No internet access Available from wifi

I am very annoyed that i pay for a service and cannot have access to the internet Using wifi.. "no internet connection available"I have tried it on both my Xperia Z2 and Samsung S5 with no luck.. It is that bad that i'd have to say that i can only use it about 2 percent of the times.. YES 2 PERCENT.. not a typo.. This is bloody ridiculous..I have done a lot of research on the net and it seems to be an Android problem.. Spotify works on my PS4, WII and Laptop but on none of my androids.. The mobile is the main reason i joined/suscribed as a premium member..
No point asking me to try to fix it myself as i already..1.. uninstalled/reinstalled software,2... Turned on/off /on the phone,3... Restored both phones,4... Taken both phones to my mate's house Wifi and5...Used the community service you guys offer and still with the same "No internet issue" Please advise real fix for this issue as i am spending my well earned money on a service that i am having extreme difficulty using... You should also have a phone number for direct contact so that WE can contact you and have all our problems/issues fixed 1 on 1.. Awaiting a genuine response

Same here. Have had this problem since the latest updates (latest one has still not fixed it) and there's no solution provided by spotify people anywhere. This is unbelievable. "no Internet connection" when using spotify on wifi, on my nexus 5, nexus 10 and galaxy s3. when going to cellular data it works fine.
FIX THIS, IT'S BEEN A MONTH

Similar Messages

  • IPhone 5 no internet connection away from WIFI

    I have no Internet connection away from WiFi while using 3G on my iPhone 5. This didn't use to be a problem. I now get the message <your phone is not connected to the Internet.>
    I have data roaming/ cellular data enabled. Can anyone offer help as I may have changed a setting somewhere without knowing?
    Grateful for any help please!
    Thx

    Have you recently changed your SIM card to that of another provider? If so, you may need to set your APN settings - Settings/Mobile/Mobile Data Network (on UK phones).  If not, then seek advice from your service provider because it's very likely to be connected with your APN settings.
    The other option is to search the Internet for the APN settings for your service provider. The information should be readily available.

  • Ethernet cable internet access only No WiFi in hotel MBA user

    Am assuming I need to carry my own Airport Express with my MBA as I am in a hotel that has ethernet cable internet access only - no WIFI? If so, what do I need to know about how to get MBA and Airport Express to "talk" to each other in these types of hotel situations?
    Thanks for your assistance
    PEM

    Hi Elegba,
    Curious... did you consider the USB Ethernet adapter for the MacBook Air? A whole lot cheaper of a solution for a hotel without WiFi. Not to mention, I've found (after initially struggling to justify the purchase) that I use mine more than I originally thought.
    However, to answer your question. You'll connect the Ethernet to the AirPort Express Base Station and configure it via the AirPort Utility on your MacBook Air. It's very straight-forward and you'll be creating a wireless network. You may need to first get setup with your 'in room' connection, though, I know most hotels have a proxy connection for web access. While you should still be able to setup the Express, it's just something to keep in mind.

  • Is it possible to be connected with a 3G modem for internet access and a WiFi router for printer sharing at the same time?

    For our only internet access we have a 3G wireless modem. I have since purchased a WiFi printer and router to connect all the comptuters to in the house. The PCs have no problem with using both the 3G connection and the WiFi signal at the same time to print, however, the MacBook Pro will not connect to the 3G network and the router, it will drop the internet access from the modem and attempt to connect via WiFi (which has no internet access). Is there a solution that is available to remedy this? I attempted to create an adhoc printer network, however, the macbooks again will not print off of this, only the PCs. And I'm getting a bit frustrated overall with this.

    The 3G wireless modem is on one of the PC's correct?
    Why don't you pass the Internet through the Ethernet port to the router via Cat5 cable, then have that transmit a Wifi signal that everything else can use, then connect the printer to the router for print sharing?
    You would have to turn off the wifi on the comptuer with the 3G modem as it's physically connected to the router and can't connect to the other machines as they are all connected to the router for sharing.
    The Mac has the ability to pass, Internet Sharing in the System Preferences.
    Do you have software for the Mac to run the 3G modem?

