New RAM causing Kernel Panics?

Hi all ...
I've had two KPs in the last two weeks (the first and only KPs since purchasing the Mac Pro last August). Three weeks ago, I installed a 4x1GB kit from Transintl.com and all seemed well. The first thing I did was to run AppleJack/memtest overnight in single user mode and it reported the memory is fine. I've also never seen anything other than "OK" in System Profiler.
This would normally lead me to believe the RAM is fine but I think the two recent kernel panics say different.
From the first line of the panic log:
Wed May 2 17:32:07 2007
panic(cpu 0 caller 0x00684CC4): Uncorrectable Fbd memory error detected.
ferr = 20000000 , nerr == 00000000, fErrFat = 20000000 nErrFat == 00000000
This is a RAM-induced KP, right? Is there any way to tell which module is the culprit? (Again, ASP always reports all RAM is OK - I can post the rest of the log if necessary)
Also, the new 1 GB sticks run around 40ºF hotter than my 512s. Is 180º F / 82º C for a a 1 gig stick normal?
-phil

Thanks for the info, William.
From what you guys are telling me, it sounds like heat may definitely be an issue here. I swapped modules from the first to second slot on each riser, swapped risers and now the modules in the second slot are the hottest. A2 is currently 187º F! (machine has been running for about 20 minutes - the only thing open is Safari)
Looking at the modules on their edge, the heatsinks don't seem to be flush with the sticks from top to bottom. (think of an inverted V like this ... /|\, where the center pipe is the RAM module )
I don't know if that has anything to do with it but the 'sinks on my 512s from Apple and Crucial are flush top to bottom.
-phil

Similar Messages

HELP! New RAID causes Kernel Panics

Okay, I am pretty sure I did something stupid here, but I desparately need some help for the gurus.
I got the following to setup a RAID:
Rosewell R2 RAID/dual disk enclosure
2 WD Caviar 750 drives
I have:
Tempo SATA Express 34
MBP 2.33 GHz 2GB running Leopard
Here is what happened:
I put it all together and the MBP recognized each drive.
I went into the Dis Utility to use the RAID setup.
Set it to
Volume Format - Mac OS Extended (journaled)
RAID Type - Mirrored RAID Set
I dragged the two drives into the list and clicked "Create"
Then all heck broke loose.
I got a Kernel Panic as the grey curtain dropped.
I have tested the Express card separately with another eSATA and it works fine.
I have tested 1 of the two 750 drives in a different enclosure and I get the Kernal Panic. I still need to check the other drive and load a known good drive into the enclosure to test it, but I don't want to kill a good drive.
So I assume I did something really really stupid.... I usually read much more about these types of things before setting them up but I am traveling and brought this with me to work on as I traveled. Unfortunately, I have had somewhat limited access to the internet and been unable to find any discussions of a similar situation occurring.
PLEASE HELP or at least come up with some good explanations.
Thanks

I'm not familiar with RAID setups all that much (the only RAIDs I've ever set up have been my Drobo's, and those were zero-config), so excuse me if any of my questions or suggestions seem dumb.
Have you tried reformatting the drives individually then set the RAID up again (reformat in APM just to be safe)?
Instead of setting up the RAID in a normal session of OSX, how about booting into your install discs and do it from Disk Utility? (although you said you were traveling, so I don't know if you'd have those on hand - maybe a retail copy of Leopard?)
When I have drive problems, I usually follow this pattern:
1) Reformat and try again. If that fails, then
2) Reformat, this time writing the drive over with zeros (an option in Disk Utility, which I'm sure you're aware of). If that fails, then
3) Try doing the setup in a lower level setting (i.e. single user mode, safe mode, from the install discs, etc.), as it might be something in your setting that might be messing it up.
I'd also try the requisite stuff for system troubleshooting as well - run a Disk Repair and Permission Repair on your boot drive, and clean out caches and whatnot (Onyx is a good utility for this - http://www.titanium.free.fr/pgs/english.html).

Airport causing kernel panics and kp in safe boot.

