Netsh does not work to set IP address of "Wireless Network Connection"

On Windows 7 Professional
This set of commands work for configuring the "Local Area Connection"
netsh interface ip set address name="local area connection" static 74.94.87.157 255.255.255.248 74.94.87.158 1
netsh interface ip set dns name="local area connection" static 8.8.8.8
netsh interface ip add dns name="local area connection" 68.87.77.130 index=2
BUT for the WiFi connection, this command errors with this message "ELEMENT NOT FOUND"
netsh interface ip set address name="Wireless Network Connection" static 74.94.87.157 255.255.255.248 74.94.87.158 1
BUT the 2 following dns commands DO work for the Wifi Connection.
netsh interface ip set dns name="Wireless Network Connection" static 8.8.8.8
netsh interface ip add dns name="Wireless Network Connection" 68.87.77.130 index=2

I FOUND A SOLUTION
I manually renamed the interface from "Wireless Network Connection" to "Wifi"
Then when I use "WiFi" in the command line, I no longer get the
ELEMENT NOT FOUND error.
I have no idea why renaming the interface works . . as shown on original post above, "set dns name" command worked without the name change, but the "IP set Address" did not work.
Anybody know what this is about ?

Similar Messages

  • Macbook Pro 2011 DVI HDMI out does not work with TV when the power cable is connected

    My Macbook Pro (Early 2011) DVI HDMI out does not work with TV when the power cable is connected. If get the blue screen and then can use the macbook but nothing is displayed on the TV. If i go into display I can see that there are two screens but nothing displayed on the TV. If i take the power cable out at this point the TV shows the second desktop as expected. If i then reconnect the cable, the screen flickers, as though it is being affected by the power cable, and the screen goes blank on the TV. Only if i remove the DVI cable do i get the blue screen again. If i remove the power cable and reconnect it will do it every single time, so i cannot see it being a TV issue or a minor glitch.
    I have had this working previously but at the minute it seems to not be playing ball....any thoughts
    Thanks
    Dan

    BUMP
    Any ideas?

  • When I open firefox before connecting (via 56k modem) or if I leave a previous section open, disconnect and then reconnect, firfox does not work, it remains offline, even though internet is connected. I have to close firefox and reopen

    When I open firefox before connecting (via 56k modem) or if I leave a previous section open, disconnect and then reconnect, firfox does not work, it remains offline, even though internet is connected. I have to close firefox and reopen

    Thanks for the reply. I never get the option to "Restore Previous History" from History. I don't even have the box checked that asks to delete the history when Firefox closes. I don't know what's wrong, no matter what, I always lose everything. I have the box marked "Show my windows and tabs from last time" for when I open Firefox, but it never shows that, just my homepage. Also, when I check my History, it only shows the pages that I opened since I started Firefox, nothing from before. Even if I were to open up 10 pages now, close Firefox, and open it, the history would only show the homepage that opened this time, not any of the 10 pages that I opened 5 minutes ago.

  • How do i restart my ipod touch if the power off button does not work and it is disabled and it say connect to Itunes

    how do i restart my ipod touch if the power off button does not work and it is disabled and it say connect to Itunekyl

    Place the iPod in recovery mode using this program. and then restore via iTunes.
    RecBoot: Easy Way to Put iPhone into Recovery Mode

  • Lead Selection does not work after setting filter for ALV.

    Hi, Can you please suggest on below scenario :
    I have a Node with a sub node in it .
    I am using the supply function on Sub Node to retrieve the date based on Parent Node.
    There are two ALV's to display parent and item data. The issue is when a filter(user defined filter) is done on Parent table, the supply function does not work. The value is that of the selected row before setting the filter. Even after removing the filter, the item data is stuck and does not change on Lead Selection.
    One thing I noticed is if the child table is a table UI, there is no issue. The only problem is when the second table is ALV
    Thanks In Advance

    Hi Prashanthi,
    Your issue can be resolved as below
    Create an event handler method 'set_alv_data'  for the event 'ON_LEAD_SELECT' of parent alv
    Write the below code inside the event handler method
    METHOD set_alv_data.
      DATA lo_node TYPE REF TO if_wd_context_node.
      DATA lv_path TYPE string.
      DATA lv_index TYPE string.
      lv_index = r_param->index.
      CONDENSE lv_index.
      CONCATENATE wd_this->wdctx_my_parent_node
      lv_index
      wd_this->wdctx_my_child_node
      INTO lv_path SEPARATED BY '.'.
      lo_node = wd_context->path_get_node(
          path                          = lv_path
      DATA lo_interface TYPE REF TO iwci_salv_wd_table.
      lo_interface = wd_this->wd_cpifc_alv_child( ). "get the ref of alv comp of child
      lo_interface->set_data(
        EXPORTING
    *    only_if_new_descr =
          r_node_data       = lo_node
    ENDMETHOD.
    The above code sets the data node of child alv based on lead selection of parent alv data.
    Note: Replace 'parent_node', 'child_node'  with your nodes & 'alv_child' with your alv component name of child alv.
    If you want to control the data of child alv on filter function, you can use the event ON_STD_FUNCTION_AFTE and once you define the filter you get the r_param->id = 'SALV_WD_FILTER_DEFINE'  & now you can clear data of child alv.
    Hope this helps you.
    Regards,
    Rama

