Officejet 6500A plus - paper wads up from bottom roller when copier is activated

when printer is activated, paper wads up when it begins going from the supply to the printer.

Hi ronpercefull,
It sounds like you are experiencing paper jams. I trust the following document will guide you through the necessary troubleshooting steps to resolve the issue; 'Paper Jam' Message Displays on the All-in-One.
If the issue persists, I suggest calling HP. If you are in Canada or US call 800 474 6836, or you can Contact HP Worldwide.
Even if the printer is out of warranty it is worth calling to see if there is something they can do to help or maybe offer you a discount on a newer model.
I hope this helps.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Similar Messages

HP Officejet 6500A Plus does not feed paper

HP Officejet 6500A Plus, Mac OS X 10.6.8,The printer does not feed paper. Then gives the message that 'printer is out of paper'. I have done all of the reset and cleaning procedures recommended on the HP web site. That does not correct the problem when I do 'Print Status Report'.Observing through the front with a flashlight, the paper feed mechanism comes down on top of the paper stack, but the rollers do not feed paper. Then the feed mechanism lifts up and the error message 'printer is out of paper' is displayed on the small screen on the printer. If a single sheet of paper is inserted deep into the printer so that it can be captured by the print rollers, then the printer produces a normal 'printer status report'.The problem appeared after printing some photos on official HP photo paper with new official HP cartridges. Advice? From:molybdenum

Hello molybdenum, Please follow the steps by clicking the below link.Does not pick paperor Copy paste the below URL in the browser ..http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02446494&cc=us&dlc=en&lc=en&product=4152639&tmp_track_link=ot_search
Regards,
Jabzi
Help the community by marking this post .
Was your question answered? Mark it as an Accepted Solution!
See a great post? Give it a Kudos!
I work for HP

How do i print from my ipad to the officejet 6500a plus?

I read there may be something else required. I want to print directly to the Officejet 6500A Plus. Apple says ths is an Air Print printer capable of doing that. I'm not taking this monster out of the box until I know it will do what I want without a lot of trouble. Thanks.
This question was solved.
View Solution.

Ok, so you were talking about needing the update. It's hard to say as it all depends upon if it came with the new firmware or not. It is not really relevent, however, since it will update itself upon enabling Web Services. This process takes only a few minutes. There is no computer necessary for the firmware update as long as the printer has internet access (i.e. connected directly to a router via either ethernet or wireless). Yes, with an ad hoc connection, you will be able to print from the iPad, but you would have to use its 3G connection as opposed to going through your router. It can only support a single wifi connection also. Go ahead and set up the printer and keep me posted as to what happens.
BTW - What is the issue with your PC that it cannot access the internet?
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided.
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Officejet 6500A Plus - Error Msg says to load paper, but paper is loaded

If this is wrong Board, please advise. This is my first itme posting.
I'm using my Officejet 6500A Plus wirelessly with my Toshiba Windows XP laptop and have enjoyed tremendously. Yesterday I started getting an error message when I tried to print or copy, "Load paper in printer." Paper was loaded. I tried turning it off, and back on. I tried unplugging. I tried removing and replacing the paper many times. I even tried dusting (ha ha). I've probably had the printer less than six months.
Appreciate the help!

Hi Gogilgoes,
Please go through the document below.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02446494&cc=us&dlc=en&lc=en&product=4083977&tmp...
Do let us know if this Document help you.
Thanks
Josh.C
Click on the BLUE KUDOS button on the left to say "Thanks"
Although I am an HP employee, I am speaking for myself and not for HP.

