N86 8MP problem with setup WLAN notifications

Hi,
how can I setup my N86 8MP WLAN notifications on display ( for example: WLAN networks found like on picture ).... I can´t find that options...please I realy need it... thanks....thanks
Solved!
Go to Solution.
Attachments:
nokia-n86-WLAN notifications.jpg ‏33 KB

Thanks....

Similar Messages

I am having problem with my push notifications of facebook and other applications on my 3gs ios5.0

Hi,
I am having problem with my push notifications of facebook and other applications on my 3gs ios5.0 device. I have done too many things have updated my facebook application but still it is not showing any push notification. Is there any settings that i need to do for it? Also it is not allowing me to show on mobile in facebook. Any one here can help?

ok for facetime and imessage go into settings turn them off make sure to make an icloud backup and then go to settings general erase all content and settings and then set it up from the backup it should activate your imessage and facetime

PLEASE HELP! Problems with Cisco WLAN and WPA encryption

I checked the threads and didn't see this posted. I have a Cisco WLAN card in my T42_2373_C88. It's a very unfortunate thing that this wireless LAN card/wireless config. utitlity doesn't support WPA encryption. I'm not entirely sure that it's the problem with the WLAN card, and the reason for this is that I initially set up a network through the Windows config. utility bypassing the IBM utility (which I can no longer do). I wasn't actually able to connect to my local network until I completely removed the profile for my home network in the access connections, only then was I able to connect (WPA-PSK (TKIP)). I saw some drivers available for my make and model on the lenovo.com driver site. I downloaded the drivers and went through device manager specifying the folder where the drivers were located and the drivers were not recognized by windows as valid drivers. Unless specifically told otherwise, I don't want to manually override and load these drivers. This is a business machine, and this specific wireless function is VERY critical.
Thanks

try using URLConnection instead of HTTPConnection.

I am have a lots of problem with push and notification. Its anyone else having this problem. This is very frustrating.

Hello . I don't know what to do anymore. I am having problem with push and notification. I have to go into the apple mail app to see my email. This is crazy. Is anyone out there with the same issues?

If it's happening on all apps that you've downloaded, but not on the Apple built-in apps, then try downloading any free app as that appears to reset something - you can then re-try your apps, and you can delete the free app.
If it's only happening on one or two apps then try closing them completely : from the home screen (i.e. not with any of the affected apps 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the apps to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work then you could try a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Problem with In-App Notifications

I keep having a problem with in-app notifications sicne my IOS 7 upgrade on my iPad Mini.
The notifications I'm on about, are as follows:
I'm in various Social Networking apps such as Skout, MeetMe etc You send a message or add a friend in that app. It comes up with the notifications "Friend Request Sent" "Message Sent" however there are no buttons underneath to press ok. You have to come out of the app, and then go back in.
This problem was occurring in IOS 7.0 and I updated to 7.0.2, however still having the same problem. I think this is an IOS bug which has not been found until now.

Was working. Stopped out of nowhere. Did not change any configuration, when stopped, tried to stir at all and does not work ...

Problems with Setup.exe LMS3.2 on Window 2008 Enterprise Sp2 32 Bit

Hi,
I have problems installing LMS 3.2. I get the following error during the installation process:
I already deactivated Windows Defender and DEP. After the Error the Installation finishes successfull. You can log in with the given credentials but when you are forwarded to the portal after login the browser shows "Page not Found".
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin-top:0cm;
mso-para-margin-right:0cm;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0cm;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Problem signature:
Problem Event Name:                        BEX
Application Name:                             setup.exe_InstallShield
Application Version:                           15.0.0.603
Application Timestamp:                     4a030a42
Fault Module Name:                          ErrStack.dll_unloaded
Fault Module Version:                        0.0.0.0
Fault Module Timestamp:                  4a1c4e04
Exception Offset:                                02ac26a0
Exception Code:                                  c0000005
Exception Data:                                   00000008
OS Version:                                          6.0.6002.2.2.0.274.10
Locale ID:                                             1033
Additional Information 1:                  b2be
Additional Information 2:                  82109204b3973566ace818217390e302
Additional Information 3:                  9025
Additional Information 4:                  5466bb6e3df7ad4e5cd4fca294d8db3a
Read our privacy statement:
http://go.microsoft.com/fwlink/?linkid=50163&clcid=0x0409
Regards
Mathias

This looks like CSCte84743.
Symptom:
Installation of CiscoWorks LAN Management Solution fails when the installer is trying to configure CiscoWorks Assistant. The error seen will be related to OpsConfUpdate.exe:
The application has failed to start because GGShared.dll was not found. Re-installing the application may fix this problem.
Conditions:
This can occur on Windows 2003 and 2008 servers. The underlying root cause is still not known.
Workaround:
Configure the following registry key value:
HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows\Installer\DisableRollback : DWORD : 0x00000001
Then, a clean installation of LMS should be performed. Once LMS is installed, this registry key value should be removed.
However, the problem with the page not found error could be CSCtb17186. If you try Firefox and get a redirection error, then that would confirm this bug.

