OS 9 Not booting in 10.3.9

Every time I try to start Classic in one of my computer's user accounts, it stops right when I think its about to be finished. The Mac OS 9 box with the starting up message goes away completely and it just sits there forever. The odd thing is that it only happens on that one user, not on the other two on the system. What can be done?
Thanks

Try the instructions in this article. The file Robbie Goodwin mentioned contains the computer's MAC address in the filename, and therefore will not be present with that name on any other computer in the world. The sequence of 12 hexadecimal digits is different on different machines, and is unique to each machine.
(13847)

Similar Messages

Satellite C850-1NU does not boot Win 8.1 - Error Code 0xc0000098

Windows 8.1 will not boot
Laptop is *Toshiba Satellite C850 1NU*, as from Saturday it will not boot up!
*Error states "The boot configuration Data File doesn't contain valid information for an operating system.*
*File:\ BCD*
*Error Code 0xc0000098*
I have transferred recovery tools from another laptop to a USB stick and then enter bios of the Toshiba Laptop to make the USB drive to boot first.
It then comes up with the recovery tools.
I clicked on "Refresh your pc" it then reports "The drive where Windows is installed is locked. Unlock the drive and try again".
I clicked on "Reset your pc" it then reports "Unable to reset your pc. A required drive partition is missing".
I have also tried "Automatic Repair" and it reports "Repair couldn't repair your PC".
I am at a loss as to get my sons laptop up and running again. Advice would be much appreciated. Thank you.

Further to my question, *I have now resolved the issue.*
Thanks to phanlon7 on this link
[http://answers.microsoft.com/en-us/windows/forum/windows_8-system/windows-crash-refresh-hard-drive-locked-unlock/a6bb04ff-5dba-4e10-a849-644cd0851bc6?page=2&rtAction=1390385080363]
I used a usb stick and copied recovery from another windows 8 laptop.

2009 Mac Pro will not boot up under Windows

I have an Early 2009 Mac Pro system (Mac Pro 4,1) and I've had this system for 3 years already and have been working under OS X with this system ever since I purchased it.
However, when I tried to boot off my Windows disk, something very interesting happens. The Mac Pro WILL NOT boot up off the Windows disk or a known working Windows partition if two monitors are connected. Upon holding down the option key and selecting the Windows partition, I will get a black screen on one monitor (the one connected via Mini Displayport) and the other screen receives no signal and will enter standby and the system is halted. It does not respond to keystrokes, there is no hard drive activity, no measured power increase on the UPS, no apparent network activity, nothing. The only way to exit this scenario (from what I can tell) is to power off the machine, disconnect the display on DVI, power on the machine again, select the Windows partition wait for the system to reach the login window and reconnect the DVI monitor (at which time Windows recognizes it immediately and the system works fine again).
My question to the community is, does anybody know why this is happening and is there a known fix for this? Quite frankly, having to disconnect a monitor just to restart is very tedious and frustrating.
I have two Samsung P2350 monitors attached to an ATI Radeon HD 4870 (512MB, from Apple). One is monitor is connected via directly DVI and the other is using a Mini Displayport to DVI adapter. Both monitors work fine under OS X with no issue. At first, I thought that this may be a driver issue on the Windows side and after installing all the latest updates and drivers the issue is still apparent. From what I can tell, this doesn't seem like a software issue but rather a firmware or EFI issue as this happens before Windows even loads.
If anyone knows of a fix or what to do in this situation, or if you are also having this issue, I would love to hear your input!
Thank you!
For the record, I am running all the latest software builds on the OS X side (10.7.4, not that it would really matter at this point). I have also disconnected all unnecessary equipment in a trial and error scenario but the results are still the same.
The system passes all ASD testing.
The full specification of the computer and all connected equipment are as follows:
2009 Mac Pro (4,1) 8-Core
2x Intel Xeon Nehalem 2.66GHz Quad-Core CPUs
16GB DDR3 ECC 1066MHz RAM (Apple Branded)
Two OWC 120GB SSDs (One for OS X, the other for Windows 7 x64) - These are in place of my optical drives.
4x 2TB WD Black Hard drives for storage.
Two Samsung P2350 Monitors connected via DVI. (One using a Mini Displayport to DVI adapter).

