Not receiving IP from DHCP

I have (2) networks going into an ap 1200 - the AP has a static ip set on it as 192.168.199.210 which is vlan 20
the other network is from my DSL to have wide open wireless for guests (vlan100) that ip in the router is set at 192.168.199.51 (scope is set not to interfere)
I get the ssid to the client but fails to get an ip address.
I have vlan 1,20,100 trunked on the switch. what am i missing here. thanks

You need to have a router to route between the VLANs, specifically from the Native VLAN (where your DHCP service is probably located) to the VLAN 100 segment.
You'll also need to have some kind of IP HELPER / DHCP forwarding on the VLAN 100 client-side of the router pointing to the DHCP service IP address.
Even though the VLANs are physically located on the same device, they cannot talk to each other without a Layer 3 device to pass the traffic from broadcast domain (VLAN) to broadcast domain (VLAN).
Good Luck
Scott

Similar Messages

Clients not receiving addresses from DHCP

I have a Cisco 2811 router and have configured it to be a DHCP server at a remote site. It seems like it should be pretty straight forward to configure DHCP. Apparently I'm missing something because I can't get clients to receive an address. Below are the applicable parts of the config. I also have tried associating the DHCP pool with the Claims vrf and that did not work either.
ip dhcp excluded-address 10.10.30.0 10.10.30.99
ip dhcp excluded-address 10.10.30.201 10.10.30.255
ip dhcp pool Claims_Office
   network 10.10.30.0 255.255.255.0
   domain-name fmi.com
   default-router 10.10.30.253
   dns-server 10.10.10.191
   lease 7
interface FastEthernet0/0
description Claims Office
vrf forwarding Claims
ip address 10.10.30.253 255.255.255.0
duplex auto
speed auto
no mop enabled
interface FastEthernet0/0/0.1205
description Claims Office
vrf forwarding Claims
encapsulation dot1Q 1205
ip address 192.168.103.2 255.255.255.252

Unfortunately that didn't work. Here is the output before:
Pool Claims_Office :
Utilization mark (high/low)    : 100 / 0
Subnet size (first/next)       : 0 / 0
Total addresses                : 254
Leased addresses               : 0
Pending event                  : none
1 subnet is currently in the pool :
Current index        IP address range                    Leased addresses
10.10.30.1           10.10.30.1       - 10.10.30.254      0
And after:
Pool Claims_Office :
Utilization mark (high/low)    : 100 / 0
Subnet size (first/next)       : 0 / 0
Total addresses                : 254
Leased addresses               : 0
Pending event                  : none
1 subnet is currently in the pool :
Current index        IP address range                    Leased addresses
10.10.30.1           10.10.30.1       - 10.10.30.254      0
What I want is for it to assign addresses from 10.10.30.100-199

Not receiving texts from iPhone contacts when I'm not connected to wifi or cell data. I can't send and receive regular SMS texts with non iMessage users but iMessage users message are not being converted to text when I don't have internet connect

I can send and receive to any non iPhone user. I can send a message as a text to an iPhone user but if I'm not connected to cellular data or wifi I do not receive messages from iPhone contacts. From what I understand these message should automatically send to me as texts instead of iMessages but since the update it's not functioning properly. Please help. I've tried turning iMessage off and I still don't receive the messages until after I reconnect to wifi.

I have the same problem! Before the upgrade, if I wasn't connected to the internet, any messages sent to me from an iphone would convert automatically to a text message. I have payg tarriff, so I turn cell data off, as it costs too much to use it. I have wifi at home and work, but if I'm out and about, I don't receive texts from iphone users until I'm on wifi. I get them ok from non iphone users. There was never any problem until ios7

Can not receive emails from third party email accounts

Recently I started working for a small business which has small business server 2011 and exchange 2010 installed. Before I started there were eight user accounts and they all have unlimited email access. I created a few users through sbs AD and also from
exchange console a week ago. Unfortunately none of them can not receive emails from third party accounts. they all can receive internal emails and also can send mails to any email accounts internally and externally.
This is a night mare for me as new users are having trouble with communicating via mails. I have tried all the methods and now thought of posting this issue on tech net. Please help me on this!!
Thanks a lot!!
Sammy

