New hard drive not working

I just bought a new hard drive to replace my exhausted 12G HD in my G3 iMac DV graphite. I started up using the original OS 9 disc and the HD was not recognized. I loaded OS9 onto the new HD via fire wire from my G5 successfully, still no joy. So here's the specs: Maxtor Ultra Series 100GB, 7200 rpm, Ultra ATA/133. I got it pretty cheap at Staples. The package info seemed to indicate this would work. If not compatible I guess I can add it to my G5. Thanks in advance. If this is the wrong drive....can I get the specs for what type of HD I should be looking for? Thanks.
MJC
G5 and iMac DV Graphite Mac OS X (10.3.9)
G% and iMac DV Mac OS X (10.3.9)

Do the following:
1, Boot from your OS X Installer Disk. After the installer loads select Disk Utility from the Installer menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
You should now be able to install OS X.

Similar Messages

Flashing Question mark: New hard drive not working Macbook Pro late 2008

After following several peoples advice on this forum I decided to upgrade my Macbook Pro late 2008 with a Seagate (1TB) Solid State Hybrid Drive 2.5 inch.
Heres the device.
http://www.morecomputers.com/spec.aspx?pn=ST1000LM014
After creating a mountable boot on a External hard drive with Mavericks install I removed the current hard drive and replaced with the new seagate drive. However it didn't seem to recognize the external hard drive (it is quite old but works perfectly) and went to a flashing grey question mark screen and wouldnt do anything else. Ive tried holding down command-r and option-r but I get nothing. Its just the same flashing question mark. I have done this several times and the same result.
I put the old drive back in and it works fine.
I am trying to work out is the problem with the mountable external hard drive OR is it the hard drive is not compatible with my computer?
Appreciate your help
Gary

Sorry I think you may be confused.
I am trying to install the new Seagate hard drive to my mac (not as an external hard drive).
I replace the macbook pro hard drive with the seagate drive:
http://www.morecomputers.com/spec.aspx?pn=ST1000LM014
I then started up the machine with a usb external hard drive with a boot copy of mavericks on it. However, it just displayed a flashing question mark and wouldnt start booting the osx.
I am trying to work out is the problem with the mountable external hard drive OR is it the hard drive is not compatible with my computer? Im guessing it must be hard drive. Would it be better to use a USB pen drive as the external hard drive is quite old?
Does anyone know what the problem could be as the hard drive is brand new.
Appreciate your help
Thanks, Gary

New Hard drive not working - please help!!!

This is an original thread that I'd started:
http://discussions.apple.com/thread.jspa?threadID=2066043&tstart=0
Since that, I tried the following this morning.
I took out the old 100GB drive and fitted the new 500GB (blank) drive. My plan was to fresh install OSX, install Carbon Copy Cloner and then clone the old drive by plugging it in with a reading device I have. What actually happened was the following:
I put in my Mac OSX install disc 1. I opened disc utility from the top toolbar. In disc utility the new drive showed up and I formatted (erase option) it to mac OS Extended (journalled). I then began a fresh install of OSX. As it started the macbook told me I was '+running on battery power+' and '+was I sure?+'. With full battery I said yes and continued. All was going well and it prompted for the second install disc. It got some way through that and then got stuck at 38% installing garage band loops. The new internal drive was also making a repetitive noise - not loud or anything but certainly sounded like it was searching for something. As the whole thing was stuck and nothing was working I held down the power button.
I tried again with the first disc but it wont even do anything anymore! I took out the new drive and put in the old one. Booted up. Connected the new drive to the reader with the idea of re-formatting it via disc utility.
But now the brand new drive is not readable and is making the a few funny repetitive noises.
Please help me someone - I'm very worried about this new drive now!!! Is is broken or corrupted or something???
Your help is very much appreciated
Adam

