No Title Sequence on Burned DVD

I just created a movie in imovie and 'shared' it to idvd. I created my title sequence and previewed my movie, tested all my chapter etc. everything was perfect. So I burned. When I previewed my movie in a dvd player and computer it completely skipped over the title sequence and went right into playing the movie. Any ideas how how to fix?

Are you using iTunes purchased music? If so, it is a known problem. See last post on this thread for a workaround.
http://discussions.apple.com/thread.jspa?messageID=5046586&#5046586
Other things to try
Use a good brand DVD-R like Verbatim or Maxcell
Save project as a disk image
Burn disk image to DVD by using Disk Utility
Burn at 2x speed
Hope this helps

Similar Messages

Chapter titles shift when burning DVD

I line up the chapter titles in ine verticle line. The look perfect on the menu page during set up. When I burn the DVD some of the chapter names shift so they don't line up. This seems to happen often.

I've lined up chapter markers vertically, turning off "snap to grid" and turning on the "free position" option and that seems to be stable through the burned DVD.
Patrick, I don't know if this jives with standard etiquette on the forum (I'm relatively new here) but would you please take a look at my question at
http://discussions.apple.com/thread.jspa?threadID=1504460&tstart=0
There have been views but no replies. I think you've answered a similar question in the past but it's archived so I couldn't reply to you there!
Thanks...

I created in iMovie, and extracted audio from one of the clips to use in the title sequence. All is well, export to iDVD and it plays OK, but when I burn the DVD the audio for the titles does not play. Any suggestions?

I created in iMovie, and extracted audio from one of the clips to use in the title sequence. All is well, export to iDVD and it plays OK, but when I burn the DVD the audio for the titles does not play. Any suggestions?

I am on a MacBook Pro with OS 10.6.7 running iMovie '11 and iDVD 7.1.1. Thanks for any input.

Burned dvd shows part of title

When I view my Burned DVD on my tv my Music Video title is cut-off and my subtitles are cut off. How do I get it so they are shown on my tv. Also the clips are in widescreen mode. Can I format them to be in full screen mode?
Thanks

Guys--
It's not a magic button that pushes everthing where it needs to be....
Read Bear's post again--As long as you put everything inside the "safe area guideline box", it shouldn't be cut off when shown on most TVs. Anything outside the box is subject to T.V. overscan.
In addition, when you're creating photo montages, titles and graphics within your projects, etc., make sure you take this into account. Many of heads, bodies, graphics, titles have been cut off because people don't account for TV overscan.
Hope this helps.
T.

Random Single Frame Jump On Burned DVD From Encore??

Problem with a single frame, split second jump on some DVDs output from Encore. The jump is a single frame from a previous part of the timeline. It is hardly noticeable, but annoying. Plus, it doesn't happen with every disc because I retranscoded the same footage using both automatic and manually chosen presets. Sometimes I get a perfectly fine disc. It seems like this problem is random, hit or miss with the transcoding. Has anyone had this? Suggestions? Thanks.

DV 4:3 MXF Video Files From Panasonic P2 Camera To Premiere Pro To Encore Through Dynamic Link
Flowchart = Untitled Project --> Sequence
Basically burning a single sequence, no menus, straight to build, end action - stop, title remote - stop
Tried Automatic Transcoding & Manual
Manual
MPEG-2 DVD
Basic Video Settings
Quality 5
Frame Rate 29.97
Field Order Lower
Pixel Aspect Ratio Standard 4:3
Bitrate Encoding VBR, 2 Pass
Min 5, Target 6, Max 7
GOP - M Frames 3, N Frames 12
Maximum Render Quality

I repeatedly get "error during rendering/encoding of menus/slideshow" message. This process is the same on my iMac, MacBook and another iMac. I have been burning dvd's int he same way for the past 12 months using the exact same steps successfully.