In Windows I am using the latest (12.4) Catalyst Software Suite, 64 bit of course, downloaded directly from AMD's site after installing the drivers from Boot Camp.
As for installing Windows I used an original (not burned) installation media (Disk is in a pristine condition). And yes, Windows is fine, the problem just seems to be getting the system to boot up Windows with that second monitor. However if the "problem monitor" is disconnected the system boots fine 100% of the time and connecting it later after booting the system will still operate properly.
For the sake of arguement I swapped monitor cables and connected the "second" monitor to the mini displayport adapter to verify that it wasn't a cabling issue and I'm still yielding the same issues.
As for GPU testing, I've played games (Crysis, Grand Theft Auto IV, Battlefield 3, etc.) and I've had no issues with the card or stability.
You would think that Apple would try to find a fix for this, especially considering the caliber of this machine.

Reset CMOS, system will not boot

This is a long story but I will try to keep it short:
I just bought a new 875P Neo-FISR and a 3.0 GHz Prescott, which from reading the other posts could have been a mistake. I installed the CPU, memory, and the video card and pressed the power button and received a "CMOS Data Wrong" error. So I tried to correct the problem but when I saved and exited then the system would not boot back up. So, I reset the CMOS via the jumper and tried again. After MANY attempts I change just the month in the date setting. And what do you know...it would not boot back up. The D-Bracket LEDs were: 1-flashing red/green, 2-flashing red/green, 3-red, and 4-red
I must have read almost every post in this forum and tried many things such as:
disconnecting all componets except for video, ram, and cpu
the during boot to recover the BIOS
removing mobo from case, maybe a short
moving the memory to different slots
moving the PSU to a different computer...it works
disconnecting the PSU from the mobo and and removing the battery overnight. The first night I did not disconnecting the PSU from the mobo and I found that did nothing.
Tryed everything that I could think of and some stuff that others thought of but nothing worked. However the last item...removing the battery...did change things some. Now nothing happens, and I mean nothing...no lights, no fans, no buzzing...nothing.
Any ideas would be greatly appreciated. The only recourse I have left is to RMA the board.

I tried one stick in all of the slots with and without the sound card. That did not work either.
The voltage for my memory is 2.6 so that is what I tried. But if I can get it to boot up again I will try 2.7.
Tks.

PowerMac G5 will not boot up

Hello all -
I have a PowerMac G5 Dual 2.3GHz (early 2005) that has recently started to have issues. It froze a few times in the last week, and then would not boot up again. I dug out the original install disks, and was able to boot and run the Apple Hardware Test. The hardware test revealed a stick of RAM that was giving errors, so I removed the bad memory and it's mate (since they are required to be installed in pairs). Everything was great for a few hours, and then it froze up again. Had to hold the power button to force it to shut down. Once again it would not boot up - either a black screen, or stuck on the gray screen with the Apple Logo on it. Again was able to boot to Hardware Test from the install disk, and ran the Test again. This time it came back with no errors or problems. Ran it several times, all without any errors. I have reset the PMU, unplugged the power cord for several minutes, swapped memory around to different slots, unplugged everything but the monitor, keyboard and mouse, .... all to no avail. The computer will not start up. I tried to use the CD as a boot disk, but it hangs the same as when trying to boot from the hard drive. The only thing it will do is boot into Hardware Test mode (from the install disk), or Firewire Target Disk Mode (fortunately, since I can at least access my data and make some backups).
This computer has been very reliable up to now, and this all came on quite suddenly.
Any ideas?
Thanks.
PowerMac G5 Dual 2.3GHz
1.5GB RAM (after removing 2 512MB sticks that gave errors)
OS 10.4.11

Ok, so this has now advanced to the point of being a bit ridiculous.
The nearest Apple store is 45 miles away, but I happened to be in the area over the weekend, so I brought along my G5 for a visit to the Genius Bar. A resident Apple genius hooks it up, powers on, and lo and behold, it boots. What? How is that possible? I have been unable to get past the gray screen for weeks. He mentions that sometimes if you unplug everything, it will help to reset the power management, etc. So I tried to remember, did I leave the keyboard plugged in while it sat in the corner? Dunno, but it certainly booted fine in the store. He then ran the proprietary Apple Diagnostics (very low level testing, much more thorough than the Apple Hardware Test we consumers have access to). Took 30-45 minutes. Came back without so much as a hiccup. Everything checked out perfectly. He could not reproduce any problems at all. Hmm. Well, ok, awesome. It's all good to go!
So, I get home, hook everything back up, and it runs fine. My wife is happy that she has her computer back. It runs for a day or so. Then it locks at the login screen while trying to wake from sleep. The fans ramp up to full speed. Have to hold the power button to shut it down. Restart, everything's fine again... for a few hours. Next morning it is frozen again, and will not progress beyond the gray logo screen. Never gets to the spinning gear. I unhook everything again, wait an hour, and try to boot again. Get a kernel panic. Force restart again, and now is stuck at the gray screen again.
So..... What in the world is going on? All of the hardware has passed Apple's low level testing with no problems, yet it no longer functions. I have a feeling that if I leave it for a week, I will get a few hours use out of it, then it will freeze again.
This is all very frustrating. Anyone interested in a used G5 tower with intermittent issues?