HP Officejet 6500A Plus will not maintain wireless connection reliably

For the HP EXPERTS on Expert Day, April 18, 2012:
B.L.A.T. (Bottom Line At Top): We have an HP Officejet 6500A Plus purchased about 5 months ago. We wanted to use it as a wireless-connected printer in another room besides our home office. It is useless to us because it will not maintain its wireless connection, even sitting just a few feet from the router in the same room. Except for numerous hours of troubleshooting, we have left it sitting powered up, but unused and idle, for almost the entire 5 months in our home office. DURING ALL THAT IDLE TIME, IT HAS LOGGED OVER 3,200 DISCONNECTS, at a consistent rate of 24 disconnects every 24 hours, even though it ALWAYS reports that the wireless signal quality is “EXCELLENT” (all this is according to the Wireless Network Test Reports we’ve printed throughout the last 5 months). So our question is, what is it that this printer is trying to do once an hour over a wireless connection that is causing these thousands of disconnects? And how can we stop it?
NOTE! Before you round up the usual suspects (namely our router and our PC firewalls) please note that we also bought an HP Officejet Pro 8600 Plus ON THE SAME DAY as the Officejet 6500A Plus. The 8600 was also installed with a wireless connection, and has worked without a single network issue for the entire 5 months.
NOW, FOR THE REST OF THE STORY…
WHO WE ARE: My wife and I have worked on HP equipment for 33 years, starting in 1979 as corporate customers of HP when we worked for Exxon; then we both worked for HP directly for 17 years; and we’ve now used dozens of pieces of HP equipment in our home during the last 12 years in retirement. We’re primarily software folks, so we’re not exactly experts in hardware and networking, but on the other hand, this ain’t our first rodeo either.
OUR CONFIGURATION:
PC’s – All running Windows 7 x64 with all important patches applied and Norton Internet Security 2012: HPE-270f and HP AIO 200-Quad, each with full 6500A and 8600A drivers installed on wireless connection. These 2 PC’s themselves can connect either wirelessly or via Ethernet to our home network. The 270f has a dual-band wireless board. Both bands work. We also have a new dv7t laptop with only the full 6500A driver installed via wireless connection. The laptop is now upstairs and it’s connected to our home network wirelessly without any issues. (This is where we had hoped to also put the 6500A, but it needs to work reliably via wireless connection.)
ROUTER: Netgear N600 WNDR3700 providing Ethernet and wireless networking. Router provides a very strong wireless signal throughout the house. No wireless problems with any other equipment including an iPod, two Kindle Fires besides all the HP equipment.
PRINTERS: Besides the two HP printers, the HPE-270f PC has a Canon MP960 installed on it. And if we can’t get the 6500A working right or replaced with something that does work right, we may be buying our second Canon printer. By the way, on the 6500A, ePrint and App’s are set to ON, but of course they’re not being used, just like everything else on this AIO.
OTHER: We also have a Sonos music system that connects to our network via Ethernet and has its own proprietary mesh network (on another frequency) for transmitting ripped music wirelessly to speaker units throughout our house. (If you aren’t familiar with this totally cool system, check out sonos.com). We’ve never seen any evidence of interference between these two wireless networks, or our wireless phone sets either.
HP TOOLS AVAILABLE ON ALL 3 PC’s: HPU
UPDATE 5.003.001.001 (reporting everything up-to-date); HPHDU 3.1.0.17; HPPDU 5.0.0.015 and HPNDU 4.3.0.002.
SYMPTOMS: The 6500A Plus installs quickly and easliy, and connects wirelessly just fine during installation. But sometime over the next hour (usually less), it disconnects and won’t print from PC applications. Sometimes the application puts up an “Unable to communicate with printer” screen, even though the PC usually thinks the printer is “ready”. Other times, the PC thinks the printer is offline (but printers don’t have “offline” buttons anymore!). Often, if you just leave everything alone, the 6500A will somehow reconnect and print out the spooled file 5-30 MINUTES later. So it does usually seem to be able to recover given some time, but that doesn’t always fit our schedule! Occasionally, turning the wireless radio on the printer off and back on will fix it right away. But usually, you have to power the printer completely off, and then back on. As far as we know, that always fixes it…..until the next disconnect a few minutes later!
PREVIOUSLY TRIED: After reading some of HP’s wireless network support websites, I manually assigned a fixed IP address to this printer. It didn’t seem to matter; according to the wireless network test report, it still logs disconnects at the rate of one per hour, and all the failure symptoms were the same.
We also dabbled a bit with setting this printer as “trusted” to the Firewall, but that didn’t seem to matter either.
Next, we connected the printer via Ethernet. The printer immediately started to work, even though it had just been in its “failed” state over the wireless connection. As far as we know, it never failed while connected via Ethernet. This seems to point to a purely wireless hardware/firmware problem on the printer itself.
Late last year, I tried two different chat sessions about this with the inter-continental AIO support teams, each one lasting several hours. Unfortunately, none of their optimistic solution scripts seemed to fit our problem. They both seemed determined to reconfigure the 6500A as a TCP/IP printer, which of course worked fine initially, just like everything else. At this point, they would understandably want to close the chat. But 20-30 minutes later, we could no longer print to it. During the second chat, they got into one of our PC’s remotely and effectively turned off the spooler (by selecting “Print Directly” or something like that). After that, all was well again (as usual) UNTIL the printer disconnected, at which time attempting to print from that PC would HANG the application (since the spooler was no longer buffering) and eventually hang the whole PC. One giant leap backwards. That’s when I gave up on the multi-hour chat sessions.
The three diagnostic utilities (HDU, PDU, NDU) have been tried over and over. When the printer is in its disconnected state, the DU’s usually don’t detect the 6500A at all, or if they do detect it, they are unable to fix anything. Frankly, it’s easier to just power the printer off (which takes about a minute) and power the printer back on (which takes more than a minute) and then wait for the spooler to kick in (usually about 30 seconds). BUT WE DON’T CONSIDER THAT A SOLUTION!!
B.L.A.B. (Bottom Line At Bottom): We have used up nearly the entire black ink cartridge and at least a ream of paper troubleshooting this brand new printer, to no avail. This printer is useless to us unless it can maintain a wireless connection reliably. Please help!
Thanks –
Bob and Jane
(Note: we have an appointment from about 11:20 am EDT – 1 pm EDT, 8:20 am PDT till about 10 am PDT)

