My refurbished iPad 3 charged for first time it and charger got very hot is that normal

just replaced my refurbished iPad 3 with another. Tried to charge it for first time. Noticed it got very hot and so did charger. I don't recall my other iPad doing this is this a defect in the ipad?

Define "hot".
If fully drained both the battery (that essentially fills up most of the body of the device) and the charger will get quite warm, though not unbearable. Time to charge will vary according to device: my iPad 4 takes about 6 hours if almost flat, but takes about 40 min if at 75%.
Be sure to use ONLY its original charger OR chargers that are rated for iPads. They draw twice the current as phones and will cause phone chargers to get much warmer than usual.

Similar Messages

Ipad mini charger getting very hot

ipad mini charger getting very hot. Not the ipad. What is it? A problem, or normal?

Warm is normal. Too hot to handle, literally, is not. So if you can hold it, then it's probably fine. Mine gets hot when it's charging. But if it's too hot for you to hold then you should stop using it and get it checked out an apple store.

How to plug ipad to pc for first time

how do I sync my new ipad 2 to my windows xp? do i need a specific program?

Have you turned on the iPad an activated it yet?
If you have, make sure the computer is authorized in iTunes>Store>Authorize this computer.
Connect the iPad to the PC and iTunes should start up sync automatically. You need no other application except iTunes.

My charger gets super hot is that normal

My power cord gets super hot. I can not hold it while my mac is charging. I am worried it may cause a fire. Is this normal or a defective cord?

break in the feed lines, dont use it again, get a replacement.
be careful how you wind up your cable when done, almost ALL such occurances are due to haphazard winding up of the charging cable.

How do I sync my new ipad mini with my old ipad 2, without losing any apps or data in notes? I need step by step instructions for first-time sync with ipad mini. Thanks.

How do I sync my new ipad mini with my old ipad 2, without losing any apps or data in notes? I need step by step instructions for first-time sync with ipad mini. Thanks.

If you synced it many times, you have to have a backup. It's just a question of how old that backup is now. When did you last sync?
First of all launch iTunes on your computer and go to Edit>Preferences>Devices. Do you see any backups for you iPad in that window? If so, how new is the newest backup? That will be the backup that you will want to use. But remember that if you use that backup and it is one month old, you can only restore from that date back in time. Anything that you did on the iPad in the past month will not be in that backup.
Turn on the new iPad Minin and start activating OTA via WiFi. You will get to a certain point in the process where you will be given the choice to Set up as new, Restore from iCloud - or Restore from iTunes. You will want to select Restore from iTunes.
That is the short and sweet version. There are step by step instructions in this article. This applies to the mini as well as the iPad 4 or the iPad 3 for that matter.
http://www.everythingicafe.com/how-to-set-up-new-ipad/2012/03/16/

HT1476 if i bought my ipod touch 32gb in germany where the voltage is 220v and i live in America where the voltage is 110, i will have to wait to get to my home to charge it for first time or I can charge it here and change the voltage of the battery in A

if i bought my ipod touch 32gb in germany where the voltage is 220v and i live in America where the voltage is 110, i will have to wait to get to my home to charge it for first time or I can charge it here and change the voltage of the battery in America?
please i need help, im worried that if I connect my ipod here, it will burn or sometihng bad.

Just connect it to a computer's USB port.
Most wall chargers are dual voltage (110- 220 volts) and only require a plug adopter. Check the wall charger to see if yours is.

HT4859 i have setup an ipad without connecting to computer, i am now connecting for first time to itunes it asks if i want to set up as new ipad or restore from previous backup (my iphone not ipad), i have backed ipad up to icloud when i connect back to i

i have set up my wifes ipad mini wirelesly, i am now connecting for first time to itunes it asks if i want to set up as new ipad or restore from previous backup (my iphone not ipad), i have backed ipad up to icloud when i connect back to itunes will it give me an option to restore from icloud, i dont want to lose the apps and data my wife has already installed through her account... any thoughts

1. set up as new
2. transfer you wife's purchases.
3. Just in case create one computer back up manually.
Enjoy.

