Need help with Macbook reinstall on new hard drive!

Hey Everyone!
So my old MacBook A1181 was damaged a bit in a fall from a shelf. I followed all the directions on PowermacMedic (bless them!) and put in a new LCD screen, as the old one was cracked. Cleaned a lot of cat hair out of machine while I was at it.
I also replaced the hard drive with a new one, because the old one had a question-mark-over-a-folder icon. I'm very proud of myself, as there are only four screws left over. LOL!
So now it's time to reinstall the Tiger system. The optical drive is not working, so I researched on how to make an external hard drive bootable, put the Tiger Installation on that and connected it via FireWire to the old MacBook.
Turned it on and pressed Alt/Option at the same time. Great...up popped the Tiger Installation information. I've clicked on Install, etc., and am at the point where I need to choose a destination drive. Except there is none listed.
I've gone to Disk Utility, and I can see the new drive there, but just the icon as the major piece of hardware...there's no sub-icon for it underneath, like there usually is.
So, any ideas on how to make my new hard drive readable so I can choose it from the Tiger Installer?
Any help would be much appreciated. I've never even attempted to do something like this before, and I don't want to give up just yet!
Jenny

Do this:
Drive Preparation
1.  Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button.  When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
After the formatting has completed quit DU and return to the installer. Install OS X.

Similar Messages

  • M7 -j010dx: need help w/recovery Windows 8 new hard drive

    installed new hard drive installed (old one hard disk (3f0) error and confirmed dead by Geek Squad). I have recovery discs from HP. how to proceed from here?  Tried the "put App and Driver recovery disc in and turn on" route. no go and same "Boot device not found. Please install operating system on your hard disk.  hard disk (3f0)." error comes up.
    Is there more to the process than this? I'm not getting what's going on.
    Thanks in advance...
    This question was solved.
    View Solution.

    correct. kicked it right back out.
    still moving positive...

  • Need help with iMovie storage on external Hard drive

    Is there any external HD that is fast enough to run iMovie? I just bought an 80gig ext. hard drive trying to solve that nasty memory problem that iMovie HD has... Well iMovie will not run because it's not fast enough, and the video clips play slow and choppy.. My question is does anyone know of a brand type or speed of ext. hd that is fast enough.. HELP!!! I need to finish this video pronto!
    Thanks
    ps.. the HD i bought was an iomega 80gig HD with usb 2 and 7200 rpm

    Eric, for a few dollars/Euros more (..or whatever your currency is..) you could buy a FireWire enclosure ..that's just a box with a socket or two on the back. It's not a drive, but just a box to put the disc drive inside, and it's complete with FireWire connections.
    Then unscrew the Iomega 80GB USB box, remove the 7200rpm 80GB disc drive, and insert it into the FireWire box, and connect up the multi-pin connector and power connector between the FW box and the hard drive. Connecting the drive is pretty simple. Look at "Mounting the drive into the bay", about halfway down this page.
    Hey Presto! ..You've now got a working 80GB 7200rpm drive ..plenty fast enough for iMovie.. which can be connected to your iMac via FireWire!
    Your disc drive is fast enough ..it's just your USB connection which is too slow; so just change the way that your drive is attached to the Mac, so that it uses FireWire.
    Suitable boxes are this kind of thing.
    It's simple: I have half a dozen assorted drives I've slotted into new bare-bones 'enclosures', and they all work fine by just plugging the enclosure (box) into a Mac FireWire port.
    Quick 'n' simple, and cheap!
    NOTE: Open up your Iomega box first, so that you can check what size of drive is inside, and thus what size of FireWire enclosure you need. A small 2.5" drive will certainly fit into a 5" enclosure, but a 5" drive obviously won't fit in a 2.5" enclosure! Though something like a WiebeTech DriveDock ..or the bigger and pricier ComboDock.. are open-ended, so they'll take any physical size of drive.