Macbook Pro will not boot up normally ***Not Normal Problems***

Ok. I have an older 17" Macbook pro 2.33 (10.6 fully updated) that will not boot up in normal mode. When I boot it shows "blocks" of different colors and will not get past the blue screen sometimes. When it does get passed the the blue or grey screen it is a split screen of white back ground with large black blocks seperating the sides. I have tried swapping out harddrives with a known working one with an OSX image on it-no good. I have tried swapping out ram-same thing. I reset the SMC and PRAM-only colors changed in the blocks. I have ran disk utilites disk and permisions with no problems. I can't boot into a restore disk using the c key during boot, It locks up at the same screen. Nothing works except safe mode. I can boot into safe mode and everything works just fine with normal screen and all. Now I tried runing the Lion installer thinking it is and driver issue but I can't get Lion to boot to the hard drive and Snow leopard just reboots back to the same screen. So how can I get Lion to install or Snow Leopard?
What can I do? I noticed this last weekend when I tried to reboot my MB Pro and it started this. Well Apple pushed and update last friday - I needed to restart it again and this happends. I thought it was a logic board at fist until it booted fine in safe mode.

Sorry. What I mean is I selected the SL boot up in the start up panel and it would not boot into the cd. The CD rom sounds like it just keeps reading with it slowly loading from grey screen to blue screen to the Block screen. Almost like it is booting into normal mode from the hard drive.
What I can't understand is why it runs fine is Safe mode?
Also why do I get a " this disk cannot be used to start up your computer" message on my hard drive when trying to install Lion in safe mode? Well why not it's the only hard drive in the computer?
The first screen shot is the Tech tool showing everything passed the hardware test is safe mode.

Computer will not boot up after recent software install

I recently tried to install a series of software updates. Not all were successful. Soon therafter the computer froze up while in safari. I turned it off and the computer would not boot up on restart, and instead sent me to the darwin login screen. I rebooted in safe mode per these forums, and turned off an itunes startup function, and then rebooted. That seemed to do the trick as I could now get back into the OS, but the computer was dreadfully slow. It froze up again in Safari and I turned it off again, and this time it would not go past the grey startup screen with the apple. I tried safe mode again, but the computer would shut down around 30 seconds after the wheel below the grey apple started turning. I Was able to get my Tiger Install DVD in the drive, and turned the computer back on, but now just get the grey apple screen and the wheel spinning indefinitely. I cannot do an erase and install because my photos are not backed up. Please help!
Thanks

Hi, Deaton41. Welcome to the Discussions.
You wrote: "I recently tried to install a series of software updates. Not all were successful."I suspect the only way you are going to resolve this is by performing an Archive and Install. For important tips on this process, see my "General advice on performing an Archive and Install" FAQ. Perform the steps therein in the specified order. If you follow my FAQ's steps to the letter, then your photos should be AOK, assuming directory corruption hasn't damaged them. I suspect directory corruption is the root cause of the unsuccessful software updates, which that then led to your current problem re: start up.
Before installing future software updates, you may wish to consider the advice in my "Installing Software Updates" FAQ. Taking the steps therein before installing an update often helps avert problems and gives you a fallback position in case trouble arises.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Upgrade BIOS and drivers have possibly corrupted drive. OS will not boot.

