Nimax.exe Entry point not found

the following file has an error mesage box that pops up when I start my laptop or when I install my DAQcard? Whats causing it and how do I fix it?
Attachments:
error.gif ‏10 KB

I have seen something of this nature with our beta software, but not with our released drivers. Are you, or were you, using any beta version of NI software and/or drivers?
What version of the NI-DQ driver are you using? And the NI-IMAQ driver? And of MAX? You can determine all of these versions in the MAX utility by going to the "Software" folder.
If you cannot even enter MAX then I would definitely recommend uninstalling your NI-DAQ and NI-IMAQ drivers. Our latest versions are NI-DAQ 7.0 and NI-IMAQ 2.6. You can find both by going to http://www.ni.com and clicking on Download Software. These most recent versions should not exhibit the issue you are reporting.
Current Versions
http://digital.ni.com/softlib.nsf/webcategories/9AD71162B755F0E7862
56BBC005F001A?OpenDocument&node=132060_US
Regards,
Justin Britten
Applications Engineer
National Instruments

Similar Messages

NImax.exe entry point not found TDMS_GetDataValueEx in cviTDMS.dll

I have a remote PXI-8108 and I'm trying to create a task in MAX. I have no other tasks as this is my first attempt at creating one. The following sequence is performed on the remote system: left click on the PXI-6713 under "NI-DAQmx Devices" --> create task --> generate signal --> analog output --> voltage --> ao0 --> default name of "MyVoltageOutTask" --> click "Finish"
An error window titled "NIMax.exe - Entry Point Not Found" pops up with the following message: The procedure entry point TDMS_GetDataValuesEx could not be located in the dynamic link library cviTDMS.dll.
The only option is to click "OK", at which time the box continually reappears. the only way to get rid of it is to kill MAX in the windows task manager. When I restart MAX, the remote system data neighborhood has a broken task under it, and clicking on it locks the program up (needs another kill in windows task manager). The only way to get rid of it is to reset the remote system's DAQmx configuration and start over.
I have reinstalled NIDAQ 8.9.0, reset the remote system configuration in MAX, updated/reinstalled all the software on the remote system (so that it matches the host system). not sure what else to try. I figure this should be an elementary step: I've done it plenty of times with simulated devices on a host system. Not sure why the remote system is giving me problems.
Solved!
Go to Solution.

I was able to do this on an 8196 controller no problem with DAQmx 9.0 on the controller and my computer having 8.9.5. Updating to 9.0 or even 8.9.5 should update MAX and hopefully get rid of what you are seeing. You are correct that the host and controller should have the same driver version so make sure you update both of them together. It is quite strange that the error is linking to a LabWindows/CVI dll file. Are you using CVI RT on the controller?
Doug Farrell
Product Manager - Condition Monitoring
National Instruments
National Instruments Condition Monitoring

After LV 5.1 install, get message, "nimax.exe-entry point not found."

Just installed LV 5.1 on customers PC. She already has LV 6.1, and 7.1 installed. Upon reboot, at login screen, the error message below occurs:
"nimax.exe-entry point not found"
"The procedure entry point?GetVirtualChannelObjectOnServer@CNIConfigData@@QAEKPBD0@Z could not be located in the dynamic link library nidaqcfg.dll."
I have tried installing the latest version of MAX. No luck. Any help would be appreciated.
Mark
Attachments:
Ann's.doc ‏30 KB

