On startup Mac Pro I get a blue screen and a cursor on the upper left. The mouse cursor shows up independently. Is it likely a video card failure?

On startup Mac Pro I get a blue screen and a cursor on the upper left. The mouse cursor shows up independently. Is it likely a video card failure?

I managed to boot the computer and get the desktop to show. I now have a "repaired" computer. There are several problems that have cropped up. One is that I can only start up now in Safe Boot mode. Is there a way to turn it off? Also, I do not have a sound list, so I can't access anything requiring audio. Google Chrome only shows up as a white screen. Pictures that loaded before don't load in browsers, etc. Any suggestions? I figure I should reinstall Mac OS Lion for starts, maybe even do a mirror backup and reformat the drive. I think this drive has turned into scrambled eggs...what a headache!

Similar Messages

  • HT4848 Hi my name is Hajk and i got a friend that has a problem with her macbook, she gets a blue screen and cant log on. So i told her if she had an reinstall disk so that i could reinstall for her but she didn't get one with the macbook. what can she do

    Hi my name is Hajk and i got a friend that has a problem with her macbook, she gets a blue screen and cant log on. So i told her if she had an reinstall disk so that i could reinstall for her but she didn't get one with the macbook. what can she do ?

    If this is a fairly new Mac running either v10.7 Lion or v10.8 Mountain Lion she can use Lion or Mountain Recovery to repair the startup disk or reinstall OS X.

  • On start up sometimes I get a blue screen and start up hang there

    On start up I sometimes get a blue screen and it hangs there the only way to get out of this is to turn the iMac off at the back then when you turn it back on the desk top appears without going through the startup screens. Even had the blue screen when starting in safe mode.

    Then run Apple Hardware Test in Extended Mode, it's possible you have a hardware issue. If you still can't locate the issue the next step is taking the machine in for a professional diagnosis at your local Apple Store or AASP.

  • My Mac can't get passed gray screen, and I cannot boot from cd. Help!

    My Mac can't get passed gray screen, and I cannot boot from cd. Help!

    Grey Screen
    https://support.apple.com/kb/TS2570
    https://discussions.apple.com/message/16276201#16276201

  • My 13" macbook just stopped working. When you turn it on you get a white screen and hear a repetitive clicking sound on the left side. Is this the hard drive? Any suggestions on replacement drives?

    My 13" macbook just stopped working. When you turn it on you get a white screen and hear a repetitive clicking sound on the left side. Is this the hard drive? Any suggestions on replacement drives?
    Thanks

    Put your install DVD into the optical drive (CD/DVD drive) and reboot. Be sure to either use the disc that came with your Mac, or, if you installed a later Mac OS X version from disc, use the newer disc. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option Key until the Install Disk shows up) until the apple shows up. That will force your MacBook to boot from the install DVD in the optical drive.
    When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
    If it is, then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions. After repairing use Startup Disk from the same menu to choose your hard drive for restarting from your hard drive.
    If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

  • When I first open Firefox it is fine but if I open a second tab to search another site I get a white screen and have to continually click 'back', click the site link, white screen, back, click the link, white screen and so on.

    When I first open Firefox it is fine but if I open a second tab to search another site I get a white screen and have to continually click 'back', click the site link, white screen, back, click the link, white screen and so on.

    This can also be a problem with the files [http://kb.mozillazine.org/sessionstore.js sessionstore.js] and sessionstore.bak in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Profile Folder]
    Delete [http://kb.mozillazine.org/sessionstore.js sessionstore.js] and sessionstore.bak in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Profile Folder]
    If you see files sessionstore-##.js with a number in the left part of the name like sessionstore-1.js then delete those as well.
    You will have to redo App Tabs and Tab Groups after deleting sessionstore.js.
    See:
    * http://kb.mozillazine.org/Session_Restore