Vegas Superstar wrote:
My plan was to fresh install OSX, install Carbon Copy Cloner and then clone the old drive by plugging it in with a reading device I have.
Hi VS,
What "reading device" are you using?
As it started the macbook told me I was '+running on battery power+' and '+was I sure?+'. With full battery I said yes and continued.
It is best to have the power adapter connected when running a long process like this which cannot be interrupted.
The new internal drive was also making a repetitive noise - not loud or anything but certainly sounded like it was searching for something. As the whole thing was stuck and nothing was working I held down the power button.
How long was it "stuck?"
I tried again with the first disc but it wont even do anything anymore! I took out the new drive and put in the old one. Booted up. Connected the new drive to the reader with the idea of re-formatting it via disc utility.
But now the brand new drive is not readable and is making the a few funny repetitive noises.
Please help me someone - I'm very worried about this new drive now!!! Is is broken or corrupted or something???
It sounds like there is something amiss with the new HD. If you have access to a different external enclosure, (even on a PC, just to see if the HD will function), you could try erasing/formatting it again. If not, I think it's time to contact the vendor about a return.

Cannot get brand new hard drive to work. Disk utility states operation not supported when I try to erase or partition?

Without any success, I cannot get my hard drive to work in disk utilities. I am able to see the disk in the upper left hand column, but when trying to initiliaze the software always reads operation not supported. Any ideas?

You probably have too new a hard disk. Contact the hard disk manufacturer and ask what jumper setting is needed to drop to 1.5 Gbps SATA speed.
Either that, or return the disk, and go to http://www.macsales.com/
They can be sure to equip you with a proper hard disk.
Note formatting is key as well:
http://discussions.apple.com/docs/DOC-3003

Installed new internal hard drive, not working

Hello everyone. I have an iMac model # A1224. My hard drive crashed, therefore I purchased this one:
http://eshop.macsales.com/item/Hitachi/0S02860/
I have installed it and when I turn it on I get the gray screen with a blinking question mark. Anyone have any idea why it would do this with my new hard drive. Thank you.

Well, did you reinstall the operating system? If not, yes, you're going to get a blinking question mark, because the Mac doesn't have a system to boot from! You need to use your Mac's installation DVD or a newer retail version of OS X to either install a new clean system, or recover from any Time Machine backup you may have.
Matt

Time Machine Restore from Networked external hard drive - not working??

recap: hard drive failure on iMac. Took it to Genius folks, they installed a new hard drive with updated Leopard OSx on it.
I came home turned it on, selected "restore from time machine" feature. It finds my external hard drive (which is connected to an airport extreme via USB 2.0) My computer is connected via ethernet to the airport extreme.
I select the imac backup and up pops the login screen. I log in. Then I get the "Checking Time Machine Backup...." And it just keeps checking and checking. The external hard drive is making all sorts of noises, like it is working away, but it just keeps checking. Also have the spinning beach ball....
How long does this go on before we get on with it?

LOL.. didn't see your answer until now. I feel pretty good as I did exactly what you recommended. Thanks so much for taking the time to respond. I appreciate it.
Here's the rundown on what I did.
LOL. I see y'all didn't know what to do either!!
Well after puzzling for a bit I finally aborted the process. I tried connecting my hard drive directly to the computer - but then it would not recognize the backup on the external drive.
So finally, I rebooted using the install disk and selected utilities and restore and voila, we were in business.
Restore said it would take 16 hours and went to bed - 11am. Got up at 5 and it was complete (guess it really didn't take that long) So far, everything looks great!!!!!
Hope this helps someone out there.

Thunderbolt 2 external hard drive not working with Macbook Pro (early 2011)

Hi,
I'm new to this forum and I hope you guys can help me with this:
I've recently bought an external hard drive that works on Thunderbolt 2 (LaCie d2 3TB). When I connect the new drive to my Macbook Pro through the thunderbolt port, the drive isn't recognized. However, the drive works fine through a USB connection.
I thought that Thunderbolt and Thunderbolt 2 are compatible, however this doesn't seem to be the case. Maybe it's because the OS X / driver / firmware version that I'm working on that is not updated? I work on an early 2011 Macbook Pro: OS X Version 10.6.8 (Snow Leopard).
Thank you very much for your help!
Daniel