  • Need help to partition and format new hard drive for T400

    The HDD failed in my T400. I bought a new 1TB HDD and fitted it. The diagnostic software in the BIOS did a read and controller test (Passed). When I put the Windows XP disk in the CD reader, the setup started - then stalled at the "Windows setup" page. I thought the hard drive had a write problem but apparently it must be partitioned and formatted first, before Widows setup can commence. The thing is that I can't get to the option where Windows formats the drive. In old computers, there was always a partitioning option in the BIOS setup but in my T400, there doesn't appear to be any such option. The computer has 4GB RAM, the actual model is 2767-RV8.
    Does anyone have any suggestions how to get this up and running?
    One other question is - (assuming I can get the thing working) - Is there somewhere I can load the operating system on part of the hard drive where it can act as a fall back in case the operating system gets corrupted? - i.e. something that can't get attacked by malicious software?
    Thanks in advance for any assistance.
    Ian

    Hi irivlin,
    If you are trying to clean install XP, then you have to do following setting in BIOS first:
    Press F1 to BIOS, Config -> Serial ATA (SATA) -> change to "Compatibility"
    You can change XP partition only if you are doing clean installation, otherwise you have to use 3rd party to do it.
    For backup part, there are lots of choices in the market. You might consider using XP own backup function. Lenovo got a program called Rescue and Recovery can also do backup as well.
    How to use the Backup utility to back up files and folders in Windows XP Home Edition
    http://support.microsoft.com/kb/320820/en-us
    Rescue and Recovery® 4.23 by Lenovo
    http://support.lenovo.com/en_US/product-and-parts/​detail.page?&LegacyDocID=MIGR-76225
    Fred
    T61 + X201i

  • Need Help With Backup To Pc After Hard Drive Format

    Hi All,
    I reformatted my pc which meant i had to reinstall itunes.
    Inserted my iphone after i reinstalled itunes and none of my apps where saved in itunes.
    Clicked sync and it did not backup any apps to itunes.
    After alot of mucking around it eventually took all my apps off my iphone and then i mhad to use my wifes iphone to get the apps back.
    Is there a simple guide to how this is done after reformatting a pc?
    Cheers

    The simplest way really is to restore your PC from a backup. A fresh install is a fresh install. When you connected your iPhone to the fresh install of iTunes, did it not ask to transfer the apps to your PC?

  • Need help saving iPhoto library from damaged hard drive

    Trying to help my wife, she has the following:
    MacBook Pro running OS X Lion version 10.7.3
    iPhoto 11 version 9.2.2
    Her hard drive failed last week and she had a ton of photos on it, of course not backed up.
    We took her machine to the local Apple Store, they confirmed they couldn't recover the data and they installed a new hard drive in the MacBook.  We took the old hard drive to my local PC supplier who's very clever, he worked on the hard drive and was able to copy all my wife's documents to another storage device.....but, he couldn't copy the iPhoto library and is requesting some help.....he doesn't know much about Macs, nor how iPhoto works.
    I've read a lot of the posts on this forum and am learning about how the iPhoto library works....and how it requires a Mac based back up hard drive in order to copy it.  Okay, here are my questions:
    1.  My PC troubleshooting guy can see the iPhoto library icon on the damaged hard drive, he says its a huge file.  It appears we would need to supply him with a Mac formated back up hard drive, then he could just move that iPhoto library icon (which contains all photos) to the new back up drive.  Is this correct?
    2.  Once we have this old iPhoto library on the new back up hard drive, we could bring it home of course, but then I need to get it into the new hard drive on my wife's MacBook Pro.  I'm assuming I can plug this back up drive into my wife's machine, then import the old library into her machine.  How do I do this properly?
    3.  If I bring the old library into the new MacBook Pro hard drive, will it erase the existing iPhoto library on her new hard MacBook Pro hard drive, or will it combine them somehow?  She has added of course some pics to the new iPhoto library already, but if we have to delete them it won't kill us.  The old stuff that got recovered from the damaged drive is more important.
    Thanks ahead.....now to the experts?

