No sound from speaker after upgrading?

I just upgraded my iBook Clamshell 466 SE Graphite with more memory and a new 60GB 7200 RPM Hitachi hardrive. I also upgraded from Panther to Tiger with a Black Retail DVD.
First, I installed the memory and then the following day, I installed the hardrive and OS.
After installing the hardrive myself (30+ steps with the ifixit.com instructions) and installing Tiger, I no longer have sound through the mono speaker although it was working perfectly before. It took me about an hour to carefully and meticulously disassemble and reassemble my laptop while removing tabs, screws, cables, etc. and being organized about it.
I'm not sure why I no longer have speaker sound but the headphone jack still works with sound. I double checked that the speaker cable was properly connected on both ends. I don't think it's a ciruit board issue since sound is still being delivered through the headphone jack.
Is there a way to run some sort of diagnosis as to my sound problem? How do I check my firmware version and is it possible that I need to update? I appreciate any help in advance...

I always try to leave the speaker cable connected to the logicboard (as well as the HD cable) during the installation of the new HD - simply remove the adhesive foil and let it slip through the hole in the EMI shield.
Otherwise you have to wrench at the cable to come out, and that might be the problem.
For testing purposes, try to connect a set of earphones with bare cable heads to the end of the cable or directly to the solder joints of the integrated speaker.

Similar Messages

TS5180 No sound sound from speaker recently upgraded to iOS7.0.2

No sound sound from speaker recently upgraded to iOS7.0.2

I have this problem too, .
I upgraded my iPhone4 today. Immediately my phone is defunct, and I cannot find any workaround listed anywhere online for the phone, only for the iPad2.
Reset All Settings as per iPad2 advice had no effect except to make me have to re-enter all my settings again.
The volume bar is greyed out in Music settings, and has no visible point on the bar where the volume is defaulted to.
The greyed out bar doesn;t change when the volume buttons are pressed.
However, sometimes the ringer volume logo pops up and changes when I do this, but not always.
However when I call the phone, the ringer is always at full volume, as it was immeditely prior to upgrade.
When I press either up or down volume button the ringer silences completely, immediately, and cannot be resurrected by any manouvers.
Only another call will make the ringer sound.
When I answer the call, the phone is mute though the mute button is not highlighted.
Toggling the mute makes no difference.
Selecting Speaker mode makes no difference - it is mute.
Selecting either up or down volume buttons has no effect.
Using the Jack output is silent.
I cannot hear music, youtube videos, BBC news clips, or any alerts.
Vibrate is still working.
Trying not to get angry again with another Apple "UPGRADE" disaster - but frankly - I can't even make or receive a phone call - is this fixable???
PLease does anyone know how to dothis?
BTW, being iPhone 4, of course the Home button doesn;t work, so anything involving the Home button must be able to work with the Accessibility Home Button software.
Desperately: How do I downgrade to previous iOS 6 last version?
Grim.
Akilia.

Satellite a505-s6030 suddenly no sound from speaker

hi every body
can any one help me with my problem , i lost sound from speaker but there is sound through headphone
my laptop is satellite a505-s6030 with windows 7 64bit and harman/kardon speakers
i tried every thing like:
- reinstall drivers and chipset driver
- reload last system image
- installing new windows 7
there is no sound at all
the strange thing is beeb sound from speaker work during booting but disconnect when windows login
is my speaker damaged or not
and what i shall do
please any one can help me ?
Solved!
Go to Solution.

