My MacBook pro will not start up. when I boot up, it stays on a white screen

I have a MacBook pro. My hard drive went out and I recently put a new one in it. Now when I Try to turn it on, it stays on a white screen and says loading but never does. I have Mac OS X install disc 1 and 2, and says when you put the cd in to hold down c, but every time I try, it just ejects the cd. Please help!!!Not sure of what operating system it has, or if it even has one. It had Mac OS X Snow Leopard. I am complete rookie to working on apple in general.

Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
     Note: You will need an active Internet connection. I suggest using Ethernet
                 if possible because it is three times faster than wireless.

Similar Messages

  • My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg():Socket is not connected

    My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected

    If running 10.7 or later hold down Command-R at Startup.
    This should invoke recovery Mode.
    Choose Disk Utility.
    Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
    Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
    If errors, run again until it comes clean or gets stuck.
    Report any error messages.

  • My MacBook Pro will not start up after entering correct password.

    My MacBook Pro will not start up after entering password.  Circle with an X in it and 'cancel' below it is on bottom of screen.  When clicking on cancel, nothing happens.  This just started last night.  

    Hi MJTOOTS,
    Since you are getting to the login screen, it is booting past the "gray screen" phase, so try the steps in this article, like a Safe Boot.
    Resolve startup issues and perform disk maintenance with Disk Utility and fsck
    http://support.apple.com/kb/ts1417
    You may also want to see if any of your Login Items are causing an issue.
    OS X Mavericks: Open items automatically when you log in
    http://support.apple.com/kb/PH14173
    Thank you for visiting Apple Support Communities.
    Nubz

  • MacBook pro, will not start up- drive begins

    MacBook pro, will not start up- drive begins?

    OK, then try this:
    Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    Since you can boot into safe mode successfully, I'm assuming the problem may be with a bad third-party extension or plug-in (such as a driver for third-party hardware or a bad Flash plug-in, for example.) It can also be a problem with a bad cache or preference file. If the above doesn't help then use a utility like Lion Cache Cleaner 6.0.5, Cocktail, TinkerTool Sys..., or OnyX to clean out user, system, and font caches.

  • My MacBook Pro will not powerup (even when connected to power supply).

    My MacBook Pro will not powerup (even when connected to power supply). The caps lock key is the only light on.

    Hi PatB11902,
    Thank you for visiting Apple Support Communities.
    If your MacBook Pro does not seem to power on, but the caps lock key will light up when you press the caps lock key, you are likely seeing a video issue.
    There are several steps that can help troubleshoot this behavior, found at this link:
    Apple computers: Troubleshooting issues with video on internal or external displays - Apple Support
    Start with these steps:
    Reset the system
    You can reset the Mac's parameter RAM and SMC.
    Start up in Safe Mode.
    If your Mac does not start up normally after these steps, here are some additional tips that can help:
    Troubleshooting: My computer won't turn on - Apple Support
    Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
    If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
    Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
    If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
    If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).
    Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
    Sincerely,
    Jeremy

  • My macbook pro will not start up. stuck on grey loading screen and spinning dial. HELP

    my macbook pro will not start up. stuck on grey loading screen and spinning dial. i shut it down last night and now when i try to turn it on it will not get past this page. lights and sounds work but nothing happens. please help

    Power it down by holding the power button down. Then try to power it up again. Post back. It would help if we knew what OS you are running, the model MBP...

  • After instaling the update for OS yesterday (saturday 7.10.2012) my macbook pro will not start. The instaling proses start but stopp after 2-3 minutes. I have started mayby 10 tims know but it stops every time. Help, its just a monts ago my iMac hard fail

    After instaling the update for OS yesterday (saturday 7.10.2012) my macbook pro will not start. The instaling proses start but stopp after 2-3 minutes. I have started mayby 10 tims know but it stops every time. Help, its just a monts ago my iMac hard fail

    Actually it sometimes gets a little further, the display will dim and the pointer will appear and then whoop it will turn off. if i do a verbose start up, it will finish all the steps, the white screen will appear and dim and then it will turn off.

  • My MacBook Pro will not start up - it was just on last night - what do I do?

    My MacBook Pro will not start up. I used it last night and it was fine.  What should I do?

    Try a SMC reset.
    http://support.apple.com/en-us/HT201295
    Do you get anywhere in the startup sequence?
    Ciao.

  • My macbook pro will not start up or turn on.  any suggestions?

    My macbook pro will not start up or turn on.  Any suggestions?

    I had the same issue I bought my MacBook Pro in Jan. my harddrive was bad and they had to replace it. I know the guy held down the shift botton for a little then pressed the power botton while still holding down the shift botton and it turned on but not completely since my hard drive was bad.

  • HT1379 My Macbook Pro will not start at all. I automatically get the Apple Icon and a pinwheel that keeps clocking. How do I fix?