Checklist for testing inbound email problems, I am assuming outbound emails works ok.
1. Check Port 25 forwarding on all modems routers/firewalls
2. MX Record is created and pointing to the correct Public IP Address, use MXToolbox.com to verify MX Record and test SMTP flow. Also Verify your public IP has not changed, use whatsmyip.org to check you public IP
3. If using POP Connector Service, make sure POP accounts are created properly
4. If using a 3rd party spam host, make sure they forward email to correct public IP address, use step 2 to verify your public IP.

Recently started not receiving texts from one person - AT&T user, also HTC One

I recently started not receiving texts from one person. He also has an HTC One (older model) but has AT&T as his provider. We were texting back and forth last Friday morning (11/8) and then he called me and ever since then I have not received a single text he has sent. He is receiving all of mine and we can receive phone calls back and forth, but his text messages are not coming through. We have both tried restarting our phones and I have also tried deleting him as a contact and recreating it however nothing works. I checked to make sure he was not blocked (which I knew wasn't the case since I could receive phone calls from him as well), and even tried turning the "block contact" on and back off. Any solutions would be greatly appreciated. Right now we are using work arounds with google-talk and facebook messenger but it's very frustrated for me to not receive any of the texts that his phone is saying I am receiving.
It had started sporadically over the past few weeks where I would miss a text from him every once in awhile, but now I am receiving nothing. He is the only one that I am having this issue with as I have texted back and forth with multiple others the past few days with no issues.
Thanks in advance for the help!

Hi! I'm also having the same problem. I have an iphone 5 & one person (who also has an iphone 5 but has AT&T as a provider). We had been able to send & receive phone calls & texts until mid-November. Now, we can both give & receive phone calls from each other and she receives my texts, however, I DON"T receive hers. In fact, if I'm in a group text message with her, I don't receive any of the texts that include her, even though I can give/receive texts individually from the others in the group message. The other two in the group message CAN receive both her texts & mine. This is so strange - I was left out of a whole thread of text messages & none of us knew it. They thought they were including me (nothing bounced back) & I didn't know I wasn't receiving them. Since her texting works with both of the others, I'm concluding the problem must be with my phone. Do I have an incorrect setting? I'm not sure what could have happened. PLEASE help!

Exchange server not receiving emails from gmail

Hi dear.
From 2 days ago our exchange server 2013 not receiving email from gmail account. but we can send from our exchange or outlook to gmail account.
we can receiving email from yahoo, hotmail, aol or other mail server But, just gmail account we can not receive email. plz help us, how can i do.
Thanks

Hi Beigi,
According to your description, I understand that Exchange cannot received the message from Gmail, however others works well.
Great checklist from Hotaka.
Additional, I want to double confirm whether any other antivirus and protection software in your environment, also the
Anti-Spam
or
Transport rule settings, for example sensitive words, IP block list and attachment filter, so that the message from external trigger constraints and be rejected. Meanwhile, please double check in OWA.
Besides, please use message tracking log to get more details for this issue. It’s more helpful to narrow down the problem, for your reference:
http://technet.microsoft.com/en-us/library/bb124375(v=exchg.150).aspx
Best Regards,
Allen Wang

Not receiving email from one domain

Hi,
I am running Exchange 2003 on Windows Server 2003 SP2 and suddenly starting having the problem of not receiving mail from one domain. All other domains seem to be fine, although seem slower to receive mail than normal. The sender of the domain in question does not receive any NDR or bounce back error messages, so they are none the wiser the mail has come through. I have checked the junk/spam, I don't have any filters which could be blocking the domain.
Any ideas??
Thanks

Hi,
Please enable the protocol log on SMTP virtual server to check whether the remote domain has attempted to connect to your exchange server to send email to you.
If the remote domain has attempted to connect to your exchange server, please check whether the message is received by the SMTP server. If the message has been received, please use the message tracking log or queue viewer to check whether the message stuck on the server.
If the message is rejected, you can use protocol log to gather further information.
If the remote domain does not attempt to connect to your exchange server, I think you need to work with the remote domain admin regarding the issue as other domains are able to send email to you with no problem.
Mike

ICloud password but I forget why I sent in the mail verification is not received mail from apple icloud

iCloud password but I forget why I sent in the mail verification is not received mail from apple icloud
<E-mail Edited by Host>

You are not addressing Apple here. We are all just users like yourself. It's not a good idea to post your private email on a public forum.

