No Bootable Device error after fresh install

I recently erased the original 80gb hard drive from my MacMini by removing the hard drive from the mini and putting it in a HD enclosure. Afterwards, I erased it using the Disk Utilities on my Macbook Pro before installing Snow Leopard. The installation went error free and was able to load the OS from my MacMini HD that was in the enclosure. However, when I put the hard drive back into my MacMini, I get the "No Bootable Device - Insert boot disk or press any key" message. I repeated the erase and installation 3x but still get the same message.

witch mac mini do you have? is it a G4 or intel?
Is there a reason you pulled the drive instead of just booting to the install disk?
Is the install disk the one that was included with your MacBook Pro? or is it a commercial disk?
Do you know if you partitioned the hard driving using GUID or some thing else?

Similar Messages

Satellite A305 problem: "No bootable device" error after dropping unit

I'm hoping someone can help me out here. Last night, I went to set my A305 laptop down on the coffee table. During the motion, my dog, which I was stepping over, jumped up and took off which almost knocked me over. When this happened, I lost my grip on the computer and dropped it onto the coffee table at a height of about 2-3 feet. It was in standby mode so I pressed the button to wake it back up to see if I damaged it. The Internet Explorer session I was previously in pulled up, but nothing would happen when I clicked on any browser buttons or links. I shut down the computer and upon restarting, I got the black screen with "TOSHIBA" in red, as usual, and then I got a black screen with this error message: For Realtek RTL8101E/8102E PCI-E Ethernet Controller v1.07 (080320)PXE-E61: Media Test Failure, check cablePXE-M0F: Exiting PXE ROMNo bootable device -- insert boot disk and press any key I couldn't get it to do anything else at all, even after several shut down attempts. Does anyone know what could be causing this to happen? Is it a hard drive malfunction as a result from the drop? The unit had worked perfectly for a little over a year up until this point. Any help would be greatly appreciated.

Possible, yes. Can you do it at home, no. Due to the clearances involved you need to do this in a special clean room as the slightest piece of dust or debri that is normally floating around in the air would ruin the platters that the data is stored on. If the drive won't work you'll need to send it to a professional data recovery service to have them do it and the cost of something like that starts at about a grand and goes up depending on the specifics. But before we go there you need to determine if the problem is for sure the hard drive. Enter the bios and check to see if it is even being recognized or not. Also, take the hard drive out and boot to a self booting CD/DVD like a Linux Live CD to verify that the rest of the system is working properly. If it isn't, then the problem might not be the hard drive itself (although the chances of that are about the same as winning the lottery). If the laptop had been off there is a good chance that it would have survived and still worked. But anytime a rotating hard drive sustains any sort of impact shock the chances of it sustaining damage are about 98%.

