Networking to use pcAnywhere on Parallels VM XP PRO

I am a retailer and want to us a iMac 2.2 Leopard 10.5.2. The Point of Sale software only run on XP which I have VM'ed using Parallels. To service the POS software the POS support needs to access the VM XP using PcAnywhere on one IP address. The problem is that my Netcomm ip is 192.XXX.1.1, Air port Extreme is 192.XXX.1.100, the iMac ip 10.X.1.1 and the XP on Parallels is 10.211.XX.3 .
Basically, I have two networks between both routers. The port forwarding
needs to jump between both in order to reach it's destination. The
pcAnywhere connection first reaches the Netcomm router which forwards the
connection to the Apple Airport . From there, the Airport needs to send the packets to the XP bypassing the OSX IP computer, but in order for it to do that it needs to send the details to the correct IP address.
Does anyone have ideas. I want all the Mac advantage but run my Franchisors XP based Point Of Sale.

When you remove the flash drive are you ejecting it or just unplugging it? If the latter then you need to use the system eject to remove it. You must also eject it properly from within Windows.
It would help if you provided the version of OS X you are using in your configuration as well as more info on the hardware model and configuration. This information helps us know about your setup in order to provide assistance.
Also, what version of Parallels are you using? Do you have USB support turned on in Parallels configuration? Have you searched the Parallels forum for possible solutions or posted your problem on their forum? This should be your first place to look for help, not the Apple Discussions.

Similar Messages

Network issue using Time Warner, Airport Extreme, MacBook Pro OSX, Windows7

I have the following on my home network:
- Time Warner cable-internet and phone service.
- Apple Airport Extreme Base Station hooked up to the cable modem
- MacbookPro running OS 10.6.3 connected wirelessly to airport extrm
- HP Laptop running Windows 7 connected wirelessly to airport extrm
- HP Officejet Pro 8500 connected to wirelessly to the airport extrm
- iPhone connected wirelessly to the airport extrm
- XBox connected via ethernet cable to airport extrm
- USB external hard drive connect via USB cable to airport extrm
My network worked fine with only my Macbook Pro, Airport Extreme, iPhone, XBox, and occasionally my buddy's Macbook Pro all on the network at the same time.
I recently added an HP Laptop running Windows 7 and a wireless HP Printer to the network at the same time.
Now if both the Windows 7 PC and the Macbook Pro are on the network at the same time, one of the machines will get booted from the internet. At one point, I got a message on my MacBook Pro that said another computer on the network is using the same IP address. I also have trouble communicating with the new HP printer if both the Windows 7 and the Macbook Pro machines are on the network at the same time.
How should I set up my airport extreme to allow all machines to function properly on my network. Right now, the network is set up to receive IP addresses automatically through the DHCP server. I read somewhere that maybe setting up the computers to manual static IP addresses and manually entering in the DNS server info into the airport extreme may fix my problem. I also read that configuring the network to all share a single IP address will fix the issue. How do I set this up. I would also like to keep my network invisible from being seen. Is this still possible?
Thanks for your help on this!!

To change the IP address on a Mac, go to settings, then select the network interface you use, then, change Automatic to manual. I don't know how to do this on windows 7, and you can access and change your printers settings by clicking in the bookmark windows on Safari, clicking printers, and open up it's settings.

Network buffer used by Data Guard asynchronous shipping process

Hi, all,
I am investigating the amount data that could be loss if we are using LGWR ASYNC for the redo transport services. I read somewhere it says the maximum exposure to data loss is the size of network buffer used by Primary database to ship redo apply. Where can I find out the size of this network buffer?
Thanks a lot in advance.

it says the maximum exposure to data loss is the size of network buffer used by Primary databaseIn 10.2 lns async reads directly from online log files, no buffer.
However, even with the buffer the above statement is incorrect.
There is no maximum to the exposure of data loss in either max performance or even max availability modes.
The exposure is a quantitative measure that depends on the speed of communication with standby.
You can evaluate it by comparing the rate of redo generation on primary ('redo blocks written' in v$sysstat) with that of redo apply on standby ('redo blocks read for recovery' in v$sysstat), or, easier, v$dataguard_stats on standby.
Oracle dataguard software sometimes [log switch] artificially increases immediate short-term exposure by parallelizing redo shipping.
But this parallelization makes it more efficient (and thus lessens this exposure) in the long run.
The only mode with maximum exposure limit is maximum protection, and that maximum is zero.

How can I connect to SQL server database thru local network by using JSP?