Hi danielsh6,
I recently bought the new Lacie Thunderbolt 2 D2 3TB and I had the same problem as you, i have a macbook pro early 2011, those support thunderbolt but many times there is a bug that doesn't let you connect any thunderbolt drives to your computer. The solution I found was installing this update:
Thunderbolt Firmware Update v1.0
Before doing this I would recommend you updating to mountain lion (not yosemite yet as there is still some glitches and more on preview's macbook pro's).
Hope this helped!
Forest

Mac OS X (10.4) Clone To New Hard Drive - Not Booting

Hello folks,
I have recently bought an iMac G3 Snow, w/ 500MHz processor. This things works well with Tiger installed, but has quite a noisy hard drive. I wish to replace the hard drive with a newer, faster, and quieter 30GB hard drive that I happen to have spare.
I had booted the iMac in "Target Disk Mode", fired up my Macbook Pro, and connected the two computers via Firewire. I had then made a successful image of the iMac's HDD using Disk Utility. I then removed and replaced the hard drive in the iMac, and proceeded to restore the image to the new hard drive using Disk Utility again, also via Target Disk Mode.
Upon successfully restoring the image, I rebooted the iMac, only to find that the iMac cannot find the appropriate boot files. (ie, Question-mark w/ Finder folder logo error).
Any help to fix this would be muchly appreciated.
Many thanks,
Andrew

Hi Jeff - many thanks for your help. Unfortunately, I am still unable to boot from a clone made with SuperDuper or Carbon Copy Cloner.
I'm starting to focus my troubleshooting toward the iMac, or hard drive itself. These are my thoughts, if anyone could suggest any other places to poke around for inquiry.
- the Maxtor 30GB replacement hard drive is being recognised successfully in Target Disk Mode by my Macbook Pro. This shows that the hard drive works correctly, and that the iMac can access all of the data on the hard drive. The hard drive is set to "Master".
- when creating clone in either SuperDuper, or Carbon Copy Cloner, the clone processes report that the final clone on the new hard drive will be 'bootable'. This is reiterated when I look for the 'information' on the one partition in Disk Utility.
I have also reset the PRAM and NVRAM and the Open Firmware, to no avail of the hard drive booting into Mac OS X.
I have looked into my Open Firmware settings to see whether there may be a setting to specifically direct the Mac's bootloader toward the "BootX" file on the hard drive. When querying the 'boot-device', the Open Firmware's response is "hd:,\\:tbxi" - is this the correct function to have?
When I purchased the iMac, the Tiger 10.4 PPC DVD/CDs were not included with the purchase. I'm trying my best to fix the problem without the discs if at all possible.
Any suggestions as to where I can go to help my mac boot into Mac OS X again would be muchly appreciated. Thanks.
- Andrew

New hard drive not detected.

Hello all -
I've spent the better part of the last hour searching this forum, and haven't been able to find a solution, so I hope you folks can help me out...
After five years of dutiful, uninterrupted service, the original internal hard drive on my G4 QuickSilver 867 finally went kaput. Everything I really need is backed up offsite, so when the Apple Store Genius told me I'd need to start over with a new hard drive, I wasn't really upset. The Genius informed me that they'd be happy to replace my hard drive and get me up and running again for nearly $300, but then leaned over the counter and said that to save a ton of money, I should really just run out to Best Buy, pick up a new ATA hard drive and pop it in there myself. I happily followed his instructions.
Now I have a new Samsung 80GB ATA hard drive in my machine (set to Master and properly connected), but when I boot to my OSX install DVD, the computer evidently cannot see the new Samsung drive. When it asks for a destination volume on which to install the OS, there are no options available to select.
In searching the forum, it seems like everyone with a similar problem was trying to 'add' a drive, so I'm not sure the other information applies to me (since I have no OS installed, I can't use Disk Utility). Please note that I'm starting from scratch here... Just one hard drive in the machine, straight out of the box.
If there's something really simple that I've failed to do, please forgive this novice and lend a hand! Thanks in advance for your help. It is very much appreciated.