Hi Marxs,
My first suggestion would be to avoid installing LabVIEW 5.1 if possible. This for a few reasons...
LabVIEW 5.1 has the option to install DAQ with LabVIEW. If you elected to install NI-DAQ with the LV 5.1 install, you will run into driver conflict problems.
If you want to use DAQms with LabVIEW 7.1, you will need to install NI-DAQ 7.1, 7.2 or 7.3. You can also use NI-DAQ 7.3 with LabVIEW 6.1. However, NI-DAQ 7.3 will NOT install support for LabVIEW 5.1. This means that you will not be able to use your DAQ devices in LV 5.1.
If you need DAQ for LV 5.1, you will need to go back to NI-DAQ 6.9.3. This version will work with 5.1 and 6.1, but you will loose functionality in LabVIEW 7.1.
My suggestions would be as follows:
-- uninstall LabVIEW 5.1 and all versions of DAQ that are on the machine
-- re-install LabVIEW 5.1 but choose the "custom" and elect NOT to install DAQ
-- Install NI-DAQ 7.3 and have support for 7.1 and 6.1 (no support for 5.1 is available)
Basically, when you try to mix these very old versions of LabVIEW and DAQ with the newer stuff you will run into driver conflicts that can be unpredictable.

NIMax.exe - Entry Point Not Found - attempt to create task in MAX

I have two different cards that use NI-DAQmx: PXI-4461 and PXI-6259. They are installed in a PXI-1031 chassis with a PXI-8105 controller. Both devices pass their self-test in MAX. When I try to create a new task for either, I get first the expected selection dialog:
After I select "Analog Voltage" (or any other item), I get the following error:
Last week, I upgraded my HSDIO driver for a PXI-6562, which led me to upgrade NI-DAQmx to 9.2.3, and subsequently repair both installations in Windows to get them working (see this forum thread).
Task creation used to work. The system still recognizes the one task that I created weeks ago for the PXI-4461.
Here is a screenshot of my current software versions:
Does anyone know how to fix this?
Solved!
Go to Solution.

I solved this problem by downloading and installing NI-DAQmx 9.3.0. This, in turn, caused the problem from the post that I linked above, which I fixed by choosing "repair" in the Windows control panel for 1. the HSDIO driver, and then 2. the NI-DAQmx driver. The order matters. Now it seems to be working.

Error message when clicking on links from thunderbird: Firefox.exe – Entry Point Not found

When I click on any link in a Thunderbird email message I get the error message:
Firefox.exe – Entry Point Not found
The procedure entry point ?DllBlocklist_Initialize@@YAXXZ could not be located in the dynamic link library T:\PQligP sFuvy (X86)\pJPpSox HneiCFv\GwCMqTQ.Oqt.
I tried uninstalling Firefox 27 completely and reinstalling it, and the error is still there. When I uninstall V27 and install the older V26 the error disappears. Id there an issue with V27 trying to work with links from Thunderbird?
I am on a laptop running Windows 8.1 with all current downloads.

Thanks for the reply - as best as I can tell it seems to be some kind of incompatibility between Thunderbird V24.3.0 and Firefox V27. If I install Firefox V26 then everything works as it should. I haven't tried installing a previous version of Thunderbird to see if that makes a difference.

Why is my itunes not installing properly? I installed it and it was fine, then it started to show Errors. iTunes exe - Entry Point not Found. And the Error 7 (Windows error 127).Itsays to reinstall iTunes. I did that and same error. new pc, same on old

Why is my itunes not installing properly?
I installed itunes day before yesterday, I spent hours last night linking all my music photograph and movie files, its a new windows 8 laptop.
I plugged in my 64GB ipad 3 rebooted it and reloaded all the information I wanted on it, took hours... finally completed this this morning. After this I restarted the laptop to configure my icloud link for the laptop (which I installed last night while I was loading files, I chose to restart later)
on completion I turned my laptop off for a few hours, when I turned it back on I went to itunes to connect my iphone to do the same and I got this message:
iTunes exe - Entry Point Not Found
The procedure entry point
AVCFPlayerAppliesMediaSelectionCriteriaAutomaticallyKey could not
be located in dynamiclink library F:\Programmes\iTunes.dll
                                                                                           OK
then after pressing 'OK' the following message:
iTunes
iTunes was not installed correctly. Please reinstall iTunes
Error 7 (Windows error 127)
I went back to apple website to reinstall iTunes, first reinstalled it same again, then unsinstalled it and the reinstalled it, same again.
The same thing happened with my old lap top and I replaced it with this new one at the start of the week.
Has anyone any idea what is going on and how to rectify this problem, I am now going on 3 weeks without iTunes.
Regards,
Damian36