Hi PhiPsiVol354
corrupted CMOS occurs when there is strange problem happen to laptop
Not necessary that corrupted CMOS prevent laptop from booting , may laptop boot successfully but CMOS not recognize the component of your laptop like sound card or video card or any other part specification .
so you need to load default BIOS setting to CMOS , but it fails to load default BIOS because corrupted CMOS needs to be cleared first before loading default BIOS.
this work (clear CMOS) is done manually by connect jumbers together inside laptop motherbaord
OR
By using software like HIREN BOOT CD ( this is famous Repair cd ).
follow this steps:
1- Search internet to find and download (HIREN BOOT CD) cd image. or ask any friend may he has that cd
   ( prefered to choice v.9.7 or v.10)
2- If you download (HIREN BOOT CD) from internet ,Burn that cd image to cd with low writing speed.
3-Insert that cd into cd driver ,at laptop startup press F12 to boot from cd .
4-Menu appear , show:
   -boot from hard drive
   -boot from cd
   -load mini windows xp
select second option ( boot from cd)
5-another menu shows with numbers browse to find (BIOS/CMOS TOOLS)
enter that section you will find many tools select from them (KILLCMOS).
6-Run (KILLCMOS) tool , it will show confirmation message ( ARE YOU SURE WANT TO CLEAR CMOS),press arrow button to select (YES) , after clear cmos done , press ESC button to exit ,then press (ALT+CTRL+DEL) to reboot system , and immediately enter to BIOS setting by press F2 .
7-Load default setting by press (F9) and save change and exit (F10).
8- the system restart and enter to windows .
9- If process failed to solve the problem , Repeat it again.
Good luck
I hope this will solve your problem.

I lost hundreds of pictures from iPhoto after upgrading to Mavericks

I lost hundreds of pictures from iphoto after upgrading to mavericks. does anyone know why or how to retrieve them. i cannot find them on time machine either.

and
Why do you think you have lost "hundreds" of pictures?
What exactly are you seeing
You can try Back up your iPhoto library, Depress and hold the option (alt) and command keys and launch iPhoto - rebuild your iPhoto library database
LN

No sound in firefox after upgrade to Ubuntu 10.04

no sound in firefox after upgrade to Ubuntu 10.04. Youtube and Vimeo are both affected. Have sound in Banshee and MPlayer.
== This happened ==
Every time Firefox opened
== After latest upgrade to 10.04

Sorry, can't help you much with Ubuntu issues, I am a new Ubuntu user myself; except that you have two versions of Flash appearing in your Plugins Installed listing. Not sure if it will solve that particular problem, but you need to delete the Shockwave Flash 9.0 r124 version.

Cannot open survey files from email after upgrading SAP gui to 720

Cannot open survey files attachments from email after upgrading SAP gui from 640 to 720.
Tried uninstalling & reinstalling but still error persists,
Error is : cannot split connection string: /h/server name/s/sapdp00 ( from SAP GUI security )
Please advise.

Can't say I have seen this error before but if it is pertaining to the new security module within 7.20, which are much more strict then 6.40, I would look under the SAP GUI configuration options. Focus on Security > Security settings.
There are pages and pages of rules which can be defined.
A test could be to disable all of them on an isolated machine and set them to allow and see if your problem persists. If the error is resolved, it is something in there you need to address.
Regards,
Zecher

How come calendars and contacts vanish from iPhone after upgrade to iTunes 6.1.2?

How come calandras and contacts vanish from iPhone after upgrade to iTunes 6.1.2?

Hi, Did you work out a fix for this? All my calender dates (past & future) and the last 12 months of new contacts gone!!!! And yes i too back up regularly.
Previously when the great 5 upgrade happened, i did loss everything, and although I was doing backups none of that info was relative in an English way. A whole life of important, unreplaceable information gone! Never to be found.
All of my products are apple, but it seems that little people dont matter to them, with no recourse for the damage to my personal or professional life.
Extremly disappointed again!

HT2178 No sound from Doom3 after installed from the App store onto my intel iMac

No sound from Doom3 after installed from the App store onto my intel iMac 10.7.3 Any solutions?

Just just launch the Mac App Store, select the "Purchased" tab and download MainStage or any other application you already bought.