  • My sound system does not work AFTER installing pc to tv wireless connection

    my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

    Hi,
    You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
    Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
    one used by the Form contact for Form Invoice.
    Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
    VS General Question forum mainly discusses
    the usage of Visual Studio IDE such as
    WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
    System and Visual Studio Editor.
    Thanks,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • Tomcat does not work when using only netcfg to start network

    hello!
    for myself i wrote a script to connect automatically to a wireless network using netcfg. i do not start my network via the daemon (/etc/rc.d/network).
    i have a project and so i want to use tomcat. but it does not work correct, i can start it, but i can't connect via "localhost:8080". when i start my network using the network daemon it works! apache runs fine, but i need tomcat!
    can someone help me please?
    thx, marv

    where is "lo" enabled in the network script? i did not found it and/or i have no idea which function enables it.
    can you help me please? can i just copy the lines of code to my own script and it will enable lo?
    mfg iggy

  • Cascading LOV does not work when setting the value of the parent LOV with DA

    Hello All,
    Using APEX 4.2.2.
    I have tow LOVs
    Parent LOV item is: P50_TYPE
    Child LOV item is :  P50_PROJECT_ID
    In other words in the attributes of the item P50_PROJECT_ID we have :
    > Cascading LOV Parent Item(s): P50_TYPE
    > Page Items to Submit: P50_TYPE
    > List of values definition: something similar to:
    Select * from mytable where type = :P50_TYPE
    I use DA that execute JS code to set the value of the P50_TYPE item
    something similar to:
    > $('#P50_TYPE').val(2);
    Having done this, the P50_PROJECT_ID item does not get refreshed, when the value of P50_TYPE is changed. Namely, P50_PROJECT_ID remains empty, unless end user manually changes the value of P50_TYPE.
    Any help please ?
    Regards,

    Thanks Scott,
    By the way, I remember reading a thread posted by you about  Sumneva Drag & Drop Report Region plugin that was answered by Tom . But, I cannot find this plugin anywhere. Does not it supported in APEX 4.2 ? Is there any alternative out there ?
    If you use it, and it works find with you, can you please send it to me on [email protected] ?
    Regards,
    Fateh

  • WRT300N Router does not working with Intel 4965AGN adapter on Wireless-N

    Hi! I have recently bought the laptop Acer 5920G with Intel 4965AGN network adapter and Windows Vista. I have read that WRT300N Router is supporting Draft-N standard, so I purchased it. The router is working fine on Wireless-G 54Mbps (firmware - 2.00.17), but not on Wireless-N. I tried to enter the following settings: ssid - any non-linksys name;  radio band - wide; n-channel - 9; standard channel - 11; beacon interval - 50; Fragmentation threshold - 2306; RTS threshold - 2307, but nothing has happened, connection still remains 54Mbps. How should I configure the router and network adapter to get Wireless-N?

    okay... try reflashing/upgrading the firmware on the router, after reflashing the firmware on the router, reset it back to default settings and reconfigure it according to ISP settings...edit the wireless settings again, make sure that "wireless mode" should be mixed...
    on the vista computer, click on start >> control panel >> network & sharing center >> manage wireless network and try removing existing wireless networks from profile and manually add wireless n/w profile according to wireless settings of the router...check whether it makes any difference or not and let me know.

  • Enter-PSSession does not work when a IPV6 address is entered as the -Computer value.