TS3274 its almost 10 months,i purchased ipad2 32 3g wifi.itinially i got problem with applications shut off frequently now since last 4 months my ipad starts with a message (connect iTunes)like first time start and going to restore mode and it occurs freq

its almost 10 months,i purchased ipad2 32 3G wifi.itinially i got problem with applications and safari shut off frequently now since last 4 months my ipad starts with a message (connect iTunes)like first time start and going to restore mode and it occurs frequently.plz advise.

If you have followed the standard Apple troubleshooting processes (see user guide )
probably a trip to the local Apple Store Genius bar is called for before warranty runs out
Assuming the iPad has been released in your Country if not you may have to take it to a
neighbouring Country where it is available
This page will tell you ,via the drop down menu Countries that can support iPad
http://support.apple.com/kb/index?page=servicefaq&geo=United_Kingdom&product=ipa d

I hate to say - DISATISFIED WITH with CUSTOMER CARE RESPONSE and VERIZON in all for first time.

I am currently on National 900 plan on Motorola Droid. I switched from AT&T primarily because I love to use data on mobile. Verizon provided me the unlimited plan. I was a very happy customer with Verizon untill now.
Scenario -
Today, I called up Verizon customer care executive to see why bill for the month was not readjusted. Can anyone believe it its staggering $1137.73 [Roaming charges 1019.19].
Since this January, I am visiting to Canada. On first visit in January, I called up customer care to see what options I do have to use my phone in Canada as I use it in US. Verizon had a wonderful plan - just the monthly data plan is escalated appear. 30-40$ extra than the normal appear. 29.99$ plan. I happily added that plan before visiting Canada. While there is Canada, I did get notification couple of time that I am exceeding data limit but again checked with customer care later - they readjusted the bill as that was 'FALSE ALERT' as I was on unlimited data plan while roaming as well in Canada since I paid the additional prorated of (30-40$) for period of my stay there.
This equation worked for first and second visit - Unlimited Data while I used to get FALSE ALERT.
On my third visit , things changed - Verizon stopped providing the unlimited data services. I called up as usual before this visit. Customer care executive said - you are set to go to Canada now. I was not very specifically told on call that the rules have changed now and there is limit to data usage while roaming. During this visit also, I got the alerts - I assumed this was also a FALSE ALERT like prior one.
But this time, it was not FALSE ALERT, now I charged with this fee. I raised my concern and called up customer care appear. 10 day before [today is March 6th], they assured me that it is going to be re-adjusted ONLY for this time. And, they also asked to check account after 48 hours and if not readjusted please call. But, I checked my account today and it was not readjusted. So, I called up customer care executive for half an hour -- not willing to listen to any logic of mine and he said politely 'SIR, WE CANNOT READJUST YOUR BILL' . I am still trying to figure out where is my fault when I was not told DATA PLAN HAS CHANGED FROM THIS VISIT.
I hope senior management will look into this matter and re-adjust current bill. It's due this March 10th. I would appreciate any positive response prior to this so that I can pay the bill and BE A HAPPY VERIZON CUSTOMER.
Sincerely,
Manoj K. [removed personal information]

I called them back yesterday night, not willing to listen my story. Sir we sent you SMS notifications. But these notifications, I also got when I had unlimited plans on first and second visit. Then customer care told SIR you don't need to worry - but this time I should have been very specifically told rules are changed before changing my plans which I wasn't. I was under impression that I am on same unlimited plans.
A job not well done in COMMUNICATING TO CUSTOMERS and using that an opportunity to OVERCHARGE $1100 - INSANE for one month bill. None of my fault. SMS notification is no communication as earlier SMS noitification were false positive and bills were adjusted as I was on unlimited data plan.
Now you change the rules and send SMS Notification; RULE CHANGE, one is not aware of.. ANY NORMAL person will treat SMS notification as FALSE ALERT.. isn't it??

HOW TO add a videos or movies to IPOD TOUCH for first time...