  • "No internet access" on Guest Wifi

    We upgraded our router the other day, we made a backup as well as a txt copy of the config file for copying in various commands to the new router .
    We have a Secure wifi for employees and a Guest wifi for visitors. We have a server doing the DHCP(10.27.131.8) for both the secure (10.27.131.0 network) and for the Guest (10.26.131.0 network). The Secure wifi is working as it should be - the Guest however is not. Visitors can connect and get a valid IP address from the 10.26.131.0 network but have no internet access. Everything else has stayed the same - no changes to the AP's.
    Again we copied the config from the old to the new with a few minor changes but nothing that should effect the Guest wifi.
    I did an ipconfig after connecting to the Guest Wifi and I can get a correct IP address 10.26.131.214, Default GW: 10.26.131.1.
    I enclosed the config from my router is anybody could shed some light,
    Thanks in advance.
    Building configuration...
    aaa new-model
    aaa authentication login default line local
    aaa authentication login vtymethod group tacacs+ line
    aaa authentication login conmethod line
    aaa authentication login httpmethod group tacacs+ local
    aaa authentication enable default enable group tacacs+
    aaa authentication ppp default none
    aaa authorization config-commands
    aaa authorization exec default local group tacacs+ none
    aaa authorization commands 1 default group tacacs+ if-authenticated
    aaa authorization commands 15 default group tacacs+ none
    aaa accounting exec default start-stop group tacacs+
    aaa accounting commands 1 default start-stop group tacacs+
    aaa accounting commands 15 default start-stop group tacacs+
    aaa accounting network default start-stop group tacacs+
    aaa accounting system default start-stop group tacacs+
    aaa session-id common
    resource policy
    ip subnet-zero
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 10.26.131.1 10.26.131.100
    ip dhcp pool guest
       network 10.26.131.0 255.255.255.0
       dns-server 208.67.222.222 208.67.220.220
       default-router 10.26.131.1
       domain-name guest.X.xxx
    interface Tunnel3
     ip address 172.17.3.2 255.255.255.0
     ip mtu 1400
     ip tcp adjust-mss 1360
     tunnel source 12.xx.xx.xx
     tunnel destination 19x.xx.xx.xx
    interface Tunnel55
     ip address 192.168.66.10 255.255.255.0
     ip accounting output-packets
     ip accounting access-violations
     ip mtu 1400
     ip tcp adjust-mss 1360
     tunnel source 12.xx.xx.xx
     tunnel destination 12.xx.xx.xx
    interface FastEthernet0/0
     ip address 12.xx.xx.xx 255.255.255.248
     ip nat outside
     ip route-cache flow
     duplex auto
     speed auto
     service-policy output physical
    interface FastEthernet0/1
     description CONNECTION TO SW3
     no ip address
     duplex auto
     speed auto
     service-policy output physical
    interface FastEthernet0/1.1
     description LAN
     encapsulation dot1Q 1 native
     ip address 10.27.131.254 255.255.255.0
     ip flow ingress
     ip flow egress
     ip nat inside
     no snmp trap link-status
    interface FastEthernet0/1.20
     description GUEST NETWORK
     encapsulation dot1Q 20
     ip address 10.26.131.1 255.255.255.0
     ip access-group 101 in
     ip helper-address 10.27.131.8
     no snmp trap link-status
    interface FastEthernet0/1.200
     description Phone VLAN
     encapsulation dot1Q 200
     ip address 10.5.2.254 255.255.255.0
     no snmp trap link-status
    interface Serial0/0/0
     no ip address
     shutdown
    interface Serial0/2/0
     no ip address
     shutdown
    interface Serial0/3/0
     no ip address
     shutdown
    ip classless
    ip route 0.0.0.0 0.0.0.0 12.xx.xx.xx
    ip route 10.5.5.0 255.255.255.0 10.5.2.1
    ip route 10.10.0.0 255.255.255.0 172.17.3.5
    ip route 10.10.200.0 255.255.255.0 172.17.3.5
    ip route 10.25.131.0 255.255.255.0 192.168.66.20
    ip route 10.27.129.0 255.255.255.0 172.17.3.5
    ip route 10.27.130.0 255.255.255.0 172.17.3.5
    ip route 140.xx.xx.xx 255.255.0.0 172.17.3.5
    ip route 192.168.2.0 255.255.254.0 172.17.3.5
    ip route 192.168.99.0 255.255.255.0 172.17.3.5
    ip http server
    ip http authentication local
    ip http secure-server
    ip nat inside source list 2 interface FastEthernet0/0 overload
    access-list 2 permit 10.27.131.0 0.0.0.255
    access-list 2 permit 10.25.131.0 0.0.0.255
    access-list 2 permit 192.168.66.0 0.0.0.255
    access-list 2 permit 10.14.0.0 0.0.0.255
    access-list 2 permit 10.5.5.0 0.0.0.255
    access-list 2 permit 10.5.2.0 0.0.0.255
    access-list 5 deny   10.27.131.123
    access-list 5 permit 192.168.2.0 0.0.0.255
    access-list 5 permit 10.27.131.0 0.0.0.255
    access-list 5 permit any
    access-list 101 permit tcp any host 10.27.131.8 eq 67
    access-list 101 permit udp any host 10.27.131.8 eq bootps
    access-list 101 permit ip 10.26.131.0 0.0.0.255 host 10.14.0.6
    access-list 101 deny   ip 10.26.131.0 0.0.0.255 10.0.0.0 0.255.255.255
    access-list 101 deny   ip 10.26.131.0 0.0.0.255 172.16.0.0 0.15.255.255
    access-list 101 deny   ip 10.26.131.0 0.0.0.255 192.168.0.0 0.0.255.255
    access-list 101 deny   icmp 10.26.131.0 0.0.0.255 172.16.0.0 0.15.255.255
    access-list 101 deny   icmp 10.26.131.0 0.0.0.255 10.0.0.0 0.255.255.255
    access-list 101 deny   icmp 10.26.131.0 0.0.0.255 192.168.0.0 0.0.255.255
    access-list 101 permit ip 10.26.131.0 0.0.0.255 any
    access-list 102 permit icmp 10.25.131.0 0.0.0.255 any
    access-list 102 permit ip 192.168.66.0 0.0.0.255 any
    access-list 102 permit ip 10.25.131.0 0.0.0.255 any
    access-list 102 permit ip 10.27.131.0 0.0.0.255 any