Last week I got my first kernel panic in years. It happened while I was asleep and checking an extrenal drive for bad blocks with TechTool. It turns out that the drive indeed had bad blocks and found that the cpu was shut down when I awoke. I started up the computer and it wasn't able to stay on for more than 10 min max before the next kernel panic. I checked here for more advice on kernel panics and started to try to narrow the number of culprits. Everything was unplugged and still kp. Instaled a new drive with a week older system from Time Machine and still kp. Reset NVRAM and replaced pyhsical RAM and still kp. Removed the Airport Extreme card and still kp. Booted into Safe Mode after all of the previously mentioned and still kp. I'm now going to take the drive and swap it into another body that I have to see if the root is actually on the drive on the physical hardware of the cpu.
I was interested in this thread and read all of the links that jpl posted. Airport causing Kernel Panic (?) Jason then replied that it had been solved due to a "permissions problem" I wish he gave more info on what exactly he did to resolve the problem as it's been almost a week now without any work being done for me.
I've also noticed this very strange behavior that might shed some light onto the issue. When I open System Prefs and close the window there is a strange colored pattern that will always flash after the window has been closed. I tried to post it to my me page but for somereason it wouldn't play for me so there's that and the YouTube version too.
https://www.me.com/gallery/#100008/Prefs%20Screen
http://www.youtube.com/watch?v=2zrTt88YdBo
In addition when the computer has started up and the system loads. Checking Activity Monitor shows that there are 50 or more threads active for the the kernel_task. Inspecting this doesn't seem to show any useful information.
Finally here are a few of the recent crashes I hope that someone might be able to shed some light on this extremely frustrating problem for me.
Tue Oct 25 18:54:16 2011
panic(cpu 0 caller 0x000AE584): "Uncorrectable machine check: pc = 00000000000A388C, msr = 0000000000141000, dsisr = 42000000, dar = 0000000000272008\n" " AsyncSrc = 0000000000000000, CoreFIR = 0000000000000000\n" "     L2FIR = 0000000000000000, BusFir = 0000000080000000\n"@/SourceCache/xnu/xnu-1228/osfmk/ppc/trap.c:975
Latest stack backtrace for cpu 0:
      Backtrace:
         0x0009AD18 0x0009B6BC 0x00029DC4 0x000AE584 0x000AE804 0x000B22F8
Proceeding back via exception chain:
   Exception state (sv=0x2fc12c80)
      PC=0x000A388C; MSR=0x00141000; DAR=0x00272008; DSISR=0x42000000; LR=0x000A37C8; R1=0x2E947B40; XCP=0x00000008 (0x200 - Machine check)
      Backtrace:
0x00000000 0x000A09C8 0x0009E2EC 0x0006B3C0 0x0006C728 0x0003BE1C
         0x0029361C 0x0029364C 0x0030924C 0x000B24C8 0x00000000
   Exception state (sv=0x249dba00)
      PC=0x9195435C; MSR=0x0000F030; DAR=0x00272000; DSISR=0x42000000; LR=0x00001FA8; R1=0xBFFFFB00; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: PubSubAgent
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:37:58 PDT 2007; root:xnu-1228~1/RELEASE_PPC
Tue Oct 25 19:09:54 2011
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x00000000FFFFFFFF PC=0x0000000000040DE4
Latest crash info for cpu 0:
   Exception state (sv=0x3c19ca00)
      PC=0x00040DE4; MSR=0x00001030; DAR=0xFFFFFFFF; DSISR=0x40000000; LR=0x00040D94; R1=0x33B63D50; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x0293EA14 0x0004147C 0x0001EB60 0x00025960 0x000B264C 0x00000000
Proceeding back via exception chain:
   Exception state (sv=0x3c19ca00)
      previously dumped as "Latest" state. skipping...
   Exception state (sv=0x3297b500)
      PC=0x919419D8; MSR=0x0000D030; DAR=0x0073C000; DSISR=0x42000000; LR=0x91948900; R1=0xF00807A0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: mdworker
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:37:58 PDT 2007; root:xnu-1228~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): copyin/out has no recovery point
Latest stack backtrace for cpu 0:
      Backtrace:
         0x0009AD18 0x0009B6BC 0x00029DC4 0x000AEB88 0x000B22F8
Proceeding back via exception chain:
   Exception state (sv=0x3c19ca00)
      PC=0x00040DE4; MSR=0x00001030; DAR=0xFFFFFFFF; DSISR=0x40000000; LR=0x00040D94; R1=0x33B63D50; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x0293EA14 0x0004147C 0x0001EB60 0x00025960 0x000B264C 0x00000000
   Exception state (sv=0x3297b500)
      PC=0x919419D8; MSR=0x0000D030; DAR=0x0073C000; DSISR=0x42000000; LR=0x91948900; R1=0xF00807A0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: mdworker
Wed Oct 26 15:31:02 2011
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x00000000FFFFFFFF PC=0x0000000000040DE4
Latest crash info for cpu 0:
   Exception state (sv=0x3c19ca00)
      PC=0x00040DE4; MSR=0x00001030; DAR=0xFFFFFFFF; DSISR=0x40000000; LR=0x00040D94; R1=0x33B63D50; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x0293EA14 0x0004147C 0x0001EB60 0x00025960 0x000B264C 0x00000000
Proceeding back via exception chain:
   Exception state (sv=0x3c19ca00)
      previously dumped as "Latest" state. skipping...
   Exception state (sv=0x3297b500)
      PC=0x919419D8; MSR=0x0000D030; DAR=0x0073C000; DSISR=0x42000000; LR=0x91948900; R1=0xF00807A0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: mdworker
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:37:58 PDT 2007; root:xnu-1228~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): copyin/out has no recovery point
Latest stack backtrace for cpu 0:
      Backtrace:
         0x0009AD18 0x0009B6BC 0x00029DC4 0x000AEB88 0x000B22F8
Proceeding back via exception chain:
   Exception state (sv=0x3c19ca00)
      PC=0x00040DE4; MSR=0x00001030; DAR=0xFFFFFFFF; DSISR=0x40000000; LR=0x00040D94; R1=0x33B63D50; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x0293EA14 0x0004147C 0x0001EB60 0x00025960 0x000B264C 0x00000000
   Exception state (sv=0x3297b500)
      PC=0x919419D8; MSR=0x0000D030; DAR=0x0073C000; DSISR=0x42000000; LR=0x91948900; R1=0xF00807A0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: mdworker
Wed Oct 26 22:17:42 2011
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000010 PC=0x0000000000082EF8
Latest crash info for cpu 0:
   Exception state (sv=0x2514ea00)
      PC=0x00082EF8; MSR=0x00009030; DAR=0x00000010; DSISR=0x40000000; LR=0x00082ECC; R1=0x24F6BB60; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x00000000 0x000848C0 0x00077BD0 0x0007823C 0x0007920C 0x0006B718
         0x0006C728 0x00296378 0x0030924C 0x000B24C8 0x00000000
Proceeding back via exception chain:
   Exception state (sv=0x2514ea00)
      previously dumped as "Latest" state. skipping...
   Exception state (sv=0x2509d500)
      PC=0x9194AF64; MSR=0x0000D930; DAR=0xE1000000; DSISR=0x42000000; LR=0x9194CC90; R1=0xBFFFE9A0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: launchd
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:37:58 PDT 2007; root:xnu-1228~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
      Backtrace:
         0x0009AD18 0x0009B6BC 0x00029DC4 0x000AEA90 0x000B22F8
Proceeding back via exception chain:
   Exception state (sv=0x2514ea00)
      PC=0x00082EF8; MSR=0x00009030; DAR=0x00000010; DSISR=0x40000000; LR=0x00082ECC; R1=0x24F6BB60; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x00000000 0x000848C0 0x00077BD0 0x0007823C 0x0007920C 0x0006B718
         0x0006C728 0x00296378 0x0030924C 0x000B24C8 0x00000000
   Exception state (sv=0x2509d500)
      PC=0x9194AF64; MSR=0x0000D930; DAR=0xE1000000; DSISR=0x42000000; LR=0x9194CC90; R1=0xBFFFE9A0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: launchd
Thu Oct 27 11:28:35 2011
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000000000004 PC=0x00000000000848E0
Latest crash info for cpu 0:
   Exception state (sv=0x248ff500)
      PC=0x000848E0; MSR=0x00009030; DAR=0x00000004; DSISR=0x42000000; LR=0x000848AC; R1=0x30063BB0; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x000848C0 0x00077BD0 0x0007823C 0x0007920C 0x0006B718 0x0006C728
         0x00296378 0x0030924C 0x000B24C8 0x00000000
Proceeding back via exception chain:
   Exception state (sv=0x248ff500)
      previously dumped as "Latest" state. skipping...
   Exception state (sv=0x248fd280)
      PC=0x9194AF64; MSR=0x0000D030; DAR=0xE1000000; DSISR=0x42000000; LR=0x9194CC90; R1=0xBFFFE7F0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: launchd
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:37:58 PDT 2007; root:xnu-1228~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
      Backtrace:
         0x0009AD18 0x0009B6BC 0x00029DC4 0x000AEA90 0x000B22F8
Proceeding back via exception chain:
   Exception state (sv=0x248ff500)
      PC=0x000848E0; MSR=0x00009030; DAR=0x00000004; DSISR=0x42000000; LR=0x000848AC; R1=0x30063BB0; XCP=0x0000000C (0x300 - Data access)
      Backtrace:
0x000848C0 0x00077BD0 0x0007823C 0x0007920C 0x0006B718 0x0006C728
         0x00296378 0x0030924C 0x000B24C8 0x00000000
   Exception state (sv=0x248fd280)
      PC=0x9194AF64; MSR=0x0000D030; DAR=0xE1000000; DSISR=0x42000000; LR=0x9194CC90; R1=0xBFFFE7F0; XCP=0x00000030 (0xC00 - System call)
BSD process name corresponding to current thread: launchd
Thanks in advance,
Max

