New to Apple and Time Capsule Wireless

I am a new apple customer.  I just bought my 1st iMac and I am trying to make the total break from MS.
I have mediacom as my ISP and my present wireless router is a Linksys WRT600n (purchased about 3 years ago).  With this system I have had problems with coverage in my house as well as needing to reboot the device often.
The router is located in a 1st floor bedroom and I get spotty coverage in the living room and even more spotty service in the adjacent kitchen.  The distances away from the router as the crow flies is 24 feet for the living room (involves 4 interior walls) plus 15 more feet (an another wall) to the kitchen.  Since we use our wireless system more in our living room and our bedroom (this is only 12 feet away and 1 interior wall), I have decided to move the wireless router to the living room and place it on top of a entertainment center.  My thinking is that it will provide better coverage to the areas where we use it (hoping to use Apple TV in both living room and bedroom).
This leads me to my question: what has been the experience of the time capsule community in regards to time capsule wireless coverage and reliability?
Also, please note that the iMac will be located in the same bedroom where I will be removing the current router and as such, the wireless backup capabilities of the time capsule will need to traverse the same 24 feet and 4 interior walls.
Any feedback will be most appreciated.
Harvey49

The reliability of the Apple Extreme is very good.. TC much less good. 3years is often a failure point for stuff that runs too hot. Like your WRT600N and the TC with its Green Drive and internal power supply.
On wireless range though I would say pretty ordinary. I have tested all the generations of the TC and most of the Extreme.. including Gen5. In my double storey house with an old G wireless modem router (downstairs extreme end).. right near the TC/AE whichever I am running.. from the other end of the house (upstairs) the old G wireless gives more than adequate signal to get full speed internet.. the TC does not.. And 5ghz goes pretty much to the next room and then disappears but that is as expected.
Use the tests here to find what give good range.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/58-2_4-ghz-dn (you can change the chart to give speed in the worst location ie F http://www.smallnetbuilder.com/lanwan/router-charts/bar/58-2_4-ghz-dn?see=P_F
Airport extreme is there. Well down but there.

Similar Messages

  • HOME HUB AND TIME CAPSULE WIRELESS CONNECTION

    hi,
    i have recently moved house and have BT broadband and Sky TV. The point where the master socket comes into my house is in an upstairs bedroom, well away from my living room where the TV is... So i'm wondering if its possible to have the Home Hub in the bedroom and then connect my apple time capsule wirelessly to it, then run ethernet from the TC to my Sky box for downloading TV etc. I may need to move the BT master socket to the living room, but hoping to find a workaround.
    I have read some of the forums about bridging etc, but im not sure if this will solve the issue.
    Any help would be appreciated!
    Cheers

    Since you, effectively, have two routers in series you will want to reconfigure the downstream router (the TC in this case) as a bridge to allow the upstream router (BT HomeHub) to continue to provide both NAT & DHCP services for all wired & wireless clients.
    To set up the Time Capsule (TC) as a bridge, either connect to the TC's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN port of the TC, and then, using the AirPort Utility, change this setting:
    Internet - Internet Connection tab
    o Connection Sharing: Off (Bridge Mode)
    o Click Update to apply the new settings.

  • OSX Mavericks problems with iMail new mail sound and Time Capsule back-up symbol

    Since I updated to Mavericks, the New Messages Sound in iMail does not work; there is no sound. As well, the time capsule back-up clock-face symbol in the top menu no longer moves when the computer is being backed-up. Any ideas?

    JLS99 wrote:
    I recently purchased a Seagate 750GB Hard Drive, installed the new hard drive in my MBP and completed the steps to restore from my TC.
    Exactly what did you do?   Did you do a full system restore, after starting from your Recovery HD, per #14 in Time Machine - Frequently Asked Questions?
    When it was complete, I re-started my computer and I would see the Apple icon in the middle of my screen for about 10 seconds then the screen would go blank then several lines of messages were visible with the message the computer would not boot.
    This one?
    If so, that's a kernel panic.  All you need to do is install a fresh version of OSX.  See #E8 in Time Machine - Troubleshooting.

