Not going to sleep when I close the lid

Hi there,
My MacBook Pro is just about 6 months old, I just got it back from an Apple Servicecentre. They exchanged my keybord and total unibody because my enterkey didn't work properly, it was entirely done under guarantee.
But now, when I close my lid, it doesn't go into sleepmode... I used to have no problem with that. Do I have to change something in the settings?
Thanks for the help,
Iris

Do a #1 SMC and #2 PRAM reset, if that doesn't fix it then yes, take it back
Step by Step to fix your Mac

Similar Messages

My mac mac book pro w retina display will not go to sleep when I close the lid or put it to sleep.

My mac mac book pro w retina display will not stay asleep when I close the lid or put it to sleep.
I put the computer in my bag and when I open it again the machine is so hot I can almost not touch it.
I am affraid that the hardware is allready fried.
Also when I press a key to restart after it has been idle for a few minutes it often takes up to a minute to wake back up.
This machine is bran new..
What should I do?

Try a SMC reset:
http://support.apple.com/kb/ht3964
If no success, then use your warranty and bring it in to the nearest Apple repair facility for rectifying this problem.
Ciao.

Why won't my MacBook Pro go to sleep when I close the lid?

All of a sudden, my MacBook Pro has stopped going to sleep when I close the lid. Instead, the indicator light on the front stays on steadily. When I then open the lid, I am asked to log in again, but before I can type anything, the window goes completely black. My only choice at this point has been to hold the power button down long enough to shut the laptop off. Then I wait a minute or so before restarting. Is there a setting I need to check to prevent all of this from happening? I have tried restarting in Safe Mode, then restarting normally, but still the laptop will not go to sleep when I close the lid.

Some process is impeding the sleep function. Since you've tried rebooting and it persists, check and see if Time Machine is hellbent on completing a backup, cause it can have that effect.

My Macbook Air wouldn't go to sleep when I close the lid. I have tried to reset the SMC, but it didn't solve the problem.

Normaly it goes to sleep, when I close the Lid, but suddently this function stopped. That means that Mac'en still is running and become warm, during transport.
(Macbook Air 13 ", medio 2011, 1,7 core i5, 4 MB ram, 256 GB, iMac 22", Timecapsule 1 TB, Airport Express, 2 Iphone 4, 1 iPhone 3s, iPad2)

Test after each of the following steps that you haven’t already tried:
Step 1
 ▹ System Preferences ▹ Print & Scan ▹ Open Print Queue...
Check all printers for unfinished jobs. Deal with any you find.
Step 2
 ▹ System Preferences ▹ Energy Saver ▹ Power Adapter ▹ Wake for network access: uncheck. You may need to unlock the preference pane by clicking the lock icon in the lower left corner and entering your administrator password.
Step 3
 ▹ System Preferences ▹ Energy Saver ▹ Schedule… ▹ Start up or wake: uncheck
Step 4
Disconnect all wired peripherals except keyboard, mouse or trackball, and monitor, if applicable.
Step 5
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select All Processes from the menu in the toolbar of the Activity Monitor window, if not already selected. Enter “powerd” (without the quotes) in the "Filter" text field. Select the powerd process and click the Quit Process button in the toobar (stop-sign icon.) In the sheet that opens, click Force Quit. You’ll be prompted for your administrator password. The process will be relaunched immediately.
Step 6
Boot in safe mode and log in. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Note: If FileVault is enabled under Mac OS X 10.7 or later, or if a firmware password is set, you can’t boot in safe mode.
Safe mode is much slower to boot and run than normal. Don’t launch any applications at first. If sleep still doesn’t work properly, back up all data and reinstall the Mac OS. After that, if you still have the issue, make a “Genius” appointment at an Apple Store to have the machine tested.
If sleep now works as expected, go on to the next step.
Step 7
Still in safe mode, launch the usual set of applications that are running when you have the problem, including your login items, one at a time, testing after each one. Some applications may not work; skip them. You might be able to identify the cause of the problem this way.
Step 8
If sleep is still working after you’ve launched all the usual applications, reboot as usual (not in safe mode) and test again. If sleep still works, you’re done, at least for the moment.
If you still have the sleep issue after booting out of safe mode, post again.

Does not sleep when I close the lid...