Socket/JVM_Bind Errors after fresh install

I am trying to install Weblogic on a Development box on a fresh, additional Oracle Home. When running a clean Weblogic install and configuring a standard starter domain, I am unable to hit the console from my browser and I have no idea why. I configured the domain to use 7002 instead of the standard 7001 port so it would not conflict with the original Oracle Home's Weblogic install (although we will never have them both running simaltaneously - I just did it to be safe). I've tried using http://<IP ADDRESS>:7002/console, http://localhost:7002/console, and http://<DOMAIN NAME>:7002/console with no luck. It does not hang at all and just brings me to a "cannot display the page" message. I'm seeing JVM_Bind errors (server address already in use), although I know it is not in use. Here is the output I get when I start up Weblogic:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:\Users\V-Tsmith>G:\Oracle\Middleware\user_projects\domains\base_domain\bin
'G:\Oracle\Middleware\user_projects\domains\base_domain\bin' is not recognized a
s an internal or external command,
operable program or batch file.
C:\Users\V-Tsmith>G:\Oracle\Middleware\user_projects\domains\base_domain\bin\sta
rtWebLogic.cmd
JAVA Memory arguments: -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=
48m -XX:MaxPermSize=128m
WLS Start Mode=Development
CLASSPATH=G:\Oracle\Middleware\patch_wls1036\profiles\default\sys_manifest_class
path\weblogic_patch.jar;G:\Oracle\Middleware\patch_ocp371\profiles\default\sys_m
anifest_classpath\weblogic_patch.jar;G:\Oracle\Middleware\jdk160_29\lib\tools.ja
r;G:\Oracle\Middleware\wlserver_10.3\server\lib\weblogic_sp.jar;G:\Oracle\Middle
ware\wlserver_10.3\server\lib\weblogic.jar;G:\Oracle\Middleware\modules\features
\weblogic.server.modules_10.3.6.0.jar;G:\Oracle\Middleware\wlserver_10.3\server\
lib\webservices.jar;G:\Oracle\Middleware\modules\org.apache.ant_1.7.1/lib/ant-al
l.jar;G:\Oracle\Middleware\modules\net.sf.antcontrib_1.1.0.0_1-0b2/lib/ant-contr
ib.jar;G:\Oracle\Middleware\wlserver_10.3\common\derby\lib\derbyclient.jar;G:\Or
acle\Middleware\wlserver_10.3\server\lib\xqrl.jar
PATH=G:\Oracle\Middleware\patch_wls1036\profiles\default\native;G:\Oracle\Middle
ware\patch_ocp371\profiles\default\native;G:\Oracle\Middleware\wlserver_10.3\ser
ver\native\win\32;G:\Oracle\Middleware\wlserver_10.3\server\bin;G:\Oracle\Middle
ware\modules\org.apache.ant_1.7.1\bin;G:\Oracle\Middleware\jdk160_29\jre\bin;G:\
Oracle\Middleware\jdk160_29\bin;C:\Program Files\CA\SC\CAWIN\;C:\xPression\Drive
rs;E:\Program Files\Legato\nsr\bin;C:\Program Files\HP\NCU;C:\Windows\system32;C
:\Windows;C:\Windows\System32\Wbem;C:\PROGRA~1\CA\SC\CAM\bin;C:\Program Files\CA
\SC\Csam\SockAdapter\bin;C:\Program Files\CA\DSM\bin;C:\Program Files\CA\SC\CBB\
;G:\Oracle\Middleware\wlserver_10.3\server\native\win\32\oci920_8
* To start WebLogic Server, use a username and *
* password assigned to an admin-level user. For *
* server administration, use the WebLogic Server *
* console at http:\\hostname:port\console *
starting weblogic with Java version:
java version "1.6.0_29"
Java(TM) SE Runtime Environment (build 1.6.0_29-b11)
Java HotSpot(TM) Client VM (build 20.4-b02, mixed mode)
Starting WLS with line:
G:\Oracle\Middleware\jdk160_29\bin\java -client -Xms256m -Xmx512m -XX:CompileT
hreshold=8000 -XX:PermSize=48m -XX:MaxPermSize=128m -Dweblogic.Name=AdminServer
-Djava.security.policy=G:\Oracle\Middleware\wlserver_10.3\server\lib\weblogic.p
olicy -Xverify:none -da -Dplatform.home=G:\Oracle\Middleware\wlserver_10.3 -Dw
ls.home=G:\Oracle\Middleware\wlserver_10.3\server -Dweblogic.home=G:\Oracle\Midd
leware\wlserver_10.3\server -Dweblogic.management.discover=true -Dwlw.iterati
veDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=G:\Oracl
e\Middleware\patch_wls1036\profiles\default\sysext_manifest_classpath;G:\Oracle\
Middleware\patch_ocp371\profiles\default\sysext_manifest_classpath weblogic.Ser
ver
<Oct 17, 2012 11:07:34 AM EDT> <Info> <Security> <BEA-090905> <Disabling CryptoJ
JCE Provider self-integrity check for better startup performance. To enable thi
s check, specify -Dweblogic.security.allowCryptoJDefaultJCEVerification=true>
<Oct 17, 2012 11:07:34 AM EDT> <Info> <Security> <BEA-090906> <Changing the defa
ult Random Number Generator in RSA CryptoJ from ECDRBG to FIPS186PRNG. To disabl
e this change, specify -Dweblogic.security.allowCryptoJDefaultPRNG=true>
<Oct 17, 2012 11:07:35 AM EDT> <Info> <WebLogicServer> <BEA-000377> <Starting We
bLogic Server with Java HotSpot(TM) Client VM Version 20.4-b02 from Sun Microsys
tems Inc.>
<Oct 17, 2012 11:07:35 AM EDT> <Info> <Management> <BEA-141107> <Version: WebLog
ic Server 10.3.6.0 Tue Nov 15 08:52:36 PST 2011 1441050 >
<Oct 17, 2012 11:07:36 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server st
ate changed to STARTING>
<Oct 17, 2012 11:07:36 AM EDT> <Info> <WorkManager> <BEA-002900> <Initializing s
elf-tuning thread pool>
<Oct 17, 2012 11:07:36 AM EDT> <Notice> <LoggingService> <BEA-320400> <The log f
ile G:\Oracle\Middleware\user_projects\domains\base_domain\servers\AdminServer\l
ogs\AdminServer.log will be rotated. Reopen the log file if tailing has stopped.
This can happen on some platforms like Windows.>
<Oct 17, 2012 11:07:36 AM EDT> <Notice> <LoggingService> <BEA-320401> <The log f
ile has been rotated to G:\Oracle\Middleware\user_projects\domains\base_domain\s
ervers\AdminServer\logs\AdminServer.log00002. Log messages will continue to be l
ogged in G:\Oracle\Middleware\user_projects\domains\base_domain\servers\AdminSer
ver\logs\AdminServer.log.>
<Oct 17, 2012 11:07:36 AM EDT> <Notice> <Log Management> <BEA-170019> <The serve
r log file G:\Oracle\Middleware\user_projects\domains\base_domain\servers\AdminS
erver\logs\AdminServer.log is opened. All server side log events will be written
to this file.>
<Oct 17, 2012 11:07:37 AM EDT> <Notice> <Security> <BEA-090082> <Security initia
lizing using security realm myrealm.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server st
ate changed to STANDBY>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server st
ate changed to STARTING>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <LoggingService> <BEA-320400> <The log f
ile G:\Oracle\Middleware\user_projects\domains\base_domain\servers\AdminServer\l
ogs\base_domain.log will be rotated. Reopen the log file if tailing has stopped.
This can happen on some platforms like Windows.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <LoggingService> <BEA-320401> <The log f
ile has been rotated to G:\Oracle\Middleware\user_projects\domains\base_domain\s
ervers\AdminServer\logs\base_domain.log00002. Log messages will continue to be l
ogged in G:\Oracle\Middleware\user_projects\domains\base_domain\servers\AdminSer
ver\logs\base_domain.log.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Log Management> <BEA-170027> <The Serve
r has established connection with the Domain level Diagnostic Service successful
ly.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server st
ate changed to ADMIN>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server st
ate changed to RESUMING>
<Oct 17, 2012 11:07:38 AM EDT> <Error> <Server> <BEA-002606> <Unable to create a
server socket for listening on channel "Default". The address 10.32.125.34 migh
t be incorrect or another process is using port 7002: java.net.BindException: Ad