  • G4 imac and time capsule wireless connection

    I have a dual band time capsule working wirelessly with 3 macs all intel (24 iMac, mbp 13, mb 13) with no issues. I was trying to connect a 17" flat panel G4 to the same wireless network on the time capsule and it fails to see the network.
    When I type in the network name and password (WPA) it comes back with "encryption method not supported by the wireless network". Although all the others macs are working on this same network using the same encryption, the old iMac refuses to play nice. Is there something else I've overlooked?
    This G4 has been on a various wireless networks over the past 5 years. It is running 10.4.11 and I know it will not support time machine, but still hoping it can share the wireless network.
    Thanks

    James,
    You need to configure the Time Capsule to "join" the wireless network that is being provided by the Netgear router. The Time Capsule will connect using wireless only in this type of configuration.
    Then, the Netgear, Time Capsule and your computer will all be on the same wireless network and you will not have to "switch" networks to access the Internet or back up to the Time Capsule.
    Before we make any changes, we want to make sure that you understand that the Time Capsule will not perform any routing functions when it is configured to "join a wireless network".
    The Ethernet ports on the  Time Capsule are not enabled in this setup, therefore you will not be able to use Ethernet to back up to the Time Capsule. Backups will be over wireless only, which is significantly slower than an Ethernet connection.
    This setup can be tricky because you must know the exact type of wireless security that the Netgear router is using in order to provide the correct settings to the Time Capsule.
    If the Time Capsule does not receive the correct settings during setup, you will receive a message that there has been an error and you must start all over again with a complete factory default reset of the Time Capsule and try again.
    So, before we go any further, we need to ask....what is the exact type of wireless security that your Netgear router is using?

  • Shenanigans with new USB drive and Time Capsule

    It is probably best explained by consulting attached screen grabs (moderator: these are GIFs with filesizes 24K and 32K).
    Drive: STUFF has been attached to TC for a while
    Drive: Stuff 2 is a relatively new addition (old drive whacked into a USB drive container) and attached to TC
    Image e01.gif shows what happens soon after powering up Stuff 2 with error message "The operation cannot be completed because the original item for "Stuff 2" cannot be found."
    Possibly I have mucked up some setting somewhere or maybe used wrong format on Stuff 2?
    Nonetheless after a while (possibly 5 minutes maybe more or less?) I try to access Stuff 2 and BONGO! It mounts fine and dandy (see e02.gif)
    All images have (I hope) been suitably redacted.
    Message was edited by: the deebs redacted again

    There isn't a solution, the Apple TV will only read your iTunes library if iTunes is running and will only play content through iTunes.

  • MacBook Pro and Time Capsule after adding new wireless router

    I have a MacBook Pro and Time Capsule (which functions wirelessly to router and computer). I added a new wireless router (netgear, not my idea) and had to change name of wireless network. Now Time Capsule flashes amber and does not show up in Airport Utility.
    Do I have to set up Time Capsule from scratch? If so, if you can aim me to directions I won't have to waste tech support's time.
    My additional question on a similar vein: I also have a Time Capsule (second time capsule) which is plugged into the wireless router using ethernet cable for use with a windows notebook running windows 7 which backs up wirelessly. Do I have to change anything on this Time Capsule (second Time Capsule) as a result of change in name of network (I've already adjusted computer to connect to network)?

    Hi DD,
    If you don't get answers here, try posting in the Time Capsule forum (http://discussions.apple.com/forum.jspa?forumID=1253) and/or the Time Machine forum (http://discussions.apple.com/forum.jspa?forumID=1342).

  • Hi.. I'm new to mac, I've got a mac book air and time capsule is it possible to save music,video from iTunes Store directly to time capsule leaving my 128GB Mac free? If so  please help..

    Hi.. I'm new to mac, I've got a mac book air and time capsule is it possible to save music,video from iTunes Store directly to time capsule leaving my 128GB Mac free? If so  please help..