I keep getting "error during rendering/encoding of menus/slideshows" message. I have been burning DVD's in exactly the same way for the past 12 months and mostly on my MacBook which is 3 years old. Obviously I'm using iDVD. I purchased an iMac about a year ago and moved to use this for dvd burning without problem. A few months ago (approximately) I started to experience problems with burning with the error message above. I tried everything including starting the whole process from scratch right down to capturing the movie clips from my video recorder into iMovie, then using them in iDVD. Still the same message came up. I lost count of how many times I repeated the process with different clips and variations and the same thing happened. This was also the case with my MacBook and my husband's iMac.
After taking both of mymac's tothe service centre, having new optical thingys put it and even a new hard drive on my iMac along with a new DVD burner the same thing happened. They told me it must be the process that I am using that is incorrect!
I took my 27" iMac to an apple shop and asked them to assist me while I use the same technique as I always had. The same message came up so they tried using my clips in one of their mac's. The same message. They tried it with different clips and the same message. The only way we could get theirs to work was with a magic DVD which did not produce what I needed and was limited with only one page.
I now cannot use any of my Mac's for the intended purpose that I bought them for - to produce good media for my work! It was suggested that I purchase some non Mac software to burn DVDs which defeats the object of having a mac with iDVD in my opinion. I have a book on iDVD which is very informative and have followed the process to the letter and checked all the trouble shooting and still no remedy. It was mentioned that an up-date may have caused the problem on all my macs.
I feel that this issue should be addressed by Apple as a matter of correctness.
I now find that on the net there are many posts in forums and such like with exactly the same (almost word for word) problems. Please Apple, keep/regain your good name and sort this out.
Jayne Connelly

Thanks Bengt W for your attention to this matter. So much appreciated. And thanks for putting me right on the aim of forums (new to this). Although, you may regret asking for more information. I've added everything I can below.
The process I used is as follows:
Import recorded clips of between 5 and 15minutes each from my video recorder into i
Edit the clips (remove unwanted start and endng)
Add title to front of clips
‘Share’ them to ‘movie’ (export using QuickTime)folder in .mov format individually
Open iDVD and ‘create new project’
Select ‘favourite’ theme that I have set up forall my work dvd’s (this has been used successfully many times and I’ve triedwithout using the favourite them).
Add 2 submenus for each group of clips
Select submenu - drag and drop between 3 – 6 clips in each of the twosubmenus
Change title colours on clips
Dragand drop image into drop zones where required
In‘map’ view I check for any yellow warnings before burning to disc
In an attempt to remedy the problems I’ve tried the following:
Try new DVD discs
Try different themes (favourites and standardones)
Change images in drop zones
Start whole process again even from importingfrom camera again
Two other completely different computers (iMacand MacBook) with iDVD
Go to apple shop and use their computers to doin iDVD
Try with one clip and no menu pages added
Use a clip that I already have that did notoriginate from my camera
Turn computer off and restart
New hard drive
New optical lense (thing)
New DVD burner
Saving to disc image rather than dvd disc
Other points:
I also have a ‘flip’ and ‘iPhone’ whereI’ve imported footage camera which, although limited, records and makes videoclips and burns them to DVD through iDVD without problem.
For example, I have just gone through steps 5 - 11 using some clips that were already imported from my iphone to iPhoto and dragged across. I used a theme that I've used before which has failed and added one sub menu page where the clip went. It burned to disc image successfully.
The startup disc, I believe will have no space issues asit’s a new hard drive with no use apart from this. That could have been an issue before (I didn’t check it) butnot now.
Other technical stuff that I don't understand but you may:
I have…… Mac OS X Version 10.6.7 with all updates onit. Processor 2.8 GHz Intel Corei7. Memory 4GB 1067 MHz DDR3.
iDVD version 7.1.1
HardwareOverview:
Model Name: iMac
Model Identifier: iMac11,1
Processor Name: Intel Core i7
Processor Speed: 2.8 GHz
Number Of Processors: 1
Total Number Of Cores: 4
L2 Cache (per core): 256 KB
L3 Cache: 8 MB
Memory: 4GB
Processor Interconnect Speed: 4.8 GT/s
Boot ROM Version: IM111.0034.B02
SMC Version (system):            1.54f36
OPTIARCDVD RW AD-5680H:
Firmware Revision:     3AHB
Interconnect:    ATAPI
Burn Support:   Yes (AppleShipping Drive)
Cache:    2048KB
Reads DVD:    Yes
CD-Write: -R, -RW
DVD-Write:   -R, -R DL,-RW, +R, +R DL, +RW
Write Strategies: CD-TAO,CD-SAO, CD-Raw, DVD-DAO
Media: Toshow the available burn speeds, insert a disc and choose View > Refresh
If you can solve this you are better than the 'apple geeks' in the shop and the service technicians in the service centre (and of course me but that's no achievement).
Eagerly awaiting your reply.
Jayne

