My Macbook pro often won't start up since I installed Lion, and I have to shut it down using power button. My desktop icons don't appear and the dock won't open. I only have the little circle of color spinning endlessly. What's wrong now!
My Macbook pro often won't start up since I installed Lion, and I have to shut it down using power button. My desktop icons don't appear and the dock won't open. I only have the little circle of color spinning endlessly. What's wrong now!
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of this exercise is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
Note: If FileVault is enabled under Mac OS X 10.7 or later, you can’t boot in safe mode.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem(s)?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.
Similar Messages
-
Superdrive won't read DVDs since I installed Lion
Long story short - My hard drive died a few weeks ago. Everything was backed up on a Time Capsule. After installing a new hard drive, I went through and install each OSX I have had before transferring over my data and applications. I have a Macbook Pro Mid 2009 (came with Leopard). So, I went through, updated to Snow Leopard then Lion, then transferred over my data.
1. I bought a game recently. All the specs fit for my computer. Put it in my SuperDrive and it would neither mount nor be recognized by the computer. My computer said it was a blank disc and spit it out after spinning it around for 5 minutes. I tested the game disc on another computer (my brother's Windows one) and it worked fine.
2. After transferring my data over, my Adobe CS3 was having problems opening. I recieved a few messages about problems with the licenses and figured I would have to uninstall everything and reinstall everything. (Tried the license repair tool from Adobe too, couldn't get it to work). So I uninstalled everything I had from Adobe (using Adobe's uninstaller). I inserted the disc to be reinstalled and had the same problems. The disc kept spinning, wouldnt mount, and my computer said the disc was blank.
I have tested burned discs and film DVDs. All of them seem to work. I am just having issues with installation DVDs it seems. I have also tried mounting them in Toast Titanium and I can't get that to work either.
I took my computer to the Apple store, they said they could replace the drive or do testing on it for 5 days. I can't really afford to be with my computer for that extended amount of time right now nor do I want to drop $100 when this could be a software or firmware issue. My questions are:
1. Will upgrading to Mountain Lion fix or make this issue worse?
2. Are there any diagnostic tools I can run besides the AHT to find out if my drive is going to ****?
3. Are there any software related things I can do to get my discs installed? (IE Installation over a network, using ISOs ->which I tried with the game, couldnt get that to work).
Thank you!Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of this exercise is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
Note: If FileVault is enabled under Mac OS X 10.7 or later, you can’t boot in safe mode.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem(s)?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test. -
Hi community,
I installedthe new lion OS x on my computer yesterday and everything is fine. Everything? Almost: Lotus Notes is behaving silly. After firing up the program it freezes in operation and does not take any command any more. I cannot even shut the app down. After restarting the Mac the failure continues. My first thought was to just kill the app, remove the software and reinstall on the new lion...
But: How do I do that (Mac user since a week) as I am a bit lost in the ne menues...
I would be grateful if you would come back to me on this.
Cheers,
JohannesI was having the same issue.
I added the POSIX_SEMAPHORES=1 to the Notes Preference file to resolve.
IMPORTANT NFO:
Sometimes the latest TextEdit in Lion may automatically rename Notes Preferences, to Notes Preferences.txt.
So, before updating your Notes Preferences, it's recommended that you make a backup and then edit the file. You can use the 'mv' command in Terminal to rename the file and remove the .txt extension if you run into this issue by using the following command:
mv Notes\\ Preferences.txt Notes\\ Preferences
OK, moving on, here's what to do:
Update to or use:
Mac OX 10.7.3
Lotus Notes 8.5.3
Right click on the Notes Application in the application folder.
Use Show Package content option from menu.
Go to the path: Notes/Contents/Resources and edit Notes Preference and add this text to the end of the string:
POSIX_SEMAPHORES=1
Afterwards the Notes Preference file should reflect these values:
[Notes]
Directory=$
SharedDataDirectory=/Applications/Notes.app/Contents/Resources/English.lproj/Dat a
InstallMode=1
InstallType=6
POSIX_SEMAPHORES=1
Notes should work after a reboot.
Hope this helped someone. -
Macbook pro often reboot its self
macbook pro often reboot its self
Which OS X is installed on your Mac ?