dress already in use: JVM_Bind.>
<Oct 17, 2012 11:07:38 AM EDT> <Error> <Server> <BEA-002606> <Unable to create a
server socket for listening on channel "Default[8]". The address 127.0.0.1 migh
t be incorrect or another process is using port 7002: java.net.BindException: Ad
dress already in use: JVM_Bind.>
<Oct 17, 2012 11:07:38 AM EDT> <Error> <Server> <BEA-002606> <Unable to create a
server socket for listening on channel "Default[9]". The address 0:0:0:0:0:0:0:
1 might be incorrect or another process is using port 7002: java.net.BindExcepti
on: Address already in use: JVM_Bind.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
1]" is now listening on fe80:0:0:0:49ad:74ba:d80b:c53b:7002 for protocols iiop,
t3, ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Warning> <Server> <BEA-002611> <Hostname "NYOSEH
STSTPR01.private.private.com", maps to multiple IP addresses: 10.32.125.34,
fe80:0:0:0:51cf:60de:d2c5:c4dc%14>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
2]" is now listening on fe80:0:0:0:8d6:9a3f:dfac:6dcf:7002 for protocols iiop, t
3, ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
7]" is now listening on fe80:0:0:0:754d:df3f:468f:a1b6:7002 for protocols iiop,
t3, ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
6]" is now listening on fe80:0:0:0:c914:19c3:967c:20ba:7002 for protocols iiop,
t3, ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
3]" is now listening on fe80:0:0:0:9c14:2ea0:9c82:1f28:7002 for protocols iiop,
t3, ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
5]" is now listening on fe80:0:0:0:51cf:60de:d2c5:c4dc:7002 for protocols iiop,
t3, ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[
4]" is now listening on fe80:0:0:0:0:5efe:a20:7d22:7002 for protocols iiop, t3,
ldap, snmp, http.>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000331> <Started W
ebLogic Admin Server "AdminServer" for domain "base_domain" running in Developme
nt Mode>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server st
ate changed to RUNNING>
<Oct 17, 2012 11:07:38 AM EDT> <Notice> <WebLogicServer> <BEA-000360> <Server st
arted in RUNNING mode>
When I first started it up after the install, I was having Socket Errors spit out after the "RUNNING" message (which for some reason isn't happening now):
<Oct 17, 2012 11:03:36 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 1,
failing for 0 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:03:37 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 2,
failing for 1 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:03:39 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 3,
failing for 3 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:03:42 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 4,
failing for 6 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:03:46 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 5,
failing for 10 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:03:51 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 6,
failing for 15 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:03:57 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 7,
failing for 21 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:04:04 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 8,
failing for 28 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:04:12 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 9,
failing for 36 seconds, java.net.SocketException: socket closed>
<Oct 17, 2012 11:04:21 AM EDT> <Critical> <Server> <BEA-002616> <Failed to liste
n on channel "Default[4]" on fe80:0:0:0:0:5efe:a20:7d22:7002, failure count: 10,
failing for 45 seconds, java.net.SocketException: socket closed>