I bought the Officejet 6500A Plus about one month and have experienced the very same problem. I tried to remedy this problem following suggestions in a number of different posts (static IP, router, firewalls etc), all to no avail. Last week I called support. The support I received by the tech over several hours and different days for a week was very good. However none of his suggestions corrected the connection issue. After today's recommended fix failed, he advised HP is aware of this issue with the 6500 and other affected printers. He claimed HP was working on a firmware upgrade. He did not know when the update would be provided. The tech also claimed HP acknowledged this problem in a written announcement. He agreed to email the announcement to me. I haven't received it. This has been the only problem I've had with the 6500

HP Officejet 6500A Plus fax report

How do I stop my HP Officejet 6500A Plus from printing the fax report? I can't seem to find this setting anywhere and I'm tired of wasting ink & paper.
Printer: HP Officejet 6500A Plus
Operating System: Windows 7 Home Premium with Service Pack 1

HI,
Press setup and find the fax setup menu. In there there should be an option Fax Report. In there you are able to tell the report when or when not to print.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Although I work for HP my posts and replies are my own
Please mark the post that solves your problem as "Accepted Solution"

I cannot get my HP Officejet 6500A Plus 710N to print in color. I have reinstalled the drivers..

I cannot get my HP Officejet 6500A Plus 710N to print in color. I have reinstalled the drivers. It used to print in color and just stopped. I think it may be a settings issue? I have checked the ink levels and they are all fine. When I print a diagnostic report on print qualify, the black prints well, but there is no color printing.

