Original Airport Cart can;t locate network? Help!!!!

I have a 2002 quicksilver g4 with the original airport card installed. It had been working flawlessly up until recently when it can;t locate the wireless netowrk in my home. I know it it's recognizing the card because it doesnt say "no airport card installed". I also know the nework is working because the two ither computers in my home locate the network and connect no problem. Any possible solutions?
quicksilver 2002 Mac OS X (10.3.9)

Hi Brian,
I'm a big fan of just "starting over." Somehow, a glitch got introduced. Rather than digging around and trying to find the glitch, and possibly introducing more in the process, why not start over? (If you like figuring glitches out, ignore the following...)
Turn off airport on your g4. Delete references to your network in "Network Preferences" and in Keychain access in utilities. Reconfigure your wireless router to factory defaults. Restart your wireless configuration. Once all computers are up and running wirelessly, reintroduce wireless security.
Good luck

Similar Messages

Airport Express can only extend network, not create new one. Why?

I am sharing a flat with some friends. The shared broadband router is placed in the living room. To strengthen the signal and make it easier for me to manage, I bought an Airport Express, connected it to the shared router with an ethernet cable and set up a wireless network of my own in my room. It was working fine, until recently we renewed our broadband contract. The router had been replaced by a new one (I don't know why) and the network configration had been changed. Since then I was not able to use my own network. In the Airport Utility display, the light of Airport Express is green, but the light of Internet is yellow, and the status is disconnected. I tried to change various other configuration on the Airport Express, and all in vain. Until I switched the network mode from 'Create a new wireless network' to 'Extend a wireless network', the Internet connection was finally back online. But this merely extends the existing network and not what I want. Why this happens? Why my Airport Express can only extend a network, not create one?

Here is the situation on my Airport Express.
If I choose to extend the existing wireless network, the Airport Utility shows like this:
If I set up a wireless network of my own, what I get in the Airport Utility is this:
See my problems here? The Airport Express does not show anything in amble, but the Internet complains that there is no connection.
This problem did not occur before the broadband was renewed and the rounter was replaced.

HT4759 My iPhone is on and I still can't locate please help

My iPhone is on and I still can't locate please help

Many site issues can be caused by corrupt cookies or cache. In order to try to fix these problems, the first step is to clear both cookies and the cache.
Note: ''This will temporarily log you out of all sites you're logged in to.''
To clear cache and cookies do the following:
#Go to Firefox > History > Clear recent history or (if no Firefox button is shown) go to Tools > Clear recent history.
#Under "Time range to clear", select "Everything".
#Now, click the arrow next to Details to toggle the Details list active.
#From the details list, check ''Cache'' and ''Cookies'' and uncheck everything else.
#Now click the ''Clear now'' button.
Further information can be found in the [[Clear your cache, history and other personal information in Firefox]] article.
Did this fix your problems? Please report back to us!

MacOSX 10.3.8 system with original Airport card can't connect via WPA/WPA2

Hi all,
My WiFi network consists of an Airport Express running a WPA/WPA2 Personal network and 802.11b/g compatibility, upon which 3 Macs (all with Airport Extreme/G or /Draft-N cards) and 2 PCs (both G compatible) merrily connect to.
I have an old PowerMac G4 which I've just fitted with an original non-Extreme Airport card, and having updated MacOSX 10.3.8 with Airport 4.2 to enable WPA access, it still refuses to connect to the network; I get the "There was an error joining the Airport network ..." when the correct password is entered.
My understanding is that while the old Airport cards don't support WPA2, they do support WPA and thus if the Airport Express network is set to WPA/WPA2 and b/g compatibility (which I'm assuming is some kind of all encompassing compatibility mode, given there's also sole WPA2 options) then it shouldn't have any problems connecting to the network. What am I missing here?
Cheers, Ben.

I am having the exact same problem. Powerbook G4; original factory installed airport card; with Panther 10.3.9 OS plus updated 4.2 Airport Admin. Utility. It will NOT connect to my Airport Express set to the WPA/WPA2, which is working fine with my iPod touch.
When I get to the screen requesting password for my chosen airport network ("Wireless Security: WPA Personal), the "OK" button is grayed out and it will not even let me submit a password to connect. Can somebody help?