I'm currently doing a project by using JSP..And I need to display record from the SQL Server database in our school's local network. May I know how can I do that? How can I write the code so that I can able to access the SQL Server databsase Throught school's network by using JSP? Please tell me step by step how can I do that. I'm using Tomcat 4.1 as Web Server. And I had J2SE and J2EE installed in my computer.

first you have to establish a ODBC DSN on your computer,
that connects to the database...you can do that from your control pannel.
i assume that the TOMCAT server is residing on your computer....(if the webserver is in other computer then you would have to create a System DSN on the data sources ODBC option in the settings>control pannel of that machine)
then you can use that DSN name to connect to the data base from the class file....for further assistance on how to create the class that access the tutorials in sun site.
regards
G

Unable print scheduled report on network printer using BOEXI 3.0

Hi,
I'm unable to print a scheduled report on network printer using BOE XI 3.0. I get the following error
Error Message: Error in File ~ce6a054be1a25b52.rpt: Request cancelled by the user. ]
Has anyone encountered this kind of problem and know what the solution is?
Thanks,

Hey Falk,
Thanks for the response.
I can print on a network printer after I changed 'Crystal Reports Job Server' to run under a user account that has privileges to access the printer.
To answer your questions regarding the problem:
>Can you schedule the report successfully ?
>>Yes I was able to schedule the report successfully
>Can you print the report successfully?
>>NO the scheduled task would fail with the error message as posted above.
Thanks,

Safari of my Macbook (on WiFi) suddenly fails to connect to the Internet. A popup window message says another device on the network is using my computer's IP address.

But then there was still no Internet access even after I have disconnected all other home computers (a total of four including the Macbook and one iMac desktop. For simplicity, I shall categorically called them Mac hereafter unless otherwise specified. The Macs are operating on WiFi.).
The window message recommends changing the IP of either the Macs or the other device. The latter of course does not apply because I don't think the other device is one of my computers.
My questions:
(1) Why did that happen suddenly since the Mac and other computers on the WiFi was working fine in the morning (as well as days before) and then all of a sudden an unknown device is using my computer's IP? As far as I (we) can remember, we did not do any thing unusual this morning nor had we downloaded any special programs.
(2) How do I change the IP since it requires Internet acess to do it and since I can't access the Internet on the Mac?
(3) I am almost sure the problem is not caused by the Internet service because when I connected the Ethernet cable from the DSL modem to an old Windows PC, I got Internet via Internet Explorer. [I am actually sending out this message via IE on my PC.] However, when I cennected the Ethernet line from the modem to a WiFi router (Airport Extreme) and then connect the router and the old PC, I did not get Internet on either the Mac nor the PC. Similarly, there was no Internet on both Mac and PC If I connect Ethernet only between the modem and the router but not between PC and router. So, the question is whether a third unknown party has gotten hold of my Mac IP address and is trying to break into the Mac? Can it steal my personal info?
(4) How can I repair the Mac now and prevent future recurrences? Is changing the IP address the way to do it? (But like I said before I had tried but could not change the IP because I did not have Internet access on the Mac. Is there an alternative method?)
(5) I wonder if a computer's IP address remains constant if you don't change it. The reason I am asking this question is because the aforesaid window message on the Macbook--not sure about the iMac--shows a different IP address--a few numerical digits were changed--almost every time it pops up following every failure trial of mine to access the Internet. Was the Macbook trying to change the IP for me or was there some thing not right?

Re: Another device on the network is using your computer's IP address.
This message/problem was occuring intermittently for me in a household with two MacBooks accessing one Airport extreme. Rebooting the modem and router would only temporarily fix the issue for me, so I spoke with a friend who works for Apple and it seems that the Airport Extreme settings were at the root of our particular issue.
The router(Airport Extreme) recieves only one IP address from the modem and in order to allow it to share the IP address with two computers at once, the solution in my case was through:
Applications>Utilities>Airport Utility>Manual Setup>Internet
under Internet Connection- Select "share a public IP address"
under NAT, check the box for "enable NAT Port Mapping Protocol"
(this will allow the sharing of one public IP address with multiple devices)
if this is a new setting, then click "Update" and the Airport Extreme should reboot itself with new settings applied.
When all else is working properly, this is a satisfactory solution in my case.

I am trying to set up home sharing between my iphone 4s and mac which is running itunes 11. Both are connected to my home wifi network and using the same apple id but on the iphone app it says 'Turn on Home sharing in iTunes on your mac using account ***

I am trying to set up home sharing between my iphone 4s and mac which is running itunes 11. Both are connected to my home wifi network and using the same apple id but on the iphone app it says 'Turn on Home sharing in iTunes on your computer or apple tv using account ***
Does anybody have suggestions as to why this is the case?