Burning DVD from disc image

I've been burning DVD's from disc images using Encore 1.0 for some time now. ever since I upgraded to 2.0, Encore gives me error messages on my project like:
"first play not set" and
"remote control problem".
I don't see how these messages can appear when I'm using a disc image (i.e. a completed project) as the source. does anyone know?

When you click on the Build DVD button in the Disc panel, Encore does a quick check of errors
in the current project. If you have a new, empty project, you will at least get errors about First Play and Title Remote. Those errors have nothing to do with your disc image, they apply to the current project, from which you are trying to burn your disc image.
These errors may be safely ignored, since they don't have any effect on your disc image.
-Jeff

Can no longer burn DVD's on my MacBook Pro

As the title says, I can no longer burn DVD's. I can burn CD's but not DVD's. I get Sense= code errors and stuff no matter what burner I try out. It doesn't always want to read the DVD's either but ejects them one- two times before it surrenders and starts reading the disc. I've had this Mac for about 1.4 years and I haven't been sitting around every day since, slotting 30 discs in and out of it all day long, i.e the drive hasn't seen that much action to justify this problem.
It can't have anything to do with the media as I've been reading a lot about since the DVD's I try to use have worked perfectly fine before this problem popped up. And I find it hard to believe that my $3200 Mac aint equipped to burn these things and especially not since it was able to earlier. It stopped burning about 2-3 months ago so my guesstimate is that one update or the other from Apple screwed things up but I have no idea how to find out what that might be or more to the point how to solve it.
So, since I strongly disbelieve the media factor ( I have tried different brands and that if it would only be able to burn Verbatim discs then that would be ridiculous ) I wonder if there's any real solution to this. Any firmware to be found for it or some such? I've tried to browse around the Downloads section but can't seem to find anything that addresses this issue. I've also googled quite a bit about it and I've found many others who experience the same problem(s) but never any real solution for it.
Any help would be greatly appreciated.
Thanks.

A lot of folks have found that running a DVD Lens Cleaner disc through can often fix this sort of calibration and sensor problem, it only takes a small spec of dirt or dust to cause errors ...