    Thanks Terence.....
    regarding this point:
    3. use the paid version ($20) of  iPhoto Library Manager to merge the Libraries. that way you won't lose anything.
    I have another access to her new photos, whereby I could reload them onto her MacBook if we lose the new library.....so I'll save the $20 and just reload them.....two more questions:
    1.  So, if I drag the iPhoto library folder from the new back up hard drive to the Pictures Folder in Finder, will that overwrite the existing library folder on her MacBook?
    2.  After I drag this folder into finder, will iPhoto recognize everything?  I assume yes....just checking.
    thanks ahead!

  • I just replaced the hard drive on my macbook pro, reformatted new hard drive and copied over a backup from time machine now I have a kernel panic message (you must restart) - what do I do now?

    i just replaced the hard drive on my macbook pro, reformatted new hard drive, installed a back up from time machine and now have kernel panic ( you must restart your computer) what do I need to do?

    If you're able to boot, launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
    Select the most recent panic log under System Diagnostic Reports. Post the contents – the text, please, not a screenshot. For privacy’s sake, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post "shutdownStall" or "hang" reports.
    If you can't boot in the usual way, try a safe boot. The instructions provided by Apple are as follows:
    Be sure your Mac is shut down.
    Press the power button.
    Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
    Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
    During startup, you’ll see a progress bar, and then the login screen, which appears even if you normally log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Safe mode is slower than normal, and some things won’t work at all.

  • I had Iphoto on my computer when i bought it and now had to reinstall a new hard drive do i have to buy it again?

    I had Iphoto on my computer when i bought it and now had to reinstall a new hard drive do i have to buy it again?

    reinstall from the original source
    Could be
    1 - the restore disks that came with the computer
    or
    2 - the iLife DVD that you purchased
    or
    3 - the app store - log in under the Apple id used to purchase the software or to set up the computer - look under purchases - you might have to unhide or accept the Application first
    LN

  • I reinstalled a new Hard Drive but cannot get the DVD tray to open to install the Mac OS?  How do I open the Tray?

    I reinstall a new Hard drive.  But I cannot open the DVD tray to install the OS?  All I get the the ? in the folder when the computer turns on?

    Hi copa1226:
    Sometimes the best solutions are the manual ones.  There is a mechanical fail safe built in to these devices,  I have had to use this method several times myself, so ....
    .....   Try this:
    1) Power off your mac pro.
    2) With your finger, pull down the metal bezel on the affected drive.
    3) You should now see the front plastic bezel on the affected drive, it is usually black or grey.
    4) Look for a small pinhole somewhere on the front. It will have a very small diameter, about 0.5mm.
    5) Yes it's there, all cd/dvd drives have one!   Note: a small flashlight comes in handy here.
    6) Straighten out a standard paperclip for about 2 -3 inches.
    7) Insert the paperclip in the small hole and push, you will have some resistance, and then the drive tray will slowly push out about 0.5 inches or more.
    8) Grab the tray and pull it out !!
    9) You are done!
    10) If you do this gently you won't hurt the drive. Boot up and the tray should automatically slide back in. You are good to go.

  • Upgrading hard drive... need help on how to prepare current CS6 for reinstall on new hard drive

    I'm about to upgrade my hard drive to a larger one and will need to reinstall my CS6 Web/Design Suite... I've seen many people having issues with activation and licensing after they reformat their computers or buy a new one and try to install the programs on the new "system". How should I go about preparing my Adobe software on the current hard drive so I won't have any issues resintalling on the new hard drive? I will be installing CS6 Student/Teacher version on Windows 7 Pro 64-bit...
    Thanks for the help!