HOW TO add a videos or movies to IPOD TOUCH for first time...
pls send step by step detail wise.. if you have a video for this ..pls mail me...
my email : [email protected]
thanks to all

See:
iOS and iPod: Syncing photos using iTunes
iOS: Syncing with iTunes
iTunes: Frequently asked questions about viewing and syncing videos
iTunes: May be unable to transfer videos to iPhone, iPad, or iPod

Long time to open workbook for first time

Hi,
I have a workbook with three queries . Performance of workbook is good when it was created for first time. It has additional 22 sheets with formulas and other sheets with values based on query sheets.
The problem starts after I close the existing session and open in another session when it takes 15 to 20 minutes to come up.But after that the book is slow even for single click button action.
Version of analysis 1.4.6
Win 7(64 bit)
Ms office 2010(32 bit)
Refresh on opening is disabled.
Few thing which I did:
>> I opened up task manager and did analyze wait chain, I found that excel.exe is waiting for splwow64.exe process.
>> I enabled logging at "debugging information" in support setting for workbook and checked things out in log file.
Found that
There was warning "AddSerializer failed (Command processors not initialized)
Looking at log file for events when book took time to open, I found that time stamp gap between following events"
-verbose: Working mode as serialized in document:'Local'
-verbose: Successfully deserialized system info from workbook XML
- verbose: ...its logs various properties of queries like query name,id etc"
and its immediate previous event of cache formula string is 20 mins.
>> in another session I opened a workbook with normal performance.Found above mentioned warning message and deserialization... information.
the difference in this case is that there is not delay in events.
Has anybody faced this issue? Any idea on deserialization of workbook xml in analysis.
Any idea where is metadata saved in analysis. is it in form of some hidden script object just as in BEx 7.0
Thanks
Pramod.

Hi Pramod,
Since you have several sheets in this workbook, have you checked the number of custom styles?
Please check the SAP note http://service.sap.com/sap/support/notes/1899658
According to the note, too many styles slow down Analysis for Office.
The note also contains a macro that you can run on your workbook to delete the custom styles if you want to check.
Regards,
Filipe

HT201250 i am using for first time the time machine and an external hard drive because I want to erase my macbook and start from zero files. do i keep my files in the portable hard disk when I connect it again with the macbook or the time machine will era

i am using for first time the time machine and an external hard drive because I want to erase my macbook and start from zero files. Am i keeping my files in the portable hard disk when I will connect it again with the macbook or the time machine will erase all?
I would like to know if after I erase all my data, empy hard drive inside the macbook, the time machine will erase all my files that I have saved in my "WD "My passport" external hard drive

Welcome to Apple Support Communities
Time Machine has to erase the external disk in order to make backups. Before setting Time Machine up, copy the files of your external disk to the hard disk of the Mac in order not to lose them, and then, set up Time Machine. The first backup will start automatically.
If you want more information about Time Machine, read the Pondini's site > http://pondini.org

Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message

Using iPod shuffle 4th generation for first time and receiving the error : one of the USB devices attached to this computer has malfunctioned, and windows does not recognize it. For assistance in solving this problem, click this message.
Using win 7 and latest iTunes [10.6.3]. Have already gone through below links and did not find any solution.
http://support.apple.com/kb/HT2292
http://support.apple.com/kb/TS1369
http://support.apple.com/kb/HT1923
http://en.kioskea.net/forum/affich-17997-ipod-not-detected

I was hoping it would be something like a USB device conflict, but now the shuffle is the only thing connected...
This article was one of the ones you linked to above in your initial post
http://support.apple.com/kb/TS1369
Under Part 9. Verify that USB drivers are installed, did you try the steps in If only "Unknown Device" appears? That appears to be your situation.
Also, you said that the shuffle initially worked well enough to do a sync, then it had the same problem again. If you can get it to work again initially, before doing anything else, try the following. Select the shuffle in the iTunes sidebar, under DEVICES. Over to the right, go to the Summary tab. By default, the checkbox for Enable disk use should be unchecked. If so, check it and Apply the change. See if that makes any difference.
(If Enable disk use was already checked, try unchecking it and Apply the change. Basically, set it the "other way" and see if there is any improvement.)
NOTE: When disk use is enabled, you have to eject the iPod in iTunes before disconnecting it physically.
If the disk use change makes a difference, that may provide a clue about the actual cause.