SOLVED - Problem with setup online accounts

Good day,
I'm trying to setup gtalk on empathy, but I have a problem with adding me to online accounts. I just can't click to add account. It's inactive. Screenshot.
Do you have some advice for me?
Thank you!
Last edited by E_user (2012-07-16 09:42:21)

You might want to edit the thread title to something more descriptive.

Facebook App - Problems with Newsfeed & Missing Notifications/Messages

SOMEONE PLEASE HELP. I continue to have two frustrating problems with my Facebook for Blackberry app that I installed directly via RIM's website:
1. I am always missing notifications & messages on my blackberry. Sometimes they come through and other times they do not. Right now my blackberry said I had no new notifications or messages, but when I logged onto my Facebook account on my PC it showed I had 2 new messages. I have uninstalled and reinstalled the Facebook app three different times (each time also removing & reinstalling my battery). After doing this, it seems to work consistently for a short while (maybe a week or two) and then starts missing notifications & messages all over again. This is incredibly unreliable and frustrating - RIM really needs to fix this.
2. My second problem is that on my blackberry Facebook app I continue to see posts from apps that my friends interact with in my newsfeed that I have blocked on my main Facebook page (i.e. games like Farmville, Hidden Chronicles, various horoscope apps, etc). If I have blocked them on my regular Facebook account and they do not show up in my newsfeed when I'm logged into Facebook on a computer, why am I seeing them on my newsfeed on my blackberry? Again, this is a very annoying problem and really needs to be fixed.
I hope someone in the forum can help me wth these issues.
These two problems are

I haven't tried the older version of skype yet. But I did try one thing that worked, it's just not ideal. Basically I set up a new account through skype and then logged in through that account. Everything worked perfectly fine. I could send and receive messages and everything updated like it was supposed to. Altough I obviously had to readd all my contacts and group chats, which was a pain. I logged out of that account and logged back into my original one and it was still having the same problems. I have absolutely no idea why a new account will work fine but my old account won't. But if you want to keep the updated version of skype and don't mind all of the hassle of making a new account, that's one sort of solution.

BIG problems with setup after Archive and Install

It all began when I was preparing a G3 iMac to be used - as a trial - by a Windows user. I wanted to preserve the existing accounts so created a new user. I then forgot the new user password (didn't write it down, did I) and had already set it up to go straight to the login screen on boot. Do you think I could then remember the user name of the original account(this time I knew the password)? I researched and was able to set up a new password for the System Administrator via the Install Disk, and hoped that it would show me the existing user names - it didn't. Despite my best efforts, I was still unable to login. By this stage, the gremlins were really getting to me.
I then decided to do an Archive and Clean Install - after I had repaired disk permissions, disk etc. So far so good, as everything seemed to go OK and the Mac restarted and presented the Welcome screen and I proceeded with setup, like it was a brand new Mac.
After going through the first couple of screens where Apple collects information and moving onto where you can start setting up accounts, the thing just hangs with a blank screen with a grey horizontal line about two-thirds down prior to actually reaching this account setup stage. In spite of every other attempt, I just cannot past this stage. Truly weird.
Next, I upgraded my Firewire Disk from OS9 to OSX using the same installation disks and everything went swimmingly, including the creation of accounts. I have been able to boot normally from this Firewire disk and can see everything on my internal HD. I tried reinstalling the OS again - it still hangs in exactly the same set up stage - "siiigh". I'm now getting seriously ****** off with this process and have more or less decided to clone all the appropriate files from the internal HD, erase the drive and start all over again!
I really don't want to go to this level, and besides, I'm really curious to find out what on earth has gone wrong, and hope forum members can help me out here. I appreciate all responses..... Thanks
PatM

