Need help setting up Airport Express A1084 in Windows 7 via Netgear WNDR4500 wireless router
Hello All. I bought a used Airport Express A1084 off the net. Never had one before. My intention is to remotely control (via my iPhone using Apples Remote app or possibly XBMC) a "pc with music" and stream thru the AE connected to a boombox. I want to be able to take AE and boombox to the front yard, back yard, garage, or wherever my Netgear WNDR4500 will reach.
So far I have hit the reset on the AE and while holding, plugged it in to power (still holding) until the green light blinked. I let it go. Waited for it to complete booting (slow blinking yellow/amber light). The AE did not show up in Airport Utility ver 5.6.1. I uninstalled that version and installed older Airport Utility ver 5.4.2. Same results. I power cycled the router, turned off the Norton 365 firewall, and still get nothing. At one point though, I walked away for a while (an hour or so), came back and saw the AE listed in the left window pane of Airport Utility. I thought maybe I just didn't wait long enough so I clicked Manual Setup and it started to read the AE but Errored 10057. I tried again and got same error. I refreshed and the AE was gone.
Can someone tell me how to correct this so I can confirm I didn't buy a "brick"?
Thanks in advance,
Tom
Just so you are aware, the A1084 AirPort Express is a 802.11b/g wireless router that can only operate on the 2.4 GHz band. Regardless, it can be configured to join the wireless network provided by the Netgear as long as that network is configured to be backwards compatible with 802.11g clients. However, in the long run for performance, you do NOT want any non-"n" wireless clients connecting to your Netgear's network.
The 5.6.1 version of the AirPort Utility for Windows does not support the non-"n" version of the AirPort base stations. You would need to use an earlier version that will still run on Windows 7.
One thing to try would be to temporarily connect the Express directly to your PC using an Ethernet cable, and then, try accessing it with the AirPort Utility. If you are still unable to do so, you may have gotten yourself a defective unit.
Similar Messages
-
How to set up Airport Express to extend Buffalo WHR HP 54g wireless router
Contrary to what official Apple policy is, it is possible to use Airport Express as a remote repeater using a Buffalo router.
I sent hours setting up this network and wish to share what I learned
I only wanted to use the Airport Express as a repeater to distribute the internet to the far reaches of the house--no iTunes, no Printer, and I did not bother setting security. If you want to add any of those features please make sure that the basic setup is working as described below. I have no idea how to successfully set up these features. My advice is to search the internet for guidance.
Anyway: how to set up the Buffalo wireless access router to work with Airport Express
Setting up the Buffalo:
From the routers home page of 192.168.11.1, hit the "advanced" box at the top
1. Go the "Wireless config" "basic" item. Give name to your network (spaces are allowed), lets call it "WIRENAME" and select wireless channel 1 or 6 or 11. These channels have the least interference and will tend to work when the others do not.
2. Go the the "repeater" item under Wireless config. . " Enable" repeater/bridge (WDS). Next register the MAC address of the Airport Express. Record both the LAN and Wireless MAC addresses.
That is about it. Your Buffalo system Info page should look like this
Model
WHR-HP-G54 Ver.1.40 (1.0.37-1.08-1.04)
AirStation Name AP001D73DEB2D6 Operational Mode Router Mode WAN
DHCP
Connection Status
Communicating
Operation
IP Address
myinfo
Subnet Mask
255.255.255.248
Default Gateway
my info(Via DHCP)
DNS1(Primary)
my info (Via DHCP)
DNS2(Secondary)
my info (Via DHCP)
Host Name
my info (Manual Setup)
Domain Name
earthlink.net (Via DHCP)
MTU Size
1500
DHCP Server Address
10.108.48.1
Lease Acquired Time
2006/01/04 12:03:15
Lease Period
2006/01/05 12:03:15
Wired Link
100Base-TX (Full-duplex)
MAC Address
00:1D:73:xx:xx:xx
LAN
IP Address
192.168.11.1
Subnet Mask
255.255.255.0
DHCP Server
Enabled
MAC Address
your address recorded in the repeater tab
Wireless(802.11g)
Wireless Status
Enabled
SSID
WIRENAME
Encryption Mode
Not Configured
Wireless Channel
11Channel (Manual)
125* High Speed Mode
Disabled
MAC Address
your address recorded in the repeater tab
For the Airport express: here is a summary of what the settings are: Start Airport Express Utility and when it comes up
Select "Manual" setup
On the Base station tab: Give Airport Express a name, any name and any password. Do not select the box: Allow setup over the internet with Bonjour
On the wireless tab: Wireless mode: Participate in a WDS network
Network name: the name you gave in the Buffalo router: EG: WIRENAME
Radio mode: 802.11n(802.11b/g compatible)
Channel : the same as you set in the Buffalo
Wireless security: None
WDS tab: WDS mode: WDS remote
Check: allow wireless clients
WDS main: the MAC address of the wireless (not LAN) side of the Buffalo router
Access control tab: MAC address access control: Not enabled
At the top of the control box , click on the Internet icon
Internet connection: Connection sharing: Off (Bridge Mode)
TCP/IP: Configure iPV4 : Using DHCP
I put in the address of the DNS servers listed on the Buffalo System info page above.
