New Mac Pro and Apple Cinema Display

Warning, for those of you upgrading to the new Mac Pro and you plan on using your old Cinema Display, you will not get the maximum resolution out of the display. In fact, you only get 1650 x 800--which of course is way under utilizing install resources and on top of that not a great picture. Even using recommended set up (mini display to DVI adaptor) does not help. You need a Thunderbolt Display for best video performance. Unless someone out there knows a way to do this--be prepared also to buy a new display.

Turbostar, it is the Apple 30 inch cinema display. Yes it works but the max resolution is 1650 X 800 which while acceptable does not get me 2560 x 1600 which my D500 GBUs would deliver. The new Pro is optimized for a Thunderbolt display, I am using the correct  connection protocols as recommended by Apple on their web page for this system. There is a specific note in Apple support noted that Cinema displays will only  provide xxxx resolution on the new Mac Pro's. Corsair.

Similar Messages

  • New Mac Pro and LED cinema display

    Sorry if this has been asked before, I tried searching for it but none of the topics answered my question specifically enough.
    I have a 24" Apple LED Cinema Display purchased less than a year ago. Will it connect to a new Mac Pro and what happens to the power cable that's attached to the LED display?

    I have a 24" Apple LED Cinema Display purchased less than a year ago. Will it connect to a new Mac Pro
    Yes. All the standard cards that come in the Mac Pro have one Mini DisplayPort. The 24"LED display will plug into that.
    and what happens to the power cable that's attached to the LED display?
    It is not used if you don't have a MacBook.

  • 2008 Mac Pro and Apple Cinema Display 27"

    Is there some sort of adapter that would allow me to plug the new Apple Cinema Display 27" with a 2008 Mac Pro? Or what change would I have to make to be able to work this out?

    Adrian - did you end up getting an adapter and using it? I purchased the Atlona DVI to Mini DisplayPort Converter (AT-DP200) to connect my 2008 MacbookPro (with GeForce 8600M GT) to the new 27 in. Cinema display, and though it works, it looks a bit fuzzy in terms of resolution. Having read the response here about making sure it is a DUAL link converter, I was going to try to return it for the AT-DP400.
    Then I read another thread on here that seemed to indicate that the AT-DP400 would not work at all with the 2008 Macbook Pro.
    http://discussions.apple.com/thread.jspa?threadID=2585380&tstart=0
    So now I'm confused. Just wondering what your experience is, if you ended up with getting the display and converter.

  • New Mac Mini and Apple Cinema Display

    I have just upgraded my Mac (G5 PowerMac) to a new Mac Mini.  I am still using my Apple Cinema display - but I cannot not play all the purchased movies that I have on iTunes now...????

    Greg,
    Are these movies HD? If they are, you might be having a problem with HDCP which is copy protection that won't let you view movies if all of your equipment is not HDCP compliant, which probably is your Cinema display. I also have a late 2012 Mac mini with an older Apple 20" Cinema display and cannot watch HD itunes movies. You will have to watch in standard definition. Of course you might have  a different problem, but your question seemed similar with my situation. What is strange is that you were able to watch from your G5 Powermac. Maybe the power PC chip allowed viewing as opposed to intel chips, which I think intel created HDCP. Somebody on these boards probably has better answers then me ;-)
    Rob

  • Mac Pro 2008 Apple Cinema Displays are black and there are start up issues

    I have a Mac Pro 2008 Dual quad 2.8 GHz. I have two Apple Cinema Displays (graphics are the standard ATI Radeon HD 2600 – 2 dual link DVI. I have 4 2-GB RAM sticks (8 GB total).
    Neither of my displays are showing anything. Their power lights are on but they are completely black throughout the start up process. In addition when I try to boot up with both graphics cards installed, I get nothing – no beeps no chimes. If just one card is installed (either card in either slot) the computer beeps, chimes and makes the sounds of booting up, but not a flicker on the displays. RAM does not seem to be the issue as I have tried booting with several configurations of RAM sticks with no negative or positive effects. I tried booting up with Hard Drives 1 & 2 removed with no effect.  I have tried several different start up moods and have reset PRAM.
    My guess is that there is something wrong with the motherboard. Or is it possible that both graphics cards are bad?

