Networking With Pc's =-(
I need to create an LAN with my mac and PC. The MAc has Tiger. The PC has Windoes XP Pro.
I do this with my XP Home / Tiger setup at home. You enable file sharing on the mac, also making sure to enable windows file sharing, and it tells you the address you need to access the Mac. You can then simply drop files in the Mac's drop box, or log on to the mac as it's registered user, at which point all the files on the mac become visible to the PC.
Similar Messages
-
How do i create a little network with my i-mac and macbook
how do i create a little network with my i-mac and macbook
Hello:
To give a sensible answer, a little more information is needed.
I am guessing that you want to set up a wireless network as you have both a desktop and laptop.
There are some pretty good tutorials/articles in the knowledge base articles.
Barry -
How do i use my time capsule and extend the network with airport express
I have a new iMac and Time Capsule, how do i extend the network with airport express. My time capsule does have a guest net work, and logins and passwords? I am no computer person. So for me it would have to be spelled out.
Use the search as this has been done to death ..
Bob Timmons is the expert on this.. look at his answers here.
https://discussions.apple.com/thread/4274187?start=0&tstart=0
https://discussions.apple.com/message/21856077#21856077
This has been automated in the v6 utility. I am used to doing it manually in v5 utility which is also fairly easy.
Apple doco is also good to read.
http://support.apple.com/kb/HT4145
http://support.apple.com/kb/HT4259
Note.
You cannot extend the guest network unless everything is up to date 7.6.3 firmware. And that is only with the TC as the main router in the network.
All apple routers can be configured as the main wireless or as the extend wireless.. so don't worry if a post uses express or extreme or TC.. they are for wireless, the same thing. -
I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off. How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM. My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore. Connected those drives to TM via firewire and could see the drives and access them.
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc. I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads. Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system. I really didn't want to monkey around too much with my system. But are there other options to connect the new TC. Can't find info anywhere for this and called apple who gave me the info above. after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light or repair it in disk utility if it should become corrupted.
For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working. Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
Now a rant. I can't believe in this wireless age that Apple would make a product that cant join a wireless net work. The apple rep said i could return it and look for the previous TC that would join an existing wireless network. Are we going backwards?
Thanks!
lennydasOk... it is getting a bit clearer but there are still some questions.
I connect to the internet via airport only and it is pretty fast.
I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed. I heard that bridging slows down everything and then there can be port issues with mail etc.
I think this is mistaken.
Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
If the computer is close it will be faster than the FIOS.
You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC. the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
Thanks again!
You cannot extend to a non-apple wireless router.
You cannot use join a wireless network because when you do the ethernet ports will be cut off.
But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
Join in the express is the only apple router that still allows an ethernet connection.
For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options. -
Setting up network with newer and older AirPort Extremes
Okay, I thought this was going to be so simple. I have a newer (like a year old - square) Airport Extreme that I have three computers wirelessly hooked up to in the house. Great... so now, I want to hook up the old iMac in my son's room that doesn't have a wireless card to the network. It is too far away to use the ethernet cable into the back of my newer Airport Extreme station so I figured I'd dust off the old saucer type base station, plug the ethernet cable into that in my son's room and then just easily get the old base station to network with the newer one wirelessly.
Not so easy. The newer one has no reference how to make a network with other base stations whatsoever and the old book describes how to with the Airport Admin Utility which is not available to the newer version, just Airport Utility and it does not have the WDA options listed. I tried to extend the network and then Doh! The whole network disappeared.
Is this a compatibility issue with the older and newer base stations? Would it just be easier to put in a wireless card to my very old iMac, if that's even possible? Has anyone successfully networked an old and new base station together? If so how?
Thanks!Welcome to the discussions!
When you have an older "g" device (the flying saucer) and a newer "n" device (the square one) in order for them to communicate using wireless only, you must configure both of them in what is known as WDS configuration.
This is a quite tricky setup for most users. The best set of instructions that I've seen for this comes from expert user Tesserax in this thread:
http://discussions.apple.com/thread.jspa?threadID=2355832&tstart=0
If you elect to try this type of setup, you will probably need to hold down the option key on your Mac while you click on the Wireless Mode selection box to get the WDS option to appear. (My guess here is that Apple "hides" it because it slows down the network substantially). But, it's the only way to do what you want to accomplish with and old and new device.