At the top of the control box Music Icon: I did not enable AirTunes
Printer icon: did not set this up
Advanced icon: leave every thing alone
That is it. Just do everything as above and your Airport Express will act as a repeater. (And save yourself a couple of days struggle.)
PhilMany thanks for the info.
In case you were not aware,the following list of Apple WDS compatible devices has appeared on numerous sites and in numerous Internet links and articles regarding this subject:
3com OfficeConnect ADSL Wireless 11g Firewall Router model 3crwdr100a-72 but ONLY with NO encryption
Belkin F5D7230-4 and F5D7231
BT Voyager 2091 or 2100
Buffalo WGR-G54
Linksys WRT54G or WRT54GS (though v4)
Netgear WGR614 v6 -
I need help setting up airport express to play my Itunes music to my stereo
Hello I am hoping someone can help me as I am at a total loss here. I have had an airport express for a few years and would stream my music to my stereo without any problems. A few months ago it would cut out every now and again but soon it got so bad it was unlistenable. I reset it many times but to no avail.
Now when I try to reset it by opening the airport utility it scans but does not find the airport express.
I bought a pluglink ethernet adapter and connected it to the Airport Express hoping I can run it through that but when I open up the airport utility it scans but still will not recognize the airport express.
Is there some way to set this up .
I have an IMac which has the latest operating system.
Sincerely grateful for any help in this matter Paul K.Hello blakemj. Welcome to the Apple Discussions!
For your described network configuration, you will want to reconfigure your 802.11n AirPort Express Base Station (AXn) as a "wireless client" to the Buffalo wireless router.
Here's how ...
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
(Note: As a third option, you can temporarily connect the AXn directly to an available LAN port on your Buffalo wireless router during setup, and then, place it at the desired location when complete.)
AirPort > Base Station
o Base Station Name: <rename or leave default>
o Base Station Password: <enter desired password>
o Verify Password: <re-enter desired password>
o Remember this password in my keychain: (optional)
o Set time automatically: (unchecked)
AirPort > Wireless
o Wireless Mode: Join a wireless network
o Network Name: <existing Buffalo's wireless network>
o Wireless Security: <select the encryption type of the existing wireless network>
o Wireless Password: <enter the existing wireless network password>
o Verify Password: <re-enter the existing wireless network password>
Music
o Enable AirTunes (checked)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked) -
Need help setting up airport express as bridge (Any help is appreciated)
Hello so before my wifi was switched I was able to use my 802.11g airport express as a wifi card for the xbox 360. I then decided to upgrade my main base station from an 802.11g base station to and airport extreme 802.11n. My problem is that my airport express cant extend the airport extreme network to my xbox anymore because they are different 802.11 versions. So can anyone help me configure this so I can get this back? Any help is appreciated.
My Current Setup:
Internet => Airport Extreme 802.11n => Wireless => Airport Express 802.11g (to extend network for xbox)=> Ethernet => Xbox 360
Thanks!As I said, WDS is a nightmare for most users. Apple hides the settings from users to discourage use of WDS.
I do not recommend that you do this, but have a feeling that you will do this anyway.
I will not be able to help you sort out WDS problems.
On AirPort Utility 5.6, click Manual Setup
Click the Wireless tab below the icons
Hold down the option key on your Mac while you click on the Wireless Mode selection box and the WDS settings will appear
Apple's instructions for WDS are here:
http://support.apple.com/kb/HT4262
Hope this helps. Good luck. -
I need to know how to connect to internet using the netgear n150 wireless router
I recently signed up with comcast internet. They supplied a NETGEAR N150 wireless router. After following instructions that came with router, I still cannot use the router to connect to the internet. The computer has to be connected directly to the modem for internet access. HELP!!!!
Here are some of the recommended setting from Apple. Maybe that will help.
http://support.apple.com/kb/HT4199
Regards,
Captfred -
Need help setting up older Express.