Warning ALSB Statistics Manager BEA-473007 Aggregator did not receive statistics from ...

Hi,
I am using cluster with osb_server1 and osb_server2. While starting the servers, I am facing below error on Managed Server(osb_server2) but only warning on Managed Server(osb_server1).
Warning on managed server1(osb_server1)
<Warning> <ALSB Statistics Manager> <BEA-473007> <Aggregator did not receive statistics from [osb_server2] for the aggregation performed for tick 1855320.>
Error on managed server2(osb_server2)
<Nov 24, 2011 11:23:00 AM UTC> <Error> <ALSB Statistics Manager> <BEA-473003> <Aggregation Server Not Available. Failed to get remote aggregator
java.rmi.UnknownHostException: Could not discover URL for server 'osb_server1'
at weblogic.protocol.URLManager.findURL(URLManager.java:145)
at com.bea.alsb.platform.weblogic.topology.WlsRemoteServerImpl.getInitialContext(WlsRemoteServerImpl.java:94)
at com.bea.alsb.platform.weblogic.topology.WlsRemoteServerImpl.lookupJNDI(WlsRemoteServerImpl.java:54)
at com.bea.wli.monitoring.statistics.ALSBStatisticsManager.getRemoteAggregator(ALSBStatisticsManager.java:291)
at com.bea.wli.monitoring.statistics.ALSBStatisticsManager.access$000(ALSBStatisticsManager.java:38)
Truncated. see log file for complete stacktrace
Please provide your solutions here.
Thanks

Hi,
I am using cluster with osb_server1 and osb_server2. While starting the servers, I am facing below error on Managed Server(osb_server2) but only warning on Managed Server(osb_server1).
Warning on managed server1(osb_server1)
<Warning> <ALSB Statistics Manager> <BEA-473007> <Aggregator did not receive statistics from [osb_server2] for the aggregation performed for tick 1855320.>
Error on managed server2(osb_server2)
<Nov 24, 2011 11:23:00 AM UTC> <Error> <ALSB Statistics Manager> <BEA-473003> <Aggregation Server Not Available. Failed to get remote aggregator
java.rmi.UnknownHostException: Could not discover URL for server 'osb_server1'
at weblogic.protocol.URLManager.findURL(URLManager.java:145)
at com.bea.alsb.platform.weblogic.topology.WlsRemoteServerImpl.getInitialContext(WlsRemoteServerImpl.java:94)
at com.bea.alsb.platform.weblogic.topology.WlsRemoteServerImpl.lookupJNDI(WlsRemoteServerImpl.java:54)
at com.bea.wli.monitoring.statistics.ALSBStatisticsManager.getRemoteAggregator(ALSBStatisticsManager.java:291)
at com.bea.wli.monitoring.statistics.ALSBStatisticsManager.access$000(ALSBStatisticsManager.java:38)
Truncated. see log file for complete stacktrace
Please provide your solutions here.
Thanks

I am not receiving notifications from my BlackBoard app even though it is turned on in the Notification Center. It works on my iPad but not my iPhone.

I am not receiving notifications from my BlackBoard app even though it is turned on in the Notification Center. It was working fine until a week ago.

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug (very important)
5. Release Home button.
ON COMPUTER
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. Select "Restore iPad"...
Note: Data will be lost

Could not receive classifications from UDDI server. Please change the UDDI.