My vision is pretty poor, still cant see it, but...
At this point I think you should get Applejack...
http://www.macupdate.com/info.php/id/15667/applejack
After installing, reboot holding down CMD+s, (+s), then when the DOS like prompt shows, type in...
applejack AUTO
Then let it do all 6 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 6 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
Trash old Log files.
First reboot will be slower, sometimes 2 or 3 restarts will be required for full benefit... my guess is files relying upon other files relying upon other files! :-)
Disconnect the USB cable from any Uninterruptible Power Supply so the system doesn't shut down in the middle of the process.

External LaCie Multi Recorder causing kernel panics since reloading OS

I just replaced my main internal hd with a new 1TB WD Caviar Black. I migrated all of my user information from my old drive via Time Machine & all seemed well. Since I did a fresh, zero out data install of the OS on the new drive, I need to reinstall my programs. Some of my older programs are kept on DVD-RAM disks that I've had since my old G4. To access these files I use my LaCie Multi recorder which was working fine prior to the HD switch.
When I put my DVD-RAM disk into the drive it's now causing kernel panics.
Anyone know what could have caused this or how I might correct the problem?
Thanks.

Okay, it seems that I've got a bad disk. I connected the drive to my laptop & used another dvd & all worked as it should. Put my program back-up disk in & it caused a panic.
New question, is there any way to repair the disk?
I've got DiskWarrior & TechTool Deluxe but I'm not sure how I might go about the repair as the panic occurs while the drive is trying to access the disk.

Using 2 memory modules causes kernel panic

In early 2009 I upgraded my memory from 512 to 2 GB, 2 modules of 1GB each. This past January (just shy of 2 years later) I got a kernel panic. I tested running with a single module, and one module caused panic, the other was fine. Both slots function with the good module. So I got two new matched replacement chips from OWC, put them in and got kernel panics during the boot process. Yesterday I spent testing memory configurations and found this:
1. chip 1 alone runs fine and passes all Rember memory tests in slot 1.
2. chip 2 alone runs fine in slot 1 and 2, passes all memory tests in slot 2.
3. chips 1 and 2 together, in either slot, cause kernel panics before the OS is loaded.
Has anyone seen this problem? Will it go away if I use top of the line (Apple) memory chips?
When the kernel panics started back in January, an AppleCare advanced advisor said he had the same problem and he had to remove one module to stop the kernel panics. Running on 1GB doesn't work for me because I tend to max out the memory and programs like Mail, Safari, Photoshop, etc. become unreponsive all together.
thanks -

I have spent more time on the phone with OWC about this than I care to remember. Their latest request is that I use an eraser to clean the metal contacts on the chips; if that fails, I get to send the chips back. Whether I get a refund or yet another set of replacement chips, I don't know. They are not experts on Apple machines, that is clear.

RAID mirror with software utility caused kernel panic every time

Using disc utility to make a mirror of 2 drives, click create and i get kernel panic and have to power off machine. if i try to start the machine with either of the two disks in it (together or individually) i get same kernel panic and have to power off.
The disks are in an external storage array (sonnet d500). I have a second storage array with raided disks in and i have raided disk inside the mac too. these all work fine..
originally 2 weeks ago i had the 2 disks working in a group of 4 disks set as a mirror of 2 striped disks. One disk in this setup failed and with this config you can never 'recover'or rebuild it - you get a degraded mirror and you can backup the data, but you must completely rebuild the raid again as the mirror of stripes never lets you add a new disk in again.period. not good.
I replaced the failed disk and rebuilt the mirror of stripes. this lasted a day until a second disk failed (all 4 were bought at same time so i was kind of expecting that to happen once one failed).
i replaced the second faulty hdd and thought about my disk usage and decided i would not make another mirror of stripes and i would make 2 mirrors instead for safe-ish storage and then transfer data to a striped raid set for editing from instead of direct from the mirror of stripes volume.
i tried to delete the raid but got a kernel panic
if i started the machine with any of the 4 disks i would get a kernel panic.
i moved the disks one by one into an older G5 running Tiger and managed to erase the raid info on 2 of them. The two new ones had some strange raid info and the Tiger machien thought there was an extra disk in the machine and would not erase or partition or allow me to destroy the raid whatever i tried.
I will be moving these now into an old XP PC to try to erase the boot records etc and erase them to be able to use them again in either mac pro or G5. painful..
so.. i ended up with 2 erased drives and have 2 new drives with dodgy raid info that causes kernel panics on the leopard machine and wont go in the Tiger machine.
The two erased drives are what ive now been trying to use in the mac pro to create a mirror - this now caused kernel panics when creating the mirror to start with and when installed in the machine at all. so i will be erasing them again in the tiger machine soon (its busy erasing with zeros another new disk that i added to the Tiger machine 2 weeks ago which seems to have some fault when raided!!! but thats another story).
so.. is anyone else having problems with creating basic mirror in 10.5.4 or is it just me??
i have a sonnet tempo e4p card with 2 external sata disk enclosures, latest firmware for the e4p card. all other previously existing raid volumes are working fine. i have one set of 2 striped disks, one set of 3 striped disks and one set of 2 stripes which are mirrored - all happy and working fine. but i cant make a new mirror of 2 disks...
I phoned Apple support and they said all raid info was kept on the disk itself and nothing on the actual machine and suggested i take the machine to an apple care centre for some tlc (although its disk i am having a problem with). since all my other disk arrays work fine i don't really want to rebuild the whole machine from scratch if i can avoid it.
Any suggestions of what i can try ??