Heres what I have and what I want to do:
I have a 2005 Power Mac G5 (10.5.8) without built in wifi, I want to connect it to my network via Express in bridge mode(?). I cannot hard wire because of its location but it is well within wifi range.
I get thru the set up and have a steady green light and Airport utility says its connected to the internet but it seems that its not sharing thru the ethernet port.
After set up, the express reboots and cannot be found by Airport utility, I have to reset to try anything different.
My main router is not an Apple base station.
I can't seem to install (it fails) Airport utility 5.6 on my Macbook (10.7.5) to try a different set up. And I can't seem to find any solutions on the web for my situation. I have also tried set up via iPad and iPhone - no luck.
Thoughts, Suggestions, Solutions?
Thanks!I get thru the set up and have a steady green light and Airport utility says its connected to the internet but it seems that its not sharing thru the ethernet port.
The older A1084 and A1088 versions of the AirPort Express do not have the ability to join a wireless network and provide an Ethernet signal at the Ethernet port, so if you have one of these models, that would explain the difficulties.
Look on the side of the AirPort Express to locate the model number, which may be difficult to see with gray lettering on a white background.
The more recent A1264 and current A1392 version of the Express are capable of doing what you want. -
I need help configuring the Airport express from a PC
Hi there!
I want to configure the airport express from a PC. It runs okay but the connection is open (anyone can browse on my connection)
In a PDF that I found on Apples web site, it says go to
Start-> All programs-> Airport express setup assistant, but there are no programs named Airport on my PC!
Do I have to download a utility for this purpose?
FredrikIf all you want to do is add wireless security to an already configured Express, you'll probably want to use the Airport Admin Utility. You should be able to install it by installing this package:
http://www.apple.com/support/downloads/airport42forwindows.html
If the PC isn't running at least Windows XP, I think you're out of luck. -
Airport Express won't join via ethernet, only wirelessly
I have a Time Capsule, two AEs wired and another AE operating wirelessly in my home network. Problem is I can't get the wired ones to join as wired ones. They'll only connect to the network wirelessly. So I can have a network completely wireless but I'd prefer the speed of the two AEs wired. I've been through many attempts, set-ups and versions with the AEs trying to resolve this. A potential big wrinkle is that the router is connected to two different switches that handle the various ethernet cables serving many rooms in the house so I'm thinking that may be the problem. Is that likely or am I missing something?
Well, the way to do this would be to go ahead and setup both AirPort Express devices one at a time near the Time Capsule...and connect them directly to the Time Capsule using Ethernet.
Get them working correctly that way first.
Then, move them to the backside of the Ethernet backbone for the network. If the Express devices don't work there....then you have an Ethernet switch problem, an Ethernet cabling problem, or possibly both. Tedious troubleshooting will be required.
In situations like you describe, 90% of the time the issue boils down to an improperly installed Ethernet plug, a broken wire somewhere, or a bad port on a switch. That is not to say that this is the issue, but it is the area to place your bets.
We did not get any details about what generation model the Express devices might be, or what type of operating system you are using on the Mac or PC to configure the Express devices. We'll need basic information like that if you desire additional help. -
Can you use airport extreme as a bridge to netgear wdnr4500 wireless router
can you use airport extreme as a bridge with a netgear wndr4500 router.I need to extend my wireless connections to the other side of the house
can you use airport extreme as a bridge with a netgear wndr4500 router.
This is extremely unlikely. The AirPort Extreme can provide this function with other Apple routers, but as far we know, it is not compatible with products from other manufacturers for this purpose.
Suggest that you use a Netgear product for the best chance of compatibility. -
Help a newbie: Windows XP, Netgear WGT624 Wireless router & AE
I just installed a Netgear wireless router and am trying to setup the AE to play music on my home stereo. For some reason when I connect the AE to the outlet close to my living room home stereo, the Airport setup Assistant doesn't recognize my base station. I don't know what to do. I know my wireless router is setup correctly, but I can't figure out the AE setup process. Please help!
Do you have any wireless encryption activated on your Netgear Wireless Router? If so, you should disable it, then your wireless router should be able to connect to your AE. Then configure your AE to match your security settings of your wireless router, then finally re-activate the wireless security on your router.
(Make sure you select "Join an exisiting wireless network" when configuring the AE, enter the data carefully to match the security information in your router.
Once you re-activate your wireless security in your router and restart the AE, it should join your network. -
Need help setting up airport on G3 iMac
Hi All,
Similar issue with an old iMac I bought for my girlfriend on ebay.