BDAqua wrote:
Seems the HD is bad, but whether it could be fixed by Erasing and using the Zero Data Option, once... only time will tell.
IDE HDs don't last all that long... 4 year old ones make me hold my breath!
Thanks for your reply. If the internal drive is bad, why didn't it show up when I ran Disk Utility repair? I don't think I'll try to resurrect it now if that is a possibility.
I had thought of swapping the drive in the Firewire case into the iMac and vice-versa. I have to say that this G3 has now been replaced by a newish MacBook - chiefly to preserve using Tiger (with Classic support) for all the legacy items that my partner was using on the G3. My partner's 91 y.o. mother will be visiting from Perth (the other side of Oz from us) and loves using the Mac, so I now propose the following:
1. Retrieve critical files (if any left) from the G3 internal HD;
2. Swap the drive as above - mind you, I've never changed an HD in an iMac, but after 20 years of mucking around with all sorts of Macs, fancy my chances here - especially as I come from the READ THE MANUAL school of support.
3. Buy a new IDE HD for the Firewire case, load it up with troubleshooting apps. which would then give me a tool for looking after our other Macs.
Any other suggestions?
PatM

I have a problem with setup page of router netfaster.wlan

hi, the setup page of netfaster.wlan router is no longer displayed properly.it doesn't have the left side options which are needed to set the router.

Hi
If you are still getting this issue, could you please provide a url where we can see this, or a screenshot of the error message.

MBP 5.1 I have a recent problem with airport connectivity. ethernet connection is working fine, but wifi has become extremely slow and bad functioning. signal is received, no problem with the wlan (my husband 's wifi with MBP is perfect) please help

I have a MBP 5.1 with snow leopard 10.6.8. It has been working fine until few days ago, when it started to have different problems:
1) airport is not working well. it is extremely slow, has difficulties in fully loading pages, looses connectivity, It is not browser related, behaves thesame in safari or firefox; it is not the router/wlan; my husband mbp wifi works fine (as it was mine...) and iphone wifi is also working fine. it sees the signal and different networks. , it is also very very slow in opening skype (after that, it is working ok) if I connect via ethernet cable to the same router, everything works perfectly and with the correct speed.could it be a damaged airport card? a software problem/corruption? logic board? (I hope not, the computer is out of apple care now....)
2) after a certain time (more than hours) of use, the trackpad is behaving strangly, increase sensitivity to touch, unwanted selection of folders, files and text or images in web pages when i move the cursor, the cursor jumping all over the places while writing, ecc I have the impression it starts doing that when I use heavily the CPU ( and the temperature goes up). Is this again a problem of the mother/logic board?
I had recently serviced it since it was not booting properly, but except some permissions repaired, they did noit find anything wrong in the hard drive (which I have now substituted with a SSD) or other hardware.
thanks in advance for any help/suggestions
alessandra

I think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
the funny behaviour of the trackpad/cursor still persists. any suggestion???
thanks again

Problem with my WLAN(N93)- need help.

Hello guys,
just recently with WLAN got problem. each time i want to start web browsing this message pop-up.. 'web:already in use'. actually what is the problem?

In my iPhone,at first my photo stream still uploaded but now when I took a photos,it didn't upload to my photo stream.

Problem with setup table fillup

Hi,
I wish to extract data using the business content Data source 2LIS_02_HDR( Purchasing). I have activated the extract structure and all other necessary steps. I have deleted the setup table. When I fillup the set up table I get the error " No Extraction structure is active or no BW is connected". I checked with basis guy regarding the connectivity which is absolutely fine. Please let me know in case you have faced this kind of problem before.
Thanks in advance,
Tapan

hi,
oss note 914268-No extraction structure active or no BW connected
Symptom
Within an instance, you use the NetWeaver components of SAP ERP and BW.
When you execute transactions like to fill rebuild tables in Logistics, the system issues the termination message M2 630:
No extraction structure active or no BW connected
The connection test and the settings for the Myself source system are definitely correctly maintained.
Other terms
OLTP, extractor, data extraction, DataSource, API service, SAPI, RSA2_SERV_BW_CONNECTED, OLI1BW, OLIZBW, OLI3BW, OLI9BW, 2LIS_XX_XXX, M2630, SBIW, LIS, rebuild
Reason and Prerequisites
The problem is caused by a program error.
Prerequisites:
Within an instance, you are using the NetWeaver components of SAP ERP and BW. Thus, potential data loading processes are executed by using the Myself source system connection.
No other BW system is connected for data as a target system.
Cause:
Prior to NetWeaver, you could not operate ERP and BW in one common system. For this reason, the case that Logistics data need to be loaded into the same system for BW functions was not considered. The system as "source system" does not recognize that the system is connected as a "BW system".
Solution
To correct the problem, you need Service API 7.00 Support Package 08 or PI 2004.1 4.6C Support Package 13 in the affected source system. The attached composite SAP note informs you on which software components contain Service API 7.0 and lists the corresponding Support Packages of these components.
Alternatively, implement the attached program corrections.
In the BW system, you only need to implement the correction if the BW system is affected in its role as a source system for itselt (myself connection) or for another BW system.
Caution: Service API is an internal component. Therfore, it is not delivered separately but as a part of other software components: PI, CRM, PI_BASIS and several others. Thus, a composite SAP note is created for each SAPI correction note. This composite note describes which Support Packages of the above mentioned software components contain the SAPI correction. However, the composite SAP note will only be released when the corresponding SAPI Support Packages are released.