Hi,
This clearly indicates that 7002 port is already used and it cannot bind with 7002 for now.
Try to change with 7002 to other port number like 7003 or any thing will solve your problem.
Regards,
Kal

Console Messages:Color profile errors after fresh install of Snow Leopard

This is a dump of the Console Messages for my Macbook Pro immediately after a fresh install.
Are all the Color profile errormessages normal?
24/12/2010 16:06:02 com.apple.launchd[1] * launchd[1] has started up. *
24/12/2010 16:06:17 com.apple.launchd[1] (com.apple.bsd.dirhelper) Throttling respawn: Will start in 6 seconds
24/12/2010 16:06:18 com.apple.launchd[1] (com.apple.smb.sharepoints[24]) Exited with exit code: 71
24/12/2010 16:06:20 com.apple.launchd[1] (com.apple.bsd.dirhelper) Throttling respawn: Will start in 3 seconds
24/12/2010 16:06:35 com.apple.service_helper[90] launchctl: Error unloading: com.apple.backupd-auto
24/12/2010 16:06:35 com.apple.service_helper[90] launchctl: Error unloading: com.apple.backupd-wake
24/12/2010 16:06:35 com.apple.service_helper[90] launchctl: Error unloading: com.apple.backupd-attach
24/12/2010 16:06:37 com.apple.fontd[82] FODBCheck: foRec->annexNumber != kInvalidAnnexNumber (0)
24/12/2010 16:06:38 com.apple.fontd[82] FODBCheck: foRec->annexNumber != kInvalidAnnexNumber (0)
24/12/2010 16:08:52 com.apple.coreservicesd[49] ThrottleProcessIO: throttling disk i/o
24/12/2010 16:18:07 com.apple.service_helper[150] org.ntp.ntpd: Already loaded
24/12/2010 16:21:43 com.apple.coreservicesd[49] ThrottleProcessIO: throttling disk i/o
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorIllegalArgument: CGSGetDisplayBounds (display 0)
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Warning>: CGSLookupServerPort: _CGSSessionDeathWatchPort(gSessionPort) returns 268435459
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: kCGErrorFailure: CGSColorProfileCreateWithColorProfileID: Cannot initialize color profile client
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Error>: (ipc/send) invalid destination port: CGSGetNextEventRecord (Inline) connection 0x7b07, 16384 bytes
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Warning>: CGSShutdownServerConnections: Detaching application from window server
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Warning>: CGSDisplayServerShutdown: Detaching display subsystem from window server
24/12/2010 16:24:34 [0x0-0x8008].com.apple.IncompatibleAppDisplay[203] Fri Dec 24 16:24:34 Jeremy-Gordon-Flowerss-MacBook-Pro.local IncompatibleAppDisplay[203] <Warning>: 3891612: (connectAndCheck) Untrusted apps are not allowed to connect to or launch Window Server before login.
24/12/2010 16:24:36 com.apple.launchd.peruser.501[215] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
24/12/2010 16:24:36 migCacheCleanup[221] Flushing Cache Locations...
24/12/2010 16:24:36 com.apple.loginwindow[205] 2010-12-24 16:24:36.819 migCacheCleanup[221:903] Flushing Cache Locations...
24/12/2010 16:24:38 SoftwareUpdateCheck[229] Checking for updates
24/12/2010 16:24:40 com.apple.fontd[228] FODBCheck: foRec->annexNumber != kInvalidAnnexNumber (0)
24/12/2010 16:24:42 com.apple.launchd.peruser.501[215] (com.apple.Kerberos.renew.plist[247]) Exited with exit code: 1
24/12/2010 16:24:43 com.apple.fontd[228] FODBCheck: foRec->annexNumber != kInvalidAnnexNumber (0)
24/12/2010 16:26:53 SoftwareUpdateCheck[229] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.NetworkUtility"></bundle>
24/12/2010 16:26:53 SoftwareUpdateCheck[229] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.Terminal"></bundle>
24/12/2010 16:26:53 SoftwareUpdateCheck[229] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.DiskUtility"></bundle>
24/12/2010 16:26:53 SoftwareUpdateCheck[229] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.SystemProfiler"></bundle>
24/12/2010 16:26:53 SoftwareUpdateCheck[229] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.RAIDUtility"></bundle>
24/12/2010 16:26:55 Software Update[269] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.NetworkUtility"></bundle>
24/12/2010 16:26:55 Software Update[269] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.Terminal"></bundle>
24/12/2010 16:26:55 Software Update[269] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.DiskUtility"></bundle>
24/12/2010 16:26:55 Software Update[269] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.SystemProfiler"></bundle>
24/12/2010 16:26:55 Software Update[269] PackageKit: Missing bundle path, skipping: <bundle id="com.apple.RAIDUtility"></bundle>
24/12/2010 16:28:14 SoftwareUpdateCheck[229] Downloading "iTunes"
24/12/2010 16:28:47 SoftwareUpdateCheck[229] Background check cancelled by user-initiated update.
24/12/2010 16:28:47 SoftwareUpdateCheck[229] Auto-download of "iTunes" SUCCESSFUL.
24/12/2010 16:28:47 com.apple.launchd.peruser.501[215] ([0x0-0xd00d].SoftwareUpdateCheck[229]) Exited with exit code: 102
24/12/2010 16:50:06 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:50:06 com.apple.WindowServer[84] Fri Dec 24 16:50:06 Jeremy-Gordon-Flowerss-MacBook-Pro.local WindowServer[84] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
24/12/2010 16:50:39 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:51:45 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:52:17 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:52:53 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:53:25 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:55:44 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:56:39 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 16:57:05 com.apple.WebKit.PluginAgent[344] Debugger() was called!
24/12/2010 17:00:45 com.apple.WebKit.PluginAgent[344] Debugger() was called!
Message was edited by: gr8fanboy - fixed os version was 10.6 at this point

try this idea: Do a leopard install to an external disk then do a Disk Utility "restore" function to that clean partition. So you restore from the external to the internal partition. Should leave Bootcamp untouched.

Error after fresh install

Hi
I've just installed NetPoint on a second machine and getting the following error:
==========================================================
The path '/burhouse/App_GlobalResources/' maps to a directory outside this application, which is not supported.
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.HttpException: The path '/burhouse/App_GlobalResources/' maps to a directory outside this application, which is not supported.
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
==========================================================
Any ideas anyone? No other settings have been changed, its a fresh install. Thanks in adavance. Andy

Hi Andy,
I'm not sure what this /burhouse/App_GlobalResources is for, I may be wrong but I don't think it's part of Netpoint.
What you should do is check that there is a web.config file in the actual directory for Netpoint in IIS, if so, edit this and remove any reference to "burhouse/App_GlobalResources" in it. If not, copy the wwwroot's web.config into the netpoint website folder and do the same.
I've noticed that sometimes netpoint does not create a web.config file in the correct location so you end up using the IIS website root web.config, which could have references to all other kinds of stuff (like other web applications) in it.
Hope this helps.