    Hi,
    I also apologize for my late answer.
    I appears your ACL 101 that filters traffic entering the Fa0/1.20 is not correctly written to allow DHCP requests to be processed by the router. The attempt has been made - but it is not correct. In particular, check out the second entry in the ACL 101:
    access-list 101 permit udp any host 10.27.131.8 eq bootps
    It allows all DHCP messages that are already targeted to 10.27.131.8, the DHCP server. However, such targeted DHCP messages may be used by clients only after they know who the DHCP server is in the first place. Until then, the requests are targeted to 255.255.255.255 and sourced from 0.0.0.0. Such packets are not allowed by any entry in the ACL 101 and are therefore dropped even before the DHCP Relay Agent can process them. That would explain why your clients actually cannot obtain IP address via DHCP in VLAN 20.
    We need to add the following entry immediately before or after the existing second entry in the ACL 101:
    access-list 101 permit udp any host 255.255.255.255 eq bootps
    You may accomplish this by the following sequence of commands directly pasted into the global configuration:
    ip access-list resequence 101 10 10
    ip access-list extended 101
    15 permit udp any host 255.255.255.255 eq bootps
    end
    The first line will cause the individual entries of the ACL 101 to be internally numbered, starting with the sequence number 10 and incrementing by 10 for each subsequent entry. The second line enters the ACL 101, treating it as a named ACL, allowing us to use the extended editing features. Finally, the third line starting with the sequence number 15 will cause the entry to be added between the existing first (seq no 10) and second (seq no 20) entry. It must be entered including the sequence number, otherwise the line will be added at the end of the ACL.
    Would you mind trying out this modification? The former corrections with the NAT I have described earlier must be applied as well.
    Best regards,
    Peter

  • Just got a second hand ipod touch from my grandson dont know much about them, want to get onto the internet while away from wifi can the ipod touch do this such as gps any help would be appreciated.