Other options would include the wireless card you mentioned for the iMac. Even better might be a pair of ethernet powerline adapters. One adapter goes near the AirPort Extreme and the other near the iMac. The AC wiring in your home transmits the ethernet signal of the powerline. Works great, almost no configuration required and better than wireless in many cases. -
Questions about setting up my network with my Mac Pro?
I'm trying to set up my network with my Mac Pro. I have two other roommates that need internet and a printer that we all need to access. The modem is with my Mac Pro in room 1, the printer is with another PC in room 2, and another PC with wifi is in room 3. What is the best way to connect all these.
My idea was to install an Airport card in my Mac Pro, then add an Airport Express station w/airtunes to room 2, to connect the PC and printer. That way, room 3 can access with wifi, and room 2 can physically plug into the Airport Express station. Problem with that is that the Airport Express Card must be professionally installed in my Mac Pro and that $80+ charge on top of the Airport Express and Aiport Card itself, turns this into a $200+ endeavor.
I also have a wireless Linksys router and Linksys WiFi USB receiver. Anybody have any other ideas?
Mac Pro Mac OS X (10.4.9)Your plan wouldn't work anyway. The Mac Pro can not create a WDS compatible wireless network. Therefore the AirPort Express (AX) can not use WDS to wirelessly join the network. Therefore the AX's Ethernet port will not be activated.
The best solution is to buy an inexpensive wireless router [or the AirPort Extreme base station (AEBS)]. Connect the Mac Pro via Ethernet to the router. Add a wireless adapter to the PC in room 2. Therefore the PCs will connect wirelessly while the Mac Pro connects via Ethernet. -
How to connect an apple tv to an enterprise network with a username and a password?
I need to use it over my university's wifi. theres no option to enter username and password. how to connect the apple tv to such enterprise network?Contact the University's IT dept, they may be able to set something up on the network to allow the ATV to connect without the need for a user name/password.
-
Setting up wireless network with 2x airport extreme ac
I've got a business customer with 2 new Airport Extreme 802.11 AC behind a comcast modem.
When the first extreme is set up, all is well.
When the 2nd Extreme is introduced, Airport Utility asks to automatically wirelessly extend the network, which I allow it to do.
But sometime during that setup, the 2nd extreme becomes unresponsive, and the connection to the internet becomes broken.
The only thing that restores it is to reboot the first Extreme. No matter how many times Iv'e done this, it results in the same problem. I've replaced Extreme #2 with a new one, and I get the same problem.
There are 20 some odd devices on the network; with one Extreme, it works great, and the Extreme AC's replaced 2 older version of Extreme's that were doing this just perfectly.
What is causing this problem, other than me doing something stupid, and how do I extend the network? I'd rather extend it with the wire it's connected to than wirelessly.Power off AirPort Extreme 2 for now and test the Ethernet cable that is connected from one of the LAN <-> ports on Extreme 1 by temporarily connecting the cable to the Ethernet port on a laptop or desktop. Turn off the wireless off on the computer and see if you can get a good Internet connection that way.
If you can, then you know that the Ethernet port on the AirPort and the cable are both working correctly.
If you can't, then you need to do some troubleshooting to identify the real problem before you can attempt to configure AirPort Extreme 2.
Post back when you have verified that you have a working connection between AirPort Extreme 1 and the device that you are using to test. -
Just bought new time capsule- need help setting up WiFi network with another router
Here ismy situation.
I had a wireless network setup up at home using a Belkin wifi router.
I have 2 macBooks (1 pro, 1 air) and 2 iphones that connect wirelessly and a desktop PC that is hard wired to the ethernet port. In addition, I have a Verizon wireless network extender plugged in by ethernet. All of the hard-wired gear is in our 3rd floor attic office (and the wireless signal was strong throughout the house).
The Belkin wifi router was plugged into a wall ethernet jack that is in turn wired into a Linksys router in the basement (along with multiple other ethernet ports througout the house) and is hardwired to the Cable modem next to it. All of the hard-wired ethernet stuff (including the router in the basement) was there when we bought the house, and I have no clue in the tangle of wires how to sort them out (but don't really think I need to)
I just purchased a TimeCapsule to do wireless backups of my 2 macbooks, and tried to set it up alongside the existing wireless modem.