No sound from tv after laptop connected (G60)

Hi
It is no sound from TV, after i connecting my laptop to tv through hdmi cable on hdmi port 1.
However, the image looks ok.
I open the sound control panel, see NIVDIA HDMI OUTPUT SEEMS WORKING, (SET DEFAULT), BUT THE VOLUME IS VERY LOW, AND NO TEST SOUND COMING OUT FROM TV EITHER.
I tried to set up the audio system in NIVDIA control panle under VIDEO AND TV as instruction in HELP of NIVDIA help manual. But i just cannot find the audio system set up.
anyone can help on this,
Very appreciated!
Tnx
My email is
[text removed for privacy]

Try this, it works on my PC:
Connect HDMI cable to TV.
In the Control Panel, select "Sound" by double-clicking it.
Click the "Playback" tab and look for an icon for your television.
Highlight the TV icon and then select "Set Default". A green checkmark should appear on the TV icon.
You should now hear sound from the TV when your HDMI cable is connected, and sound from your PC when the cable is not connected.
Marty
dm4t i5-430M 4GB-RAM IntelGraphics

Lost music from iTunes after upgrading MacBookPro to OS X Yosemite

Lost music from iTunes after upgrading MacBookPro to OS X Yosemite. Has anyone had this problem? How did you re-import all your lost music? My iTunes currently only contains all of the music I have purchased from the iTunes Store but nothing that was burned to my iTunes. All of my music files still seem to be located on my hard drive within the iTunes folder but they did not re-import into the library during the upgrade to Yosemite. Thanx for your help.

Hi OrangeOAK,
Thanks for the question. If I understand correctly, you still have the music on the computer but need to re add it to iTunes. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
Adding music and other content to iTunes - Apple Support
Adding content on your computer to iTunes
iTunes helps you add digital audio and video files on your computer directly to your iTunes library. You can add audio files that are in AAC, MP3, WAV, AIFF, Apple Lossless, or Audible.com (.aa) format. If you have unprotected WMA content, iTunes for Windows can convert these files to one of these formats. You can also add video content in QuickTime or MPEG-4 format to iTunes. To learn how to add these files to iTunes follow the steps below.
Open iTunes
From the File menu, choose one of the following choices:
MacAdd to Library
Windows
Add File to Library
Add Folder to Library
Navigate to and select the file or folder that you want to add
If iTunes is set to "Copy files to the iTunes Music folder when adding to library," iTunes will copy all content that is added to the iTunes library to the iTunes Music folder. To adjust this setting or change the location of this folder, go to the Advanced tab in iTunes Preferences.
Thanks for using Apple Support Communities.
Have a great day,
Mario

Will my text threads be transferred to new 4S from 3GS after upgrade?

will my text threads be transferred to new 4S from 3GS after upgrade?

See this article about the content of a backup: http://support.apple.com/kb/HT4946
Make sure to back up the backup folder before you restore your new phone with the backup of the 3GS. The location of this folder is also described in the article.

Sound effects can't come out from SoundSticks after upgrade to 10.4.4

After upgrading to 10.4.4, the sound effects of OS X, such as emptying trash, iChat effects, etc, doesn't come out from the SoundSticks (first generation, connected via USB), even though I've turned it (effects) to the highest level, and selected to have it come out of the SoundSticks.
The effects are fine if I select Built-in Audio as sound output.

After upgrading to 10.4.4, the sound effects of OS X, such as emptying trash, iChat effects, etc, doesn't come out from the SoundSticks (first generation, connected via USB), even though I've turned it (effects) to the highest level, and selected to have it come out of the SoundSticks.
The effects are fine if I select Built-in Audio as sound output.

IPod touch 4th gen - no sound from speaker dock

After upgrading my 4th gen iPod touch o iOS 5, the speaker dock no longer works. The dock charges the iPod, but iPod still continues to output sound from the internal speaker rather than the speaker dock. My iPhone with iOS 5 works fine on the dock. I have restored the iPod to a fresh state but the problem still persists
What could be the problem?
Thank you

Based on your troubleshooting, it would appear theat iOS 5 on the iPod made the dock incompatible. Have you loked at the dock manufactore's support site?