    Hi i have just had a second hand ipod touch from my grandson but he is not very helpful with it.
    Can u get onto the internet when not using wifi such as in the car or such like. my phone uses 3G  can you use gps or anything.
    i really do not know anything about ipods
    Any help would be appreciated.

    "Can u get onto the internet when not using wifi "
    No.
    it connects to the internet ONLY via wi-fi

  • HT201334 How does one set up profile manager on a completely closed network with no Internet access available or even possible?

    I need to set up Profile Manager on a completely closed network that has no Internet access at all. I can sneaker-net files into the network if I need to.
    Profile Manager (and Lion Server in general) seems to need outside access to complete setup and I've been unable to find any meaningful answers.
    Does anyone any any ideas?
    Thanks to all

    you could try it without enabling apple push notifications in server
    you wont' be able to push out profiles without enabling apple push notification
    but users could download them, or you could install manually, e-mail etc

  • Can I control Internet Access Centrally from the H...

    Hi,
    Is it posible to block access to certain categories of internet web sites directly from the hub using OPENDNS or any other method?
    I can set access times using the bthomehub, but I would like to be able to check/limit the material they are able to access as well. 
    Can I apply this control centrally from the hub and not have to set up the control on individual machines in my home, as I would if I use the BT Netprotect.
    My kids access the internet with ipads and phones and so a central solution from the hub would be ideal.
    Thanks
    Solved!
    Go to Solution.

    Hi geresy,
    Welcome to the Forum and thanks for posting. This might help. Let me know if it does.
    Cheers
    David
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • Internet access works from one jack only

    I recently moved to a new apartment that has three phone jacks, the phone works fine on all three but my router will work only from the jack where the main feed comes into my apartment.
    I have tried different cables, rebooting, unplugging, etc. Do I need to call for a technician?

    It is possible the installation has a filter in the network box for the phone lines while the line to the jack which has the dsl service is unfiltered.

  • Broadband internet access away from home (powerbook G4)

    I've cracked this when I stay with friends who have macs, but how do I go about it when I visit those with pcs? What do I do in Network Prefs, and do I need a special cable?

    Depending on what service your friends have.
    In System Preferences and NETWORK, You simply choose your method of connection, Wireless, Ethernet< or Internal Modem(Dial-Up).
    Next many Internet Services require authentication and you need to check with your friends to see if this is the case with there connection, If not then you will just fire that baby up and log on.
    Be sure you check with your friends, and make sure there isn't anything special you need to log on with.
    Cheers Don

  • Iphone6 touch id stops internet access both wifi and cellular

    iPhone 6 64GB iOS 8.0.2 Verizon - With Touch ID on (at least one fingerprint is configured), there are times when I depress HOME to wake the device and then try to use the fingerprint reading service, internet access stops both on wifi and cellular. Turning wifi off and on doesn't help. The wifi signal shows as OK. No subsequent internet access on either wifi or cellular. Have to restart the device (I hold the home and power buttons together until the Apple logo displays).
    Right now, it is OK to not use Touch ID. In fact, since I specify how long to wait before locking the device it is actually more convenient to not use Touch ID.
    However, when Apple Pay is available this will be a significant problem.
    Any advice? Thank you.

    I have not verified this, but I have read that the ios 6 ipad uses either the cell network or the wifi network, but not both at the same time.
    You should be able to test this.
    I'm not enough of a network tech to know if you could get this to work, but there are mifi devices that do wifi to cellular. 
    Here is one example:
    FreedomPop provides 500meg of free 4g cellular data per month!  You do need to buy a wireless device at $39. There are ways of getting bonus megs.  One gig of addition data costs $10 per month.  I used about 10megs per hour of internet surfing.
    When signing up, you need to be careful with your selections.  On some screens, the free option is a small link below the large button.  FreedomPop employs a Pavlovian Dog < Operant conditioning > thing of getting you used to clicking on the large button then they change the large button to a paid add-on.
    Once you setup your account, you need to go to your account options screen to turn off automatic paid data download once you exceed your quota.
    The performance seems about like my DSL connection.
    http://www.freedompop.com/offers.htm?experience=organic.default
    http://www.freedompop.com/coverage
    Get it before they go broke.
    Robert

  • TS1398 As a truck driver, I don't have internet access, my cell phone doesn't support Apple yet either,,, How can i gain internet access on the road if I'm rolling and not in a stationary place for wifi?