well it turns out the new disk i bought just werent any good. my g5 powermac raid mirror issue was related to one new disk with lots of bad blocks (speed tools showed that up) so i have learnt my lesson on cheap non raid disks for raid..
am waiting on a couple of new ultrastar enterprise disks to tuen up so i can go back to the macpro and try to add a mirror again.
i am still stuck wih several new disks that i cannot format now in the macpro on leopard or on the g5 powermac with tiger.
ive tried softraid and that cant do it, speedtools pcformat util cant do it, disk utility crashes when i try to eras them and diskutil from termianl starts then doenst get anywhere and my pc sata card doesnt work so my last resort pc option still doesnt help me clear the partition map on these drives - ones that diskutility on leopard made for me - and drives which still cause kernel panics on the macpro if i put them in it..
here is what diskutil says on my g5:
/dev/disk0
#: type name size identifier
0: GUIDpartitionscheme *465.8 GB disk0
1: EFI 200.0 MB disk0s1
2: Apple_RAID 465.4 GB disk0s2
3: Apple_Boot 128.0 MB disk0s3
/dev/disk1
#: type name size identifier
0: Applepartitionscheme *233.8 GB disk1
1: Applepartitionmap 31.5 KB disk1s1
2: Apple_HFS Macintosh HD 233.6 GB disk1s3
/dev/disk2
#: type name size identifier
0: *465.4 GB disk2
/dev/disk3
#: type name size identifier
0: Applepartitionscheme *931.5 GB disk3
1: Applepartitionmap 31.5 KB disk3s1
2: Apple_HFS backup1T 931.4 GB disk3s3
/dev/disk4
#: type name size identifier
0: Applepartitionscheme *931.5 GB disk4
1: Applepartitionmap 31.5 KB disk4s1
2: Apple_HFS tempi 931.4 GB disk4s3
disk0 is the one with the bad partition info.
it thinks it has a double raid as the console shows on startup:
(both store45 and cache it thinks are on this disk - cache was my old mirror of stripes set on other machine, store45 was new name for my mirror, so seems like it hadnt deleted the original raid partition info before making new info which now kernel panics)
Jul 18 18:48:05 localhost kernel[0]: AppleRAID::degradeSet - starting the set "STORE45" (B9C48619-6B2C-4547-A01E-4864754EA7E2).
Jul 18 18:48:35 localhost kernel[0]: AppleRAID::degradeSet - starting the set "CACHE" (64F914A5-5556-4A44-AEE2-DC437868766B).
Jul 18 18:48:35 localhost kernel[0]: AppleRAID::completeRAIDRequest - error 0xe00002c2 detected for set "STORE45" (C0E139A4-2A6D-49C6-8F77-202AF7F9285D), member 50207BE5-E487-410E-8E8E-C4C4DCD2687B, set byte offset = 999527018496.
Jul 18 18:48:35 localhost kernel[0]: AppleRAID::completeRAIDRequest - error 0xe00002c2 detected for set "CACHE" (64F914A5-5556-4A44-AEE2-DC437868766B), member C0E139A4-2A6D-49C6-8F77-202AF7F9285D, set byte offset = 999527018496.
so currently i have 2 new 500gb disks which cant be partitioned back to anything at all on either machine. looks like i will have to buy a new pc to reformat them..
any suggestions of how to clear the partition map info and get them back to freespace ??

Scanner Causing Kernel Panics

I have an old Agfa SnapScan 1212u USB scanner and up until today it has worked fine. Then suddenly it started causing Kernal Panics. It happens about 30% of the time. It scans the first 10% then throws up the Kernel Panic message and I'm forced to restart. I have run the Disk Repair Utility, repaired permissions, reinstalled the Agfa Scanwise driver, deleted all scanner related preferences and disconnected all other USB devices but nothing seems to work. The only software update I've done recently is the August and Java Security updates. Could either of these things be the problem? This is the first time I've had Kernel Panics on my Mac Mini. I doubt it's caused by the ram. It has worked flawlessly since I put in the 1GB module in July.
Does anyone have any ideas?
Cheers
djon

Well, I downloaded Vuescan and set it up but now I have another problem. Vuescan constantly crashes. Sometimes it crashes when I'm changing settings and sometimes is crashes after a scan. I set the memory settings very high so it shouldn't be a memory issue. I've tried just about everything to get this scanner working with Vuescan. I even installed a fresh copy of Panther on my Firewire drive but it only reduced the crashes not eliminate them. I'd like to get Vuescan working because it seems to make better scans than Scanwise did. At least it doesn't cause Kernel Panics. Does anyone have any idea what's going on? I'm beginning to think that it might be a hardware problem with the scanner.
djon

Battery Update Causing Kernel Panics?

It seems that ever since I installed the Battery Update it's been causing Kernel Panics on my MBP. Three since yesterday in fact. Has anyone else been experiencing this?
MacBook Pro 1.83 GHz Mac OS X (10.4.9) 1 GB RAM, 80 GB HDD, ATI Radeon X1600

Hmm I have seen multiple posts on the computer not booting the OS (gets to the grey apple with spinning gear screen) but so far I think you are the first I have seen reporting kernel panics.
Can you boot to the install cd? I'd try running the disk utility from the install disk and verify/repair permissions and verify the disk as well. (repair disk if verification fails)
Here is an article that may help ya:
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
http://docs.info.apple.com/article.html?artnum=106214

Readynas duo mounted over ethernet causes kernel panics

I've found out what is causing kernel panics on my machines, but i'm not sure how to resolve it. I have a g4 laptop and a new mac mini, both mount the readynas via mount_afp using a LoginHook. When the laptop or the mini go to sleep, the ethernet connection is powered off and at some point the readynas goes to sleep as well. So, when the laptop/mini wake from sleep, they have trouble re-establishing the mount to the readynas (as it needs time to spin it's drives up) and then the laptop/mini kernel panic...shouldn't this really be just a lost connection message, rather than a full fledged panic!

This is where we have a difference of opinion...If i can mount an external box over ethernet/firewire/usb and it causes the machine to kernel panic, then the software is not robust enough to handle the exception cases. Running 10.4.x for years with the same external hardware never yielded such results.