My airport express can't locate a dns server

I am unable to connect to the Internet, with my Mac,iPad or iPhone, even with the light green. I used my airport utility and it can't find a Dns server.
I called my Internet provider and they said everything looked alright on there end.
Does any body know what it might be?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref:Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

CUPS can't locate network printer

I don't know if this is a network issue, or a PKGBUILD issue.
I have a Brother printer that is not one of the ones for which there is an AUR package already. So I just copied a PKGBUILD and .install from a similar model's AUR package. Here they are:
PKGBUILD:
# Based on brother-mfc-j625dw package from AUR
_model="j435w"
pkgname="brother-mfc-$_model"
pkgver="3.0.0"
pkgrel=1
_revision=1
pkgdesc="LPR and CUPS driver for the Brother MFC-J435W"
url="http://welcome.solutions.brother.com/bsc/public_s/id/linux/en/index.html"
arch=('i686' 'x86_64')
license='unknown'
install="brother-mfc-${_model}.install"
depends=('tcsh' 'deb2targz' 'perl' 'a2ps')
if test "$CARCH" == x86_64; then
depends+=(lib32-glibc)
fi
source=("http://www.brother.com/pub/bsc/linux/dlf/mfc${_model}lpr-${pkgver}-${_revision}.i386.deb"
"http://www.brother.com/pub/bsc/linux/dlf/mfc${_model}cupswrapper-${pkgver}-${_revision}.i386.deb")
build() {
deb2targz *.deb >/dev/null || return 1
rm -f *.deb || return 1
cd $srcdir || return 1
[ -d "mfc${_model}" ] || (mkdir mfc${_model} || return 1)
for i in *.tar.gz;do tar xfz $i -C mfc${_model};done || return 1
cd mfc${_model} || return 1
cd opt/brother/Printers/mfc${_model} || return 1
perl -i -pe 's#/etc/init.d#/etc/rc.d#g' ./cupswrapper/cupswrappermfc${_model} || return 1
perl -i -pe 's#printcap\.local#printcap#g' $srcdir/mfc${_model}/opt/brother/Printers/mfc${_model}/inf/setupPrintcapij || return 1
cp -rf $srcdir/mfc${_model}/usr/ $pkgdir/ || return 1
cp -rf $srcdir/mfc${_model}/opt/ $pkgdir/ || return 1
md5sums=('7f891cbaddc07a1b86902c9c67cbcccb'
'8756f5964a9f9f811cc1b855f7593c2f')
brother-mfc-j435w.install:
post_install() {
post_upgrade;
post_upgrade() {
/opt/brother/Printers/mfcj435w/cupswrapper/cupswrappermfcj435w >/dev/null
if [ "$?" -eq 0 ]; then
printf "\033[1m\033[32m\x3d\x3d\x3e\033\1330m Done. The printer should be visible now via the CUPS-webinterface (http://localhost:631)\n"
else
printf "\033[1m\032[32m\x3d\x3d\x3e\033\1330m Something went wrong...\n"
fi
So, then I open up the CUPS web interface and voila, I see MFCJ435W ready to go! So, I print a test page and it fails with "Unable to locate printer "BRN0080928DFDD8.local"."
I have no idea what to do to diagnose and fix my problem. Help?

Do you have a mdns service configured? I am not sure if this is related, but zeroconf/avahi's .local domains get resolved by a multicast dns infrastructure:
https://wiki.archlinux.org/index.php/Avahi
oh found this: https://bbs.archlinux.org/viewtopic.php?id=127964

Original Files Lost - Can't locate anywhere??

I purchased & connected a Dynex adapter to my laptop after losing my original Ipod cable. When I installed it some type of "convergance" took place. ALL of my original music with the exception of 2 CD's dissapeared. It is not in iTunes, Music Library, m4p files, recycle bin, anywhere on C drive.
I then downloaded latest version of iTunes & QT realplayer. WOW all of my music has re-appeared in iTunes. But none of the original files can be found, ANYWHERE...I looked in all of the above mentioned places. Every song has an exclamation point next to it. My iTunes library still contains only the 2 CD's it had remaining after this originally started. Sorry so long. I searched the forums for an easy answer, nothing found. ANY SUGGESTIONS?? Thank you.

What is that Dynex adapter thing? What did you have to install to use it? I don't know what you mean by
When I installed it some type of "convergance" took place.

Airport card can not see network.