Okay, I had the same problem. It's most likely your printhead. All you have to due is clean it.
Note: I was sceptical of this approach but can fully attest to it's sound results as it restored my printer back to full functionality. Prior to this the printer only would print Black ink.
The print head is the carriage that holds all of your ink cartridges in the printer. On the 6500A it's super easy to remove. Opent your lid like your changing your ink cartridges. Remove all of your ink cartridges. Once they're out. There is a lever on the left side of the carrier that holdes your ink cartridges. Lift it up and the print head comes right out. Net take your print head to the sink and run it under hot water aiming towards the the four cirles were the ink flows into. Keep running it under the hot water until it is coming out clear. It's okay to run it under the bottom part too infact you'll need to inorder to get it completely rinsed out. Also don't touch the computer metal strips with your hand thought you can run water over them. Once your done rinsing use a blow dryer or a can of compressed air (thats what I did) to dry every thing out. I was able to get everything dry in about 5 minutes or so. Let it sit for a few minutes and check it again for water. I recommend moving it around to get full exposure to insure it is dry. Also if you use a hair dryer try to put it on a cold setting since there ar rubber grommets the surrount the inlet ink ports you wouldn't want to melt them with the hot air etc.. Like I said I used a can of compressed air. It's important to use a quick method of drying as mentioned otherwise mineral particles could become deposited on the unit. This won't happen with the methods as I've described because the molecules won't be able to bond since your blowint them off. Oh yeah, you'll want to place a clean peice of paper down as your blowing because at first you'll end up with a few black jet marks as your blowing. Also don't wear your favorite white shirt lol.
Okay once it's dry replace the print head carriage back in push the lever down install the ink cartridges. Close the lid then unplug the printer. Wait 5 seconds plug it back in then it will reboot and start its set up procedure kind of like whet you first bought the printer except you won't have to change any of your network or setup setting since they are saved in memory. Also be patient about the set up procedure it seemed very slow for me. Once it finishes you will be prompted to run the printer alignment process. Run the alignment process and you should be all good. If not at least you gave it a shot. If this doesn't work your going to have to pay $60 for a new printer head. Which is not that big of a deal but hey if you can fix it for free why not. If you do decide to buy a new printer head you might find deals online or ebay just make sure it's an Genuine HP print head. And lol use the Genuine HP ink cartridges. Finally make sure you print at least on colored page per month to make sure the ink doesn't clog up in the future.
Remember this suggestion is after you have run the HP clean ink cartridge procedure twice. Sometimes the clean procedure will correct the problem first. Also there is video I watched on YouTube about this just search for "Clean HP 6500 print head. Hope that helps
Once it's all dry just reinstall the printer head carriage

OfficeJet 6500A Plus Goes Offline and Won't Come Back

I'm having trouble with my OfficeJet 6500A Plus, keeping it "online" to the wireless network in my home. I am trying to print from my HP Pavilion laptop which has been loaded with the latest software from the HP Support site.
The printer shows itself to be online to my router. I've even run the Wireless Setup Wizard over again to reintroduce the printer to the router. But, no, my laptop considers the printer to be "offline" and, if I try to remove and reinstall the printer, Windows can't find the printer on the network.
By the way, my Pavilion laptop is new, purchased in July and it's running on Windows 8.1.
Any help will be greatly appreciated.
Thanks,
Denny LaBarge

Hello there Denny, aka @labargephoto
I understand your printer is not being found when you try do install it on your network. Check out the steps in the guide below and follow them thoroughly and they should help the installation problem.
'Unable to Find the Printer' Message Displays on the Computer During a Network Installation
Have a great day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

My HP OfficeJet 6500A Plus printer/scanner/fax/copier won't connect to my wireless network

I tried going through the Wireless Network setup on my HP OfficeJet 6500A Plus machine. The printer recognizes the network and I then type in my network's password but it won't connect to the network. What can I do? I would like to be able to print and scan wirelessly. Help please!

Hello erking,
Sorry to hear that you are having an issue with connecting the printer to your Mac over a wireless connection.
I have done some research and I have found a great document that deals with The Printer Is Not Found During a Wireless Network Installation.
Please feel free to write me back and I will be happy to assist you further with any questions or concerns you may have.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HP Officejet 6500A Plus not staying connected to wireless network

Just picked up a HP Officejet 6500A Plus e-All-in-One Printer - E710n the other week and set it all up and it was working wonderfully. But I noticed after it goes into sleep mode it disconnects from the wireless network and doesn't reconnect.
I will get a overview of how I have it all set up.
I have a DSL modem with a TRENDnet TEW-639GR router connected to it. I have set my router to reserve IP addresses for the computer and printer. That way I can leave the computer and printer wireless IP settings as automatic and they will always get the same IP address. I do this for the wireless network at my parents place as well and it works perfectly with their HP Photosmart C7280.
I also set up the HP ePrintCenter feature on the printer so that I can print by sending the printer an email. When I first set it all up this was working great. I tested it all and it was awesome. When I would log onto the ePrint website it would show as connected and it was all good.
So then what happened was it was all fine then the next day when we want to print something the computer says the printer is offline. I go on the HP ePrintCenter website and it says not connected. I print out a wireless network report page and it says not connected. After I printed that test page, I guess it woke up the printer enough or something as it then connected to the router and printed fine as well as showed up as connected on the ePrintCenter website. So all was good. Then the next day the printer goes to sleep and again it shows as disconnected.
Should it not be staying connected in sleep mode? How will the printer know something is being sent to it and that it should wake up if it is not staying connected?
Any suggestions of what I should change with the settings? I suppose I could try setting the IP settings as static on the printer itself but I shouldn't need to as I set it to static on the router. When it finally does reconnect it does always keep the same IP. If that is what is required I guess I could do that but then what is the point in having an automatic setting if it doesn't work? I would rather have this issue fixed that have to do a work around for it.
Thanks in advance!