PS Extended CS6 causing kernel panics

I've been getting one or two a week. Haven't figured out yet what triggers it, but it only happens in CS6. I did recently reinstall the entire OS, so that's clean. Here's the latest panic info the reboot generates to send to Apple. Doesn't mean anything to me, other than the panic notation near the top of the info tells you what it thinks happened.
Interval Since Last Panic Report: 141469 sec
Anonymous UUID:                    44199F46-5B6B-42C5-9E13-29CB09291223
Mon Sep 24 14:40:11 2012
panic(cpu 2 caller 0xffffff80002094e7): "thread_invoke: preemption_level -1, possible cause: unlocking an unlocked mutex or spinlock"@/SourceCache/xnu/xnu-1504.15.3/osfmk/kern/sched_prim.c:1471
Backtrace (CPU 2), Frame : Return Address
0xffffff8149e83d70 : 0xffffff8000204d15
0xffffff8149e83e70 : 0xffffff80002094e7
0xffffff8149e83ef0 : 0xffffff8000209acb
0xffffff8149e83f60 : 0xffffff800053b02d
0xffffff8149e83fa0 : 0xffffff80002c8527
BSD process name corresponding to current thread: kernel_task
Mac OS version:
10K549
Kernel version:
Darwin Kernel Version 10.8.0: Tue Jun 7 16:32:41 PDT 2011; root:xnu-1504.15.3~1/RELEASE_X86_64
System model name: MacPro5,1 (Mac-F221BEC8)
System uptime in nanoseconds: 26760035257178
unloaded kexts:
com.apple.iokit.IOFireWireSBP2          4.0.6 (addr 0xffffff7f80e4a000, size 0x73728) - last unloaded 25651433036012
loaded kexts:
com.aladdin.kext.aksfridge          1.0.2
com.dvdfab.kext.fabio          1
com.hzsystems.terminus.driver          4
com.microsoft.driver.MicrosoftKeyboardUSB          8.2
com.microsoft.driver.MicrosoftKeyboard          8.2
com.Logitech.Control Center.HID Driver          3.6.0
com.apple.filesystems.afpfs          9.7.1 - last loaded 23445647212129
com.apple.nke.asp_tcp          5.0
com.apple.driver.AppleHWSensor          1.9.3d0
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.driver.AGPM          100.12.31
com.apple.driver.AppleUpstreamUserClient          3.5.7
com.apple.driver.AppleMCCSControl          1.0.20
com.apple.driver.AppleMikeyHIDDriver          1.2.0
com.apple.kext.ATIFramebuffer          6.3.6
com.apple.driver.AppleHDA          2.0.5f14
com.apple.driver.AppleMikeyDriver          2.0.5f14
com.apple.driver.AudioAUUC          1.57
com.apple.filesystems.ntfs          3.4
com.apple.ATIRadeonX3000          6.3.6
com.apple.filesystems.autofs          2.1.0
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.AudioIPCDriver          1.1.6
com.apple.driver.ACPI_SMC_PlatformPlugin          4.7.0a1
com.apple.driver.AppleLPC          1.5.1
com.apple.iokit.IOAHCIBlockStorage          1.6.4
com.apple.iokit.SCSITaskUserClient          2.6.8
com.apple.BootCache          31.1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.driver.AppleFWOHCI          4.7.3
com.apple.driver.AppleUSBOHCI          4.2.0
com.apple.driver.AppleUSBHub          4.2.4
com.apple.driver.AirPortBrcm43224          428.42.4
com.apple.driver.AppleAHCIPort          2.1.7
com.apple.driver.Intel82574L          2.1.8b1
com.apple.driver.AppleUSBEHCI          4.2.4
com.apple.driver.AppleUSBUHCI          4.2.0
com.apple.driver.AppleEFINVRAM          1.4.0
com.apple.driver.AppleRTC          1.3.1
com.apple.driver.AppleHPET          1.5
com.apple.driver.AppleACPIButtons          1.3.6
com.apple.driver.AppleSMBIOS          1.7
com.apple.driver.AppleACPIEC          1.3.6
com.apple.driver.AppleAPIC          1.4
com.apple.driver.AppleIntelCPUPowerManagementClient          142.6.0
com.apple.security.sandbox          1
com.apple.security.quarantine          0
com.apple.nke.applicationfirewall          2.1.14
com.apple.driver.AppleIntelCPUPowerManagement          142.6.0
com.apple.driver.AppleProfileReadCounterAction          17
com.apple.driver.DspFuncLib          2.0.5f14
com.apple.driver.AppleProfileTimestampAction          10
com.apple.driver.AppleProfileThreadInfoAction          14
com.apple.driver.AppleProfileRegisterStateAction          10
com.apple.driver.AppleProfileKEventAction          10
com.apple.driver.AppleProfileCallstackAction          20
com.apple.iokit.IONDRVSupport          2.2.1
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.kext.ATI5000Controller          6.3.6
com.apple.kext.ATISupport          6.3.6
com.apple.iokit.IOFireWireIP          2.0.3
com.apple.iokit.IOSurface          74.2
com.apple.iokit.IOBluetoothSerialManager          2.4.5f3
com.apple.iokit.IOSerialFamily          10.0.3
com.apple.iokit.IOAudioFamily          1.8.3fc2
com.apple.kext.OSvKernDSPLib          1.3
com.apple.driver.AppleHDAController          2.0.5f14
com.apple.iokit.IOGraphicsFamily          2.2.1
com.apple.iokit.IOHDAFamily          2.0.5f14
com.apple.iokit.AppleProfileFamily          41
com.apple.driver.AppleSMC          3.1.0d5
com.apple.driver.IOPlatformPluginFamily          4.7.0a1
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.BroadcomUSBBluetoothHCIController          2.4.5f3
com.apple.driver.AppleUSBBluetoothHCIController          2.4.5f3
com.apple.driver.IOBluetoothHIDDriver          2.4.5f3
com.apple.iokit.IOBluetoothFamily          2.4.5f3
com.apple.iokit.IOUSBHIDDriver          4.2.0
com.apple.driver.AppleUSBMergeNub          4.2.4
com.apple.driver.AppleUSBComposite          3.9.0
com.apple.driver.XsanFilter          402.1
com.apple.iokit.IOSCSIMultimediaCommandsDevice          2.6.8
com.apple.iokit.IOBDStorageFamily          1.6
com.apple.iokit.IODVDStorageFamily          1.6
com.apple.iokit.IOCDStorageFamily          1.6.1
com.apple.iokit.IOFireWireFamily          4.2.6
com.apple.iokit.IOAHCISerialATAPI          1.2.6
com.apple.iokit.IOSCSIArchitectureModelFamily          2.6.8
com.apple.iokit.IO80211Family          320.1
com.apple.iokit.IOUSBUserClient          4.2.4
com.apple.iokit.IOAHCIFamily          2.0.6
com.apple.iokit.IONetworkingFamily          1.10
com.apple.iokit.IOUSBFamily          4.2.4
com.apple.driver.AppleEFIRuntime          1.4.0
com.apple.iokit.IOHIDFamily          1.6.6
com.apple.iokit.IOSMBusFamily          1.1
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          6
com.apple.driver.DiskImages          289.1
com.apple.iokit.IOStorageFamily          1.6.3
com.apple.driver.AppleACPIPlatform          1.3.6
com.apple.iokit.IOPCIFamily          2.6.5
com.apple.iokit.IOACPIFamily          1.3.0
Model: MacPro5,1, BootROM MP51.007F.B03, 6 processors, 6-Core Intel Xeon, 3.33 GHz, 16 GB, SMC 1.39f11
Graphics: ATI Radeon HD 5770, ATI Radeon HD 5770, PCIe, 1024 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8E), Broadcom BCM43xx 1.0 (5.10.131.42.4)
Bluetooth: Version 2.4.5f3, 2 service, 12 devices, 1 incoming serial ports
Network Service: Ethernet 2, Ethernet, en1
PCI Card: pci104c,823f, sppci_ieee1394openhci, Slot-3@6,0,0
PCI Card: pci1033,35, sppci_usbopenhost, Slot-3@8,0,0
PCI Card: pci1033,e0, USB Enhanced Host Controller, Slot-3@8,0,1
PCI Card: pci1033,35, sppci_usbopenhost, Slot-4@11,0,0
PCI Card: pci1033,35, sppci_usbopenhost, Slot-4@11,0,1
PCI Card: pci1033,e0, USB Enhanced Host Controller, Slot-4@11,0,2
PCI Card: ATI Radeon HD 5770, sppci_displaycontroller, Slot-1
Serial ATA Device: HL-DT-ST DVD-RW GH61N
Serial ATA Device: HL-DT-ST BD-RE GGW-H20L
Serial ATA Device: WDC WD1001FALS-41Y6A1, 931.51 GB
Serial ATA Device: Hitachi HDS722020ALA330, 1.82 TB
Serial ATA Device: WDC WD3200AAKS-00VYA0, 298.09 GB
USB Device: Hub, 0x0409 (NEC Corporation), 0x005a, 0xfd300000 / 2
USB Device: EIZO USB HID Monitor, 0x056d (Eizo), 0x0002, 0xfd330000 / 3
USB Device: USB 2.0 Hub [MTT], 0x1a40 (TERMINUS TECHNOLOGY INC.), 0x0101, 0x40400000 / 2
USB Device: HASP4 USB 1.33, 0x0529 (Aladdin Knowledge Systems), 0x0001, 0x00200000 / 3
USB Device: SII Smart Label Printer 200, 0x0619 (Seiko Instruments Inc.), 0x0104, 0x00100000 / 2
USB Device: HASP4 USB 1.33, 0x0529 (Aladdin Knowledge Systems), 0x0001, 0xff100000 / 2
USB Device: HASP HL 3.25, 0x0529 (Aladdin Knowledge Systems), 0x0001, 0xfe200000 / 2
USB Device: Natural® Ergonomic Keyboard 4000, 0x045e (Microsoft Corporation), 0x00db, 0x1a200000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x5a100000 / 2
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8215, 0x5a110000 / 3
USB Device: USB Receiver, 0x046d (Logitech Inc.), 0xc52f, 0x1d100000 / 2
FireWire Device: built-in_hub, Up to 800 Mb/sec
FireWire Device: unknown_device, 0xD016, Up to 200 Mb/sec