    You can move your iTunes library.. Apple have explicit instructions to do it. If the library is moved to the TC and accessed over wireless, the efficiency of the whole system will drop dramatically..
    A file you download goes.. Modem---TC--Laptop--Back to TC--Store on disk. Double looping the wireless slows it dramatically..
    As far as using TC for your iTunes.. you CAN.. but SHOULD YOU?
    Store files on the TC.
    https://discussions.apple.com/message/24380694#24380694
    This is asked several times a day.. obviously people are struggling with their latest SSD being too small.
    The TC is not suitable for network file server.. but many people having no choice press it into service as such.
    It cannot be partitioned. It was and is and ever shall be a backup device for Time Machine.
    Major issues.
    1. No backup.. no way Time Machine can backup a network drive. No place to backup to.. So all your files will be at risk. And you will need to buy a third party like CCC to do backup.
    2. The TC cannot be partitioned and mixing TM backups and data is not great.
    3. The drive is slow to spin up and quick to spin down.. there is no controls.
    4. iPhoto in particular can easily corrupt its entire library with wireless networking causing a disconnection to one photo. Even if you do this;;; do not move your photo library... you have been warned!!
    5. iTunes will constantly lose connection to the library. The disk is too slow to respond.. itunes on the computer will constantly spit out errors. Even in the midst of streaming the TC can spin down the disk due to caching.
    6. Do not use any live files on the TC no matter what else you do.. if you edit files in whatever program the file must be on the local hard disk.
    7. The only suitable location for most libraries is a computer. You can plug in an external hard disk.
    Read pondini for some work arounds.
    Q3 here. http://pondini.org/TM/Time_Capsule.html

  • Wireless connection between D-Link WiFi router and Time capsule stopped working

    We have an ISP provided D-Link wireless router (DIR-615) to which we wirelessly connected our 2Tb Time Capsule for back up and to connect a USB printer to out network. This worked perfectly for 3 1/2 years, until about a month ago, when the time capsule suddenly decided to go "off line". ie we could no longer access it or the printer via our wireless network. We had changed nothing - just one day it stopped working.
    We tried to get it back online with no success. As the 2Tb Time Capsule was almost 7 years old and had had some HDD issues in the passed, we figured it had got old and died and that it was time to replace it; so we bought a new 3Tb Time Capsule, thinking this would get everything back to normal.
    However much as we tried, we were also unable to get the new 3Tb Time Capsule to connect wirelessly to the D-Link wireless router. The Airport Utility did not show the D-Link wireless router or its wireless network, although we were (and are) able to see it in Systems Preferences>Networks from all our multiple devises. This in itself seemed odd. No matter what we tried, the Airport Utility would not find the D-Link wireless router and hence we could not add the 3Tb Time Capsule to the existing wireless network.
    At the end of the day we got fed up with trying to add the 3Tb Time Capsule to the D-Link wireless network, and connected it via a LAN cable to the D-Link router instead. We then set it up as its own network. Worked gerat. Having done that we thought maybe the old 2Tb Time Capsule might not have been the problem after all, so we tried extending our new 3Tb Time Capsule wireless network using the 2Tb Time Capsule wirelessly. This worked perfectly! And we are now almost back to what we wanted.
    So although we have a work around, this means now have 2 separate wireless networks as opposed to the original single wireless network where everything talked to everything else.
    Can anyone shed any light on any of the following:-
    1. Why the original wireless network connection between the D-Link router and the 2Tb Time Capsule just stopped working? Was there some software change from Apple that "decided" D-Link wireless routers were no longer secure; and therefore the TCs could no longer connect to them?
    2. Why it was not possible to extend the existing D-Link wireless network using the the new 3Tb Time Capsule?
    3. Is there is anyway that we can get back to a single wireless network based around the D-Link wireless router as the primary router connecting to the modem, where the 2 Time Capsules connect as "wireless satellite base stations"?