Hi,
The printer should stay connected to your wireless network after the printer enters the sleep mode.
This is not an expected behavior.
I believe such an issue may be caused due to a signal quality or any conflict as too many broadcust on the same channel.
Please try the following steps in order to better understand the issue:
Follow the Wireless Setup Wizard if your printer currently disconnected
Enter the Setup menu.
Enter the Network menu.
Click Wireless.
Click Wireless Test Report.
What is the signal quality provided by the report and what channel used to broadcast by your router?
If you may scan and attach the report, it may help to better understand any possible cause.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP Officejet 6500A Plus

My HP Officejet 6500A Plus all in one printer recently stopped functioning and printing. First the Wireless network stopped working (Wireless Status Disconnected) and the Wireless Netwok Test Report advice was “contact HP support”. Then I started getting endless errors and flashing print screens with numerical references like 83C00009, 00729C98 etc. Any attempt to turn off the printer using the “off button” resulted in another error message. The following are examples of the stream of new error messages that appeared each time the “off button” was pressed: B0000A16; B03DA14A; B811DEB6; B8383184; B03E3B66; B83D99B8 etc. To finally “turn off” the printer it became necessary to disconnect the power. I have consulted the manual and queries on the HP site using the numerical references as search criteria, does not return any useful results / strategies. I found a video about how to do a partial “reset” (turn on using # + 3) but while this did allow me to access the print screen, it did not resolve anything and the numerical errors and flashing lights reappeared. I downloaded the HP diagnostic tools, but they came up with nothing – i.e. could not communicate with my printer. I read on some post that there may be a problem with the printer head, so I ran the Printer Status Report, but it seemed OK. Regardless I ran the clean the PrinterHead tool, and again this seemed OK, so I didn’t run the 2nd stage. My printer is out of warranty. It is 1.5 years old, but hasn’t been used that much. According to the Printer Status Report it has printed 1534 pages and scanned 290.
What can I do? Most of the "internet searches" suggest that if the printer is out of warranty the only option is landfill.

Thank you. Thesole reason I bought this printer was to use its wireless “Airprint” functionality to print from an iPad and when it worked it was a fabulous product. The start of these constant alphanumeric errors seemed to coincide with the wireless function ceasing to work (it went offline, HP Network Configuration Report – Network Status “Offline”, and Wireless status “Disconnected”). Maybe that was just a coincidence. Running the “Wireless Network Test Report” the recommendation is “Contact HP support***”. I.e. The Wireless is on (blue light good) PASS, but the Wireless Working status is FAIL.
I have only tried using the USB in an attempt to get around the wireless not working, i.e. still able to do some basic printing and perhaps upload firmware updates etc. I have tried different USB ports on my laptop computer but only with the same USB cable that came with the printer. This original printer cable has only been used a couple of times and it has on two occasions allowed me to print successfully from the laptop (i.e. initially it worked although . Surely it should be OK. I am reluctant to go out and buy another cable in the hope that it might resolve something and I don’t really have access to another computer to test.
Thank you I have previously seen that article. It was somewhat useful. My errors messages (mostly 83C0009, and sometimes just a black and white striped screen or B0525DAE, B866A570 etc) however do not include system ink failure and the article basically therefore simply recommends switching the computer off at the same time the ink cartridges are removed. This has in the past provided some improvement in the frequency of the error messages but it is usually short-lived and the error message returns. The error message can however become entrenched and at that point the print cartridges don’t move when the printer door is open and therefore can’t be removed. At this point I've tried turning the printer on while holding down #+3 to try and get back to a home screen, rather than an error screen.
On the upside, I can occasionally still make photocopies and the print quality is good.
Any guidance on what I should do next?