[SOLVED]glibc-error after fresh install

Hi,
I've performed a fresh installation of Archlinux and up to the point where I run the pacman -Syu command everything is going well.
It is then that I receive the infamous glibc-error so I followed the instructions on the wiki. However, when I enter the pacman -Syu --ignore glibc command,
I still receive an error for pacman itself needs to be updated first. The problem is that glibc is a dependancy of pacman.
The exact output of the "pacman -Syu --ignore glibc"
warning: ignoring package glibc-2.16.0-2
warning: cannot resolve "glibc>=2.15", a dependancy of pacman
On the wiki I also found a link (http://pkgbuild.com/~allan/glibc-2.16.0 … pkg.tar.xz) to a previous version of glibc, but even then the errors remain.
error: failed to commit transaction (conflicting files)
glibc: /usr/bin/tzselect exists in filesystem
glibc: /usr/sbin/zdump exists in filesystem
glibc: /usr/sbin/zic exists in filesystem
Any help would be appreciated. Thanks!
Last edited by VenomGameworld (2012-07-23 13:19:04)

http://allanmcrae.com/2012/07/updating- … e-install/

[SOLVED] systemd-udev error after fresh install

I downloaded the last arch install medium (2012-11-01), the installation on my laptop was OK, (just arch as only OS), I use the same CD to install it on my desktop.
I have windows xp and arch (dual boot) after install arch on my desktop, grub boots just fine, but I ran into the emergency console of systemctl, ctrl + D give me this:
"systemd-udevd[805]: worker [835] did not accept message -1 (Connection refused), kill it" over and over again
and then, the emergency console again.
here is my fstab
http://pastebin.com/2Qg8Qa8X
this is the log (everything is ok before the hard drives)
http://pastebin.com/Ce5nEWNn
Last edited by helenaryuu (2012-11-05 02:30:49)

I install the ntfs-3g and ntfsprogs packages installed via live CD [pacstrap /mnt ntfs-3g ntfsprogs]
sorry about that

Can not start/stop fullfilment server after fresh install

Can not start/stop fullfilment server after fresh install
Product: e-business suite (11.5.9)
Platform: Win XP 5.1 (SP2)
We have performed a new installation of ebusiness suite in our windows platform.
Installtion went with out any problem.
But we can not start/stop the fullfilment server. While trying to start/stop the server we are getting follwing error message:
c:\oracle11i\prodcomn\admin\scripts\PROD_03274019ih\jtffmctl.cmd start
script returned:
C:\oracle11i\prodcomn\admin\scripts\PROD_03274019ih>echo off
You are running jtffmctl.cmd
Mon 13/09/2004
01:46 PM
"Starting Fulfillment Server for "PROD" on port "9300" ...\n"
"Error returned while running OUI"
ERRORCODE = 1 ERRORCODE_END
.end std out.
Class not found: oracle.apps.jtf.fm.engine.processor.Processor
Please let us know how to fix this issue.
Regards, Kunal

edit the jtffmctl.cmd and make sure that it point to the correct java path, alse try to use java 1.4.1

Satellite L750 - No bootable device error at start-up

I am getting a No Bootable Device error when trying to start my Satellite L750/755.
Before I try any recovery, is it possible to remove the HDD and connect it to my other PC so that I can get all my photos, music, etc. off it. If so what do I need.
I did this on my old desktop, and bought a HDD caddy with a USB connection, so the HDD just looked like an external drive.
Many Thanks
Tim

Yes, you can remove HDD and connect it to your other notebook/PC using external USB HDD enclosure. Using such enclosure you can connect your HDD as external device that should be recognized and listed in Windows Explorer so you can have full access to all your saved data.
Back-up all your data and put the HDD back in your notebook.
Usually if there is no some hardware problem you can start your notebook and press F12 to enter boot menu. When the boot menu is shown on the screen you can put recovery disc info optical disc drive, choose CD/DVD drive and press ENTER button. After doing this optical drive should start to read disc and start to copy data to the HDD.
What you can do before you start to use recovery disc is to enter BIOS and set it to default settings.
Please try all this and send some feedback.