Problems with broadcom wlan adapter and wlan-button.

I've got a laptop (HP Compaq 6715S), which has an integrated wlan adapter (broadcom 4311/4312?). A couple of weeks ago the adapter was working ok with ndiswrapper and bcmwl5.inf driver, but it stopped working recently probably after ndiswrapper and/or kernel upgrade. Loading the ndiswrapper module from rc.conf made the whole system kernel panic (IRQ problem?) until I added:
acpi=noirq
to the kernel boot parameters. Now this error doesn't occur every time I load ndiswrapper, but the problem still exists. BCM43xx driver doesn't work either. I'm using the 64-bit arch.
in my rc.conf I have:
MOD_AUTOLOAD="yes"
MOD_BLACKLIST=(pcspkr joydev bcm43xx bluetooth hci_usb pcmcia yenta_socket pcmcia_core)
MODULES=(fglrx ieee80211 ieee80211softmac ieee80211_crypt ieee80211_crypt_wep ieee80211_crypt_tkip
ieee80211_crypt_ccmp powernow-k8 k8temp thermal fan battery button cpufreq_powersave cpufreq_ondemand
freq_table)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
DAEMONS=(syslog-ng dbus laptop-mode acpid cpufreq @alsa network wicd gdm)
lspci:
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
00:04.0 PCI bridge: ATI Technologies Inc Unknown device 7914
00:05.0 PCI bridge: ATI Technologies Inc Unknown device 7915
00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2)
00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA
00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0)
00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1)
00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2)
00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3)
00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4)
00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI)
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14)
00:14.1 IDE interface: ATI Technologies Inc SB600 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series]
02:04.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b6)
10:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02)
30:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 02)
dmesg |grep ndis (after error)
ndiswrapper version 1.49 loaded (smp=yes, preempt=yes)
ndiswrapper (link_pe_images:576): fixing KI_USER_SHARED_DATA address in the driver
ndiswrapper: driver bcmwl5 (Broadcom,10/12/2006, 4.100.15.5) loaded
Modules linked in: ndiswrapper snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss
snd_mixer_oss container tsdev rtc_cmos rtc_core rtc_lib serio_raw evdev psmouse i2c_piix4 i2c_core ehci_hcd
ohci_hcd shpchp pci_hotplug cpufreq_ondemand cpufreq_powersave k8temp ieee80211_crypt_ccmp
ieee80211_crypt_tkip ieee80211_crypt_wep ieee80211softmac ieee80211 ieee80211_crypt fglrx(P) usbcore tg3
snd_hda_intel snd_pcm snd_timer snd_page_alloc snd_hwdep snd soundcore ac button battery fan sbs thermal
video output powernow_k8 freq_table processor ext3 jbd mbcache sd_mod sr_mod cdrom sg ahci ata_generic
pata_atiixp libata
[<ffffffff88405e77>] :ndiswrapper:win2lin2+0xe/0x11
[<ffffffff883fa330>] :ndiswrapper:IoAcquireCancelSpinLock+0x10/0x20
[<ffffffff883fae47>] :ndiswrapper:IofCompleteRequest+0x87/0x180
[<ffffffff883fc4d2>] :ndiswrapper:pdoDispatchPnp+0x52/0x490
[<ffffffff88400c08>] :ndiswrapper:mp_init+0xa8/0x1e0
[<ffffffff883fa5f4>] :ndiswrapper:IofCallDriver+0x34/0xc0
[<ffffffff883fb930>] :ndiswrapper:IoSyncForwardIrp+0x90/0xd0
[<ffffffff88400e1b>] :ndiswrapper:NdisDispatchPnp+0xdb/0xee0
[<ffffffff883fb1db>] :ndiswrapper:IoInitializeIrp+0x3b/0x70
[<ffffffff88405e77>] :ndiswrapper:win2lin2+0xe/0x11
[<ffffffff883fa5f4>] :ndiswrapper:IofCallDriver+0x34/0xc0
[<ffffffff883fa61f>] :ndiswrapper:IofCallDriver+0x5f/0xc0
[<ffffffff883fa330>] :ndiswrapper:IoAcquireCancelSpinLock+0x10/0x20
[<ffffffff883fa5f4>] :ndiswrapper:IofCallDriver+0x34/0xc0
[<ffffffff883fb6bf>] :ndiswrapper:IoBuildSynchronousFsdRequest+0x2f/0x50
[<ffffffff883fc9fc>] :ndiswrapper:IoSendIrpTopDev+0xac/0x100
[<ffffffff883fccff>] :ndiswrapper:pnp_start_device+0x4f/0xa0
[<ffffffff883fcf6f>] :ndiswrapper:wrap_pnp_start_device+0x21f/0x260
[<ffffffff883fd000>] :ndiswrapper:wrap_pnp_start_pci_device+0x50/0x60
[<ffffffff883ef04c>] :ndiswrapper:loader_init+0x13c/0x260
[<ffffffff883700b7>] :ndiswrapper:wrapper_init+0xb7/0xc3
The other problem that I have is the wlan-button: The wlan adapter isn't always turned on at boot and I have found no way to turn it on from linux. It can be turned on by booting to windows or resetting the bios to defaults, but it is not very nice. I've noticed that pressing the wlan button adds one usb device:
Bus 001 Device 003: ID 03f0:171d Hewlett-Packard
Is there a way to fix these problems?