Wireless configuration for HP OfficeJet 6500A plus All-In-One printer on Ubuntu 10.04

I have bought a HP OfficeJet 6500A plus All-In-One printer CN557A, which I want to use with ubuntu 10.04 64-bit as a wireless network printer.
Before i bought i checked compatibility on www.hplipopensource.org and www.openprinting.org, and all was in order.
The machine is autodetected and fully functional when connected with a usb cable, but i have not managed to get it to work as a wireless printer.
This is what I did:
I configured the printer on the wireless network (through the printer interface), and it connects. It prints out a "Wireless Network Test Report", and everything works. I can ping to its local ip adress, and access it through the browser. HP eprint also works.
I installed hplip 3.11.10 and dependencies manually. I did this because the default hplip in ubuntu 10.04 did not recognise the device.
I ran 'hp-check', which gave no errors or warnings:
tjoff@mek-403-jakbo-01:~$ hp-check
HP Linux Imaging and Printing System (ver. 3.11.10)
Dependency/Version Check Utility ver. 14.3
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball
has the proper dependencies installed to successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode
will check both of the above cases (both compile- and run-time dependencies).
Saving output in log file: hp-check.log
Initializing. Please wait...
| SYSTEM INFO |
Basic system information:
Linux mek-403-jakbo-01 2.6.32-35-generic #78-Ubuntu SMP Tue Oct 11 16:11:24 UTC 2011 x86_64 GNU/Linux
Distribution:
ubuntu 10.04
Checking Python version...
OK, version 2.6.5 installed
Checking PyQt 4.x version...
OK, version 4.7.2 installed.
Checking for CUPS...
Status: scheduler is running
Version: 1.4.3
error_log is set to level: warn
Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0
| COMPILE AND RUNTIME DEPENDENCIES |
note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).
Checking for dependency: CUPS - Common Unix Printing System...
OK, found.
Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.
Checking for dependency: CUPS image - CUPS image development files...
OK, found.
Checking for dependency: DBus - Message bus system...
OK, found.
Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.
Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.
Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.
Checking for dependency: libjpeg - JPEG library...
OK, found.
Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
OK, found.
Checking for dependency: libpthread - POSIX threads library...
OK, found.
Checking for dependency: libtool - Library building support services...
OK, found.
Checking for dependency: libusb - USB library...
OK, found.
Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.
Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.
Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.
Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.
Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.
Checking for dependency: Python devel - Python development files...
OK, found.
Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.
Checking for dependency: Python XML libraries...
OK, found.
Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.
Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.
Checking for dependency: Reportlab - PDF library for Python...
OK, found.
Checking for dependency: SANE - Scanning library...
OK, found.
Checking for dependency: SANE - Scanning library development files...
OK, found.
Checking for dependency: scanimage - Shell scanning program...
OK, found.
Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.
| HPLIP INSTALLATION |
Currently installed HPLIP version...
HPLIP 3.11.10 currently installed in '/usr/share/hplip'.
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.11.10
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.11.10
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=no
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.11.10
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=no
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no
Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.
[plugin]
installed=0
eula=0
Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW"
[commands]
scan = /usr/bin/xsane -V %SANE_URI%
[installation]
version = 3.11.10
date_time = 2011-11-16 14:30:35
[settings]
systray_messages = 0
systray_visible = 0
[fax]
email_address =
voice_phone =
[refresh]
rate = 30
enable = false
type = 1
[polling]
enable = false
device_list =
interval = 5
| DISCOVERED USB DEVICES |
Device URI Model
hp:/usb/Officejet_6500_E710n-z?s HP Officejet 6500 E710n-z
erial=CN16F2402Q05JW
| INSTALLED CUPS PRINTER QUEUES |
B-403-271-A4-COLOR2
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-Color
B403-271-A4-BW
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-BW
HP-Officejet-6500-E710n-z-FAX
Type: Printer
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
PPD: /etc/cups/ppd/HP-Officejet-6500-E710n-z-FAX.ppd
PPD Description: HP Officejet 6500 e710n-z, hpcups 3.11.10
Printer status: printer HP-Officejet-6500-E710n-z-FAX is idle. enabled since 2011-11-16T01:00:45 CET
Communication status: Good
| SANE CONFIGURATION |
'hpaio' in '/etc/sane.d/dll.conf'...
OK, found. SANE backend 'hpaio' is properly set up.
Checking output of 'scanimage -L'...
device `hpaio:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW' is a Hewlett-Packard Officejet_6500_E710n-z all-in-one
| PYTHON EXTENSIONS |
Checking 'cupsext' CUPS extension...
OK, found.
Checking 'pcardext' Photocard extension...
OK, found.
Checking 'hpmudext' I/O extension...
OK, found.
Checking 'scanext' SANE scanning extension...
OK, found.
| USB I/O SETUP |
Checking for permissions of USB attached printers...
HP Device 0x5412 at 002:005:
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
Device node: /dev/bus/usb/002/005
Mode: 0664
| USER GROUPS |
lp adm dialout cdrom plugdev lpadmin admin sambashare vboxusers
| SUMMARY |
No errors or warnings.
Done.
I then ran 'sudo hp-setup', chose the device (which was detected), chose my wireless network, entered the wireless security key. On the configuration results dialog I get two messages:
"Your printer has been succesfully configured on the wireless network. You may now unplug the USB cable"
and
"The Ethernet cable is plugged in which will prevent you from connecting to a wireless network. To connect wirelessly, remove the cable and try again. (VSA000)"
There is no ethernet cable plugged in, so i can't remove it. I unplug the USB cable and click 'finish'. This makes the 'hp-setup'-dialog start over again, and the printer has not been installed.
In the terminal i have the following:
tjoff@mek-403-jakbo-01:~$ sudo hp-setup
[sudo] password for tjoff:
HP Linux Imaging and Printing System (ver. 3.11.10)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Searching on USB bus...
GET /IoMgmt/Adapters HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Profiles/Active HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Protocols HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
error: Missing response key: 'iorotocols-iorotocol-dd:dnsserveripaddress-0'
GET /IoMgmt/Adapters/Wifi0/VsaCodes.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks/SSID=mVnmXfsu HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/IoConfig.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
I then tried to reconnect the printer usb cable and run 'hp-toolbox' and click "Wireless/wifi setup using USB". Now i get the error:
tjoff@mek-403-jakbo-01:~$ hp-toolbox
HP Linux Imaging and Printing System (ver. 3.11.10)
HP Device Manager ver. 15.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
HP Linux Imaging and Printing System (ver. 3.11.10)
Wifi Configuration Utility ver. 1.1
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
error: Channel write error
error: An I/O error occurred. Please check the USB connection to your printer and try again. (Device I/O error)
Done.
I do not how get past this stage, and any help is welcome.
This question was solved.
View Solution.