Successfully partitioned but receive 'no bootable device error'

Successfully partitioned late 2007 macbook with bootcamp 4. When I turn on my mac I get the 'no bootable device error.' I tried the advice of only having in the disc I want to install from but still no success. If I restart and hold down 'option' I only see Mac OSX and Recovery mode as options. I tried inserting a disc at that point, but its still not working.
I have a USB with the windows 7 iso install file on it, DVD with the iso file in the packed version, and a second DVD with the contents removed from the iso file.
Not really know which one would be best to use so I've been trying all of them.
I'm also running Lion if that is any additional help. Thanks for any assistance!

I'm not sure how I'm going in circles. The problem I was having was "Now I have the issue where the keyboard and touchpad don't work in the Windows 7 installation."
Anyway, I tried a Windows 8.1 install, and that worked perfect. So not sure what the problem is, but I'll just go with Windows 8 to solve my problem. Thanks for your help.

Netflix plug in error after lion install

What is the fix for Netflix plug in error after lion install?

I reinstalled the plugin from a Netflix email, still get this problem:
I don't have private browsing on, by the way.

Getting "No Bootable device" Error Message

I bought my daughter a new Satellite Laptop earlier in the spring (April 10th) and am having an issue trying to get it to start. Its a C55D-A5120 (S/N XXXXXXXXX P/N PSCFWU-03H02X) and I'm having truble just trying to get help from Toshiba. I originally had registered the laptop when I set it up for her out of the box. I followed every step during the initial start up process but appraently the registration didn't take with Toshiba. The last 3 laptops I've purchased have been Toshiba due to boycotting Dell for their shady business practices with product support. I'll be buying another laptop in the spring and this could very well determine what brand I buy. I live and die by customer service in my line of work and expect "reasonable" service.
Today I called technical support and got the run around from a young lady who said it hadn't been registered but she could help me with that. Okay, good. Umm, no. She said she couldn't register it for some error widow that was popping up on her screen. She said she'd have to transfer me to the warranty department, Okay, good. Umm, no. Warranty was having some technical issue and it hung upon me.
When I originally set up the machine, I had made a full recovery disc but put it on a flash drive. Leave it to a teenage girrl to not be able to find something I said we hopefully wont need but remeber where you put it. That didn't work. Okay, get on Toshiba's website and followed the directions for accessing the recovery section on the HD. Pushing the zero button (either one- also the F2 key does the same thing) and the power button makes it start powering up for about 1 second nad then goes completely dead. Nothing. Without holding any keys, the Toshiba flash sreen comes up and before the Windows boot screen comes up, I get the "No bootable device" error message. It absolutely will not go past that using any method shown anywhere. This is with the a/c adapter plugged in.
The lady I spoke with couldn't tell me if the machine was under warranty or not. I was under the impression the hardware was covered for 1 year. Seems I have a completely dead HD but I'm not the expert. I did remove the battery, the RAM to ispect and clean the conductr strip, same with the HD. That's about where my comfort level ends for the hardware. I hate to spend $40 on a recovery CD if the HD is dead, I can't get into the BIOS to swap what it boots off of. That tells me I have a hardware issue, not a software issue. Is there not a Toshiba warranty service center that can honestly tell me what is going on with this machine?
Any suggestions? I've tried to include pertinent info here. I don't have hours to spend trying to get this fixed. What are my choices? I've been very happy with my virtually identical machine.
Mark
[Moderator edit to remove serial number.]

Hi Peter,
Thanks for the reply.
No, I had already ran across that page and tried that. It won't let me submit it unless a attach a file with a copy of the original receipt, and I had given that to my daughter along with the back up flash drive. I'm not 100% certain of the purchase date. The woman I spoke with wouldn't even tell me what the warranty coverage would be on that laptop. I was under the impression it was a 90 day software, 1 year hardware (for defects in materials or workmanship) warranty. She was so nice as to transfer me to a warranty department that was experiencing technical difficulty.
Thanks again for your reply!
Mark

Lenovo G50-30 - "No Bootable Device" error message when trying to install windows 7 via DVD-ROM.