Only OS bugs, driver bugs, or hardware problems can cause kernel panics.
Yes, that is normally the case. I brought this up here because while working in PS is the only time this happens. I know it doesn't make sense, but there it is.
Not sure why the crash report stated 10.8.0. It's incorrect on two counts. For one, I'm working in Snow Leopard, 10.6.8. I do have Mountain Lion installed on a separate drive for testing, but that already is at 10.8.2. Regardless, it's not the OS I was even in, so I don't know why it reported 10.8.0 as the kernel.
Anyway, I noticed (after posting this of course) that there was a 13.0.1 update for PS CS6. I applied that and we'll see how it goes from there as the update is noted as fixing a number of crashing problems.

Rt3062 causing kernel panics

Hi all,
I've got an rt3062 chipset wireless card and it's been causing kernel panics ever since the upgrade to linux-3.0.
I was using the driver and firmware supplied by ralink and compiling it as the rt3562sta driver and it used to work great but it doesnt seem to support anything higher than kernel 2.6.39.
I'm not exactly sure which error logs to post, so...
Anybody else having this issue? and maybe find a workaround?
Thanks

I am using the same combination, successfully, with kernel 3.0.7-1. I do not recall having to do anything special to get it to work.
06:00.0 Network controller: Ralink corp. Device 3062
Subsystem: Ralink corp. Device 3062
Flags: bus master, slow devsel, latency 32, IRQ 19
Memory at fbdf0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 3
Kernel driver in use: rt2860
Kernel modules: rt3562sta, rt2800pci
Tim

ITunes causing kernel panics because I'm streaming to multiple Airplay Speakers?

Any idea what is causing kernel panics that seems to have started when I began streaming to multiple Airplay Speakers? iTunes is listed as the culprit in the crash report.

My question: is there a way to select multiple speakers from AppleTV for Airplay?
Unfortunately not.

WD my Cloud 3T causes Kernel Panic in my New iMac?