A friendly soul on ubuntuforums pointed out to me, that the wireless configuration is only necessary when the printer is NOT connected to a (W)LAN. So all I really had to do was to configure the printer in the CUPS administation page, and it worked. Problem solved. Silly me.

Apple Airprint to HP Officejet 6500A Plus via Wired Connection to Router

Hi There,
So I've done a considerable amount of research into this across the internet and this forum and I'm still struggling to find a satisfactory solution.
I have an HP Officejet 6500A Plus connected by ethernet into my BT Homehub 3.
It is my understanding that even though this is a wired connection, as long as my iOS device (iPad 2 or iPhone 5) is connected to the same router, I should still be able to see this Officejet over through the airprint facility.
Unfortunately this is not the case. I only get the "No Airprint Printers Found" message on both devices. The only way I have managed to get my Mac Pro (Mavericks) to connect was to mannualy add using the IP address for the printer.
Can anyone give any guidance as to what I might be doing wrong? The printer is definitely connecting to the internet as I can print from my iOS devices using HP ePrint app for iOS.
Some might say well what is the problem, just use the HP app but this is not point. I believe if something has been implemented to make things easier then use it. I chose this printer specifically for this functionality so it's a little frustrating to find it so difficult to achieve the desired results.
Hope it's something straightforward and someone can help.
Thanks,
Steve
This question was solved.
View Solution.

