No video signal

Hi all, First time poster and I hope someone can help with a problem. I have a M8020 running Vista pro as a business computer. My problem originally started as an occasional display drivers stopped responding and has recovered message. I updated drivers on my video card and changed my monitor sleep settings but the message never really went away. As time went by the monitor started going to sleep but would come back using the mouse. Then it started going to sleep and I would have to power down the computer and restart using the button on the tower. This started happening more and mor often until now the monitor will no longer wake up. I pulled the video card and reseated it. If I turn the monitor on and off the message says no signal..DUUU! I have also disconnected and reconnected all the cables. I am about to buy a new video card as I assume everything points to that BUT you know what assuming gets you. So I guess I am asking for any ideas you all might have. Thank you in advance!!
Dennis

Hi denp17, I have done some research on the issue that you are having and I have found a updated driver for your video card issues. This updated driver is designed to fix a number of issues and resuming out of sleep mode IS one of them. Please click on the link that I have provided and follow the on-line instuctions. http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=pv-58040-1&cc=us&dlc=en&lc=en&...
If you are still having issues, please write back and I will continue on with more research for you.
Thanks in advance
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Similar Messages

K9N Platinum, 7600GTOC, SLI, No Video Signal

Just built up my new system, specs as follows
MSI K9N Platinum
AMD 5200X2 AM2 CPU
2 Gigs Corsair XMS2 DDR800
2 BFG Tech 7600GT OC's in SLI
Thermaltake TR2-500 Watt PSU +12V(1) 14A +12V(2)15A
1 Maxtor 120 GB SATA 150
1 Maxtor 160 GB SATA 160
When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried? Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal? Any help would be much appreciated.

Hello, welcome to forum.
"When i turned the computer on for the first time, the system boots up and there is one small beep, sounds like it is posting, but I get no video signal from my monitor, which I checked on my other computer and is working fine, I tried both video cards in the 1st slot, in non-sli mode and I get the same result each time, so I get no video signal with all ways tried?"
have you tried with one of them only into 1st PCI-E? use 1st DVI output, when using SLI, ensure SLI bridge is configured property, connect monitor to VGA onto 1st PCI-E slot. also check monitor output is configured property(etc: Input 1, Input 2).
power down PC, remove power cord from the PSU and Clear CMOS Guide
re-test.
ensure all power cables are connected property. try to boot with one memory stick only into slot close to CPU socket.
what D-bracket shows?
"Do I not have enough power in this PSU to run what I have? The video manufacturer suggests a 450W PSU, which I meet, but do I not have enough juice the 12V rails? And would this cause the no signal?"
yes, think is too weak for your system
its recommended to get single rail with high amperes on +12V (over 30A)
read here:
PSU's---2 x 12v---The Dual Rail Myth
Is your problem caused by your PSU?
good suggestion can be found here:
https://forum-en.msi.com/index.php?topic=105635.msg783148#msg783148
https://forum-en.msi.com/index.php?topic=103299.msg757739#msg757739

Solutions for displaying s-video signal on Macbook Pro? (2006 model)

I looking around for ways to display an s-video signal on my Macbook Pro, but i've no idea the best way to this.
I'm not really after capturing or recording the signal, but I just need a means that I can view the signal, and to be able to switch to another program running on the Macbook. (switch back and forth from Mac app to viewing s-video signal)
Ive seen a few products but they look overblown for what I really need to do like the Elgato video capture, and the xlr8 provideo usb devices.
Is there a way that I could use the DVI socket on the Macbook? I have seem its possible to display the Macbook signal on an external display using this socket, but can it be used to take an input signal?
Message was edited by: jauqq
Technical note of what I exactly need this for: I have an old Roland sampler which can be used with an external monitor to aid in its editing. The outputs on the sampler are s-video and digital RGB. So that I dont have to buy an old bulky monitor I want to use my Macbook display for this while I also am running Logic Pro 8 at the same time. And to switch from Logic, to the displayed signal from the sampler.

The DVI out on your MacBookPro cannot be used for input. In order to see the s-video signal on your MBP display you will need an analog-digital converter like the Canopus ADVC-55, plus you will need to run software. You may be able to use iChat A/V, although I haven't tried it for this purpose. It will cost you more than the Elgato eyeTV device, however.
You will find it much easier & cheaper if you just get an inexpensive LCD display to use with your Roland sampler.