    Thanks!
    I wondered if that was all I needed, but when I built my new system and installed PS CS4 I kept getting errors. So, I went back to the old system and deactivated it and still got errors. Uninstalled it deactivated and still got errors on the new system. When I talked to Adobe they just kept telling me the key was invalid (even though I had been running that same program and key for the last 4 years without problems lol) and it was not a burnt copy or pirated. I had the orginal box with the original DVD case and serial number on the case... A friend of mine had upgraded their rig and went to a Suite so he gave me his CS4. But, needless to say (as it is said all over these forums apparently) Adobe was of no help at all so I had to buy a new version. I'm not looking to go through all of that BS again, haha.
    So as long as I deactivate the Suite (or do I need to deactivate each program separately?) I should be able to reformat (or upgrade hard drives) and reinstall CS6 as many times as I want? (I usually do a reformat like once a year to keep my computers clean and free of junk that may have been downloaded by other household members...)

  • I need help in restoring data recovered from hard drive crash to new hard drive

    I have the data that was recovered by a recovery service (long story) from my wife's hard drive after it crashed, which is now stored on my computer. There are two user data sets that have been recovered, one for each of us. I need to put each on my wife's computer with its new hard drive, which now has OSX 10.10.? (Yosemite) on it.
    My wife's computer was running OSX 10.7 (Lion) when the hard drive failed and my computer is still running OSX 10.6.8 (Snow Leopard).
    I was told that I should use the Data Transfer Utility (starting my computer up while holding the "T" key), but I have forgotten what I have to do when I start up her computer. Are there any operating system compatibility problems that are sensitive to this process?

    That is a Microsoft Windows question??  You should probably ask this question on Microsoft's Forums.  BTW there is no "Windows 9".  Only Windows 7, Windows 8 and apparently MS is skipping the number 9 in favor of 10.

  • What do I need to do after installing a new hard drive?

    I had a 13" Non-retina MacBook Pro from mid-2012 and I bought it standard, but I upgraded my RAM from 4GB to 8GB, but also while on this website that I bought the RAM modules from, I noticed they sell Solid State Drives and I would have gotten one, but I wanted to upgrade it later on as I didn't have $500 for the 512GB flash drive for it. I need something with storage and 500GB is plenty, but I found a 960GB SSD for $500 on this website. Its a very good website for upgrades for all computers. So my question is, when I install this new hard drive, can I just hold Command+ R to install Mac OS X or do I need to go through a special process to get OS X on the new hard drive? I have an Apple Time Capsule so I have my data backed up and I'll just restore it from a backup. If I need a special cable to boot OS X to the new drive, then so be it.

    https://discussions.apple.com/thread/5210788?tstart=0
    At startup hold down the Command+Option/Alt+r keys until you see a globe on the screen. Then use disk utility to partition and format the drive HSF+ and then select Reinstall Mac OS X. whatever version of OS X that originally came on your system will be installed and then you can upgrade back to Mavericks.

  • MacBook Pro 2009 new hard drive install results in very slow function and freezing