Video "jigsaw" artifacts appear when camera pans on burned DVDs

I've been pulling my hair out for days as I export endless new sequences at different settings and then burn DVDs, only to find that the problem does not go away. The issue is the infamous "jigsaw" artifact effect, or whatever you want to call it, meaning that when viewing the resulting DVDs, when the camera pans, images "tear" and kind of spazz out. This seems most noticeable when panning past straight vertical objects, but is not limited to only this circumstance. My suspicion is that this is all the result of an interlacing issue in iDVD, but I have certainly learned that I am capable of overlooking the obvious or being wrong. What I don't understand is that with all of us out there working on Avids and using iDVD, either there does not seem to be a unified ideal export setting that resolves this issue, or I am having a comparatively unique problem. The shame is that most of the DVDs are looking great, and it is only this one issue that is sabotaging completion of this project. I'm at my wits end, so any and all knowledgeable help is supremely appreciated. Help me keep my hair.
When viewing any of these exported clips within quicktime player, the jigsaw is not visible. But when viewing the burned DVDs on my Mac, the jigsaw is visible.
When viewing the burned DVDs on my Panasonic HDTV (TH-42PX75U) the jigsaw is visible. When viewing the burned DVDs on my Sony Trinitron Production monitor (non HD), the jigsaw is visible.
Avid Software: Avid Xpress DV 3.5.0
Editing system info: Mac G4 "Mirror door" model - Dual 1.2 Ghz PowerPC - memory 1024 MB
OS Software on Editing System - OS X version 10.2.3
Quicktime version on Editing system: QT version 6.3
Software used to burn DVDs: Idvd 8 version 7.0.1
Computer used to burn DVDs: MacBookPro3,1 - Intel Core 2 Duo 2.2 GHz (codec downloaded from Avid and installed - prior post about video not displayed in QT exports was due to missing codec)
Quicktime version on Computer used to burn DVDs - QT Version 7.4 (92) (with Pro upgrade)
DVD media used: TDK DVD-R 8X 4.7GB
Info on sequence I am burning - A 1 hour and 50 minute program of African wildlife footage all shot on regular mini DV tapes. Camera used was the Panasonic AGDVX100A on the 24 frame setting that does not require a software fix (the correction is done in camera). All the footage was digitized using this camera. When viewing any of these exports afterward within quicktime player, the "jigsaw" is not visible. It only becomes visible after burning them and then watching the dvd. All burns in iDVD 8 are using the "professional" burn mode.
Export settings from Avid and iDVD 8 result summary -
1) Exported at "same as source" from Avid yields arguably the absolute worst result, as I rather suspected with the whole field / interlacing issue, but I was feeling hopeful.
2) Trying to bypass Quicktime by using "dvstream" as the export setting also yields a very poor result. This jigsaw problem does not occur, but the resulting image is terrible. Very milky blacks, the compression is worse, as in much more noticeable, than any other export, and the image is soft and thin looking, rather anemic, and it ruins the visuals completely. What is a bit odd to me however is that I had been using dvstream to burn DVDs of other projects for years on prior versions of iDVD and it never seemed to be a problem. As I tried this one first, without having the Avid codec installed in my MacBook (which I use to burn as I can run iDVD8 on it, also meaning that trying quicktime reference is not an option, I must export, then move the completed export to my macbook pro), I am currently exporting it one more time to see if installation of the codec fixes the horrible compression and color result, but I am not hopeful at all.
3) Tried using an Avid forum suggestion that recommended using 720 X 480 - crop/pad - RGB color levels - even (lower field first) - native dimension 720 x 480. No good.
4) Another Avid forum suggestion to try the "Animation" setting for video
instead of "Avid DV" is not a viable option. The infamous "2 GB limit" message
comes up as the export nears completion and aborts. This message does not appear
with any other export setting. When cutting my sequence in half, the same problem occurs. Even if I could get it to work, the result would be useless if it meant I had to send people several DVDs of the program chopped up into little bits.
5) Heres a summary of other export attempts all using Quicktime movie and "Avid DV" for video, keeping in mind the info I read about how at least one version of iDVD had the field order (ntsc vs pal)reversed a while back. I would expect that Apple has fixed this problem by now, but just in case...
a) odd field - 720 x 486 - 601 - crop/pad - 4:3 Non-square
b) odd field - 720 x 480 - 601 - crop/pad - 4:3 Non-square
c) even field - 720 x 486 - 601 - crop/pad - 4:3 Non-square
d) even field - 720 x 480 - - 601 - crop/pad - 4:3 Non-square
Suggestions to buy a different dvd burning program or new software are nice and all, but I simply cannot afford it. I also have a fear that if I were to try a different program that the same darn thing would happen, as no one seems to be able to say with 100% certainty that this specific problem would be fixed. The only thing that would be worse than my sense of hopelessness and helplessness at present would be spending more money and still not having this maddening issue be resolved.
Help... and thanks to any of you who take the time to read this epic length post and reply!

PROBLEM SOLVED! Thanks to having downloaded Toast 8, the dreaded interlacing has disappeared. The first test made me nervous. I exported from Avid using Sorenson and using the "automatic" settings for Toast's detection of fields etc. The DVD still had the jigsaw at the same spots, but it was not as pronounced as some of the tests with iDVD. I then exported "same as source" and used the advanced settings in Toast to tell it "lower field" and maxed the compression settings as much as I could without exceeding disc space. The DVD result is the best looking I've seen so far and all interlacing artifacts are gone! Thanks to Blackdog at the Avid Forum. I now know this interlacing problem was 100% the fault of iDVD 8 and will be using Toast from now on.

IPhoto won't burn DVDs

iPhoto is refusing to burn DVDs-- it says it can't connect to the drive. But I burned a DVD in finder just fine. What can I do?
I just got my macbook back with a new HD and did a TM restore, although I don't see why that would be related.