    The "least intensive" thing you can do is hold down Alt/Option at Startup. Thsi invokes the all-in-ROM Startup Manager, which will light up the screen gray or blue, then attempt to draw an Icon for each potentially-bootable Volume attached (if any). It works as if in slow motion, so you must be patient. If no activity after about two minutes you may count that as a failure.
    The next most intensive is to attempt to boot from an incorruptible source of software, such as an Installer/Utilities DVD. This again uses the "one-size-fits-all" display driver, and attempts to load software off the DVD. The dark colored Apple is loaded off a drive -- it is not present inside your Mac.
    The next most intensive step is to attempt to boot into Safe Mode. This also uses the "one-size-fits-all" display Driver, and does a disk check as it starts up, adding five minutes to the startup time. It then drwas a login screen and deamds your username and password, even if you normally auto-login.

  • How do i connect my Fujitsu Tablet + mac Pro to Apple Cinema Display 23'?

    Dear Mac users
    thanks in advance for your help.
    I currently own:
    • Fujitsu T 4220 (tablet) – Mobile Intel 965 Express – 60 Hertz – goes up to 1680*1050 (guess SXGA) – (it has the following other supported resolutions: 1400*1050, 1280*1024, 1280*768, 1280*720, 1024*768, and 800*600)
    • Mac Pro
    • Apple Cinema Display 23’
    What I would like to do is, please refer to the jpeg posted on http://www.flickr.com/photos/34831802@N06/3234336204/, connect – at the same time – my tablet pc and my Mac Pro to the 23' Apple Cinema Display and switch (when I need) from tablet to MacPro using the same 23’ ACD. Top would be to be able to switch for one to the other while they’re both switched on. Usually on 2 pc’s with vga I’d use a switch A → B (in the jpeg it would be I → E) with a selector.
    Have been reading different posts such as: http://discussions.apple.com/thread.jspa?messageID=8000641&#8000641 or http://discussions.apple.com/thread.jspa?messageID=6530475&#6530475 or
    http://discussions.apple.com/thread.jspa?messageID=7417258&#7417258
    + others on the net and have (hopefully) understood that:
    a) from Vga to Dvi I need a converter such as Geffen’s or similar
    b) the problem with ACD 23’ is that it has only 3 resolutions: 1024*640, 1280*800 or 1920*1200
    In the attached image I guessed a connection in order to connect – at the same time – both the machines to the 23’ ACD:
    1) my fujitsu tablet (i in the image) has to be connected, with a Vga cable (h), to the Vga → Dvi converter (g).
    2) from the Vga → Dvi converter (g) I need to connecto to the Dvi switch (c)
    3) easier is connecting the Mac Pro (e), since I only need a Dvi cable (d) to connecto to the Dvi switch (c)
    4) the Dvi switch (c) will then be connected to the 23’ ACD with a Dvi cable
    Now, my questions are:
    a) is the solution described above (Vga cable (h) to the Vga → Dvi converter (g)) a good solution or should I use, instead, a docking statione that comes with a Fujitsu Port Replicator (FPCPR65) which has a 1 x DVI-D port?
    b) Given the 3 resolution accepted by the 23’ ACD (1024*640, 1280*800 or 1920*1200), I do not understand if I can use my tablet through a Vga to Dvi Converter and at which resolution (my tablet has the following other supported resolutions: 1680*1050, 1400*1050, 1280*1024, 1280*768, 1280*720, 1024*768, and 800*600).
    c) Is there a way, also using an external video card or converter, to bring my resolution from 1680*1050 to 1920*1200? (the 16:10 ratio is in fact the same = WXGA (1280x800), WXGA+ (1440x900), WSXGA+ (1680x1050), WUXGA (1920x1200)
    d) Talking about Vga → Dvi converter (g), am aware of the gefen product. Can you please list some others that might be good as well?
    e) And how about the DVI switch? Any will work? Any particular suggestion?
    Thank you very much for your help.
    If you have any other suggestion, please let me know.
    Regards,
    Emil