    I cannot get Enter-PSSession to work with a specific IPV6 address and when TrustedHosts is also set to this address.
    NOTE:  If TrustedHosts is set to "*", then the command succeeds, so I'm pretty sure the target is configured correctly to allow remote access.
    Example:
    set-item wsman:\localhost\Client\TrustedHosts "fc00:10:114:247:2d0b:6bf8:c982:ce10"
    ENTER-PSSession -Computer fc00:10:114:247:2d0b:6bf8:c982:ce10 -Credential <somecred>
    ENTER-PSSession : Connecting to remote server [fc00:10:114:247:2d0b:6bf8:c982:ce10] failed with the following error message : The WinRM client cannot process the request. Default authentication may
    be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure
    TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more
    information, see the about_Remote_Troubleshooting Help topic.
    At line:1 char:1
    + ENTER-PSSession -Computer fc00:10:114:247:2d0b:6bf8:c982:ce10 -Credential Admini ...
    + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        + CategoryInfo          : InvalidArgument: (fc00:10:114:247:2d0b:6bf8:c982:ce10:String) [Enter-PSSession], PSRemotingTransportException
        + FullyQualifiedErrorId : CreateRemoteRunspaceFailed

    Ping works by IPv6 or name.
    For name, I put the IPv6 address and name in my hosts file because during testing, I move from a domain to a workgroup occasionally.
    Example:
    Target
    ipconfig
    IPv6 Address. . . . . . . . . . . : fc00:10:114:247:44d1:f91f:2ceb:b032
    Client Computer
    /etc/hosts
    fc00:10:114:247:44d1:f91f:2ceb:b032 slo-2k8r2-64-5
    Ping slo-2k8r2-64-5
    Reply from fc00:10:114:247:44d1:f91f:2ceb:b032: time<1ms
    Powershell 
    set-item wsman:\localhost\Client\TrustedHosts "fc00:10:114:247:44d1:f91f:2ceb:b032"
    ENTER-PSSession -Computer fc00:10:114:247:44d1:f91f:2ceb:b032
    // ENTER-PSSession : Connecting to remote server [fc00:10:114:247:44d1:f91f:2ceb:b032] failed with the following error message : The WinRM client cannot process the request. Default authentication may
    Again, if I set Trustedhosts to "*", then it works.
    Example, 
    set-item wsman:\localhost\Client\TrustedHosts "*"
    ENTER-PSSession -Computer fc00:10:114:247:44d1:f91f:2ceb:b032 -Credential name
    > hostname
    // Returns SLO-2K8R2-64-5
    // IPConfig also returns fc00:10:114:247:44d1:f91f:2ceb:b032

  • IsValid does not work with extended email address

    This invalidates valid addresses.
    <cfset testemail = '"No One"
    <[email protected]>'>
    <cfoutput>#testemail#</cfoutput><br />
    <cfif isValid("email",testemail) >
    good email
    <cfelse>
    bad email
    </cfif>
    Any ideas how to make this work with extended
    addresses?

    > blah blah <[email protected]> is a predictable format.
    You can use string functions to find the part between the angle
    brackets and apply the isValid function to that.
    Yep, but isValid() just doesn't reliably validate even the
    email address
    part of that string (well: that *exact* example, sure it
    will). It can't
    be used to RELIABLY validate email addresses. The regex it
    uses is
    incomplete. It'll validate a lot of valid email addresses,
    but it'll also
    reject a number of valid patterns, and validate some that are
    wrong.
    Adam

  • Mail for Exchange does not work when set to manual...

    I set up mail for exchange and it works beautifully when set to always on, however many times I want it on manual so I can only check at specific times when I'm away from a pc, but it doesn't seem to work.
    When I click synchronise, it appears as if it syncs and disconnects, but it doesn't update anything. If I try the same when I'm looking at the mail for exchange settings, then it tries to connect and says error connecting, try again later.
    So i switched to always on, it worked, back to manual, and it seems that the first attempt was successful, but I know it'll stop working later.
    Any idea what the problem is with manual checking?

    I set up mail for exchange and it works beautifully when set to always on, however many times I want it on manual so I can only check at specific times when I'm away from a pc, but it doesn't seem to work.
    When I click synchronise, it appears as if it syncs and disconnects, but it doesn't update anything. If I try the same when I'm looking at the mail for exchange settings, then it tries to connect and says error connecting, try again later.
    So i switched to always on, it worked, back to manual, and it seems that the first attempt was successful, but I know it'll stop working later.
    Any idea what the problem is with manual checking?

