat the CPU will be throttled back to a lower Ghz speed and or just shut down so it doesn't cause damage to the CPU. The Kernel Panics are a sign that something else is going on. This could be software or hardware.
    If after wiping the drives and reinstall Lion on the SSD if the system is running OK then the drives are fine, IE they are not bad. There is something else corrupting them. Again this could be hardware or software, but I doubt it is heat. And using the MBP ion clamshell mode should not cause overheating or excessive heating of either of the drives.
    Have you installed iStat Pro or Menu and kept and eye on the temps? If not install iStat Pro and keep and eye on the temps. I bet they do not get above the 150°- 180°F mark which although hot is not overheating.
    Be very careful when calling Apple. Removing the DVD drive and installing a hard drive in that bay could void your warranty. The DVD is not a User Removable part and Apple frowns on doing that. So if you call them do not mention that you have replaced the DVD drive with another HDD.
    Honestly I suspect you have a hardware problem. But the only way to know that is to install just Lion and your basic programs and run the system. Leave out any AV type software, if you are running some. If you don't get any kernel panics thenn install some of your other software, one programm at a time. If with just the OS and basic software you get a kernel panic then it is hardware related and needs to be checked out by Apple. If you do that re-install the DVD and the original HDD with just the OS on it before you take it in.

  • Osx 10.8.4 does not run macbook pro late 2011

    does any have issues after installing osx 10.8.4???  because i have an issue after i update my macbook pro late 2011 ,it doesn't start and only stay on the mac logo and appears the pointer i restarted many times and does not work the only option i had is  to reinstall the osx 10.8.3. can anybody help me with this issue??  thank you.

    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • My japanese macbook pro (late 2011) physical keyboard does not match with the on screen japanese keyboard in windows 8.1 so does caps lock

    I am using windows 8.1 pro on my Japanese macbook pro (Late 2011) and enabled japanese language but the problem is that when i press caps lock (lower left corner) it changes the input method from english to japanese. I checked my on screen keyboard (OSK) in windows and its different from my physical keyboard i.e. keys are different on my physical keyboard compared to OSK. Can anyone help me?
    Thanks
    Tenadona

    Can I suggest the following articles, which are worth reviewing?
    Boot Camp: About keyboards and key assignment for Microsoft Windows - Apple Support
    Boot Camp: Apple Wireless Keyboard keyboard mapping in Windows - Apple Support
    Boot Camp: Windows commands on an Apple keyboard
    Windows does require language packs to be installed, if you want the physical keyboard to match the on-screen keyboard.

  • I tried to install windows 7 in my macbook pro late 2011 but i tried to create partions after it installed and it turn to dynamic disks and ican't access mac or win 7 what should I do i cant format it because i dont have a backup

    I tried to install windows 7 in my macbook pro late 2011 but i tried to create partions after it installed and it turn to dynamic disks and i can't access mac or win 7 what should I do i cant format it because i dont have a backup

    It's not that you can't format it because you have no backup, it's because you'll lose everything when you do. Lesson learned. Always have a backup.

  • How do I install the recover portion of OS X 10.10.1 on my MacBook Pro late 2011? It is missing!

    When I boot up my MacBook Pro late 2011 while pressing the option key it should show the recovery icon which it doesn't.
    How do I install this portion of Yosemite?

    This was changed with Yosemite.  The recovery is hidden when booting with option.  Hold command and R when booting to get into recovery (without option).  If you see the globe, then it is actually going to Internet recovery, which means you do not have a local recovery.

Maybe you are looking for