Understanding Home Sharing - Support - Apple
Hope this helps.

Using BAPI_PO_CREATE1 in parallel processing

Hi experts,
I am using BAPI_PO_CRATE1 in parallel processing to create multiple Purchase Orders. The Programs is creating only one PO (the Ist one) however it should create multiple PO as per the program and data.
For rest of the data it is returning error message saying "No instance of object type PurchaseOrder has been created".
Please suggest how can I fix this issue.
Points are sure.
Thanks & Regards.
Anirudh

Without looking at some poriton of the code around this call and your parallel processing logic, it will be difficult to say.

This item is over 20MB. You must connect to a wifi network or use iTunes on your computer to download it.

Verizon wireless network - unlimited data plan.
iPhone 4 - iOS 5.0
"This item Is Over 20MB
You must connect to a Wi-Fi
network or use iTunes on your
computer to download it."
This message was given when trying to update an app I already had installed on the phone. My question is why? Is this a problem with the programming making you connect to the internet via link or Wi-Fi. Or is this a limitation on the Verizon network? Or perhaps a limitation set in place by Apple to prevent long downloads? So I came here hoping to get some hard cold facts. (since Verizon associates would not or simply could not help me)
Personally I could care less if it took 6 hours to download an update. I do however have a problem paying a telephone service an insane rate to get "unlimited data" and not being able to receive unlimited data.
Any help would be greatly appreciated.
-Luna

Telstra Australa
I dont have Wifi in the countryside and theres no DSL, only 3G and 4G. why should I have to buy another 3G service when I already have one? This is one of the problems of globalisation, because AT&T cant handle the volume, the whole world has to suffer.
I pay per gigabyte, so dont need these restrictions Apple! Its mine to use.
Daniel.

OK so I just made a wireless network and using the apple box or whatever. And I want to change the network name. How do I do that?

OK so I just made a wireless network and using the apple box or whatever. And I want to change the network name. How do I do that?

Just want to confirm that I am also having this issue, The connection is fine, and it is in fact charging (@ 100%)
Everything Rick has said is like an echo to what is happening to me.
I have tried re-installing iTunes, and restarting the Bonjour service, sadly there is no change.
earlier before i updated iTunes it recognised my iPod but said that I had to update iTunes in order for it to work.
So i updated iTunes but now it's not even showing the device anywhere.
In case this helps:
OS: Windows 8.1
iTunes version: 11.3.1.8
Device: 5th generation iPod touch 16GB with ios 7

How do I resolve, "Another device on the network is using your computer's IP address?"

Another device on the network is using my computer's IP address

This error message can be seen under several different circumstances. I've seen it after rebooting my router or after an unintended reboot of my computer (like a force quit). If your devices are still able to access the Internet, ignore it. If one of them can't access the Internet then there's an issue with your network that requires resolving.

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

Yes. You can directly connect an 802.11n AirPort Express Base Station (AXn) using an Ethernet cable. The AXn would then just need to be configured as a bridge to allow the D-Link to continue to provide both NAT & DHCP services for all network clients connected to either router.
In this configuration, the AXn would broadcast a wireless network for your wireless network clients to connect to.

When I am on my home wifi I can send e-mail. When I am not on my home e-mail but on a wifi network or using the 3g network I cannot send e-mail. HELP HOW TO FIX.

When I am on my home wifi I can send e-mail. When I am not on my home e-mail but on a wifi network or using the 3g network I cannot send e-mail. HELP HOW TO FIX.