  • HT4183 The "Trust" setting does not work with 10.8.2, even openssl s_client -connect ...:636 returned CONNECTED(00000003) verify return:1

    even openssl s_client -connect ...:636 returned
    CONNECTED(00000003)
    verify return:1
    No client certificate CA names sent
    SSL handshake has read 1518 bytes and written 456 bytes
    New, TLSv1/SSLv3, Cipher is AES256-SHA
    Server public key is 2048 bit
    Secure Renegotiation IS supported
    Compression: NONE
    Expansion: NONE
    SSL-Session:
        Protocol  : TLSv1
        Cipher    : AES256-SHA
    Key-Arg   : None
        Start Time: 1363044139
        Timeout   : 300 (sec)
        Verify return code: 0 (ok)
    Connect to OD without SSL works fine.
    Anybody else?
    Henri

    Hi,
    here are some more informations about the problem.
    The root CA certificate is imported as trusted in the system keychain of the server and the client. A certificate evaluation returns "valid certificates, trusted ...".
    The client bind fails with this messages, e.g. Kerio Control is able the use LDAPS, so it seams just the problem with the trustability of the certificates. Keychain trusts the certificates, OD client bind not, this is not so consistent.
    Any idee?
    Thanks
    Henri
    2013-03-14 19:39:02.776804 CET - Trigger - notified opendirectoryd:nodes;lastServerChanged;/LDAPv3/ldaps://macpro....:636
    2013-03-14 19:39:02.793467 CET - 71825.330426.330427, Module: AppleODClientLDAP - unable to create connection to LDAP server - ldap_search_ext_s for the ro
    otDSE failed with error 'server connection failed' (-1) error:14090086:SSL routines:SSL3_GET_SERVER_CERTIFICATE:certificate verify failed (self signed cert
    ificate in certificate chain)
    2013-03-14 19:39:02.793501 CE
    CONNECTED(00000003)
    depth=1 /C=DE/...
    Certificate chain
    0 s:/CN=macpro...
       i:/C=DE//OU=IT/CN=*.office.../emailAddress=admin@...
    verify error:num=19:self signed certificate in certificate chain
    verify return:0

  • Migration Assistant not working with OS X Lion via Wireless Network?

    Anybody know how to assist me here?
    Basically, I have two iMacs on seperate floors of my home.  They are newer models (both purchased last year) and I have upgraded both of them to Lion and just ran a system update on both of them to ensure they are both running the exact same OS with updates and all.
    When I attempt to use the migration assistant over my network, it just says its attempting to find the other computer but never moves past that step, as if they aren't connecting or even finding each other at all. 
    I'm relatively new to the mac family and am very happy I've finally made the switch last year and am still learning the in's and outs and am simply stuck here and not sure what to do to get this to work. 
    Thank You

    Try running software update to install 10.7.1.  This update reportedly fixes your issue.  Check out http://support.apple.com/kb/DL1437 for more information.
    Good luck

  • File sharing with MBP does not work

    The problem is that I cannot connect to my first-gen MacBook Pro from my 2 Ghz Intel iMac in my own home network. I have tried opening all ports in the sharing menu without success. The laptop shows up in the finder window but no connection is made. There is not even an error message. It simply says (after a long while) that the connection failed. Nothing even happens when I try to click on the "connect as" button. This is true for file sharing and screen sharing. I can connect to the iMac from the laptop, ironically enough. I was able to connect both ways at one point. My set-up is as follows: airport express connected to modem/router; iMac and laptop connected wirelessly to airport express. Any ideas would be great. I am at a complete loss as the laptop has no other connection issues of any kind.
    Update: I just got an error message for the first time: The server may not exist or it is not operational at this time. Check the server name or IP address and your network connection and try again.

    Connecting via "connect to server" in finder menu using afp does not work either. FYI. It just tries connecting for a long while and then gives me the following error (-36). The finder cannot complete the operation because some data in "afp://....." could not be read or written.

Maybe you are looking for

  • Authorization issue within a table in BI

    Hello All, Here is my authorization issue : We have set up an authorization on infoobject Zapplication. End user is allowed to choose "HR" only. In Rsecadmin, infoObject Zapplication is restricted to "HR" Then, this authorization object has been assi

  • How to change Billing status of delivery-related billing documents?

    Hi Experts, Now I meet with the problem with the billing status. I want to create a billing reference delivery notes, but the billing staus of delivery-related billing docuemnts is  blank, I want to chage it to 'A' so as to create a billing refer to

  • Re-installing Final Cut Studio 2 on Snow Leopard?

    Hello All, I had reason to uninstall Final Cut Studio 2 off my machine because of problems with Compressor and Motion. I followed the Apple help doc on how to uninstall FCS2. However when I go to re-install from the main install disc, it runs fine un

  • How to turn off this horrible hovering cursor?!

    When my cursor hovers over anything for more than a second or two, it selects whatever it is.  How can I get rid of this nightmare of a feature? Thanks, Tom

  • Error in cheque printing

    Hi,   when i try to run payment run for a payment method for cheques, it is using up 4 cheque numbers. for ex: if next available chque num is 1064 when i finish payment run and check the next available cheque number it will be 1068. when i check for