    I recently purchased an i pad and have the internet at home, I am also a truck driver and once i leave home, I won't have the internet unless I stop close to where there is wifi, is there anything out there that I can purchase so I will have the internet at all times

    I purchased a Verizon MIFI 2200 mobile hotspot with my forst generation iPad almost tow years ago so that I could have internet access with my WiFi only iPad and my iPod Touch. All in all it is pretty reliable but as varjak paw stated above...
    "Either of course will be dependening on your being in a location where the carrier provides cell coverage".
    Like my cell phone - there are locations where the MIFI doesn't play nice with the cellular networks and it may struggle to find a good signal. On the other hand, sometimes my connection zips along quite nicely. Just keep that in mind - if and when you decide to purchase a mobile hotspot.

  • Can I create a wi-fi network on my macbook and still connect to the internet via an actual wifi point?

    Hi,
    I got TrakProDJ from the app store and installed it.
    It allows me to control a DJing software with my iPad by setting up a network via Wifi Symbol in Toolbar>Create Network...
    The problem with this is the network I create isn't based in the internet--it's just a wifi link between my laptop and iPad.
    I'm sure I'll get asked to play songs I'll have to look up on youtube, so how is it possible that I can maintain my wifi network connection on my macbook and create an access point for my iPad to use to communicate with my laptop (to control the DJing software)?
    I'll really appreciate any help I can get!
    Thank you!

    You cannot use both an ad-hoc network and a normal ap based one with any wireless device.  Your only solution is to use a wired Internet connection to do so on the laptop, that way you use that for Internet access and your wifi for the ad-hoc network the app requires.  You might want to contact the developer of that app and find out why they limit the setup to just an ad-hoc wifi setup.  Seems that if all it requires is just a network connection to the laptop, they could simply use any existing network connection as long as both devices can see each other on it.  Either that or also give the user the option to use Bluetooth for it if they have the higher version of hardware to support the necessary data exchange.

  • Lost internet access

    I have lost the internet access strip from my startup page--no address box, no google box, no
    buttons. What do I do?

    It sounds to me like have hidden the Toolbar.
    If it is available in the View menu, click on View > Show Toolbar.
    Note that the keyboard shortcut to show/hide the Toolbar is Command-Shift-\ . (It's listed in the menu as Command-| , but at least on a U.S. keyboard that requires typing Shift and the backslash key. ) It's not too difficult to accidentally type that shortcut and hide the Toolbar without realizing it.
    Message was edited by: Rachel R

  • I don't have a DSL or cable modem to access the Internet ... just a mobile WiFi (there is no cable available at our house). How do I connect my Time Capsule to the Internet via the mobile WiFi?

    I don't have a DSL or cable modem to access the Internet ... just a mobile WiFi (there is no cable available at our house and the mobile WiFi is our only option). How do I connect my Time Capsule to the Internet via the mobile WiFi?

    LOL!!
    I am in Australia and the ISP... I think both the main ones would fit your description to a T.. big T in particular.
    Your router is really unsuitable.. if it is only wireless and no ethernet.. just buy an ethernet one.
    Do a search on ebay.. 3g router.
    But you can get the TC to join a wireless network.
    It is a non-standard setup that Apple will not support.. the option is hidden.
    If you are on Lion download the 5.6 utility. Go to the wireless set up page and hold down the option key whilst selecting wireless mode.. a new option, join will appear. You can then put in the ssid and passkey of the 3g router.
    But please note the end result of this setup..
    very slow speed. The TC is now a second wireless hop from your clients.. this will halve the speed.
    In this mode the ethernet are deactived.. for reasons only Apple know, they decided you should not use ethernet when doing this.

Maybe you are looking for