I started up and plugged in my iPad and then the following message came up:
       iTunes
❗️This iPad cannot be used because the required software is not
    Installed. Run the iTunes installer to remove iTunes, then install
    the 64-bit version of iTunes.
                                                                                         OK
I then proceeded to the "iTunes64Setup" expanded folder to load "AppleMobileDeviceSupport64"
Started the install and then received this message:
      Apple Mobile Device Support
❗️Service 'AppleMobile Device' (Apple Mobile Device)
    failed to start. Verify that you have sufficient
    Privileges to start system services.
   Abort.               Retry.                Ignore
I tried all tree options, last being ignore.
I continued to download the other 2 you suggested with out any drama.
I did a system restart and then opened iTunes.
Connected my iPad
Then message appears:
      iTunes .exe - System Error
❌ The program can't start because CoreAdioToolbox.dll is missing from
      Your computer. Try reinstalling the program to fix the problem.
                                                                                       OK
Press OK and then the next message:
       iTunes
❌ iTunes was not installed correctly. Please reinstall iTunes.
      Error 7 (Windows error 126)
                                                                                       OK
Any suggestions?

Crystal Reports 2008-Vista-ERROR-crw32.exe Entry Point Not Found in dll

Hi Experts,
I just installed the Crystal Reports 2008 (with SP0) on my Vista (Home) machine. When I try to start the CR 2008, I am getting the below error message:
Error Title: crw32.exe - Entry Point Not Found
Error Message: The procedure entry point ?PrintLegend@CMapXLegend@CSLib300@@QAEXJJJJJ@Z could not be located in the dynamic link library cslibu-3-0.dll
Here are the things I tried to resolve the above problem:
1) Uninstall and Reinstall the CR 2008. - No change.
2) I configured the DEP to accept Crystal Reports (Performance - Advanced - DEP allow).
None of these seem fix the problem.
Can you please help me kick start the Crystal Reports 2008?
Thanks,
Arun

Please try with this:
Run a command prompt as administrator. From the start menu, select "All Programs", then "Accessories" and right-click on the "Command Prompt" shortcut and choose "Run As Administrator". From here you can use the following command to disable Data Execution Prevention (DEP) with the following command:
bcdedit.exe /set nx AlwaysOff
Keeping your command prompt open, run your setup or other process being stopped by DEP. Then, to turn it back on again, do the same and run the following:
bcdedit.exe /set nx AlwaysOn
Regards,
Shweta

When I connect my new ipod nano to my laptop (using windows)I get an error message saying "itunes.exe - entry point not found" I cannot access my itunes , or download a new version. Any ideas what to do or what is causing this?

I have been given a new ipod nano to replace my much loved but old ipod. When I plug it into my laptop to sync it I get an error message stating "itunes.exe - entry point not found. The procedure entry point AVCFAAssetCreateWithByteStreanAndOptions could not be located in the dynamic link library
AVFoundationCF.dll" I cannot acces my itunes or download a new versiona as this keeps flashing up. Any ideas? Please help, my life is meaningless without my music!!

Also I now can`t access any of my itunes library and am concerned that if I remove it from my computer I will lose everything as I have no option of accessing and therefore backing anything up. Any ideas?

I see a AppleSyncNotifier.exe - Entry Point Not Found error when my PC starts.

when booting up my computer, even before I try to bring up itunes, I get the following error message:
AppleSyncNotifier.exe - Entry Point Not Found
the procedure entry point ___cfconstantstringclassreference could not be located in the dynamic link library core foundation.dll
But once I click off the message, everything seems to work fine.
how can I correct this problem?
2 IPod 5.1.1
1 IPad 2 wifi
Windows Vista 32

Try here > http://www.pchelpforum.com/xf/threads/applesyncnotifier-exe-entry-point-not-foun d.124298/