Needless to say, this did not work well. I called AppleCare, and was told that the TimeCapsule needs to be the "1st" wireless adapter, so I went into the basement, and connected the time capsule directly to the cable modem, and then out to the basement router. The Belkin router still needs to be in the attic to supply the PC and the Verizon adapter (so it is near a window for GPS signal).
If I try to name the WiFi network the same SSID on both the TC and the belkin router (to have dual signal strenth coverage) the whole thing gets messed up and the TC cannot be "found" by the aiprort Utility software.
What I have done now is that I have 2 side-by-side wireless networks with 2 unique names (actually 3, because I enabled the 5Ghz signal on the TC), but our wireless devices do not "switch" automatically from one SSID to another stronger signal SSID as we move through the house
Here's the question: How do I name them the same so that the devices will switch effortlessly to the stongest signal? I understand it involves switching the "channels" but don't know how to do it right now. Currently, everything works, so I don't want to mess it up tinkering. Another caveat- there are several other wireless networks from neighbors houses that I can "see". I jsut downloaded a program called iStumbler that shows the channels, but not sure what to do with that info.
Any advice would be appreciated.Here's the question: How do I name them the same so that the devices will switch effortlessly to the stongest signal? I understand it involves switching the "channels" but don't know how to do it right now. Currently, everything works, so I don't want to mess it up tinkering. Another caveat- there are several other wireless networks from neighbors houses that I can "see". I jsut downloaded a program called iStumbler that shows the channels, but not sure what to do with that info.
Any advice would be appreciated.
OK.. sounds like a mess.. or at least messy and the previous people should have left a log book with all the IP address info in it.. you have far too many routers.. but from here it is impossible to tell how they are configured. Most are probably just setup as AP.
Naming rule for wireless.. Same SSID same security different channel.
SSID ie wireless name to work on the PC side should have no spaces and no special characters. TC name should also follow that rule. So the devices need to all set with fixed channels.
Don't worry too much about iStumbler and what is outside your house.. there isn't enough channels at 2.4ghz anyway. And you are going to need to use them all. There are only three non-overlapping channels. 1, 6, 11 so set each device to one of those channels. The TC should be as close as you can to where you normally use the MacBooks.. and turn on the 5ghz. You will have to leave it to automatic name so the Macbook can also roam across from 2.4 to 5ghz. But if you care to use a different name and force it onto 5ghz the speed is much better as long as you are in the same room.
Roaming is great in theory.. often in practice it just doesn't work.. you need to step in and turn off wireless and then turn it back on.. you can quickly see which router it is connecting to by hold down the option key when you click the airport fan in the top menu area.. and look at bssid.. you will have to figure out which number MAC address relates to which router.
Also do not be surprised if Lion gives you issues. It seems to often drop out and lose connection to the TC as a backup device even if internet is still working. -
New download of keynote files when changing wifi network with iPad
When i change the Wifi Network with my ipad3 (without 3G) it always starts to download the keynote, numbers and pages files from the iCloud. You can't open any file until its downloaded again, you just see the Folder and the file as a placeholder.
In my opinion this Akers totally no sense. I expect a synchronization between iPad and the iCloud like it woks with mail, kalender. Even dropbox just downloads the file you select for use. In my case I have 64 files only in keynote, created on the iPad and eaven without changing something it will re download all files from the iCloud before I can use them.
Anybodydid the same experience ?
Is this a bug or a really shh.... Feature?No that's not my experience, it's clearly not working as it should. Perhaps you should restore your iPad.
-
Can I do this using the Time Capsule. I am not tech, so bear with me. Can I get the iPad to connect wirelessly to the TC, which connects wirelessly to the Canon MP495? Or, can I connect/network the iPad to the iMac to print?
Either way, or if there is any other solution, I would appreciate if someone would walk me through it, or point me to a plain-speaking resource.
Thankyou.
Actually, one more: I would like to connect my HP laptop as well. I have heard this is not simple, but possible.You can create a wifi network with your TC, and you can join this network with your iPad. However, your printer does not support the AirPrint protocol, so you will not be able to print from your iPad, unless you load additional software.