    Noone to help me?
    No ideas?
    Thanks,
    Emil

  • ATI Radeon 9800 Pro and Apple Cinema Display compatibility

    I'd like to buy an Apple Cinema Display for my 5-year-old Power Mac G5 with an ATI Radeon 9800 Pro, but I'm having trouble understanding what I can and can't hook up to my system.
    I was thinking of getting a 30" display, but the Apple Store says I need a Dual-Link DVI, which I don't think my graphics card supports, but the Store also says I need an ATI Radeon 9650 or better, which I imagine the 9800 Pro is.
    I've looked at the ATI site for data on the graphics card, but their online manual shows a completely different set of connections on the card. They show VGA and S-Video out ports that mine doesn't have.
    Does my ATI Radeon 9800 Pro have dual-link? If so, can I use the 30" display? If not, can I still use the 30" display?
    If I can't use the 30" display, are there any compatibility problems with the 23" Apple Cinema Display?

    The 9800 is faster than the 9650, but it doesn't have a dual-link DVI port.
    Make sure you were looking at the Mac section of ATI's site. PC and Mac versions of the same card may have different port configurations.
    AGP cards with dual-link DVI, starting with the fastest:
    ATI Radeon X800 XT 256MB (ADC, dual-link DVI) (Some reports of problems with Leopard)
    <http://www.welovemacs.com/0831xeghr.html>
    NVIDIA GeForce 6800 Ultra 256 MB (Two dual-link DVI)
    <http://www.welovemacs.com/6613332.html>
    NVIDIA GeForce 6800 GT 256 MB (Two dual-link DVI)
    <http://www.welovemacs.com/6613441.html>
    ATI Radeon 9650 XT (Single-link, dual-link DVI)
    <http://www.mac-pro.com/ATI-Radeon-9650-256MB-for-G5-661-3593?sc=2&category=42>
    ATI Radeon 9600 Pro PC & MAC Edition RoHS 256MB AGP (Single-link, dual-link DVI)
    <http://shop.ati.com/product.asp?sku=3170809>
    A 23" will work with any G5 card.

  • New Mac Pro and iMac as Display – Several Crashes

    Hello,
    I am using a new Mac Pro (late 2013, 3.5 6C) and are really happy with it. But I have one problem …
    Currently I am using an iMac 27" as a display via Apple Thunderbolt cable (original cable from Apple).
    But when I switch my displays via cmd+f2, my mac pro sometimes crashes. So I can switch back to my iMac always, without issues. But sometimes, when I want to switch back to my running Mac Pro (no screensaver etc.), I cannot switch back and the Mac Pro simply reboots.
    Any ideas what to do? I've sent a bug report to Apple already …

    The warranty entitles you to complimentary phone support for the first 90 days of ownership.
    If you bought the product in the U.S. directly from Apple (not from a reseller), you have 14 days from the date of delivery in which to exchange or return it for a refund. In other countries, the return policy may be different. If you bought from a reseller, its return policy applies.

  • Can a genuine Apple European cord for the new Mac Pro and the Thunderbolt display be ordered from Apple?

    The title says it all. When I move to Europe I know I can use adapter plugs, but I would feel more secure, considering the cost of my Apple equipment, using Apple European power cords.
    So, is it possible to order these parts from Apple?