No video signal on projector (Lion, MacBook Pro)

Hi guys
since I've update to Lion (10.7.2), I have problems getting a video signal via mini-DVI / VGA to certain projectors. I'm using a Mac Book Pro (end of 2008). I have never encountered similar problem with previous versions of Mac OS X. Restarting the MacBook or the projector doesn't help. Does anybody have an idea what to do?
Thanx
fweth

I also update to Lion from 10.6.8.. My Dell 3300MP projector worked fine with Snow Leopard. Then with Lion, there is occassionally scrambled signal, but most of the time no signal.. Tried restarting projector, restarting computer, turning mirroring off and then on, but no help. I am running an early 2011 13" MBP.. Really frustrating for someone who does lots of presentations and teaching.

How can I get my 2010 mac book pro to send signal out through the mini display port? end signal out through the end video signal out through the

How can I get my 2010 macbook pro to send signal out through the mini display port?

First, what you said is contradictory. You say "can't get a video signal", then say"the Mac wallpaper is broadcast, the mouse pointer is visible". "No video signal" means an absolutely black,blank screen. It sounds like you have plenty of signal.
I am supposing what you are seeing is actually a blank desktop, which is to be expected if your settings are such that you are extending the desktop, instead of mirroring it.
Within the preference panes is a setting that allows you to change this. Open System Preferences, click Displays, and then click Arrangement. You will see that you are extending the desktop. Change that setting.

How do I get a video signal to an external monitor via the mini-display port on my Mac Book Air?

I can't get a video signal out through my mini-display port on my Mac Book Air (version 1). Thus I can't feed BBC iPlayer to an external monitor. There is some connectivity - the MAC wallpaper is broadcast, the mouse pointer is visible and sound is transferred. Is it likely to be a cable connection problem (though the cable works with a Windows operating laptop)?

First, what you said is contradictory. You say "can't get a video signal", then say"the Mac wallpaper is broadcast, the mouse pointer is visible". "No video signal" means an absolutely black,blank screen. It sounds like you have plenty of signal.
I am supposing what you are seeing is actually a blank desktop, which is to be expected if your settings are such that you are extending the desktop, instead of mirroring it.
Within the preference panes is a setting that allows you to change this. Open System Preferences, click Displays, and then click Arrangement. You will see that you are extending the desktop. Change that setting.

Video signaling problem caused by 1.9, 2.0 BIOS (pointing out a BIOS problem)

Hi, i have a problem with the video signal. At random times when i boot up my computer, the computer would power up but there is no signal to the monitor. there is no hdd activity (via the hdd led) and nothing seems to be happening just that the fans are whirring. i have to unplug the computer then plug it again then turn it up again which sometimes repeats the problem. This is very irritating! So i did a little bit of troubleshooting:
1. I changed video cards. I used a SAPPHIRE ati radeon 9600XT fireblade and a LEADTEK GF4 ti4200. Both cards were causing the same problem and when i used both cards to another computer, there is no problem. = NOT A video card problem
2. used differnt kinds of drivers Cat 3.10, 4.10, 4.20 (omega and official) does not seem to do anything (which also i believe the drivers are OS dependent and its the bios of the vid card that starts up the vid card)
3. upgraded from 1.9 to 2.0 BIOS. still the same problem
4. reverted from 2.0 to 1.7 BIOS. the problem ended.
BTW, the board is 865PE-Neo2 - S. on a Intel 2.6Ghz C, 512MB TwinMos ram with m-tec chips, 80gb hdd, enermax 300w psu
so ive' solved the problem, and i just wanted to point out that there is a problem with 1.9, 2.0 BIOS. (havnt tried the 1.8 tho)

Wish I had seen this thread 2 weeks ago, but you did save me from buying a new graphics card. That was the last step (before chucking this mobo completely) in my attempts to fix the same problem. It didn't bother me too much, except I also couldn't get any DVD player (tried 3) to work. Would boot sometimes and at others gave a blue screen video error.
Flashing to bios 1.7 was the only thing that fixed it. Tried different memory, updating software, various combinations of drives, etc. For the record I tried bios 1.8, 1.9, 2.0, and 2.1. Not sure what about those updates causes problems but there definitely is something wrong.
Thanks.