Hi all, Recently purchased a Lenovo G50-30 as a birthday present. After recieving the laptop, I tried putting a fresh install of Windows 7 64 Bit onto it. After changing the BIOS settings to allow legacy booting from the DVD drive and changing OS Settings to Win 7, I noticed I was getting an error reading "No Bottable Device -- Insert boot disk and press any key". After googling for a few hours on how to fix this I am still stumped and nothing seems to work. Has anyone had a similar issue or would know how to fix this?

Hi omegafeggy,
Welcome to Lenovo Community Forums!
Im kind of confused with the sequence.
Have you installed Windows 7 first then change the BIOS or You changed the BIOS first then Load Windows 7.
Thanks
Solid Cruver

Installing Windows 7 on Mac - no bootable device error

Hello,
I recently purchased Windows 7 Ultimate and am trying to install it on my MacPro running Lion and Bootcamp 4.0. I spent the last couple of days looking online at other fourms and YouTube videos to no luck. I installed Windows 7 and can get it to boot successfully using the Option Key when restarting, but only when the Windows 7 disc is in the drive. When the disc is out of the drive I get the following error when booting into Windows: "no bootable device -- insert boot disk and press any key" and basically freezes. Does anyone know how to fix this error?
Thanks in advance,
Chris

I ran Bootcamp, first downloading the the apple install files for windows and then creating the partition. I choose to partition my hard drive 60 gB. Then I installed the 64 bit Windows 7 Ultimate and ran though the standard process, including choosing the reformat to NTFS file system. I then installing Windows using the defaults, and ran thought the defaults. I remember then installing Apple "setup" from the install files I downloaded. I also remember setting the startup disc to "Macintosh HD" in the Windows 7. Basically I ran though the bootcamp installation guide. I sorry if this isn't that technical, I not a techie. If there is more info that helps, let me know.
If it helps my laptop is:
MacBook Pro 15-inch, Late 2008
Mac OS X Verison 10.7.1
Processor 2.4 GHz Intel Core 2 Duo
Memory 6 GB 1067 MHz DDR3
Graphics NVIDIA GeForce 9400M 256 MB
Thanks, Chris

Bootcamp "no bootable device" error while trying to install win7 on imac

Hello everyone,
I'm trying to install my original copy of windows 7 on my iMac 21,5 mid 2010 with mavericks as os.
This is what i do:
With my dvd of windows inserted in my cd/dvd reader I open bootcamp, i make the usb with drivers, i make the partition dedicated to windows and then the iMac restarts automaticcally.
When the iMac boots up a black screen (windowslike) appear saying : "no bootable device insert...etcetc and press any key"
First of all i'm using an external dvd reader because since i've upgraded to mavericks my superdrive stopped working (another big issue i've found out these days).
Then i've also tried making an usb bootable device....same black screen appeared.
I've been searching on the internet for days now without luck.
I believe i've tried everying but this funky situation keeps occourring.
I need to say that I installed windows on my iMac in the past and everything worked just fine, more then fine!
I need help please because i need windows on this machine due to working deadlines.
I'm desperate.
Help.

Hello everyone,
I'm trying to install my original copy of windows 7 on my iMac 21,5 mid 2010 with mavericks as os.
This is what i do:
With my dvd of windows inserted in my cd/dvd reader I open bootcamp, i make the usb with drivers, i make the partition dedicated to windows and then the iMac restarts automaticcally.
When the iMac boots up a black screen (windowslike) appear saying : "no bootable device insert...etcetc and press any key"
First of all i'm using an external dvd reader because since i've upgraded to mavericks my superdrive stopped working (another big issue i've found out these days).
Then i've also tried making an usb bootable device....same black screen appeared.
I've been searching on the internet for days now without luck.
I believe i've tried everying but this funky situation keeps occourring.
I need to say that I installed windows on my iMac in the past and everything worked just fine, more then fine!
I need help please because i need windows on this machine due to working deadlines.
I'm desperate.
Help.

No Bootable Device error after fresh install

Similar Messages

Maybe you are looking for