Performance issue in browsing SSAS cube using Excel for first time after cube refresh

Hello Group Members,
This is a continuation of my earlier blog question -
https://social.msdn.microsoft.com/Forums/en-US/a1e424a2-f102-4165-a597-f464cf03ebb5/cache-and-performance-issue-in-browsing-ssas-cube-using-excel-for-first-time?forum=sqlanalysisservices
As that thread is marked as answer, but my issue is not resolved, I am creating a new thread.
I am facing a cache and performance issue for the first time when I try to open a SSAS cube connection using Excel (using Data tab -> From Other Sources --> From Analysis Services) after daily cube refresh. In end users system (8 GB RAM but around
4GB available RAM), for the first time, it takes 10 minutes to open the cube. From next run onwards, its open up quickly within 10 secs.
We have daily ETL process running in high end servers. The configuration of dedicated SSAS cube server is 8 core, 64GB RAM. In total we have 4 cube DB - out of which for 3 is full cube refresh and 1 is incremental refresh. We have seen after daily cube
refresh, it takes 10 odd minutes to open the cube in end users system. From next time onwards, it opens up really fast with 10 secs. After cube refresh, in server systems (32 GB RAM, around 4GB available RAM), it takes 2 odd minutes to open the cube.
Is there, any way we could reduce the time taken for first attempt ?
As mentioned in my previous thread, we have already implemented a cube wraming cache. But, there is no improvement.
Currently, the cumulative size of the all 4 cube DB are more than 9 GB in Production and each cube DB having 4 individual cubes in average with highest cube DB size is 3.5 GB. Now, the question is how excel works with SSAS cube after
daily cube refresh?
Is it Excel creates a cache of the schema and data after each time cube is refreshed and in doing so it need to download the cube schema in Excel's memory? Now to download the the schema and data of each cube database from server to client, it will take
a significant time based on the bandwidth of the network and connection.
Is it anyway dependent to client system RAM ? Today the bigest cube DB size is 3.5 GB, tomorrow it will be 5-6 GB. Now, though client system RAM is 8 GB, the available or free RAM would be around 4 GB. So, what will happen then ?
Best Regards, Arka Mitra.

Could you run the following two DMV queries filling in the name of the cube you're connecting to. Then please post back the row count returned from each of them (by copying them into Excel and counting the rows).
I want to see if this is an issue I've run across before with thousands of dimension attributes and MDSCHEMA_CUBES performance.
select [HIERARCHY_UNIQUE_NAME]
from $system.mdschema_hierarchies
where CUBE_NAME = 'YourCubeName'
select [LEVEL_UNIQUE_NAME]
from $system.mdschema_levels
where CUBE_NAME = 'YourCubeName'
Also, what version of Analysis Services is it? If you connect Object Explorer in Management Studio to SSAS, what's the exact version number it says on the top server node?
http://artisconsulting.com/Blogs/GregGalloway

Error when launch MaxDB studio for first time

Dear, Experts
I faced with one issue for launch MaxDB studio for first time.
It reported:
Connect user failed
SAP DBTech JDBC: Cannot connect to jdbc:sapdb://.../.UMDB [Restart required].
Creating default user management failed
Could not create database ".UMDB": [C:\sapdb\clients\DatabaseStudio\pgm\dbmcli.exe] > ERR, -24832, ERR_SHMNOTAVAILABLE ...
Could you please help me on this?
Thank you in advance.
Best Regards

If not solved yet...
What says appsrv.log ? Which user are you using to start the appserver ? Which user have you specified when sreating the database ?
Nicolas.

My refurbished iPad 3 charged for first time it and charger got very hot is that normal

Similar Messages

Maybe you are looking for