Just inserted the wireless card I bought for it. The router is a british (BT Home Hub3) wireless N, the machine is an iMac G3 400Mhz running Panther, I'm guessing the same issue applies to set the router to WEP/WPA as currently I can't see it listed at all so cannot connect?
Many thanks.
Phil
<Edited By Host>For 10.3 you will be limitted to what browswers you can try. The newest version of Firefox for 10.3 will not surf the web that well. You need to be running Tiger to get a decent port of Firefox... TenFourFox.
I recommend one of these browser for 10.3.
Opera
http://www.opera.com/browser/download/requirements/
http://www.opera.com/download/
OmniWeb 5.11, which, I believe is built on the same framework as Safari 5,
iCab - The Taxi for the Internet
http://www.icab.de/
Some folks have gotten Tiger cds out of Apple. ( some related to what you say. )
AppleCare Support Phone Number: 1-800-275-2273
open 6am to 6pm Pacific Time
Apple Phone Sales 1-800-692-7753
International Technical Support Numbers
http://www.apple.com/support/contact/phone_contacts.html
Robert -
Need help setting up auto resizing of GTK window
Hi,
I have a GTK image in a scrolled window in a top window and I need to find out how to arrange for the main window to accomodate size changes of the image. Resizing the scrolled window causes the top window to resize but resizing the image just makes the scrolled window to accomodate the change without a change in the top window size.
Any suggstions on how to do this while maintaining an automatic policy for the scrolled window?
My thanks in advance.just call gtk_widget_set_size_request on the window when the image size changes
-
Can airport express support WDS thru a linksys wag200g wireless router
just got the above router and have to extend the range of my network so it can reach my mac mini. am trying to use a/ex as a remote but not having any luck. i know alot of routers do not support WDS but was told this one did. can anyone help? am just about ready to throw it through a window!
Hi again kenkarno,
So the whole idea of WDS (Wireless Distribution System) is to enable you to use multiple devices (i.e. Wireless Routers) on the same network.
For example if you set up a wireless network called "kenkarno" but your original router wasn't powerful to cover the desired area, you could add further routers to the same "kenkarno" network as opposed to creating a multitude of networks for each router. The obvious advantage is that if you're out of range of one router you're in range of another without having to switch networks.
At the moment WDS is very proprietary (hence my first post) so it is common when trying to set up a WDS composed of different brand routers, you may not get them to talk to one another due to incompatibilities in their software.
In your case, it could be that your Actiontec router will not be able to form part of a WDS with your AE so your suggestion of using ethernet between the Actiontec and the AE could be the way to go here (although you'd have two separate networks). If you went for a second AE you could create a WDS between this and your existing one which may make life a little easier.
Hope it works out -
I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?
Before I bought it I did the same question at the Apple Store, and they told me "You can extend your existing Wi-Fi Signal with Airport Express wireless...
You cannot extend wireless from any brand except another apple router.. the store might have assumed you were using an apple main router. Most people who buy express buy them to extend an extreme or time capsule.
You are correct .. in the setup documents it does say 5.6.1 is adequate to do the setup.. my bad.. !! -
How can I find out which version of Airport Utility is needed for my Airport Express A1084????
I have this issue, too. The problem with the advice from Saito_Chickara is that Mavericks (I'm on 10.9.2) does not allow you to run AirPort Utility 5.x. So for those of us on Mavericks, what can we do? I have yet to find a solution. This is really frustrating.
Maybe you are looking for
-
Creative Cloud with Business Catalyst/Websites
I subscribed to a standard Creative Cloud membership yesterday.... On the Creative Cloud web page sidebar, there's a message saying 'Full Creative Cloud Membership comes with hosting for up to 5 sites....LEARN MORE >> That goes to a page which says "
-
Is the video iPod compatible with Windows Vista?
I need to get a new computer and I was wondering if my video ipod will work on a computer that has windows vista. Any help would be appreciated.
-
Adobe In Design CC 2014 won't install on a PC but it will on another.
I have a user who I'm trying to deploy a new laptop for. I am installing Adobe In Design CC 2014 but early in the install it just suddenly quits. I can install the software on my own PC with no problem both are running Windows 7 64 bit. Any ideas?
-
Hell All, Can anyone tell me whether the Digitial or scanned signature is allowed in India for the purchase order print out which has been created in SAP. If yes then could u please tell me which company is having such kind of practice. Thanks in adv
-
Can't start OAS-4.0.8.1 on RH 6.2
During startup of OAS i recieve error message: $owsctl start Please wait while the command is being processed on host mhs_3 ... Starting ORB process... waiting for ORB to be ready... The command completed successfully on host mhs_3. OWS-08820: Unable