    The computer-end will be a fairly standard IEC-13 plug:
    http://en.wikipedia.org/wiki/IEC_cord#C13.2FC14_coupler

  • I got a new Mac Pro and I am using my 30 inch cinema display.  It has been flickering grey sometimes and then will stay grey and I have to reboot... this is very annoying..help.  I have reset the pram and that seems to help for a bit but then it starts up

    I got a new Mac Pro and I am using my 30 inch cinema display.  It has been flickering grey sometimes and then will stay grey and lock up my computer and I have to reboot... this is very annoying..help.  I have reset the pram and that seems to help for a bit but then it starts up again...and please don't tell me to check for software updates:)

    I got a new Mac Pro and I am using my 30 inch cinema display.  It has been flickering grey sometimes and then will stay grey and lock up my computer and I have to reboot... this is very annoying..help.  I have reset the pram and that seems to help for a bit but then it starts up again...and please don't tell me to check for software updates:)

  • Best stand for MacBook Pro and Apple LED Display

    I am buying a MacBook Pro and Apple LED Display tomorrow. I want to have a two display setup, similar to what I have seen in the Apple Store. I believe they used a Griffin Elevator. I want to make sure of two things: that the stand is sturdy enough so that my laptop won't slide off of it and that I can adjust the stand/monitor so that the tops are level (so that moving my mouse from the laptop to monitor and back is smooth - i.e. the cursor doesn't jump up or down.
    I like the fact that I can use this setup to go mobile very quickly, but what about my direct Ethernet connection. I wish there were a stand/dock such that I could hook everything up to it and then just undock the entire machine.

    How did you solve the problem of closing the Macbook Pro when it was connected to the display and preventing it from going to sleep?
    I am thinking about buying one. When I went to the local Apple Store the tech guys told me that it would be necessary to keep the laptop open slightly when connecting it to the display. They said it was something to do with cooling. It didn't sound right to me. I'm sure that Apple didn't solely intend for the Cinema Displays to be used by Mac Pro and Mac Mini users.
    There must be a simple way to "dock" or connect a Mac laptop (Macbook Pro or Macbook) to an Apple Cinema display or any other display with DVI input while keeping the laptop closed with an external keyboard and mouse connected and still be able to use the SuperDrive.
    I'm very curious about how you handled this.
    All the best for now,
    Ambrose

  • Just got a new mac pro and can't manage to set a password and keep it.  It keeps telling me I have the wrong password.

    Just got a new mac pro and can't manage to set a password and keep it.  It keeps telling me I have the wrong password.  I want to start over and I can't even get back in to do this bc it won't take any of my passwords.  How can I start over completely?

    You got a new laptop? try asking there or in Lion forum.
    If it has Lion, use the Recovery Mode boot Command-R
    Use that to erase and reinstall - it has network install ability.
    Want MacBook Pro forum or Lion Community?
    MacBook Pro
    Lion Mac OS X Communities
    New, as in from Apple, it would have asked for full setup.
    Want to reset the password? (it is used then I'd wipe it clean and start over)
    How to run the Password Reset utility in OS X 10.7 Lion

  • New Mac Pro and Vram

    My new mac Pro has dual AMD FirePro D700 6144 MB but After Effects only sees 2 gigs of VRam in the preveiw menu.  Why is that?

    Hi shasho,
    This issue has been reported that After Effects unable to read full display memory on New MAC Pro and is showing 2GB of available memory how ever system is equipped with 2 Card with 3GB memory each. We are working on this issue on a priority basis.
    Regards,
    Vinay

  • I just opened my new Mac Pro and I have a USB keyboard, not a bluetooth -- it doesn't recognize the USB keyboard and I can't get past the "bluetooth keyboard pairing" screen.

    I just opened my new Mac Pro and I have a USB keyboard, not a bluetooth -- it doesn't recognize the USB keyboard and I can't get past the "bluetooth keyboard pairing" screen.

    What specific KB?
    Do you know it works?
    I set my 2103 nMP with an older (black) Apple USB KB and it worked fine

  • I have a new mac pro and can't get a side scroll bar.  What can I do to get this?

    I have a new mac pro and can't get a side scroll bar.  How can I get this?

    The scroll bar is now set to appear automatically when you start scrolling with a trackpad or scroll wheel mouse. If you are using an mouse without a scrolling device, you should change a setting.
    In System Preferences, click General, and in the Show Scroll Bars section, click the option for how you want it to work. If you want to see them all the time click "Always."

Maybe you are looking for