OutlookSyncClient.exe - Entry Point Not Found

I'm at wit's end with this. I've spent most of last night, and this morning trying to track this down. It all started with the iTunes 7.7 update, but it didn't happen until I started syncing Outlook with MobileMe. I get two error messages, about every 15-20 minutes. MobileMe is set to sync "automatically." At one point, I was getting and error message stating that MobileMe couldn't sync and to check my settings. The settings were right, and apparently in my troubleshooting steps I've made that error go away.
OutlookSyncClient.exe - Entry Point Not Found
The procedure entry point MAPIInitialize could not be located in dynamic link library MAPI32.DLL
It has nothing but an OK box, I hit that, and directly after I get another one with the exact same message.
The best part is, the syncing is working fine with MobileMe. These error messages are driving me nuts.
I uninstalled my Nokia's syncing software BEFORE I attempted to even setup with MobileMe (the Nokia was my pre-iPhone-phone). I've uninstalled/reinstalled iTunes. I've uninstalled/reinstalled Office 2003 and its service pack. I've completed all critical updates to Office. I'm running XP Pro SP3 with all critical updates completed. I've also manually deleted the MAPI32.DLL file and ran FIXMAPI to replace it with a good copy.
UPDATE: When I previously stated that I got rid of the MobileMe Sync error message, I apparently have not. It pops up randomly and says:
The sync failed because MobileMe is not property configured on your computer.
Make sure your settings are correct under the Sync tab in the MobileMe preferences on this computer.
They are correct. If I hit the Sync Now button, everything goes smoothly.
Any ideas before I just set fire to this thing?
Thanks in advance for any assistance.
Message was edited by: supradave

UPDATE - (Made a second post so it'd be clearer)
I uninstalled Office 2003, then iTunes, then all of the associated software (Mobile Device Support, Apple Update, Quicktime, EVERYTHING)
Reinstalled Office 2003, then Office 2003's Service Pack 3, then all Microsoft Updates for Office 2003. Then I configured a blank Outlook profile, no data other than the IMAP info for my .Mac/Me account. Then I downloaded (didn't used my existing copy) of iTunes 7.7 and reinstalled. Sync'd phone. Changed MobileMe settings. Told it to sync contacts and calendar with Outlook. It warned me because it was the first sync. Told it to take ALL of the MobileMe data and replace the data on the computer (which was blank.) NOTHING showed up in Outlook. When I tell it to sync Contacts with the Windows Address Book, it works fine.
In Conclusion, it still won't sync with Outlook, when it's set to Sync with Outlook I still get the annoying MAPI errors. So I switched to to Sync the Contacts with the Windows Address Book, and I'm backing up my WAB file now with my nightly backups.
I suppose we'll see if it gets fixed when I format/reinstall on Vista Ultimate in the next month or two. If anyone has any suggestions, I'm open and willing to try them.
On a completely unproductive note: Despite my love for Exchange, I hate MAPI.

Safari.exe - Entry Point Not Found

I just recently installed Skype because Yahoo! instant messanger has been giving me problems. Safari was running just fine last night, and when I turned my computer on this morning, I received this message:
Safari.exe - Entry Point Not found
The procedure entry point sqlite3_wal_checkpoint could not be located in the dynamic link library SQLite3.dll.
When I click "OK," I receive this message:
Safari can't open.
Your copy of Safari is missing important software resources. Please reinstall Safari.
I have reinstalled Safari several times, but I still receive the same messages. I had found a thread from 2010, and attempted to try what was suggested on there, and it suggested to uninstall the AAS as well as safari, and now I cannot open iTunes. This is very bothersome because I use Safari as my primary browser.
Some aditional information, I am using a PCLaptop and running Windows 7. I have a lot of things saved in my bookmarks on Safari, and really would not like to use them. Also, I am a bit computer illiterate and need everything spelled out for me.
Help please!

Safari for Windows is long dead. I suggest you remove it and let it rest in peace.

Photoshop.exe - Entry Point Not Found (MSVCP80.dll)?