lenni wrote:
When I used to use ndiswrapper, just downloading one of the generic INF files didn't do the trick for me. I had to go to my manufacturer's homepage and download it there extract the drivers from the exe and use them in order to get my card work reliably.
Also, have you used a 64 bit driver? This guy reckons you need it:
http://www.linuxquestions.org/questions … ost2952703
I guess I solved it. I have been using the 64-bit driver, but have tried the 32-bit driver from hp diver site too. For some reason ndiswrapper seems to install a driver named "ndiswrapper" with this 32-bit driver, which is why it didn't work. So my solution was:
1) Get the 32-bit driver from hp.com
2) rmmod ndiswrapper
3) remove all installed ndiswrapper drivers: ndiswrapper -r <drivername>
4) installed the 32-bit driver: ndiswrapper -i bcmwl5.inf
5) ndiswrapper -l gave me:
bcmwl5 : driver installed
device (14E4:4312) present (alternate driver: bcm43xx)
ndiswrapper : invalid driver!
6) Got rid of the weird ndiswrapper driver inside ndiswrapper: ndiswrapper -r ndiswrapper
7) modprobe ndiswrapper
Rebooted a couple of times and it seems to work ok.
How about the wlan-button problem?

80 Problem with setup

I downloaded iTunes and connected my 80gb iPod classic, and now I'm seeing a page entitled iPod Software License Agreement. I read the agreement and clicked a checked box saying that I agree to it, but I can't scroll right to continue the setup process. Anybody have this problem or know how to fix it?
Message was edited by: dafisch
Message was edited by: dafisch

Ok - this is more of a rant than anything useful so beware! It seems that Apple has taken a page or two from the banks, insurance and health care providers which is to stick your customers at every opportunity.
It's a day after christmas and, surprise!, my friend can't use the new $350 ipod classic I got her on her OS 10.3.x machine. So let me state the problem just to be clear and in case I've gotten anything wrong you all can correct me:
The company that prides itself on designing products for the 'rest of us' (read: idiots that don't know how to set the clock on a microwave, much less use a computer) has decided that what is essentially a portable hard drive needs an OS upgrade to function correctly. I'm sorry is there something in that split screen display on the new ipods that requires 10.4 to run properly?
Wait, wait! I'm sorry, silly me - it's clearly buried on the website that >10.4 is required to operate a, ahem, 'classic' ipod. It probably says that on the box too (in equally small type). It really isn't too much to ask to take a moment out of the holiday pushing and shoving and spend some time squinting at 8pt type (grey on black!) and try and figure out if it your walkman will work with someone else's computer. The miracles of christmas! You know - I'll bet if I hook up my old tape walkman to the line out jack on her laptop that would work!
So decisions, decisions. Do I scramble around and source a copy of Tiger (can you find that for power pc anymore) or just buy a new laptop? Please help!
Remember folks:
1 - Always get a referral
2 - No more than 3oz of any liquid and recheck your duty free purchases
3 - Pay off that balance transfer before the rates reset
4 - A portable, personal audio device is not necessarily portable in every sense of the word!
Thanks for listening.

N86 8MP problem with setup WLAN notifications

Similar Messages

Maybe you are looking for