    I just wanted to post my resolution to a problem that I had trouble finding an answer to on these forums.
    Short version:
    I replaced the hard drive in my 2009 MacBook Pro because the computer froze and upon reboot the Disk Utility said it was corrupted, but with the new hard drive the computer ran very slowly and often showed the spinning rainbow wheel. I replaced the SATA cable that connects the hard drive to the motherboard and it works perfectly once again.
    Long version:
    Recently my MacBook Pro (2009 running Snow Leopard) froze up and I performed a hard reset by holding down the power button. When I turned the computer back on it would not boot OS so I ran disk utility from the Snow Leopard install DVD. The test said the hard drive was corrupted, and since the computer is way past warranty I decided to change the drive out myself. I bought a 500GB Seagate Momentus 5400 Drive from Amazon, opened the computer and replaced the existing hard drive with the new one. When I first booted from the OS install DVD, my computer was not recognizing that any hard drive was present. I read somewhere on these forums that sometimes the formatting on new Seagate drives can't be read by MacBooks and they need to be reformatted using another computer, but I tried simply taking the hard drive out and putting it back in a couple of times thinking maybe I had just not plugged it in correctly. After the 4th attempt the hard drive magically showed up, and I was able to reformat the drive and install OS and even Windows XP on bootcamp.
    Everything seemed to be okay but applications were running slowly considering this was a fresh drive and OS install. Over time, the computer started to hang more and more. In OS I would get the spinning rainbow wheel even when doing something as simple as opening a browser window in Chrome or trying to type into a text field. When I tried to use Windows it would simply freeze after only a short time and I'd have to do a hard reset.
    I went to the Genius Bar at the Apple store which was unhelpful, so I continued searching through these forums to try to figure out the problem. I noticed a lot of people had trouble with the SATA cable that came with the computer because it's quite thin and delicate, and would get damaged when changing out the hard drive. However most of these people seemed to experience a question mark when starting up the computer, whereas mine would fully boot and be functional for a time. I thought it unlikely that a damaged cable could possibly leave the computer partially functional. Finally though I gave in a dropped the $26 for a new SATA cable on Amazon. As soon as I installed it the problem was fixed, and the computer runs as fast as when I first bought it. I don't know if I damaged the cable changing the hard drive (I was extremely careful) or if my original hard drive was not actually corrupted and the cable was already damaged. I mentioned the possibility of the cable being damaged at the Apple store and the representative said that often times they fail because people carry the laptop with one hand, and because of the way this model was designed this puts a lot of pressure right on that thin cable. Regardless, if you do plan on changing out your hard drive in your MacBook keep in mind that the SATA cable is sensitive, and that if you experience problems with a fresh hard drive and OS install the SATA cable is a likely culprit.

    If you think you have either a hard drive or a cable problem, to the best of my knowledge the only product that can help isolate both of them is Scannerz. You can check it out at:
    http://scsc-online.com/Scannerz.html
    I think that's the correct link. If it isn't and you're interested and that's wrong, just google it. I'd also check out their downloads section, especially the sort of short document on using path isolation to detect and isolate problems.
    Scannerz can detect both errors and irregularities. It uses the surface scan progress as a reference. Cable problems never show up at the same location because they're typically intermittent. Surface problems always show up at the exact same place. That's the only product (at least commercially available) that can do that.
    I don't know if this information is of any value to you because it sort of sounds like you've already solved the problem, but it might be of use if you have problems in the future.
    In any case, I've seen several posts on several different sites where people were reporting insulation break down on some of the SATA cables. Apparently the insulation breaks down and the cable starts shorting to the case.

  • Help with CS3 on Windows 7 hard drive.

    I have Photoshop CS3 on an XP hard drive.  I have a Windows 7 hard drive now and cannot access Photoshop on the other hard drive and it won't let me install in on the new hard drive.  Do I need a patch or something?  It tells me to uninstall and install again, but it's on the other hard drive and I don't know how to uninstall it there and really need to get this installed again as I need to do a memorial brochure for a friend.  Any help will be appreciated.  Thank you.

    You either have to reconnect the old drive as the C: drive and uninstall, well actually, deauthorize photoshop. then switch drives again.
    Or
    You can notify Adobe that you have more than 2 computers with photoshop installed (the old drive counts as a computer) you need then to reset your license.
    Now I am assuming how photoshop was installed, If you already had 2 drives and installed on the second drive instead of the main drive and something went wrong so you can no longer access it. Thats another story.
    Adobe has a cleaner app that can find photoshop and remove all traces of it for you, so you can resinstall it. I never used that app, so I can not give advice on how it works, but I have heard other recommend using it.

  • MacBook mc240ll/a new hard drive how to install os?

    I just got a MacBook mc240ll/a it has 4GB of ram and I just got a new hard drive for it but, I have no clue how to install the OS. Do I have to purchase OSX 10.6 Snow Leopard because I have none of the cds that came with the computer. Thanks

    Thanks for your help. I received the disc and installed the os but I had to use a flashlight because everything was dark. I finished the install and it is still dark is there any solution for this. I tried making the brightness up but, it does not work.

Maybe you are looking for