These are the steps:
1. (You may have completed this step already) Set up your TC to create a wireless network. You can do this from AirPort Utility on your Mac or from the AirPort Utility App on your iPad (free download from the App Store).
2. From your iPad, go to settings / wifi and join the network.
3. Download the Canon iPhone App from the App store on your iPad
4. You can now print photos from your iPad to your Canon printer.
If you want full functionality, (not just photos), there is software for your Mac that makes your printer available to your iPad through AirPrint (Printopia). The downside is, you have to purchase it, and you have to have your Mac running when you want to print from your iPad.
Good luck! -
I have been trying for hours to extend my Extreme Gen 5 network with an Express Gen 2. But no matter what I do or try, it doesn't work. What does happen is my internet gets blocked somehow when the Express is online and looks like it's set up perfect and 'green' - but no internet connection for anything even though the Extreme is green and the modem is good. Once I disconnect the Express, everything is good again.
I've tried LAN, WAN, though a switch, direct connect, Extreme set to Extend the network, the Express set to be an extension. Most of the time I get an error trying to update the Express. But when it seems to be set up perfect, the entire house can't get to the internet. Just when it looks right, it is so wrong.
If anyone can give me exact steps (e.g., "...from the Base Station menu, select the Restore Default Setting option" vice "...just restore the defaults..."), I would greatly appreciate it. I'm left to the conclusion that the Express is faulty. I've been using Airport Utility 6.2 from Mountain Lion on one computer and Airport Utility 5.6.1 from Snow Leopard on another computer (the latter give more control while the former just want you to 'forget' the Express).I finally got it working. I was trying to set it up ethernet. My biggest mistake was when the new Express came on, I did not select 'Continue' - I went straight to manual thinking that I would get the most setup options in manual mode. So everything I initially tried always resulted in 'wireless'. Even when I would update or restore default settings, the Express would not completely restart. Or sometimes I would get an error. So most of the time I had to unplug it. So when it came back up, none of my changes were retained. But there were a lot of times when everything was green and appeared to be fine. But anytime the ethernet cable was plugged in, no more internet.
So here's the weird part. When I finally tried 'continue' (vice manual), I would get 4 options. One would be 'ethernet' extended. So I would select it, it gave me green lights, all looked good, and still the same problem. This is when I got frustrated. I thought I had exhausted all possible combinations.
But somehow when trying continue again after another restore, I only got 3 options. One was the same ethernet extended option (can't remember what the missing 4th one was). And this time it worked - it gave me the big green circle with the checkmark saying it was successful. I don't know what I did different, but I know now that it won't work if 4 options come up to choose from. It will work if only 3 options come up. And success if only verified by the big checkmark. Had anyone anywhere said the checkmark declaring success is validation, then maybe I wouldn't have gone down so many rabbit holes thinking it should have been successful.
As for which Airport Utility I prefer, 6.2 looks nice, but it would just ignore the Express and would want me to 'forget' it and would not let me edit it. Airport Utility 5.6.1 was the one that I ended up using the most and finally had success with. It still strikes me as odd that there is no manually way to pick ethernet, it can only be choosen following a 'restore defaults', and only from the 3-option list (the 4-option list had the same ethernet choice, but it no worky).
Thanks for the response. I really do appreciate it.
Aiport Extreme Gen5 - internet access and router
Airport Express Gen2 - connected via ethernet, extending my wireless
- configured while connect directly to the Extreme, but now on a switch (16-port hub)
Using Airport 5.6.1
1) Restore Defaults from Base Station menu
2) Following restart, Select Continue
3) Of the 3 option presented, select 'ethernet.... extend network...'
- if 4 options are present, may not work
4) Wait for the green circle with the big white checkmark.
5) Connected Express to the switch where a cable went to other end of house - works.
Dead-zone went from 2mbps to 24mbps.
I probably spent 4 hours chasing my tail in anger. The correct way took about 5 minutes total.
Thanks again. -
I have had my ipad retina for two and a half weeks but since the week end every time i connect to the wifi network it joins then disapears as soon as i open safari for example or just disappears at intermittent intervals....i have my iphone 4s connected to the same wifi network with no such problems.
I have tried resetting the network settings to no avail
Does anyone have any suggestions?