HP w2207 Monitor - "No Video Signal" After Power Outage

My mother has a Mac Mini - 2009 model - that I bought her. It is connected to an HP w2207 monitor I used to have with a mini-display port to DVI [I think, either that or VGA] adaptor. She lives 2 1/2 hours away.
Last week there was a power outage and ever since she cannot get her system to work. Her monitor says "No Video Signal" and then goes to sleep.
I worked with her for over an hour on the phone trying to fix this problem (oh what fun). Tried every combination of things I know to fix it. It seems from her description that the Mac Mini is not actually booting. When I have her turn the computer off by (press the power button, wait, press it again), she reports that she will here the disk drive spin up for 10 seconds but then no more activity. The green light is on, but that is it.
I had her reset the SCM, but that didn't work.
Any help would be greatly appreciated.
Bryan

See if the Mini will boot from the install disk. If it does, have your mom use Disk Utility to repair her internal hard drive. Repeat running repair until Disk Utility gives the disk a clean bill of health. Then repair permissions.
Disk Warrior can sometimes repair things Disk Utility can't. However, it's possible the internal directory is beyond help. In that case, erasing the internal disk and reinstalling the system will be necessary. It's also possible that the disk itself or electronic components in the Mini have been damaged which would require repair at the Mac hospital.
You might want to consider buying your mom a UPC.

Video signal lost on launch of iTunes (after "update")

I just (foolishly) "updated" to the most recent version of itunes. And, surprise surprise, a headache has ensued. I am using a mac mini hooked into a TV via HDMI (the setup is mac mini ---> receiver ---> TV). After the itunes update, Weirdly, when I launch itunes, the video signal gets lost. The application appears to start without any problems at first, but 10-20 seconds after launching, my TV goes black. I've never encountered a problem like this before (I've had my mini hooked to my TV in this setup for some time.) Any thoughts on how to try to address this issue would be greatly appreciated. (If only I had this computer on time machine, I would go back an hour and all my problems would be solved.)

I had the same problem after installing Snow Leopard.
But now it seems magically fixed after updating to 10.6.2

Connection MACBOOK PRO to Philips LCD: NO VIDEO SIGNAL

Hello all,
I recently both a Philips LED TV, type: 40PFL8605H/12.
I have a MACBOOK PRO from 2007.
I would like to use this MACBOOK PRO as a media server on the TV.
I have connected the MACBOOKPRO via DVI-VGA connector to the VGA input of the Philips TV.
Result; I get 'no video signal'-message on the TV screen. I recently connected the MACBOOK to a beamer and it worked perfectly.
Although, the TV say's 'no video signal' the display system preferences does recognizes the TV. It say's PHILIPS FTV and a different number of resolutions.
I have tried them all, the result stays the same.
I'll tried the Philips helpdesk and the answer was that everything seamed to be connected ok...so, no use full help there (yet)
'Google-ing' around did not give an answer either.
Anybody here with use full tips?

Thanks a brody,
I'll get me one of those cables and give it a try...
are you sure it should work then? i see a lot of discussions and people with the same problems...
I was first thinking to buy a new mac mini to use it as my 'home-server' and as multi media player.
However, my 'old' macbookpro is also getting 'ware-out' and is subjet for replacement for profesional purposes...
If I could use my good old macbookpro as media/server, it would save me a couple of euro's...
Can you (or somebody else) advice me... my old macbook as media server and a new one as profesional lap-top or upgrade my old macbook (new harddisk extra memory) and mac mini as home server and media player...
of course, first criteria is to get my old macbook hooked-up to my TV ...
thanks for the advice...
cheers
p

No video signal in

I am using FCP 4.5 HD, I have a G5, tiger, using a DSR-80 going into the AJA lo la using component, I am firewire into the mac. I get video on my NTSC monitor through the aja but no video into FCP, my device control is aja lo la rs-422, capture input aja lo al composite 10 bit. I get nothing in the preview and when I go to capture now. it tells me "no video signal" any ideas what I am doing wrong?

am using FCP 4.5 HD, I have a G5, tiger, using a DSR-80 going into the AJA lo la using component, I am firewire into the mac. I get video on my NTSC monitor through the aja but no video into FCP
So what is it Charisa, Final Cut PRO or EXPRESS?
http://discussions.apple.com/thread.jspa?messageID=7308988&tstart=0#7308988
If you are using PRO then what else do you have plugged into your Firewire bus? AJA's external boxes do not play well with others on the same bus. They have to have one all to their self.
Also, do you have the latest AJA drivers?
K

Monitor no longer recieves video signal [Solved... w/ Fire.]