It doesn't matter if you empty the Trash or not . A new pref file was created when you opened iPhoto.
Are you still at 10.5.1? If so I suggest you download and apply the Mac OS X 10.5.5 Combo Update followed by a repair of disk permissions with Disk Utility. Then try again.
If you can burn from the other account then your primary account is the culprit. It could be a preference file other that iPhoto's. To determine if that's the case try the following:
Trouble Shooting Preferences in Leopard
1 - Create a folder titled "Preferences A" on the Desktop.
2 - Open the working Preferences folder, HD/Users/your_name/Library/Preferences, and move the contents to the Preferences A folder on the Desktop.
3 - Make a duplicate copy of the Preferences A folder on the Desktop as a precautionary backup.
4 - With the working Preferences folder empty run the application again and determine if the problems is fixed.
NOTE: you may have to drag the contents of the working folder to the trash and empty if moving the contents to the A folder only copies them instead of moving.
5 - If the problem is fixed:
A - open the working Preferences folder (HD/Users/your_name/Library/Preferences).
B - Open the Preferences A folder on the Desktop, select all of the contents and drag them into the working Preferences folder.
C - When the Copy window pops up check the "Apply to All" check box and then click on the Don't Replace button as seen here.
6 - If the problem is NOT fixed, empty the working Preferencess folder and move the contents of the Preferences folder on the desktop back into it.
OT

Burned DVD's have momentary pixelation

Hi
When I export my project from FCPX everything is perfect. When I use IDVD to add theme and chapters there is pixelation for 2 minutes on the burned DVD at the exact same spot of my project every time. Even though the source is 100% it keeps occurring and it's a critical part of the project(wedding). What is going on?

Hi
How did You do the Export from FCP ?
I do
As Quicktime - NO QT-Converstion
And I do as SD-Video Quality - Feeding iDVD HD usually give bad result due to bad down scaling function
Free Space on BOOT hard disk ? How much ?
Is there a special with the material where problems arises ?
- Photos in any other format than .jpg
- Video Sequence - Video-CODEC and frame-rate here ?
- Special funcyion here as "Slow Down, Anti Shake etc) ?
- AUDIO - I only use 16-bit 48 or 44.1kHz .aiff - NO .mp3, .vma etc -
Yours Bengt W

Burned DVDs will no work with PC

My PC reads all other DVDs fine. My burned DVD I made with iDVD plays fine on my MAC and also plays fine in regular DVD players. However, my PC won't even recognize my iDVD-made disc. I also tried it on a friends PC, same thing, won't even recognize it. It's like it's not even there. Does apple just rig everything not to work with PC or what is the deal?

No it's not "rigged". Nor is apple proprietary in this regard. Keep in mind the PC must have a drive capable of reading a DVD-R, and the software necessary to play and decode MPEG2.
Most macs will read and play Dvd's straight out of the box. Not always the case for most PC's. Real Player and Windows Media Player won't necessarily play DVDs unless there is an MPEG2 codec present in the system. I searched this topic over the internet and found what I think is a relatively good answer in spite of the fact the title of the article is misleading since there is no such software as "iDVD HD". At least not to the best of my knowledge (unlike "iMovie HD").
http://answers.yahoo.com/question/index?qid=20080323180836AArptJh
This second link is also informative:
http://discussions.info.apple.com/thread.jspa?threadID=2102239&tstart=270&start= 15
Message was edited by: SDMacuser

Video problems in DVD SP burned DVDs - FCP frame rate issue?