Hey guys, new to the board here and pretty much at the end of my rope.
Starting maybe 2 days ago I began getting quite a strange message when I tried to open Photoshop CS3.
I'd send a jpeg of the window but with photoshop down i'll settle for just typing this crap out:
Photoshop.exe - Entry Point Not Found
The Procedure entry point ?replace@?$basic_string@DU$char_traits@D@std@@V?$a llocator@D@2@@std@@qaeaav12@IIPBD@Z could not be located in the dynamic link library MSVCP80.dll
Now, that's a mouthful! Fortunately i'm at least computer literate enough to dig around on google.
After doing that, I came up with nothing. I found a replacement for the DLL that it's having trouble with, but that did nothing.
I then tried out a program called Registrybooster, which found quite a few problems with my registry but failed to correct whatever is causing this problem.
So I tried to backtrack a little bit and see if anything I had done since the last time the program worked (wednesday the prior week) had broken it. I had shut off some startup programs so i figured maybe that had something to do with it. Unfortunately undoing those changes had absolutely no effect at all.
I then tried out doing a repair install, which did nothing. After this, I did an uninstall and reinstall and... nothing.
Some extra info: I run windows xp home edition on this PC and have it updated to SP3.
I've had photoshop on it for about a year with no problems.
Hopefully someone can help me here. Almost every thread I located with similar problems via google either went unanswered or the answers given didn't actually help me out.
Someone save me!

Hi Chris, thanks for chiming in on my problem.
I'm doubtful of it being TWAIN/WIA caused, but will look into it. I have a wacom tablet and a canon scanner so who knows. What would you suggest I do to see if those two are causing anything in particular? (Not sure why they would as I haven't made any changes to the programs or hardware involved recently.)

ApplySyncNotifier.exe- Entry Point Not Found?

Ever since I loaded the newest "update" on iTunes, when I turn on my computer I get the following error message:
ApplySyncNotifier.exe- Entry Point Not Found
The procedure entry point sqlite3_wal_checkpoint could not be located in the dynamic link library SQLite3.dll
I searched the forums and found some replies but none of them work for me--could it be because those answers were for Windows Vista? I have Windows 7, 64 Bit. ny ideas? I'm tired of this error message popping up constantly and nothing I hve tried has fixed it. I really don't understand why people love Apple products so much, it seems like I constntly have issues with my iPod and iTunes....

This executable belongs to Citrix: http://www.file.net/process/wfica32.exe.html
Please ask them in Citrix forums or contact their support for assistance.
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

What is this dialogue message - AppleSync Notifier.exe-Entry Point not found?

I need help to understand this dialogue box that appeared each time I powered on my computer -
"AppleSync Notifier.exe-Entry Point not found" The proedure entry point sqlite3.wal_checkpoint cold ot be located in the dynamic link library SGLite3.dll.
This message appeared after I downloaded the latest version of the iTune into my laptop Windows 7 Home edition.
Did I download the version wrongly?
Will this affect the sync process of my iPhone?
Please help
Thank you

Also I now can`t access any of my itunes library and am concerned that if I remove it from my computer I will lose everything as I have no option of accessing and therefore backing anything up. Any ideas?

Itunes 11 will not open itunes.exe entry point not found

Every time I try to launch itunes this message box shows up:
iTunes.exe - Entry Point Not Found
The procedure entry point kCVKmageBufferChromaSubsampling_420 could not be located in the dynamic link library CoreVideo.dll
When I click ok another message box shows up:
iTunes
iTunes was not installed correctly. Please reinstall iTunes.
Error 7 (Windows error 127)
I redownloaded itunes directly from apple.com. I clicked on the repair option. It completed. The error is still happening. I have been using itunes for over 10 years with no problems until now.
PC info:
Windows 7 32bit service pack 1 x86
3GB ram
AMD Athlon 64 processor 3500+ 2.20 GHz
NVIDIA GeForce 210 video card 2.2 GB
Also I used the Firefox browser to download itunes.

update:
I just restarted my computer. Now it seems to be working fine. Next time I update itunes I'll just restart my computer twice.

Nimax.exe Entry point not found

Similar Messages

Maybe you are looking for