Hello:
   Im trying to connect from CE in Visual Composer to the
    UDDI url: http://xi.esworkplace.sap.com:50200/uddi/wsdl/uddi_v3_service.wsdl
   but when I try to explore advance search in VC it shows me the following error:
   Could not receive classifications from UDDI server. Please change the UDDI server.
   Any idea?
Thanks
Regards
Mario G

Hi,
The one that Mario is saying is not in NWDS its in CE I guess. I too face the same difficulty. I give the following details that I did in my local CE. After saving the setting I tried to clickd service registry I get some list of errors. Kindly help me and Mario in resolving this. Thanks in advance.
Between Mario the URL of the UDDI and classification is changed now... please note the details that I have set.
==================================
Destination Type: WSDL
Destination Name: UDDI_DESTINATION
URL: http://sr.esworkplace.sap.com/uddi/wsdl/uddi_v3_service.wsdl
System: Java
Authentication : HTTP Authentication
User ID/Password (Basic)
User ID: sruser
Password: eswork123
====================================================
Destination Type: WSDL
Destination Name: CLASSIFICATION_DESTINATION
URL: http://sr.esworkplace.sap.com/ClassificationService/CS?wsdl
System: Java
Authentication: HTTP Authentication
User ID/Password (Basic)
User ID: sruser
Password: eswork123
====================================================
Create new destination Create new backend destination HU2
Destination Type: Services Registry
Destination Name: HU2
System: ABAP
System Name: HU2
Hostname: iwdf1030
Installation Number: 0120003411
Client: 800
Authentication: HTTP Authentication
User ID/Password (Basic)
User ID: <your user in HU2>
Password: <your password>nation CLASSIFCATION_DESTINATION
==============================================
Best Regards,
Suresh

TS4002 Hello, icloud receive messages from gilly hicks, but does not receive messages from another personal account... this is happening me since one week and i dont know how to solve this.... error in the mail delivery system says not valid IPv4 SMTP err

Hello, icloud receive messages from gilly hicks, but does not receive messages from another personal account... this is happening me since one week and i dont know how to solve this.... error in the mail delivery system says not valid IPv4
SMTP error from remote mail server after RCPT TO:<[email protected]>:
host mx6.me.com.akadns.net [17.158.8.114]: 550 5.7.0 Blocked - see https://support.proofpoint.com/dnsbl-lookup.cgi?ip=184.173.9.56:
[email protected]
i do alse receive from gmail....
please help... what is happening!!!!

Just to recap, this is a collection of ports I have collected over time for people who needed this information when setting up the HP ePrint app so that they could view their email from within the app. I am certain other applications also need this information. Although lengthy, I could not find a more comprehensive place to retrieve this information. Feel free to post additional information, faulty information, or other related topics below as this is simply a collection of data and it would be practically impossible to test all of them. Thank you!
Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
When a solution is found please mark the post that solves your issue.
Every problem has a solution!

Not receiving emails from other I pads

Not receiving emails from other iPads

Just other iPads or in general?
Have those other iPads send mail that you can access on a PC and see if their mail is going through.
Can you access other mail or just mail from those iPads?
What is the mail provider involved?
More details can help in finding an answer

I'm not receiving emails from 2 specific domains to my .mac email. Both have the correct address and I don't have any rules set up. Anyone know why this is happening?

I'm not receiving emails from 2 places. I don't have rules set up and both senders have the correct address. The messages aren't in my junk folder either. This is for my.mac account. Anyone know how to fix?

That just sounds like the mail headers. Most people don't know (or care) about them so they're usually hidden.
Check Mail -> Preferences -> Viewing -> Show header detail
I'm guessing it's set to 'All'. Switch it to 'Default' or None as you prefer.

I am not receiving mail from either of my accounts. It keeps telling me the port is timing out. The internet is working however.

I am not receiving mail from either of my accounts. It keeps telling me the port is timing out. The internet is working however.

Was the iPod previous synced to another iTunes library/computer?
Was it setup via wifi?
Setup via iTunes when connected to this coputer/iTunes library?
Have you successfully synced from this iTunes library/computer before?
Do the songs play in iTunes?
Do you have the right boxes checked to sync?
iTunes: Syncing media content to iOS devices and iPod
Try syncing using the manual method
Lat, restore from backup. See:
iOS: How to back up

Not receiving IP from DHCP

Similar Messages

Maybe you are looking for