  • Mac Mini Intel boots to blue screen and gets stuck

    Mac Mini running 10.6 Intel won't boot up. I get the chime, then the apple logo, then a blue screen, then nothing but the small rotating circle, which appears and disappears about every 5 seconds (not the color wheel, but the one that just looks like hands on a clock turning.)
    Per apple online help, tried starting up in Safe mode. Same result. No boot. Just blue.
    Per apple help, I started up in Sinlge User mode and ran Fsck from command line (I don't have the install disk). First run of Fsck said FILE SYSTEM WAS MODFIFED. Ran it again, per apple help. Second time, said volume appeared to be OK. Typed "reboot". Same result. No boot, just blue screen and rotating circle.
    Not sure what else to try. Any help?
    Thanks

    Sometimes PRAM seems to retain info from a previous startup disk error condition. There is a small chance that resetting the PRAM might help.
    You can get a replacement for your original OS X install DVD and any bundled apps from AppleCare (1-800-275-2273) for a shipping and handling fee. You will need to provide your Mac's serial number so they can send the correct DVD(s) for your specific model.

  • Mac Pro is booting to blue screen after installing a new Optical Drive

    I am trying to install a new Pioneer 115D Optical Drive in the 2nd Drive Bay. After installation I turned back on my computer and it did not boot. I got to the blue screen and the computer just hung there. Any suggestions on what went wrong? I have read something about switching to cable select how might I go about doing that? Also Someone suggested to remove the drive lip. Does that need to be done before installation? I watched the OWC video and followed the instructions there but there was no mention about removing the lip or using Cable Select. Thanks for you help.

    You have to remove the tray lip before putting the drive in the computer
    <http://eshop.macsales.com/tech_center/index.cfm?page=removedrivedoor.html>
    When you reinstall the drive holder, make sure it doesn't slice or pinch any of the cables.

  • When I take a picture with the flash on auto, I get a blue circle and no picture. When I turn the flash off the  picture comes out fine. What do I do to take a pic in low light

    When I take a picture with my iphone 4 and the flash is on I get a blue flash and a big blue screen with no pic. When I  turn the flash off the pics come out
    fine. I turn the flash on to take a pic in low light I just get a blue screen. How do I remedy this?

    Try a reset or restart of the device.
    If that doesn't work attempt a restore of the phone's iOS

  • After login I get a blue screen and then back to login window, but only for one account

    When one of the users on the iMac tries to login it goes to a blue screen and back to the login window.  This only happens with one of the users - I've tried doing a safe boot, running disk utility, and using Time Machine to restore the user's libray back to pre-problem timetable.  When I run repair permissions I do gt a SUID file "usr/sbin/vpnd" and "usr/sbin/pppd" have been modified.  Any ideas?

    Try this...
    http://reviews.cnet.com/8301-13727_7-20013630-263.html
    If that doesn't help I'd make a new user & use an admin account to move the old folders over & change rights to the new user.

  • Reposting from Mac Pro forum - rthdaud.sys blue screen problem

    Hi all, have been playing around in boot camp (gaming for the most part) and twice now have, after a few hours of perfectly fine system running, been presented with a blue screen naming rthdaud.sys as the cause. As this is the realtek audio high-def driver, I assume it's part of the boot camp driver package and should be okay.
    What would be the first thing to try? Should I reinstall the apple boot camp driver for this? Perhaps get the driver (updated version?) from realtek's website directly? Thanks in advance for any help.

    In two years running Vista 80% on Mac Pro, never had or seen an issue... possible there is something hardware wise wrong instead? or bad install?
    Apple Hardware Test run?
    In Vista have you ever run system file checker?
    sfc /scannow
    and chkdsk of course, don't know if side effect of freezes lead to file damage. Or if your hard drive just has a bad block even.

  • Why does my Mac Pro randomly flash a blue screen to both monitors?