Many thanks in advanced.I have had my ipad retina for two and a half weeks but since the week end every time i connect to the wifi network it joins then disapears as soon as i open safari for example or just disappears at intermittent intervals....i have my iphone 4s connected to the same wifi network with no such problems.
I have tried resetting the network settings to no avail
Does anyone have any suggestions?
Many thanks in advanced. -
How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet
This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network" -
I am sharing my macbook pro over a network with windows 7, however through windows 7 I can access my whole computer instead of just the shared files!
Hi Sig,
The issue is that i only want the shared folders to be accessed through windows 7.
Whats the point otherwise to have shared folders?
thanks.. -
Hi,
I have an existing modem/router from my ISP that does DHCP and NAT with base IP 192.168.1.1 distributed in the wireless network. I use this wireless network for our private devices. I could turn off the DHCP server in this first router, but there isn't a separate setting to turn off NAT.
I want to connect my Airport Extreme (4th gen) to this existing router to create a separate wireless network for visiting guests, where IP addresses of 10.0.0.0 etc. are used. So I do not want to use the Airport Extreme in bridge mode, as I would like to keep the devices on the first network 'invisible' for those on the second network. (P.S. when connected in bridge mode, the Airport works well and can distribute a network with a different name from the first. It's just that I would feel more comfortable about our privacy if the Airport were to distribute a different IP range. False security, maybe?)
I've tried doing this by 'Sharing a public IP address' in Airport Utility's Internet tab, leaving TCP/IP's setting to 'via DHCP', setting DHCP addresses to start with 10.0.0.2 up to 200 with all else blank, and not using a standard host nor NAT-PMP in the NAT tab.
When I do this the Airport complains of a 'double NAT issue'. Internet connectivity seems to be OK, but when switching between the two networks on my Mac I get complaints about my IP address being in use by another device intermittently.
Can anyone help in how to get the 'double NAT issue' resolved?
Thanks!So if someone is connected to the modem/router network they will be able to see the HD I will have put in to the AirPort Extreme?
As I said above.....since the modem/router and AirPort are bridged, devices on the modem/router wireless will be able to "see" devices on the AirPort wireless, and vice versa.....
If they can see the HD connected to the AirPort Extreme, will they be able to access it
Yes, unless you plan to password protect the drive connected to the AirPort Extreme.
or will they still need the password needed to get onto the AirPort Extreme network?
The modem/router and AirPort Extreme are bridged. They are on the same network. All devices are on the same network when the modem/router and AirPort are bridged. Not sure how else that I can say this.
Also, because it is bridged, I shouldn't have any problems accessing the HD I will have connected to the AirPort Extreme from an external location?
Accessing devices from a remote location is never easy....and a topic for a different post/discussion. If you have a "static" Internet IP address from your provider, and have all the details on how to forward ports on your modem/router, you are off to a good start.
Apparently there is some addressing issues because devices can be seen as "Double IP" because the modem/router would have allocated IP's as well as the AirPort allocating IP's thus making connections slower until resolved
When you "bridge", all IP addresses are issued by one device. There will be no conflicts on the network, since they are bridged.
Once again, in very simple terms, you have two doors (access points) that open into the same room (network). One "door" is the modem/router and the other "door" is the AirPort Extreme. They are on the same network....("room") because they are bridged.
Maybe you are looking for
-
Customer Inbound Payment Advice
Hello all, What is the actual purpose of Payment Advices on the customers side (Inbound). Can somebody explain me how to post the customer payment advice in the SAP system? My assumption is below; please correct me where you see I am wrong Customer s
-
When you take a snapshot of the desk top where is it saved?
When you press Control-Command-3 for a snapshot where can I find it?
-
I'm not sure how this happened but it did. I have thousands of photos in iPhoto that are duplicates of other photos. Is there a way to have iPhoto scan through the photo library and delete all of the extra copies of photos? thanks, - Ernest
-
Titles don't fade in smoothly in Premiere CS6.
My titles sort of "pop" in instead of smoothly ramping up to full opactiy. I'm not a novice video editor and this should be very simple to do, but I can't get a super smooth title fade. Is there something special I need to do other than just use a
-
Hi! -- Plz describe me use of &p_where_clause parameter in Reports, why we use this & how we use this parameter. -- I am using Report 6i. Thanks !