Please help! We have a 99 minute feature project that we shot in 24p (NOT 24pa) on a DVX100, imported the footage into FCP in 29.97fps, and edited in a 24fps sequence timeline. When we exported the sequence through compressor (DVD High Quality 120min 4:3 option) to create the 23.98fps mpeg-2 and burned it to a DVD using DVD Studio Pro (with aiff audio because DVD SP had a problem importing the Dolby file for some reason), the movie image had blurring or ghosting when played on a dvd player and looked very "digital" (not like 24p).
After reading several postings on here, we thought the problem may have been because we were coming from a 24p timeline. Following a suggestion made to another post, we exported the 24fps sequence into a Quicktime movie and then imported that back into FCP and put it in a 29.97fps timeline. It needed rendering and we did that. Then we exported the new 29.97 sequence through Compressor into a 29.97 mpeg-2 and burned with DVD SP. When played on a DVD player, the video looked better this time, but appears to be moving in a sort of slow motion.
Because of the length of the project, we've been using dual layer DVDs, but the break point doesn't seem to be causing any problems. Also, we've slightly decreased the "Average Bit Rate" in Compressor from 5 to 4.5 before creating the mpeg-2, etc. files because the default description of the 120min high quality setting said "90 minutes of video with AIFF on DVD-5" and our movie is 99min. Taking it down to 4.5 changed the default description to "102 or 103 minutes".
Each time we burn, the video and audio seem to be completely in sync... it looks as though the problem is with the speed and I don't know at this point if this is frame rate, bit rate, pulldown, method of burning (i.e. DVD SP rather than something like Toast).
Sorry for the long post but I wanted to try and include all the info I could. If anything is unclear or I left anything out, please ask. Any suggestions would be GREATLY appreciated. Thanks!!
MacPro Mac OS X (10.4.7)

Thank you, thank you, thank you thrillcat and Silal! Getting rid of the render files and then copying the 24 sequence into the new 29.97 sequence worked like a charm. There were some minor things to fix (small gaps between certain cuts, audio and video clips that needed to be lengthened or cut by a couple of frames) but overall very painless... especially when compaired with the prospect of having to re-edit or re-import all our footage (as the guy from Apple tech support suggested).
On the advice of our sound editor, we exported the 29.97 sequence using Quicktime Conversion into a DV Stream choosing DVC Pro in the Options field. We then burned the resulting file onto a regular 4.7GB DVD using DVD Studio Pro. And PRESTO, our movie was back in its wonderful 24p state!
I greatly appreciate everyone's help. Thanks again!
MacPro Mac OS X (10.4.7)

Importing from burned DVDs

Hi,
I'm about to buy a Canopus ADVC300 to import old VHS home movies into FCE, but I'd also like to import footage from some full length burned DVDs so that I can add effects, titling etc. (They're school plays, so no copyright protections, etc.) Can I also use that device to import the DVDs? I'm not sure if it will work since the DVDs are technically already digital, but I'd like to be able to use the Canopus to clean up the inevitably shakiness and bad audio quality. Will this work? Can I just plug my DVD player into the Canopus the way I would a VCR? Is there a better solution that will maintain/clean up the quality?
Thanks!

Yes, you can plug your DVD player into the ADVC-300 just the same as your VCR.
An alternative which will be faster is MPEG Streamclip to directly convert the DVD video to DV or AIC for editing in Final Cut. MPEG Streamclip is free and exellent. However you may need to purchase the QuickTime MPEG2 Playback Component from Apple ($19.99) if you don't already have it installed on your Mac. (The conversion is faster because the ADVC works in real time as you play back the video on the VCR or DVD player; MPEG Streamclip can directly convert the video and audio from the files on the DVD).

Finder thinks a burned DVD is blank

After I've created and burned a DVD with iDVDand then try to play it on my computer is does not play. The computer thinks it's blank and asks what to do. If I select "Open in Finder" it mounts and is titled "Untitled DVD". This may have started after the upgrade to 10.6.3.1.1.
These DVDs will play on other DVD players such my G4, a Dell and my TV DVD player.
Thanks for the help.

After futher checks, it appears as if my DVD drive is half broken. It can burn DVD/CDs. It can read and play commercial DVDs. It can read and play commercial Audio Disks. It can read and play a MP3 disk.
What it can not do is:
Play a burned DVD. It will not startup from a Mac OS 10.5/10.6 Install disk.
To see if the 10.5.3 upgrade caused the problem I tried to install 10.5 on a spare HD. It would read the disk and allow me to start the install, it would read the various install packages and write them to the targeted HD but when it came time to restart and install, it would restart from my main HD and not from the DVD. If I set the startup drive to the DVD it would default to the main drive.
I don't understand this!! It's like being a little bit Pregnant.
Thanks

No Title Sequence on Burned DVD

Similar Messages

Maybe you are looking for