Click the Apple () menu top left in your screen. From the drop down menu click About This Mac.
The version is noted there.
Troubleshooting advice can depend on that information. -
I transferred data from my Macbook Pro to my Mac mini but it forced me to make a new user for my old data. How do I transfer my music, pics, and docs from the "old" user to the new user (so that I only have one user instead of 2?)
Unless you transfer the files from Setup Assistant, Migration Assistant creates a new user with the data.
To transfer the files to your first user, you have to log on this new user, and copy all your files to /Users/Shard folder. This is a folder where you can put the files you want to share between two or more users, and all users can read and write in it.
After copying the files, go to your first user, open /Users/Shared folder, and copy the files to your user folders. If you migrated applications, you must know that they are stored in a common folder (/Applications), so you don't have to transfer them. To open /Users/Shared folder, open Go menu (in the menu bar) > Go to Folder, and type the folder -
My Mac book pro won't re-start. The apple sign stays on for a while, that little circle keeps spinning and nothing happens. After 10 minutes rebooting the screen turned blue and nothing was on. now I just re-tried and lots of pixels came up. what should I do? Thanks anyone.
My Mac book pro won't re-start. The apple sign stays on for a while, that little circle keeps spinning and nothing happens. After 10 minutes rebooting the screen turned blue and nothing was on. now I just re-tried and lots of pixels came up. what should I do? Thanks anyone.
-
I have a MacBook Pro bought in dec 2009. Currently has mountain lion osx installed. Worked like a dream until today. Randomly froze, so I restarted it. To find I got a grey screen. It wouldn't start. Also note my DVD drive doesn't work, but mountain lion was installed via App Store anyway.
So here's what I done so far:
tried resetting PRAM - No success
Done disk utility. Disk verified with no errors. I even re formatted disk. - no success starting.
Tried re installing mountain lion via download . It froze halfway installing -no success.
Tried backing up a time machine backup from my USB hard drive. It froze at 1% - no success
Tried booting from safe mode - no success
Tried the command line boot - no success.
Please someone help!Sounds like the hard dre has left the building, Died, in the Sh*tter, Gone to the hard drive resting place in the sky.
Buy a new drive connect it to the system with a SATA to USB adapter and see if you can install Mt Lion on that drive connected externally. If you can then the drive inside your system has failed.
Oh Wait!!!! You have the 2009 model. They are known for bad drive to logic board cables. So it may not be the drive itself but the cable going from the drive to the logic board. Do the same as above then if the system runs OK with the new drive connected externally install it in the system and see if it boots. If it does you are good to go. If it doesn't then it is more then likely the cable that hs failed.
I would suggest you also SAVE a copy of that download of Mt Lion and create a USB install drive from it using Lion Disk Maker, once you get your system up and running. -
Hi i recently bought 8gb of ram and installed it in my mid 2010 13' macbook pro, but whenever i start my computer it freezes at the apple sign in the startup. I just put back my default 4gb of ram back into my computer and it runs fine. Any suggestions?
jamiesfromportland, greetings: I do not take issue with your very valid reasons for purchasing RAM from Apple. However by recommending not to purchase RAM from third party vendors I would suggest is unfounded advice. Most of the problems that occur with third party RAM are attributable to the lack of adherence to the required specifications, viz. this post.
I would be willing to wager that purchasing RAM from reputable vendors such as OWC or Crucial one would find similar fail/success ratios as those purchased from Apple. In both cases this assumes that the specifications are adhered to.
I have always purchased RAM upgrades from third party vendors with no performance issues. True that I do so to save money but I do not skimp on quality.
Ciao. -
How does one continue to use Mail on the early MacBook Pro, Model 1,1, that is not upgradable to Lion? I have been running iCloud on my iPhone (OS5) and iMac (Lion) along with the MacBook Pro (OS Version 10.6.8) since November until now. Mail will no longer download on the MacBook Pro and keeps asking for my password.
Mail should still be usable with your machine - but you'll need to update the settings to conform to the requirements of your system. Check with your ISP (like ATT, etc.) for the settings that will work with your Mail. Once you've updated this, you should be able to email like before.