Dear Friend please I need help.
I got my WD a few days ago, I was able to back up and transfer files to my old iMac, then I got my new iMac
Model Name:iMac
Model Identifier:iMac14,2
Processor Name:Intel Core i7
Processor Speed:3.5 GHz
Number of Processors:1
Total Number of Cores:4
L2 Cache (per Core):256 KB
L3 Cache:8 MB
Memory:32 GB
Boot ROM Version:IM142.0118.B00
SMC Version (system):2.15f2
I was transfering files from WD My Cloud to this new iMac. but suderly started the Kernel Panic, I didn't know what caused the first but then I try to use WD as my Time Machine too but again, a new Kernel Panic, I rebooth my WD My Cloud and tried to do it again, and after 3 hours of backing up another Kernel Panic, this is what I got.
In addition I have a Time Capsule, in which I was able to do a backup before, but I am trying to have another backup because my TM is 2 years old and I don't want to lose information if my TM fail.
Anonymous UUID:       9E0E05EB-600A-D989-25B4-6857F5376BB4
Fri Feb 21 06:14:13 2014
panic(cpu 4 caller 0xffffff80020dc19e): Kernel trap at 0xffffff7f845363ce, type 13=general protection, registers:
CR0: 0x000000008001003b, CR2: 0x000000010c436000, CR3: 0x0000000004c88000, CR4: 0x00000000001606e0
RAX: 0xffffff7f83584fd0, RBX: 0xffffff8390f5fc80, RCX: 0xffffff83a9a73bec, RDX: 0xffffff83a9a73bd8
RSP: 0xffffff83a9a73bd0, RBP: 0xffffff83a9a73c20, RSI: 0xffffff83a9a73bf0, RDI: 0xffffff803fa76b00
R8: 0x0000000000000000, R9: 0xffffff8390f5fc80, R10: 0x0000000000001000, R11: 0x0000000000000000
R12: 0xffffff8390f5fc80, R13: 0xffffff803fa76b00, R14: 0x0000000000000000, R15: 0x0000000000080000
RFL: 0x0000000000010246, RIP: 0xffffff7f845363ce, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x000000010c436000, Error code: 0x0000000000000000, Fault CPU: 0x4
Backtrace (CPU 4), Frame : Return Address
0xffffff8385d3ddf0 : 0xffffff8002022f69
0xffffff8385d3de70 : 0xffffff80020dc19e
0xffffff8385d3e040 : 0xffffff80020f3606
0xffffff8385d3e060 : 0xffffff7f845363ce
0xffffff83a9a73c20 : 0xffffff7f845362fa
0xffffff83a9a73c70 : 0xffffff7f835798e7
0xffffff83a9a73ca0 : 0xffffff7f8357af9d
0xffffff83a9a73ce0 : 0xffffff7f835a2fd6
0xffffff83a9a73d20 : 0xffffff7f8359eeb3
0xffffff83a9a73d60 : 0xffffff7f8359ebea
0xffffff83a9a73dc0 : 0xffffff7f835a665f
0xffffff83a9a73e00 : 0xffffff7f8357b02a
0xffffff83a9a73e30 : 0xffffff7f84536da5
0xffffff83a9a73e70 : 0xffffff7f845360fd
0xffffff83a9a73ec0 : 0xffffff7f8453597b
0xffffff83a9a73f10 : 0xffffff7f84537fc7
0xffffff83a9a73f30 : 0xffffff80024ac522
0xffffff83a9a73f80 : 0xffffff80024ac5f7
0xffffff83a9a73fb0 : 0xffffff80020d6aa7
      Kernel Extensions in backtrace:
         com.apple.iokit.IOAHCIFamily(2.6)[EBAE52B6-A74C-39C9-8845-3F737C85DA9F]@0xfffff f7f83577000->0xffffff7f8358cfff
         com.apple.driver.AppleAHCIPort(2.9.5)[35F30232-E2AA-3305-8B0E-4AF190925824]@0xf fffff7f8452e000->0xffffff7f84547fff
            dependency: com.apple.iokit.IOAHCIFamily(2.6.0)[EBAE52B6-A74C-39C9-8845-3F737C85DA9F]@0xfff fff7f83577000
            dependency: com.apple.iokit.IOPCIFamily(2.8)[447B4896-16FF-3616-95A2-1C516B2A1498]@0xffffff 7f826ba000
         com.apple.iokit.IOAHCIBlockStorage(2.4)[DE2724CF-D751-3AFF-AF39-7DB381393835]@0 xffffff7f8359d000->0xffffff7f835b3fff
            dependency: com.apple.iokit.IOAHCIFamily(2.6.0)[EBAE52B6-A74C-39C9-8845-3F737C85DA9F]@0xfff fff7f83577000
            dependency: com.apple.iokit.IOStorageFamily(1.9)[9B09B065-7F11-3241-B194-B72E5C23548B]@0xff ffff7f825e8000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
13B42
Kernel version:
Darwin Kernel Version 13.0.0: Thu Sep 19 22:22:27 PDT 2013; root:xnu-2422.1.72~6/RELEASE_X86_64
Kernel UUID: 1D9369E3-D0A5-31B6-8D16-BFFBBB390393
Kernel slide:     0x0000000001e00000
Kernel text base: 0xffffff8002000000
System model name: iMac14,2 (Mac-27ADBB7B4CEE8E61)
System uptime in nanoseconds: 30172440187004
last loaded kext at 695661497998: com.apple.filesystems.afpfs 11.0 (addr 0xffffff7f84600000, size 348160)
last unloaded kext at 84962075011: com.apple.driver.AppleFileSystemDriver3.0.1 (addr 0xffffff7f844f8000, size 8192)
loaded kexts:
com.apple.filesystems.afpfs 11.0
com.apple.nke.asp-tcp 8.0.0
com.apple.filesystems.smbfs 2.0.0
com.apple.driver.AppleBluetoothMultitouch 80.14
com.apple.driver.AudioAUUC 1.60
com.apple.driver.AppleHWSensor 1.9.5d0
com.apple.filesystems.autofs 3.0
com.apple.iokit.IOBluetoothSerialManager 4.2.0f6
com.apple.driver.AGPM 100.14.11
com.apple.driver.ApplePlatformEnabler 2.0.9d1
com.apple.driver.X86PlatformShim 1.0.0
com.apple.driver.AppleMikeyHIDDriver 124
com.apple.driver.AppleHDA 2.5.3fc1
com.apple.driver.AppleUpstreamUserClient 3.5.13
com.apple.GeForce 8.1.8
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.driver.AppleBacklight 170.3.5
com.apple.driver.AppleIntelHD5000Graphics 8.1.8
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.2.0f6
com.apple.driver.AppleMikeyDriver 2.5.3fc1
com.apple.driver.AppleSMCLMU 2.0.4d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AppleHWAccess 1
com.apple.driver.AppleMCCSControl 1.1.12
com.apple.driver.AppleLPC 1.7.0
com.apple.driver.AppleIntelFramebufferAzul 8.1.8
com.apple.driver.AppleThunderboltIP 1.0.10
com.apple.iokit.SCSITaskUserClient 3.6.0
com.apple.driver.AppleUSBODD 3.3.5
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 35
com.apple.driver.AppleUSBHub 650.4.4
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.4.0
com.apple.driver.AppleSDXC 1.4.0
com.apple.iokit.AppleBCM5701Ethernet 3.6.9b9
com.apple.driver.AirPort.Brcm4360 800.21.45
com.apple.driver.AppleAHCIPort 2.9.5
com.apple.driver.AppleUSBXHCI 650.4.3
com.apple.driver.AppleACPIButtons 2.0
com.apple.driver.AppleRTC 2.0
com.apple.driver.AppleHPET 1.8
com.apple.driver.AppleSMBIOS 2.0
com.apple.driver.AppleACPIEC 2.0
com.apple.driver.AppleAPIC 1.7
com.apple.nke.applicationfirewall 153
com.apple.security.quarantine 3
com.apple.security.SecureRemotePassword 1.0
com.apple.driver.AppleBluetoothHIDKeyboard 170.15
com.apple.driver.AppleHIDKeyboard 170.15
com.apple.driver.IOBluetoothHIDDriver 4.2.0f6
com.apple.driver.AppleMultitouchDriver 245.13
com.apple.kext.triggers 1.0
com.apple.iokit.IOSerialFamily 10.0.7
com.apple.driver.DspFuncLib 2.5.3fc1
com.apple.vecLib.kext 1.0.0
com.apple.iokit.IOAudioFamily 1.9.4fc11
com.apple.kext.OSvKernDSPLib 1.14
com.apple.nvidia.driver.NVDAGK100Hal 8.1.8
com.apple.nvidia.driver.NVDAResman 8.1.8
com.apple.iokit.IOAcceleratorFamily 98.7.1
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.iokit.IOSurface 91
com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.2.0f6
com.apple.iokit.IOBluetoothFamily 4.2.0f6
com.apple.driver.AppleSMBusController 1.0.11d1
com.apple.driver.AppleHDAController 2.5.3fc1
com.apple.iokit.IOHDAFamily 2.5.3fc1
com.apple.iokit.IONDRVSupport 2.3.6
com.apple.iokit.IOAcceleratorFamily2 98.7.1
com.apple.AppleGraphicsDeviceControl 3.4.12
com.apple.iokit.IOGraphicsFamily 2.3.6
com.apple.driver.X86PlatformPlugin 1.0.0
com.apple.driver.AppleSMC 3.1.6d1
com.apple.driver.IOPlatformPluginFamily 5.5.1d27
com.apple.driver.AppleSMBusPCI 1.0.12d1
com.apple.driver.AppleThunderboltEDMSink 1.2.1
com.apple.driver.AppleUSBMergeNub 650.4.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.6.0
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOUSBMassStorageClass 3.6.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.6.0
com.apple.driver.AppleThunderboltDPOutAdapter 2.5.0
com.apple.driver.AppleThunderboltDPInAdapter 2.5.0
com.apple.driver.AppleThunderboltDPAdapterFamily 2.5.0
com.apple.driver.AppleThunderboltPCIDownAdapter 1.4.0
com.apple.driver.AppleUSBComposite 650.4.0
com.apple.driver.CoreStorage 380
com.apple.iokit.IOUSBUserClient 650.4.4
com.apple.driver.AppleThunderboltNHI 1.9.2
com.apple.iokit.IOThunderboltFamily 2.8.5
com.apple.iokit.IOEthernetAVBController 1.0.3b3
com.apple.iokit.IO80211Family 600.34
com.apple.driver.mDNSOffloadUserClient 1.0.1b4
com.apple.iokit.IONetworkingFamily 3.2
com.apple.iokit.IOAHCIFamily 2.6.0
com.apple.iokit.IOUSBFamily 650.4.4
com.apple.driver.AppleEFINVRAM 2.0
com.apple.driver.AppleEFIRuntime 2.0
com.apple.iokit.IOHIDFamily 2.0.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 278.10
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.AppleKeyStore 2
com.apple.driver.DiskImages 371.1
com.apple.iokit.IOStorageFamily 1.9
com.apple.iokit.IOReportFamily 21
com.apple.driver.AppleFDEKeyStore 28.30
com.apple.driver.AppleACPIPlatform 2.0
com.apple.iokit.IOPCIFamily 2.8
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.pthread 1
com.apple.kec.corecrypto 1.0
Model: iMac14,2, BootROM IM142.0118.B00, 4 processors, Intel Core i7, 3.5 GHz, 32 GB, SMC 2.15f2
Graphics: NVIDIA GeForce GTX 780M, NVIDIA GeForce GTX 780M, PCIe, 4096 MB
Memory Module: BANK 0/DIMM0, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
Memory Module: BANK 1/DIMM0, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
Memory Module: BANK 0/DIMM1, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
Memory Module: BANK 1/DIMM1, 8 GB, DDR3, 1600 MHz, 0x02FE, 0x45424A3831554738454655352D474E4C2D46
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x111), Broadcom BCM43xx 1.0 (6.30.223.154.45)
Bluetooth: Version 4.2.0f6 12982, 3 services, 23 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: APPLE SSD SD0128F, 121.33 GB
Serial ATA Device: APPLE HDD ST3000DM001, 3 TB
USB Device: FaceTime HD Camera (Built-in)
USB Device: BRCM20702 Hub
USB Device: Bluetooth USB Host Controller
USB Device: Apple USB SuperDrive
Thunderbolt Bus: iMac, Apple Inc., 23.10
In addition, after a few hours of not using my WD my Cloud was disconnected from my network.
Can anybody help me please?. I am in the time frame where I can return either the iMac or the WD my Cloud.
Thanks.