I have recently moved. I had no issues with the my network on my G5. We moved, I bought an Airport Extreme and set it up through Qwest DSL. My G4 laptop, my iphone, my roommates G4 laptop and his dell laptop all successfully see and login into our network just fine. However my G5 doesn't see any network available. Like I said, in our old spot, everything was fine. Any Suggestions? Thanks in advance.
Wireless Card Type: AirPort Extreme
Wireless Card Locale: USA
Wireless Card Firmware Version: 405.1 (3.90.34.0.p18)
Current Wireless Network: wireless network not available

I've been experiencing similar difficulties with connecting to my wireless router and dropping signal connections.
It almost seems to be in the same vein as SCSI voodoo. One day it works and another it doesn't.
One thing that seems to reduce the problems is to use only WEP protocol. I have rarely been able to connect using any of the stronger schemes, although my wife and daughter using pro laptops have few problems with connections.
My G5 does not have an external antenna, which I suspect is part of the problem.
Mike

New 10.3.9 install on Pismo G3, Airport Extreme Base Station Error Network

My 10.3.9 Pismo laptop G3 with built in firewire ports worked perfect on my Airport Extreme Base Station — I just Erased and reinstalled 10.3.9 (it was working before I Erased this morning) and now my Original Airport card can't join my wireless network:
*"There was an error Joining the Selected Network"*
I zapped Pram, reset power manager successfully (date reverted).
I accessed the AEBS by a 10.6.3 Mac Pro and checked the Equivalent Password "WPA Password: ####PW###"
Radio Mode selected: 80211n (80211b/g compatible).
APBS version current: 7.4.2
G3 sees my network as expected.
The APEBS hasn't changed (except for the recent update).
I restarted the AEBS.
Still get the error...HELP!
I saw the exact problem on several archived threads, but no one gave a solution or explained the problem (and I'm going blind here).
Again, for the past two years it was working fine with 10.3.9, it broke this morning after I erased and reinstalled 10.3.9.
10.3.9 is the only software loaded on this laptop.

If you just bought it I would recommend calling Apple, they can help you set it up.
Also you should consider getting a high speed Internet connection. They are very inexpensive these days and would make your Internet experience much more enjoyable. Where you live I would think you have a choice of DSL (available from most telephone companies) or Cable, which would be the quickest but also more money too.
Regards,
Roger

Original Airport cards and e-Bay

I have a 17inch flat panel iMac, 800 mhz speed and am thinking of going wireless. I know I need an original airport card for my computer, NOT the airport extreme. I have been searching on e-Bay and found various sellers with a huge difference in prices. My question is: are there different models of the original airport card? One vendor lists an airport card model # M7600LL/A for a high price, but in the information it lists my computer as one of the models this card will work with. Another vendor has an airport card model # M7600LL/E for a much lower price but the information on the card's compatability is rather sparse. Are they the same card just with a different price? What is your advice about buying an airport card from e-Bay in general? I will also need a wireless router and have my eye on a Linksys model that a few of my friends have in their wireless networks and they recommend it highly. Any thoughts on that area?
17 inch Flat panel iMac, 800mhz Mac OS X (10.3.9)

Basically the difference between the two is one was for American market I believe and the other the European market.
Both should work fine.
Original Airport Card Alternatives
http://www.ifelix.co.uk/tech/1030.html
A Mac with an original Airport card can connect to any wifi certified 802.11b wireless network (or 802.11g in backward compatible mode).
Out of all the different wireless routers I have used, I have found my Airports to be reliable and easy to setup.

Is any document about GRC or IDES system can be located?

Hi expert,
Can you please tell me how can I access the IDES system of GRC?
Where can I locate the help document of GRC as access to the help portal of SAP?
Thanks.

Documentation on Trade Compliance (Global Trade Services) and Environmental Compliance (EH&S) is available on http://help.sap.com. The user and installation guides for GRC Access Control and Process Control are currently accessible together with the software download (requires a software license). We'll soon have that documentation on http://help.sap.com.
All compliance software is available for demonstration, some of it on IDES systems (trade compliance, environmental compliance), some on dedicated demo servers (access control, process control).