    1. Why the original wireless network connection between the D-Link router and the 2Tb Time Capsule just stopped working? Was there some software change from Apple that "decided" D-Link wireless routers were no longer secure; and therefore the TCs could no longer connect to them?
    A firmware update to the TC came along and you agreed to it without perhaps even noticing.. it then smashed your setup because Apple do not recommend the setup you were using and it is very poor.
    2. Why it was not possible to extend the existing D-Link wireless network using the the new 3Tb Time Capsule?
    Because it is such a poor setup that Apple have taken away your ability to choose it unless you know exactly what you are doing.
    3. Is there is anyway that we can get back to a single wireless network based around the D-Link wireless router as the primary router connecting to the modem, where the 2 Time Capsules connect as "wireless satellite base stations"?
    Yes, this I can help you with.
    I have several ways around the problem.. but the first one is.. why use the DIR-615 at all.. it is not a modem.. it is a very ordinary bottom end, poor single band slow wireless router.
    Why don't you simply remove the DIR-615 from the network completely.. plug whatever it is the ISP supplies you.. an ethernet connection from whatever that modem is you mentioned into the WAN port of the Time Capsule. And use the TC in some router mode.. same as the DIR-615 was setup.. dhcp or pppoe or whatever.. I doubt the TC cannot match it.
    If you have issues please post a few screenshots from the DIR-615 to show how it is setup from the WAN side.. and as long as you are given the username and password or whatever the ISP uses to authenticate then chuck out the DIR-615.
    Tell me if that is a goer.. if not we can work out a few other methods..
    eg. Simply turn off the wireless in the DIR-615. It is poor cf the TC and there is no need for it.. with the TC in bridge only use the TC for wireless as well as wireless extend with your old TC.
    Or setup roaming network where everything uses the same SSID.
    Then you will have one wireless network. And it won't matter what as long as it connects.. although IMHO this is not right as the TC is such a superior router now you are wasting your new TC.

  • How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

    I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer.  So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only.  How to I make the connections?

    Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC.  I've had the Airport Extreme for a year or so.  The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems.  I was expecting the same with the TC.  But the instruction that came with TC say to connect the printer to the TC via USB...which I did.  And the print function worked perfectly but nothing else.  In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else.  I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way.  But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems.  I may try that again...and see if I can get all print functions with just the TC connected
    As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this.  Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
    Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
    After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup.  I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart.  But now I find that the connection only lasts for a short time.  If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
    So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
    So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct?  Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
    Thanks...

  • Can I copy my iTunes files and folders to Time Capsule wirelessly from my PC?

    Can I copy my iTunes files and folders to Time Capsule wirelessly from my PC? I was wondering since my iTunes files and folders are connected to iTunes.

    You can but the TC is the worst possible location. The design is slow to start and quick to stop data connections.. that will cause trouble.
    Moving folders has specific instructions.
    http://support.apple.com/kb/ht1364
    Move it to an external hard disk fine.. but be very sure you will not be happy with the TC as a location.

  • How to extend wireless with airport express and time capsule

    So, I have a time capsule & because of the thick walls in my apartment, I can barely use my ipad and iphone at night in my bedroom! (my macbookPRO stays at 3 bars however!)
    I bought an airport express thinking I could plug it closer to or inside my bedroom to boost the signal - but it doesn't seem to work that way - any tips on how to set this up?
    TWO ADDITIONAL Qs:
    Does connecting directly to my time capsule (which i'm assuming i'd need another ethernet cable) help with the boost? (then negates the other great uses for the airport express it seems)
    Isn't there a way to do the boost with the express wirelessly? I'd really love to get wireless speakers, use airplay AND be able to use my devices just two rooms away ....   HELP!
    thanks so much (when did apple phone support start to be closed on Sundays?)
    cheers.

    Suggest that you check your setup again to make sure that the settings are correct on both the Time Capsule and AirPort Express.
    Open AirPort Utility, select the Time Capsule and click Manual Setup
    Click the Wireless tab below the row of icons
    Make sure that a check mark is entered next to "Allow this network to be extended".( If the box is not checked, the Time Capsule will not extend to the AirPort Express)
    Click Update to save your settings and close AirPort Utility
    Next, open AirPort Utility again, select the AirPort Express and click Manual Setup
    Click the Wireless tab
    Settings should look like this:
    Wireless Mode = Extend a wireless network
    Wireless Network Name = Same name as the Time Capsule network
    Check mark entered next to "Allow wireless clients"
    Wireless Security = Same setting as the Time Capsule
    Wireless Password = Same password as the Time Capsule network
    Confirm Password
    Update to save settings and close AirPort Utility
    Locate the AirPort Express approximately half way between the Time Capsule and area that needs more wireless coverage. You may need to experiment on placement to find the best compomise.
    Post back on your results.

  • I've got an apple 3TB time capsule.  It was working fine until we moved to a new house.  The day the ISP showed up to upgrade my speed it stopped working.  Now will not pick up signal.  What happened what do I do?

    I've got an apple 3TB time capsule.  It was working fine until we moved to a new house.  The day the ISP showed up to upgrade my speed it stopped working.  Now will not pick up signal.  What happened what do I do?