Greetings and thanks in advance for reading. I'm thinking the problem is either Video or Processor but second opinions are always appreciated:
The problem started about a week ago when I was playing Wizardry 8 via Cedega (OpenGL accelerated Game.) The screen mysteriously went black, the monitor turned to low power mode and the sound looped once or twice before just going dead altogether -- yet the computer was still on. I rebooted and things worked again.
2 days ago the game thing happend while playing Unreal Tournament 2004. Montior went black, sound looped once or twice from the past few seconds, then power stayed on but there was no video signal. I tried rebooting this time only to find nothing happening and it's still doing nothing since. The power turns on, no beeps or anything occur and it goes thru the same familiar clicks when checking the hard drives and CD Rom. (The spinning still occurs as well, the keyboard blinks once and I can turn on / off the numlock. The fans turn on inside the case, and the network adapter is recieving a current.)
I tried taking out the RAM, unplugging the hard drives and such systematicallyh only to have it do the same thing. It boots up, doesn't beep, doesn't proceed and the monitor remains blank. I tried swapping the monitors with no avail. I even cleared the BIOS via popping the battery and waiting a bit (yes it was unplugged) The only thing that produced a notable difference was when I unplugged the video card and powered it up without one. It beeped once long, waited, beeped again long, waited, and kept doing this ad infinitum. I should also mention the red LED indicating that the HD is being accessed is constantly on but there is no HD activity discinerable to the human ear.
My hard ware is a Gigabyte 64 Bit AMD Board (Tryton K8 I believe), GF6 6600 GT, PCIE Model 1 gig of RAM and the rest are minute details but I'll include them upon request.
I've had this machine little under a year now (actually 2 weeks from now it'l be ja year) I haven't swapped out the video or processor since I do not have a spare one to replace it with to test it, neither do any of my friends.
Any further questions or such, let me know. Thanks in advance again.
(Meant PCIE, not EIDE, sorry for the confusion)

Something similar happened to a friend of mine. His laptop (under windows) bsoded twice while playing cube. the second time, it didnt boot up again, and refused to power on, there was no sound from the hard drive, the laptop didnt boot at all.
It turned out he had busted up ram... *shrug* it's hard to say though, such symptoms could highlight a lot of things.
Make sure all the connectors in your case are fine, everything's plugged in, and if you can, test out the ram in another compy
James

Recieve signals from WLAN NIC, decode and produce video signal from VGA or Composite Video out

i am trying to broadcast some MPEG4 video messages over a WLAN and display them on TVs and LCDs. i need to develope an interface between the wireless NIC and the display modoule. this interface has to be able to collect the information, decode the information to reproduce a video signal on a VGA socket or a normal TV composite video socket. does anyone has any ideas how i can achieve this?? please help me!! thank you!

Hi,
Assuming that you are trying to use LabVIEW to achieve this, I believe that it will be simplest if your wireless NIC exposes an ActiveX interface that LabVIEW can use.
Regards,
Ankita

Do I lose High resolution video signal when I capture through FireWire?

I have being reading that capturing through Aja Kona video card is an uncompressed video capture. does it mean, I lose some part of my HD resolution video signal when I capture it through fire wire? Could somebody explain me? Thanks.

No, capturing DV or HDV via firewire is a bit for bit transfer of the original recording ... zero loss.

46SL412U Sudden No Video Signal for all HDMI Ports

My daughters and I were playing the Wii U tonight on our Toshiba 46SL412U LED TV when suddenly the picture when black and the No Video Signal message came up. I changed out the HDMI cable thinking the cable went bad, but still no picture. I power cycled the TV, still nothing. I am also not getting any picture with any of my other devices that are hooked up via HDMI port (BluRay player, Chromecast). Oddly, the REGZA-LINK still recognized that the BluRay and Chromecast are plugged in and switches to the correct input when I power either of them on, but i'm still getting the No Video Signal message.
Is there a setting I've missed that suddenly changed, or did all of my HDMI inputs suddenly go bad? What can I do to fix this issue?

To check the Graphics card's funtionality you may go to BIOS menu and see if is it listed or not; if yes, then it's working, and you may have to check the video/HDMI cables.
Try to boot the PC without connecting any device other than monitor, power cable, mouse and keyboard.
To check the warranty, you may use the below link:
http://www11.itrc.hp.com/service/ewarranty/warrantyInput.do?admit=109447626+1275645640303+28353475
If you have any doubt regarding the warranty, contact HP support.

Input Video Signal to iPad

Hello,
I'm planning develop an App to work on business and it has to receive video signal from a DV connection (Firewire IEEE 1394).
Do you know if is this possible even with an adapter or by developing an external hardware?

It would take more than just an adapter but rather extensive circuitry to convert a Firewire signal into something the iPad could accept though the dock connector. There's a device that can input analog video:
http://www.irecord.com/index.html
but nothing I've seen that will accept video from a Firewire device. Given that an analog converter is possible I could guess that a Firewire converter is at least feasible, but developing one would not be easy.
Regards.

No video signal

Similar Messages

Maybe you are looking for