Never encountered this before! I have 1 MacBook that works fine, but bought another today that will not sleep when I close the lid. It does sleep when I select it from the menu, but not when I shut it.
Any ideas?

Mine recently started doing the same thing. Now everytime I want to go out with my computer I have to pack up the charger, even if I only end up using it for 15 minutes, because the battery is wasted by 2.5 hours.

Not waking up after sleep when i close the lid of my mac book pro.

Not waking up after sleep when i close the lid of my mac book pro.

Starwin,
Try an SMC reset:
http://support.apple.com/kb/HT3964
Follow the directions that apply to you battery you should not remove yourself, or battery you can remove.
Best

HT3382 I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter. How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter. How do I configure the computer so that it doesn't sleep when I close the lid of the computer.

Hi alangium,
Welcome to the Support Communities!
Resetting your computer's PRAM should restore your Macbook Pro's screen appearance.
OS X Mavericks: Reset your computer’s PRAM
http://support.apple.com/kb/ph14222
This article may provide some information about your Mini DisplayPort to AVI adapter. Have you tried to connect a different VGA monitor to your Macbook to see if you get the same results?
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
http://support.apple.com/kb/HT3382
18. What is the maximum resolution available for use with the Apple Mini DisplayPort to VGA adapter?
The resolution available with the Apple Mini DisplayPort to VGA Adapter is 1920 x 1200. VGA displays that use higher refresh rates (such as 85 Hz) at resolutions of 1600 x 1200 or greater may not generate video properly until you lower the refresh rate.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573#5
How can I detect displays?
If the detect displays option is not available, hold down the Option key while you are in the Display pane.
How do I select additional resolutions on my display?
You can use the Display pane of System Preferences to specify how your display works. Not all options appear for all display models. By default the best resolution for your display will already be selected in System Preferences.
To select a different resolution, use the Scaled option. Some additional resolutions may be available when you hold the Option button.
I hope this information helps ....
- Judy

Won't sleep when I close the lid - HELP!

A while ago, my iBook G4 1GHz was knocked off of a table. The display was smashed and the whole display assembly was destroyed. I bought a new (used) display assembly and installed it. Worked fine, but when I closed the lid, the iBook woudn't sleep. I checked the placement of the magnet in the top case and I reset the PMU. Still no sleep. So I contacted the company that sold me the display and got a different one. Still won't sleep when I close the lid. I checked all of the energy settings, reset the PMU and even tried to force sleep with a magnet from another broken iBook. Still no sleep when I close the lid. It will sleep when I choose sleep from the Apple menu (OS Tiger) and when it sits for a while with the lid open, but not when I close the lid. Any thoughts?

My original problem has not been solved. The iBook still won't go to sleep when I close the lid. I have checked out any possible software causes, and have ruled them out. I have checked to make sure no keys were being pressed when I closed the lid. I took a magnet from another iBook top case and ran it down the side of the display to try to force sleep. No effect. I don't have any Firewire or USB devices attached, to that's not it. Apple, this board, PBFixit.com, and my local Apple-affiliated repair center have no idea why I am having this problem. Two display assemblies have experienced this problem. The original display had been destroyed in a drop. Could some internal damage, like maybe to the logic board, result in such a problem? It's odd that I am the only person out there who has had this problem. Weird, to be sure.

My MacBook laptop won't automatically go to sleep when I close the lid.

I recently got my mid-2009 edition MacBook repaired for a broken screen. Previous to the screen problem, everything worked fine. But ever since I got it back it will not automatically sleep when I close the lid. I don't want to accidentally waste the battery when I'm in a hurry and close my laptop without manually put it to sleep. Is there any way to fix this problem?

The first thing I would try is an SMC reset...
http://support.apple.com/kb/HT3964
....what you describe is listed under the "Power" catagory....

How can I make my macbook pro go to sleep when I close the lid? Currently it doesn't sleep when on battery.

How do I make my macbook pro go to sleep when I close the lid?

For this and other power related issues the best first step to try is resetting the System Management Controller.
Best of luck.