Further to this request, and reading many more similar issues, I think I may resolved this.
I am not 100% sure but I have read some threads suggesting there are issues around BT's Homehub 3 and bonjour so this may be an issue.
I have tried the following over the past couple of days...
1) Completely reset my router (wiped all settings and started again) - No luck!
2) Tried changing from WPA2 to just WPA security - No luck!
3) Tried forwarding the bonjour ports to the printer - No luck!
4) Switched off router, printer and all iOS devices then powered back router, printer and then iOS devices - Printer appears on iOS devices but when print was selected, iOS device repeatedly returned Printer Not Connected error.
Finally, what seems to have done it (at least for now) was...
1) Unplugged ethernet from the Officejet and set it up as Wireless connection.
2) Powered down router, printer and all iOS devices then powered back up in the order stated earlier.
3) So far I have tried printing an email and a web page from my iOS devices and both have been sucessful.
Incidentally I had been struggling also to airplay from my iPhone and iPad until I started messing around with settings above and now this issue also seems to be resolved.
Due to variety of combinations (different printers, routers etc) people will have, it seems to be quite difficult to find a solution which addresses an individual problem however I hope some of my experimenting and findings might help others in some way.

Problems printing to HP officejet 6500A plus e-All-in-one printer e710n

Hi,
I am struggling to print to my " HP officejet 6500A plus e-All-in-one printer e710n". According to the setup network test (Wireless network test report), everything is successful (status "PASS" for all fields). I also checked that the IP configured is the same as the IP displayed on the printer when i push the wireless button (updated via "Update IP address").
I have a laptops as well as netbooks connected to the wireless network. All these devices could previously print, however now none of them can. When i run the diagnostics (both the standard trouble shooter, as well as the one from microsoft when clicking on the fixit option), no problems are detected. When checking the device manager, i can see no conflicts.
When i open the printer control panel and click on "Customize your printer" and then go to "Ports" and click on the "configure port" option, i get an error "An error occurred during port configuration. Operation could not be completed (error 0x0000007b).".
Please assist with any suggestions.

I was able to resolve the problem.
I reinstalled the printer on one of my other laptops (this might have cleared up an error on the printer). I think the true problem is related to the fact that we left the printer on, we've started switching it off when not in use. Even though it goes into sleep mode, it seems to cause problems over time if not switched off on the printer itself.
The basics i did was check the network connection, printed a status of the network connectivity (you can do that from your control panel on the printer). If the network looks good, then try leaving your printer off for an hour or so, if that doesn't work, try reinstalling the printer on your device and start switching it off after use. I know it sounds crazy, but that's what i've been doing and haven't had a problem since.
It was a strange problem, in some cases i wasn't able to see the printer from devices that previously could, when the devices that could see the printer tried to print, it would print okay for a few pages and then start printing garbage, followed by failing completely and cancelling the print. When this happened there would be an error on the device saying it cannot connect to the printer, even though it could at the start of print.

HP update HP Officejet 6500A Plus e-All-in-One Printer-E710n multi fails @ 96%Z

HP Officejet 6500A Plus e-All-in-One Printer - E710n
Windows Vista
HP is trying to update my HP Officejet 6500A Plus e-All-in-One Printer - E710n w/ "HPZSetup.exe & multi fails @ 96%
Errors:
HP-PhotoSmart All-In-One Series "Error" "wStub" "2229580"
Same message appeared multiple times with new numbers: 459624; 525134; 328216
I am on WIFI but system always shows me on USB. I thought maybe that was the problem so I connected by USB. No Help.
I assume this is an update?? HP is insistant and keeps sending me this update which alwaysends in FATAL ERROR at 96%
Next steps?? Thanks JLM_JR
This question was solved.
View Solution.

No Problem. Is everything working now or this tool only removed the HP software? If so, then try downloading the full feature software to see if this fails or not here. Please choose your correct operating system; Either 32 bit or 64 bit. I will be looking forward to hearing from you.
I worked on behalf of HP.

Officejet 6500A plus - paper wads up from bottom roller when copier is activated

Similar Messages

Maybe you are looking for