    If anyone can assist with why my Macbook Pro will not pass the first screen, please respond. I have been getting the spinning pinwheel for a few days and cannot lg on now. In recent days I deleted some files and thought that would help the computer move a little faster but now it will not sllow me to access my account. Any suggestions on how to get pass the initial screen?

    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
    If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
    If 10.7.0 or later...
    Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
    If that doesn't help Reinstall the OS.

  • My MacBook Pro will not start up, any suggestions?

    My MacBook Pro will not boot up. I was aware of something odd when I switched it off a couple of hours ago  now when I push the 'on' switch something starts - fans I think, and the little indicator light on the front. Does anyone have any suggestions on how to solve this problem?

    I had the same issue I bought my MacBook Pro in Jan. my harddrive was bad and they had to replace it. I know the guy held down the shift botton for a little then pressed the power botton while still holding down the shift botton and it turned on but not completely since my hard drive was bad.

  • HT3964 macbook pro will not start on battery power works fine when plugged in

    My macbook pro 15 inch early 2008 model will not start on battery power but works fine when plugged in.

    check the battery info.. >about this mac>more info>system report and select "power" on the lefthand column.  How many cycles? What does it say about the condition? etc.

  • My macbook pro will not  start up. I get the apple logo and the little  start up waiting avitar. I tried everything including starting with my back up drive and nothing happens.

    My macbook pro mid 2012 will not start up. I was running bitdefender and when I went to see if it was done, I had the apple logo and the loading (winding circle) on the screen. I can not get out of this. I used my back up external drive and it did nothing. It did light up.

    samnleosgpa,
    you may have faulty RAM. Are you able to boot into your MacBook Pro’s Apple Hardware Test (“AHT”)? If so, try running it to see if it can detect a problem. If you’re not able to run its AHT, and you’ve upgraded your MacBook Pro’s RAM before, try reïnstalling its original RAM and see if you can get past the “-6002F” error code. If you aren’t able to run its AHT, and you haven’t upgraded its RAM or you no longer have its original RAM, then I’d recommend that you make an appointment at your nearest Apple store to have them diagnose the problem.

  • Macbook Pro will not start up.

    My macbook pro just locked up.  When I reset it, it did not/will not start up. It stays on the light blue screen with a file folder with a question mark on it. What do I do?

    Hold the option key while booting again, you should get a choice of OS X Lion as a boot option along with Lion Recovery Partition.
    Once in Lion, use the Startup option in System Preferences to set Lion OS X as the boot option.
    https://support.apple.com/kb/TS2570
    If this don't work, then hold command r and boot into Lion Recovery Partition and use Disk Utility to Repair the Lion partition.
    If both methods don't show something to choose or boot into something, then either your bootloader is hosed (tried installing Ubuntu/Linux?) or perhaps the drive is dead.
    Hold t boot the problem Mac into Firewire Target Disk Mode and connect it to another Mac and see if the drive appears on the desktop of the other Mac.
    If you tried to install Ubuntu/Linux, let me know I have a solution for fixing that as well, depending upon if you upgraded to Lion or not.
    https://discussions.apple.com/message/16276201#16276201

  • My macbook pro will not start after pressing the power button

    I have bought a macbook pro last year and now, I have a great problem since a few months.
    My macbook does not boot up, I hear no fan noices and no LED lights are blinking...
    Battey is full, but nothing happens (means system will not start up).
    I have also tried to start with the Power button - but the similar effect "NOTHING HAPENS".
    What I don't understand is, if I do nothing for one or two days and press then the power button, the system will start up and full functionality for a few days.
    And anytime I get the same problem again... and must wait also for a few days.
    Can anybody support me please.
    Thank you all in advance and looking forward to a fast reply.

    Try reseting SMU as suggested in link below
    http://support.apple.com/kb/ht3964
    Allan

Maybe you are looking for

  • On Firefox 13 the new tab page boxes are blank no matter how many times I visit a website

    I downloaded firefox 13 about a week ago and when I open a new tab the boxes that are supposed to display your most visited webpages don't work, if you go to your bookmark that says "Most Visited" that displays my most visited webpages fine but none

  • F4 help in Web Dynpro

    Hi, I have a requirement wherein I need to have  F4 help on a field (Storage location- LGORT) based on the plant . I do not have this filed Plant on the screen but can fetch that in the code. I have created a Ztable which will have all the data relat

  • IPhone 4 album display photo is not the "KEY" photo from Aperture

    Aperture sets a "KEY" photo to best describe the contents of an album of many photos. iPhone 4 ignores this key photo and uses a random, often obscure photo to display. How can I correct this?

  • How do I erase a app.?

    i want to erase an app. How do Ido this?

  • Sequence-RenderOnly-Mixdown crashes - Out Of Memory

    Out of Memory trying to use FCE Sequence->RenderOnly->Mixdown. The video that crashes is 19:30 min in length (and others as well). Plenty of memory (actual=3GB: recognized as 2GB: SysSettings->Memory&Cache shows 1649Mb = 90%); Plenty of disk set as F