    What signal is it picking up? Are you joining wireless network? If so don't.. it is really poor way to run things.
    Is it connected to a cable modem? Full router or just a modem type?
    Try a reset?
    Plug in via ethernet.. turn off everything.. wait 5min then restart cable modem.. if that doesn't work, give it a longer off cycle.. 15min or overnight.
    We need more info.

  • Best way to extend wireless via airport express and time capsule

    best way to extend wireless via airport express and time capsule
    i live in a two storey house where i use my airport express to create a wireless network in the main floor, and time capsule to extend it in the upper floor, where my room is. i have like 16 mbps in the main floor, and 2-3 mbps in the upper floor after having speediest.
    i used time capsule in the upper floor because i use wireless backup daily and don't want to put internet down while i im doin it and consequently my parent can have internet access in the main floor, am i right? or do i have make just the opposite in order to have a good internet speed?
    secondly, while checking airport express wireless mode on airport utility, there is like 4 different type of radio mode(802 11n bg comp, 802 11n 2.4, 802 11n a comp, 802 11n 5ghz) which i have no idea what they mean
    what do you recommend?
    we have like iphone4, iphone 3g, mbookpro, ipad, ipad 2, samsung tv and a sony vaio laptop in the wireless network
    thank you

    What you have would appear to be working but I can comment how I would redefine your setup.  Note that both Airport Express and Time Capsule can function as wireless base stations so you do have wireless everywhere and at all times — using the Time Capsules for backups doesn’t mean your parents won’t have internet access regardless of the where the base stations are located.
    You appear to have devices to connect to your network that use the 2.4 GHz band with 802.11g such as the iPhone 3G and perhaps the 5 GHz band with 802.11n such as likely the Macbook Pro if it’s a recent model.  The iPhone 4 can use 5 GHz and 802.11n.  Can’t comment on the Sony and Samsung but you can check their specs.
    Now the Time Capsule (if it’s a recent version), can simultaneously supply 2.4 GHz and 5 GHz band signals, but the Airport Express (if it’s recent) can only use one of those bands at one time.  Likely the lowest common denominator for your devices is going to be the 2.4 GHz band since the devices that are capable of using 5 GHZ also support 2.4 GHz.  If you don’t use 5 GHz, you won’t lose much in a two-storey home because likely it’s the 2.4 GHz band is better signal anyway because 5 GHz signals drop off quickly with several walls/floors to penetrate.
    You also didn’t mention if the Airport Express is used to support a printer and/or AirPlay (using iTunes to play on remote speakers via the Airport Express connection) but that might also be a factor in the best location to place the Airport Express.  Although the printer could be switched between the Time Capsule and the Airport Express if needed, only the Airport Express will support your remote speakers.
    Recommend you use the Time Capsule as the Base station.  When using Airport Utility to define the network, after you name your network, etc., select the Wireless tab, check the box “Allow this network to be extended” and set the Radio Mode to "802.11n (802.11b/g compatible)”.
    Using the Airport Utility, click on the Airport Express; after you define the device and network name, select the Wireless tab, define the Wireless Mode as “Extend a Wireless Network” and check the box “Allow wireless clients”. 
    Hope that helps.

  • Screen freezes and popup message says I need to do a shutdown and then restart.  It does it sometimes 2 times a day. Im new to apple and need help.

    My screen freezes and popup message says I need to do a shutdown and then restart.  It does it sometimes 2 times a day. Im new to apple and need help.

    Bad or incompatible RAM is, more often then not, the cause of most Kernel Panics. It could also just need to be reset.
    Here's the most used site for Resolving Kernel Panics. Please do all the steps in order, even if you don't think you need to do a certain step.
    Here is a great MacFixIt article.
     Good Luck!
    DALE

  • TS1550 Do external hard drives mounted on my Mac get backed up by time machine on a time capsule wireless Apple external back up disk? How can I see what folders have been actually stored in the wireless back up disk?

    Do external hard drives mounted on my Mac get backed up by time machine on a time capsule wireless apple external hard disk? How can I see what folders have been actually backed up in the external wireless disk? any help would be appreciated

    They can provided you remove them from the Exclude list. Normally, Time Machine does not automatically backup external drives.

Maybe you are looking for