    For a while now my Mac Pro (Early 2009) has this occasional issue. The system uses a pair of ViewSonic 22" monitors. At random times, both monitors just turn to a solid light blue color. After a brief time (1 to 5 seconds maybe) normal operation returns. The system is still working. Text typed on the keyboard during the 'blue' screen still shows in whatever application I'm in. Just the screen seems to be affected.
    I leave the system running 24/7 with only occasional reboots (weeks or months apart). The screens I turn off at night. Most of the time this happens right after the system 'wakes' in the morning (temperature does not seem to be a factor). Although the system is doing this as I'm typing this. The blue screens show up than go away on their own. This repeats from one to ten times before it goes away. Once it is 'done' everything is normal until it happens again.
    This 'issue' has been occurring since the original Snow Leopard. But, it also happened with Lion and now still happens with Mountain Lion (just upgraded to 10.8.2).
    I am thinking this has something to do with the graphics controller (NVIDIA GeForce GT 120 512MB). But, I've never found any online references to this sort of behavior.
    Any comments or suggestions will be appreciated.

    The cable connections have (so far) solved this problem for my situation. Even though the monitor's DVI cable was firmly connected to the mini Display port connector, when I touched it the attached monitor would go 'blue' or lose its connection entirely. After disconnecting and reconnecting this junction the monitors would still take a hit on touching the connection. I also checked the connection of the mini Display port connection to the graphics board and could not push it in any further. However, after a second go-round I unplugged this connection to the board and reconnected it. I am certain it was fully inserted the first time. But, connection contacts can oxidize over time and sometimes it may just need to be disconnected and reconnected to 're-wipe' the connections. This effectively cleans them at the point of contact. So in my case I'm thinking it was the connection age that was an issue more than a 'loose' connection. Either way, I haven't had this issue for the past two weeks.

  • TS2570 after startup, my macbook pro goes to a blue screen and stays.  this article says it won't work for the blue screen problem... any ideas?

    My Macbook Pro stays on a blue sceen after start up.  It won't boot into safe mode (holding down the shift key).
    What do I do?

    Hi Mindy, it may though, did you try it?
    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
    If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
    If 10.7.0 or later...
    Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.

  • Cannot get into mac. I get a white screen and flashing file folder with question mark inside. What can I do?

    2012/13 MacBook Pro froze up, so I did a hard shut down. Now, when I try to start up, it makes 3 unusual beeps, then I get a white screen. After a couple minutes, a flashing file folder with a question mark appears and remains. What is wrong and what can I do to fix it.

    Three beeps usually means a RAM or RAM slots problem. The Question Mark means there is no bootable system found.
    A flashing question mark or globe appears when you start your Mac
    Question (?) Mark, Blinking Folder, or Gray Screen at Startup
    These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
    A flashing question mark or globe appears when you start your Mac
    Mac OS X- Gray screen appears during startup
    In most cases the problems may be caused by one or more of these:
    a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
    b. Boot drive's directory has been corrupted - Repair with Disk Utility.
    c. Critical system files are damaged or deleted - Reinstall OS X.
    d. The disk drive is physically non-functional - Replace the hard drive.
    Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
    Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
    Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
    Reinstall Snow Leopard Without Erasing The drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.
    Reinstalling Lion/Mountain Lion Without Erasing The Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • Power Mac G4 starts, gets to gray screen and shuts down

    My Power Mac G4 will start up, but after it gets to the gray screen with the Apple and the spinning gear for a minute or so the computer shuts down. I have started the computer while holding down the "C" with the 10.4 OS disc in and used the Disk Utility to run First Aid. First Aid fails stating:
    __*Keys out of order*__
    __*Rebuilding Catalog B-tree.*__
    __*The volume Macintosh HD could not be repaired.*__
    __*Error: The underlying task reported failure to exit*__
    __*1 HFS volume checked*__
    __*1 volume could not be repaired because of an error*__
    __*Repair attempted on 1 volume*__
    __*1 volume could not be repaired*__
    I have attempted to start computer in safe mode but it just shuts down... no difference.

    Faurot, welcome to Apple Discussions
    You have directory corruption on your hard drive that Dusk Utility can't repair. DiskWarrior can probably fix your problem. DiskWarrior by Alsoft
    http://www.alsoft.com/DiskWarrior/index.html
     Cheers, Tom

Maybe you are looking for