Clustered listener gets nothing back from APEX after upgrade to 4.1.1

Hi,
I'm not sure if that subject is entirely accurate, but that appears to be the effect we are experiencing. We have had an SR open for this since April and seem to have the engineers stumped. Maybe someone on here has some insight that may help...
Environment: Seven APEX instances
APEX 4.1.1 (problem started after upgrading from 4.0.x) running on an 11g RAC.
Listener version 1.1.3.243.11.40 running on WebLogic 10.3.2.0
Listeners are in 2x clusters on two different WebLogic domains spread over 4 different servers.
Problem:
In two of the apex instances, a couple of days after upgrading to 4.1.1, the listeners starting returning blank, empty pages to the browser. We went through all the usual debugging steps (/i/ directory, connectivity, etc) and nothing fixed the problem. Finally the only thing that fixes the problem is to shut down one of the two clustered WL managed servers running the listeners, reducing the listener to a single instance per APEX instance. Like clockwork, if the second managed server is brought back up, within minutes-to-hours, the listener starts returning blank pages to the browser. Just a couple of days ago, a third apex instance and its listeners has started to manifest the problem and had to be half shut down. We are beginning to think there is a bug in APEX 4.1.1 that deadlocks the listener (or something) when it is clustered...
Other data points:
The listenerAdmin and listenerStatus pages continue to work and report perfect health for all listeners involved.
The APEX management console (p=4550:1) is also affected by the problem, not just apps.
We ran the "apex_verify" script on all problem instances with no errors.
We have hard rebooted all affected servers, with no change in the problem.
This identical environment was running perfectly stable, clustered for many months on APEX 4.0 (and before).
The only thing that keeps our APEX apps running is to run the listeners single instance (un-clustered).
Thanks in advance for any help that anyone can provide on this very annoying problem!
Brian
Edited by: bpoarnet on Jun 12, 2012 12:51 PM

Udo wrote:
So it's somewhere within your WLS setup.Mmm... I won't discount anything, but I doubt it. If that were the case, how could this exact environment have managed to work flawlessly for the past 3 years on these clusters, the listener being upgraded several times through several versions of apex? Only directly after we upgraded apex (not the listener) to 4.1.1 did our troubles start. My suspicion is that there is a bug or a change in 4.1.1 (or maybe 4.1 as we applied 4.1.1 right after 4.1) that has manifested this problem for us.
>
They definitely are not being used equally, but none of them are being slammed. Usage is fairly light in all cases.... which sounds like if there is some kind of load balancing algorithm different from round robin in your scenario.Ahh, I misinterpreted your question. You were asking if the load is balanced fairly between nodes on the same cluster. I took you to be asking if our separate, unrelated apex instances get the same use. So, the answer then is "yes" hits to a single listener WLS cluster do appear to be getting assigned equally to the different nodes, and the clusters are installed as per the documentation with round-robin scheduling.
####<Jun 11, 2012 11:07:31 AM EDT> <Warning> <Socket> <hostname> <server-name> <ExecuteThread: '0' for queue: 'weblogic.socket.Muxer'> <<WLS Kernel>> <1339427251735> <BEA-000450> <Socket 5 internal data record unavailable (probable closure due idle timeout), event received 17>That could probably have a lot of reasons, but none of them is specific to APEX Listener. Google gives a lot of hits ranging from memory issues to missing classes, and ... duplicate configuration parameters, e.g. app names, jdbc pool names, etc.... and of course, I'm not convinced that this has much to do with the problem at hand. It just happened to be in the log at around the time that someone noticed the problem happening in one case.
Could it be your APEX Listener is deployed multiple times on the same node using the same name?Good thought, but definitely no. We figured out that issue a couple of years ago, back when you had to hack the listener WAR file to make it use a non-temporary config.
Lastly, I just want to thank you again Udo for patiently digging into this. We now have three SR's open with Oracle on this (RAC team, APEX team, and WebLogic team) and we have gotten nowhere yet with any of them...

Cannot email photos from iPhoto after upgrade to 10.8

After upgrading to 10.8, I have not been able to successfully eamil photos from iPhoto. I can select the photos, click the email icon, and have Mail open with the photos attached (as expected). But the send button is grayed out, and the newly created message window cannot be closed. To get rid of the unsendable email, I have to quit or force shut down Mail, then reopen Mail and manually delete the email from Drafts.
Has anyone else run into this issue?

As Larry suggested go into iPhoto's Accounts preference pane and make sure your email account information is correct. If you joined iCloud that is a must.
OT

No sound from speaker after upgrading?

Similar Messages

Maybe you are looking for