I'm looking for some help connecting linksys IP Cameras to my home network to monitor my property when I'm travelling. I used to do this with linksys WAPS, but since I've discarded all my old linksys networking and standardized on airport, I can't get the

I'm looking for some help connecting linksys IP Cameras to my home network to monitor my property when I'm travelling. I used to do this with linksys WAPS, but since I've discarded all my old linksys networking and standardized on airport, I can't get these things working. I know that I have to identify my camera through the DHCP table and set up port forwarding and there is the problem.
My network consists of 4 base stations set up in a roaming network - same network name and passwords. I need to do it this way so I don't have to switch network when I move from one side of the house to the other, go to the cabana, or my shop in the barn. The network works pretty well since I went to a roaming set up. Good performance, yata, yata, yata.
However, the roaming network requires the AEBS's to be set up in bridge mode, rather than sharing an ip address. When the AEBS is set to bridge mode, you don't see a DCHP table or have the ability to identify your IP Cam through the AEBS - and hence, no port forwarding.
I am able to identify and set up my Linksys IP Cam by locating the ip address on my FIOS router, even though, it's plugged into an AEBS. I set it up, see the video, remove the ethernet cable from the IP Cam, restart - and I can't get to it from an AEBS. In researching this, it appears, I should be setting up the AEBS to "share an IP Address", going to the DHCP table and identifying the camera's IP address and setting up port forwarding. However, you don't see any of the DHCP or port forwarding options in Airport Network Utility when configuring in bridge mode.
I'm hoping I'm missing something here and that the solution isn't to set it up at the FIOS router level, but I'm beginning to think that's my only hope. What concerns me there is that I should be able to see the IP cam on the network without port forwarding since I'm not coming from outside, and I can't even do this unless it's connected hard wire.
I'd appreciate any insight into this that anyone might have. I've hit the wall with what I know.
Thanks.

In a roaming network, your "main" router is the device that would require port mapping/forwarding to be configured in order to access the IP camera from the Internet. This router is also the one that would be provide the private IP address for the camera which you will want to be a static one.
So as you described your network, the IP cameras should be getting an IP address or you assigned it a static one and this is the address that you would enter in the Private IP address (or equivalent depending on the router used) field when setting up port mapping.
If you are not able to access this camera from the local network, then this should be troubleshot first.

HT4587 I can't locate airport express icon in itunes to connect my remote speakers wirelessly, can anyone help please?

Can anyone help please? I am trying to connect my remote speakers to my i-tunes library using Airport Express. Everything is connected and working using mt OS device (Ipod Touch 5th Generation) that works fine. I have tuned on home sharing and it says in itunes preferences that I am paired but according to the light on the airport express base station I am not connected to my existing wi-fi network. I cannot find the itune airplay icon anywhere in itunes nor can I find the network link by hovering my pointer of the network connections as suggested in the instructions that came with airport express. Would apprecaite some help please you can give. - thank you.

hmmmmm.
i'm not trying to get rid of you here, but it might be worth also checking-in/reposting over at the Airport for Windows forum. when Airtunes things get sticky, i generally defer to iFelix or RJ in WI, and they spend a lot more time over there than they do here.
(traffic is so heavy in here at the moment that this thread might be buried out of sight before an AirTunes guru gets to see you.)
here's a link through to the Airport for Windows forum:
Airport for Windows

I have tryed to connect an AirPort Express to my wireless network. But I alwais get the errocode -4. Can anybody help. I have reset the AirPort Express and updated the software.

I have tryed to connect an AirPort Express to my wireless network. But I alwais get the errocode -4. Can anybody help. I have reset the AirPort Express and updated the software.

The ZyXEL P-2601HN-F1, as you know, is a combination DSL modem & 802.11n wireless router (or gateway device).
For your goal you will want to take a look at this Apple Support article for details on how to configure an AX for iTunes.
If you are still having difficulties with the AX joining the ZyXEL's wireless network, you can try the following:
Temporarily disable wireless encryption.
If you are hidding the SSID, disable that feature.
Change the Mode Select setting to: 802.11g Only
Change the Channel Selection from "Auto" to a set channel, like 1, 6, or 11

Can't get my original airport express to connect to new network

I have an original airport express and just changed to a new comcast xfinity router. Airport utility now doesn't see the airport express. Have tried the reset button and still the new network doesn't see it. Am I gonna have to buy a new airport?

Similar situation. Want to use an existing Airport Express on a new network. I did the factory reset. Saw the 4 fast green blinks, and it's now slow-blinking gold. AirPort Utility, however, doesn't see any other Wi-Fi devices. "No remote AirPort Stations discovered." The AE is about 10 feet away from my Time Capsule. My MacBookPro is within 2 feet of the AE and connected to the Time Capsule network.
What next?

Original Airport Cart can;t locate network? Help!!!!

Similar Messages

Maybe you are looking for