Thanks for the input, Rodney! Unfortunately, I can't seem to figure out how to reformat it. Here's exactly how far I get...
1.) Boot up the computer to the OS Install DVD.
2.) Installer asks me what I wish my primary language to be. I select English and hit Continue.
3.) Installer shows OS description and tells me to hit Continue if I want to install. I click Continue.
4.) The license agreement comes up and I hit Continue and then Agree to move forward.
5.) I am asked to select a destination volume for the OSX installation. There are no options to select. The only button I can press is 'Back'. There is an 'Options' button as well, but it is ghosted.
Any ideas?

New hard drive not showing up in select a destination window of install

I just installed a 500G hard drive and went to install OS X leopard and the new drive isn't showing up in the destination pane. Do I have to format it first? It shows up under disc utilities. If I have to format it what format should I use there are a few listed (journaled, etc)

I have had a new hard drive installed. When I go to Disk Utilities and click on Info it shows that it the following:
Connection Bus: Serial ATA
Connection ID: Device 0
Partion Type: ApplePartionScheme
Total Capcity: 298.1 GB
Format: Mac OS Extended (journaled)
However, the drive does not show up to install the OS to. Where do I go from here?
Sunny

Why is my hard drive not working?

My hard drive stopped working suddenly. I was burning a disc and it only burned 1 image and quit. I tried putting a new disc in and it tried reading it and spit it out. It was a brand new blank DVD.

Have you done any troubleshooting such as restarting the computer and if so what were the results.

Hard drive not working? help!

Dear all,
i was using my laptop (HP G56 Notebook pc). i turned it off for about 10 minutes came back to it and turned it on and it came up with "Boot Device Not found" at the top, and under that it says "Please install an operating system on your Hard Dives".
I've gone into F2 (system Diagnostics). I've tried "Start up test" "Run in test" and even "Hard disk test" and it still comes up with all the same things. i have tried to use linux to see if i can get some of my files but i can't find the hard disk in my computer can someone please tell me whats wrong and if it's fixable of i need a band new hard drive? ^ it also comes up with "Hard disk - (3f0) and also befor this happend i was hearing random clicking noises coming from my hard drive i didn't really think nothing of it to be honest
thanks
This question was solved.
View Solution.

All symptoms indicate a dead hdd. Random clicking leading up to this was a warning.Since you are within warranty HP should just send you a new hdd>>Contact HP
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

New hard drive not appearing in iTunes, can't burn discs

Just got a new hard drive. iTunes does not see either of my Superdrives. Any ideas on how to "connect" iTunes with my drives again, or if that's necessary. I have checked out the Help info in the app and didn't find an answer. Thank you!

Hi:
What happens when you run the HDD diagnostics test in the BIOS?
It is doubtful the notebook's HDD will boot with W7 already installed on it from another PC unless it is the same model as yours.
Quite often that is what you get when you try booting from a HDD from another PC that already has Windows installed on it -- nothing at all.
Paul

New Hard Drive not seen in Bios F23, hp g42 281la

My old hard drive stopped working (couldnt even restore). I bought a new hard drive (the same) and bios F23 doesnt see it.
Please help to resolve the issue.
Thanks.
This question was solved.
View Solution.

Hi Ivan_Vasilyev,
I understand you are having issues with the BIOS on your HP G42-281LA Notebook. Here is a download for the updated BIOS Version F.27 ( which is the latest).
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-93590-1&cc=us&dlc=en&lc=en&...
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

New hard drive not booting osx from external

Hi guys, I currently installed a new hard drive into my macbook, and I tried holding down the alt//option key to try and boot osx from my external hard drive ((Connected through USB)) but nothing happens. My mouse cursor appears, but nothing shows up. I tried 5 minutes ago to make sure that I was actually able to boot to my external drive from my old hard drive, and it worked perfectly. But nothing shows up on this end. Any help or suggestions?
thanks!

any one have any insight?

New hard drive not working

Similar Messages

Maybe you are looking for