I know this question is a few years old now, but I recently found myself having the exact same issues;
Using my iphone or ipad at home created no problems at all, but I couldn't send e mails when away from my home network.
I recently switched broadband supplier at home and set up a new e mail address, then my problems began!
I openly admit I'm not great with technology and, to be honest, some of the answers provided on these forums confuse me more than the questions!
But this worked for me:
I went along the lines that the fault wasn't with my idevice but possibly with the broadband provider (in my case Plusnet) so I contacted their customer support.
They referred me to the set up process shown below;
From your home screen press Settings.
From the setting menu, choose Mail, Contacts, Calendars followed by Add Account…
From the Add Account… menu choose Other.
Fill in your Full Name, Email Address, Password and Description and press Next.If you need help with these, there's more detail underneath the screenshot.
Full name: Enter your name (or the name you'd like people to see when you send them email)
Email Address: Enter the address you're setting up, this could be a Plusnet address ([email protected]) or a hosted domain address ([email protected])
Password: Enter the password for your email address (I don't know what this is)
Description: Enter a useful description of the email address you're setting up (e.g. Mum's email). You can put whatever you want here
Press Next to continue.
More settings will appear. Some will already be filled in.Enter the Incoming and Outgoing Mail Server details and press Next. If you need help with these, there's more detail underneath the screenshot.
IMAP/POP This will default to IMAP - it's up to you which one you want to use (I don't know what to choose)
Incoming Mail Server settings
Host Name: For IMAP this is imap.plus.net - for POP, this is mail.plus.net
User Name & Password: Enter the username and password for the email address you're setting up (I don't know what these are)
Outgoing Mail Server settings
Host Name: relay.plus.net
User Name & Password: These are optional, but if you want to send mail while on the move (e.g. while connected to mobile or wireless networks), we recommend filling these in.Enter the username and password for the email address you're setting up (I don't know what these are)
When you're finished, press Next.
If the box shown below appears, press Yes (you may need to do this twice).
After a minute or two, your email address will be set up and ready to use.If you chose IMAP when setting up you’ll be able to choose whether you want to use Notes (if you chose POP you’ll be taken back to the settings screen from step 2). Press Save when you’re done.
That's all you need to do. To start checking your email, go back to your home screen and press Mail.
Now I fully understand that it may be different for each broadband provider but the processes must be similar.
The key appears to be in setting up the outgoing message server settings in step 5. Where it says "optional, but if you want to send mail while on the move (e.g. while connected to mobile or wireless networks), we recommend filling these in.
http://www.plus.net/support/email/setup/ios-setup.shtml#pagetop
Where it says "we recommend" I think it should read "you must fill these in"
I went back to Settings - Mail,Contacts, Calenders - click on the offending account and click on the account shown.
Under OUTGOING MAIL SERVER click on the server, in my case relay.plus.net, and click again to show the details. make sure you enter your user name and password and after a few seconds the account will verify and show a load of ticks.
I tried this on my phone this morning while on 3G only. I sent an email to another of my addresses and immediately got the response that the message couldn't be sent as the recipient was rejected and the message had been placed in my Outbox. I followed the above steps and immediately heard the satisfying "whoosh" as my mail was sent. 10 seconds later another satisying beep as my e mail arrived at my alternate account.
Hope this helps anyone else with a similar problem.

Can you get an iphone 5 at target that uses AT&T or Verizon network and use the Straight Talk plan from Walmart?

Can you get an iphone 5 at target that uses AT&T or Verizon network and use the Straight Talk plan from Walmart? I don't have AT&T or Verizon network and I don't want to get them but I was just wondering if you can get the iphone 5 that is at target and use it for the straight talk plan. I will be getting the straight talk plan but I would like to do some research on the iphone 5 first for straight talk. At walmart the phone is $544.99 and I think it will be a lot cheaper to buy it at target.
Thank You!

When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.

I have a 4 gen Time Caps. and a 2nd Gen Airport Extreme I would like to extend my TC network to use the Extreme for the purpose of having internet available to my TV box wired. Is this possible and how to I get them to work together?

I have a 4 gen Time Caps. and a 2nd Gen Airport Extreme I would like to extend my TC network to use the Extreme for the purpose of having internet available to my TV box wired. Is this possible and how to I get them to work together?
How can I get my Time Cap (TC 4 gen) to recognise my 2gen Airport Extreem (AE)
Frank

Thanks for the info, this really helps.
Power up the AirPort Extreme for a few minutes, then hold in the reset button on the back of the Extreme for 10 seconds and release. Allow a full minute for the Extreme to restart to a slow, blinking amber light.
It might be possible to use wireless to configure the Extreme, but I recommend using a wired connection. Temporarily, connect an Ethernet cable from your Mac to one of the LAN <-> ports on the Extreme.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on AirPort Extreme.
The illustration below shows an AirPort Express. You will see AirPort Extreme on your screen.
AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Extreme will be configured to extend the Time Capsule network.
Enter a device name that you want to use for the Extreme and click Next
Wait a minute while AirPort Setup configures things for you. When you see the message of Setup Complete, click Done.
You can disconnect the Ethernet cable that you used for the set up now. Things should be working. The Extreme is providing additional wireless coverage the the Ethernet ports are enabled. You can connect to any port that you want since they all operate the same in this type of setup.

Networking to use pcAnywhere on Parallels VM XP PRO

Similar Messages

Maybe you are looking for