My macbook pro won't go to sleep when I close the lid

I've been having this problem for a couple of years now, and it's getting pretty annoying.
I got this MacBook Pro in April of 2011. Otherwise, it works great. It goes to sleep when I go up to the apple menu and select "sleep." BUT, when I close the lid, it stays on. Heaven forbid I don't have it plugged in, because then the battery will be shot! It also won't go to sleep automatically when I leave it for a long time. Yet another potential battery drain.
How do I fix it so that it goes to sleep automatically when I close the lid and when I leave it alone for a while?
In Energy Saver, I have checked all the boxes necessary: "Put the hard disk(s) to sleep when possible" "Wake for network access" and "Automatically reduce brightness before display goes to sleep."
Am I missing something here, or does my computer just have a defect?

I had the same issue.
I used an external monitor but all of a sudden when I closed the lid my Macbook Pro did not go to sleep!
I solved the problem with a SMC reset.
Try to do it...

Won't go to sleep when I close the lid

When I close the lid of my Macbook Pro (running Lion) it doesn't realy go to sleep. When I open the lid the screen goes black. Does anyone know what the issue is?
Thanks

if you're sayingt he light doesn't blink anymore, that's new to lion.
if you are really having issues that you think are a bug instead of how it should work, try resetting your SMC as this should solve any issues with putting your computer to sleep with the lid.
http://support.apple.com/kb/ht3964
Resetting the System Management Controller (SMC)
Resetting the SMC on Mac portables with a battery you can remove
Note: Learn about removing the battery on MacBook and MacBook Pro.
Shut down the computer.
Disconnect the MagSafe power adapter from the computer, if it's connected.
Remove the battery.
Press and hold the power button for 5 seconds.
Release the power button.
Reconnect the battery and MagSafe power adapter.
Press the power button to turn on the computer.
Resetting the SMC on portables with a battery you should not remove on your ownNote: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.

MB tiger 10.4.11 won't shut down but just go to sleep when I close the lid

Hi,
I'm new to this forum but I'm desperate for your help with my Macbook 10.4.11.
Recently it doesn't shut down properly and each time I shut it down thru the green apple, it just doesn't shut down definitely but after some seconds, the screen turns to black but my mouse's light is still on. When I close the lid, the sleep light is on, too.
I've tried many advices like disabling remote facilities, e.g. Bluetooth, but it won't help. I've updated all softwares and even SMC but that won't help either. Did anyone have the same problem like mine and more important, have you had the answer yet??? I'm fed up with pressing the power off button each time.
For more info, I've installed boot camp and windows but after that, I've uninstalled it and reinstalled brand new Mac OS so there's no way that the problem comes from Windows.
Thanks in advance and waiting desperately for your help...

Hi NOTHING SPECIAL, and a warm welcome to the forums!
How much free space is on the Hard Drive?
Have you done any OS or Disk Maintenance?
At this point I think you should get Applejack...
http://www.versiontracker.com/dyn/moreinfo/macosx/19596
After installing, reboot holding down CMD+s, (+s), then when the DOS like prompt shows, type in...
applejack AUTO
Then let it do all 5 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 5 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
See if it does better then after a restart or two.

Can I keep my MacBook Pro from sleeping when I close the lid?

Is there a way to close the lid on my MacBook Pro without putting it to sleep so that it will continue to play music via USB to my stereo?
I want to use my Macbook Pro to play music on Amarra or iTunes via USB to a DAC connected to my stereo. The MBP will be on a shelf in my stereo cabinet where the lid cannot remain open. I do not wish to connect an external mouse, keyboard or display to the MBP. Is there a way to keep playing the music with the lid closed?
Thanks.

... and there's this:
Apple Portables: How to use your computer in closed clamshell ...

MacBook doesn't sleep when I close the Lid.

Hi Folks,
Im new in this Mac World, finally i got my first Mac. A MacBook 3,1 White with Leopard installed.
I think that there's a problem with it. When I close de lid the Mac doesn't enter in the sleep mode. If it is in the Battery it got in sleep mode after 5-6 minutes, because its the time configured in the System Preferences.
If the power cord is pluged it doesn't got in the sleep mode, never. The monitor shutdowns but the light doesn't blink and when I open the lid I can see that the system doesn't have got in the sleep mode.
Does anyone have this same problem ? Please help!
Thanks in advance,
Fred.

Do you have all the latest firmware updates? Check Software Update.

Not going to sleep when I close the lid

Similar Messages

Maybe you are looking for