A new iMac should not experience a kernel panic. Contact Apple's Support, formerly Apple Express Lane and let them deal with the problem. Do note, that, at least in the US, you can return any Mac the first 14 days w/o any questions asked.

IMac 24" 3.06Ghz (early 2009) 8gb ram upgrade causing kernel panic

When 2 x 4Gb ram modules are installed there is a kernel panic on startup, yet if I mix the old (2Gb) and the new (4Gb) in any slot/module combination to give me a total of 6Gb there is no problem.
It seems the machine is maxing out at 6Gb but Apple states 8Gb as max
New ram modules labeled: 4gb ddr3 pc3-8500 sodimm
System:OSX 7.1

Just found this:
4 GB SODIMMs will not work in most Macs. 4 GB SODIMMs are relatively expensive. The Macs in the chart above listing 6 GB maximums will take one 4 GB plus one 2 GB, but two 4 GB modules crash the machine as soon as the OS tried to access more than 4096 MB of memory. The exceptions are the Early 2009 iMacs (not education model) and the Early 2009 MacBook Pro (except 2.4GHz) which can each take two 4 GB SODIMMs for a maximum of 8GB and, to some extent, the Late 2007 MacBook and later and the Mid 2007 MacBook Pro and later which can take one 4GB SODIMM along with one 2GB SODIMM for a maximum of 6GB.
The above exceprt is from this website.
I wasn't aware that there was an "Education model" however I did buy it through the education store when I was in college, so perhaps this is why I am only able to get the 6 gig to work on my Early 2009. I'd be interested to know if the other people in this thread having this issue also bought their iMacs from the education store.

New Apple keyboard is causing kernel panic on unplugging. Workarounds?

I bought a new (wired) Apple keyboard, the slim one, some time ago to use with my Macbook (first gen) and an external display, using OS X 10.8.10. I have noticed that, after installing Apple's Keyboard Software Update, the Macbook kernel panics whenever I unplug this keyboard from the USB port.
I have had this recurring pattern several times already so I'm quite sure this Keyboard Software Update is the culprit. And it definitely isn't a third-party conflict (I just did an Erase and Install of the OS a couple of days ago). Unfortunately I don't know of a way to "undo" this update. Plus, the Macbook is my current work and home computer so, short of turning it off before unplugging the keyboard (which I'm not used to do) I feel like I'm pretty hosed on this one until Apple releases an update to this keyboard software, which is a pretty annoying issue for me already. Has anyone else been through this? Any alternate solutions?

did you try to repair permission after software and hardware update ?
try that if you haven't done that:
application / utilities / disk utility / repair permission.
Good Luck.

New RAM causing Kernel Panics?

Similar Messages

Maybe you are looking for