For example, my ISP required that I go to Mail Preferences/Accounts and make sure the details conform to your email settings.
I have no idea of what your ISP is or what the settings might be, but this is likely the source of the problem. -
I reinstalled iPhoto on my MacBook Pro. It opens, but only shows the loading bars and does not allow me to add pictures. How can I fix this?
Mac 101: File Sharing
Mac OS X 10.7 Help: Transfer files between two Mac computers
Mac OS X 10.7 Help: Set up a Windows computer to share files with Mac users
Mac OS X 10.7 Help: Use iDisk to share files
Mac OS X: Sharing your files with non-Apple computers
How to share a Mac's files with a PC and vice versa. -
I am wanting in input audio to a MacBook Pro running 10.9.4. Since there is only the internal microphone as an input choice, how do I accomplish this?
Not something I've ever done, but I found a 9-year-old article from MacWorld -> http://www.macworld.com/article/1041790/tapetocd.html - that explains it a bit. Apparently the only software that you need is GarageBand and a hardware interface. Just Google "copy audio cassette to mac" and you'll get tons of hits.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display -
MY macbook pro is slow to start up after log in. any suggestions on where to start addressing the problem?
Delete any items in System Preferences > Users & Groups (or Accounts) > Login Items
Same for HD > Library > StartupItems
Not enough free space on the startup disk can slow the system down.
Right or control click the MacintoshHD icon on your Deskop.
Click Get Info. In the Get Info window you will see Capacity and Available.
Make sure there's a minimum of 15% free disk space. -
Have macbook pro 15" early 2011, blank hard drive (new), Install DVD not available and an inadequate internet connection.
How do I install an OS in the thing ?
Can I purchase an installation disk? (I think it originally shipped with snow leopard 10.6.6)
My first time with Macs and I would love to get it going.
Thanks....You can purchase replacement discs from Apple:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support: Contacting Apple for support and service - this includes
international calling numbers.
You can upgrade the firmware to enable Network Restore: Computers that can be upgraded to use OS X Internet Recovery. After upgrading you can do the following:
Install OS X Using Internet Recovery
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
Why does my macbook pro often lose connection with the canon mx922?
why does my macbook pro often lose connection with the canon mx922? This happened with the HP printer as well.
This may answer your Bonjour questions:
http://support.apple.com/kb/PH11449
https://www.apple.com/support/bonjour/
Ciao. -
Picked up my new Macbook Pro Retina display on October 24th (2013). It runs Mavericks. Keeps freezing on me - with no pattern to it. Sometimes when it's backing up, sometimes when it opens, sometimes when I click on Safari. Only way out of the probelm is a crash shut down using the power button. Nothing else works. Anyone found a fix to this yet?
JRHSafe Mode deletes some system caches that may help.
Startup your Mac in Safe Mode
A Safe Mode boot takes longer than a normal boot so be patient.
Once you are in Safe Mode, click Restart from the Apple () menu.
Maybe you are looking for
-
My external Lacie Quadra hard drive accidentally switched off in the middle of "erase free space", and when I switched it back on Disk Utility was hanging. So I Force Quit Disk Utility and restarted it. Now when I try to erase I get "Secure Disk Er
-
My iphone (4) is stuck in recovery mode after trying to install ios 5
I successfully exited recovery yesterday using recboot, but then after retrying to install ios5 it failed again - this time with error 14, and its back in recovery mode and I can't get it to exit with recboot this time. When I plug it in to my PC, i
-
I have just setup a physical dg environment with a single primary and standby. I have setup the broker and the observer. Everything works as expected except one thing and I don't know if it's a problem or not. I have read conflicting information. The
-
Install Forms & Reports Services into existing home?
I have a server with Oracle Database 10G R2 installed. I also installed the Web Server from the companion CD into its own home to use for APEX. Now, I want to install Forms and Reports services. Can I use the same "html" home that I used for the web
-
Where can i find my class files??
i'm looking into a jsp file, and it imports a class named MailSequia.MailerBean. I get errors about certain class, i would like to know where it 's sopoused to be this class, is it in classpath?? or where it should be??