Model: Toshiba P505-8980
Part Number: P6PG0U-005002
OS: Windows 7 Professional 64-bit (upgraded from Home Premium)
6 gig RAM, 500gig HD
Actions:
I haven't started up my computer in a while. First I installed the critical and optional updates (3 total) from windows update, rebooted, and Toshiba Service Center popped up and said that there was the BIOS 3.10 update and the HDD/SSD Alert update. Through the Service Center I downloaded and installed the BIOS update, at the end it seemed as if there was an error. I rebooted the computer and everything seemed ok, so I downloaded the HDD/SSD update through the Service Center. Upon rebooting the drive would not boot. (Screen remained blank with a blinking cursor and HDD light was not on.) There are no accessories/USB devices/drives attached. After a reboot I checked the BIOS and it recognizes the Hard drive, I restored all settings in BIOS to default and rebooted. The computer started receiving stop errors (blue screen) and stuck in a reboot loop. I entered the BIOS, restored default settings again and rebooted, I could get to safe mode and it would receive stop errors trying to load disk.sys file. I also tried last known good configuration and that wouldn't work either. After a while the laptop was able for me to select to try and repair the disk using the repair utility. It reported that there may be partition errors (on the last step of recovery) and I selected to repartition the drive to factory default with the Toshiba repair tools. It got to about 98-99% and received errors at the end. I tried using a Windows disk to reinstall the OS, but it reported it couldn't install on any of the drive partitions because of an error in the boot configurations. After trying to repair again it doesn't report any disks or partitions. Currently after booting it reports now that there is an error that occurred while attempting to read boot configuration. File: \Boot\BCD|Status: 0xc000000f. Guessing that the boot sector got corrupted. After reading that BIOS isn't recommended to be installed while in windows, I'm wondering if using the service center messed something up.
Question 1: Any recommended actions to take now? No recovery disk available
Question 2: Is there a way to configure the service center to download a BIOS update and be able to save it instead of only being able to install it within windows and the service center?
Thanks in Advance!

I was able to get into system recovery. This system recovery was different then the first one I came across. Underneath the Command Prompt option there was a selection for a Toshiba based restore. That is the one I tried that failed at 98-99% This system recovery just has the standard options. At first it showed me the original OS of Home Premium (recovered). I tried to repair the Home Premium and it still wouldn't work. "Startup could not repair the problem". On the many tries the probelms were either "Failed Installation" or "Partition Table". Then when I tried loading the OS it would blue screen and reboot repeatedly. So I loaded up Windows 7 Professional from a different CD to at least get the OS working. I tried Repairing but that didn't work with the same errors, and it also reported that there was no system image on the disk. I did a Custom (fresh) install and had all items copied to Windows.Old folder. So now I have an OS, BUT I can't activate it now even with the keys that I have from the old version because it said the key was only used for upgrade, not clean installs. So now I'm left with trying to find a way to get the original Home Premium image so I can load that and then upgrade since I have the keys I need. I tried doing repairs again, this time it showed me two Windows 7 Professional and one Windows 7 Home Premium. Again I tried repairing the Home Premium but it came back with the same errors. Now all that remains is just the fresh install of Windows 7 Professional that I installed but can't activate with the key. Anyway I can get/download a factory image from Toshiba? I only just bought the laptop shortly before Christmas.

Windows 8.1 Pro will not boot after installing iTunes 11.1.5.5

It's a little hard for me to accept that this is true, but the symptoms seem to be pointing the direction of the title of this thread. I have an all-in-one touch-screen Gateway computer that came with windows 7 (yeah, a win7 machine that came with touch, yeesh) and I put windows 8.1 pro 64-bit on it with a clean install (actually windows 8 was the clean install and then I did the free microsoft store upgrade to 8.1). It has 4GB of RAM and has a Pentium Dual Core cpu @ 2.2 Ghz. It was running fine with the previous version of iTunes, but as soon as I updated to iTunes 11.1.5.5 (and there may have been other apple things that updated too (ie quicktime of course), the computer prompted me for a reboot and froze during the reboot process (before it even shut down). Then it had trouble booting into windows. I ran startup repair to no avail and decided to do a sytem restore. My most recent restore point was from a few weeks back, before iTunes was even installed at all on the machine. I went back to that point and the machine worked fine again. Then I installed iTunes 11.1.5.5 and the same exact problem occurred - it froze while shutting down after the iTunes install and then would not boot into windows 8. I did another system restore and have not put iTunes back on. The system is working fine. I'm going to try to find out if there's a way to download older versions of iTunes, so that I can install it, but the bigger issue here is: Is this a legitimate bug/incompatibility with some hardware or software or driver that I have on this computer? I run a computer support business so I know my way around but I don't have time to troubleshoot this from scratch. Anyone else seeing this? Apple employees...a little help here? Any input?

let it sit for about 30 min and still got nothing
I then did a "hard shutdown(just pressed power button till it turned off the computer)"
That may not have been long enough. But a "hard shutdown" would definitely have been construed as a problem due to the update.
Asus apparently is a known problem case...
http://blogs.msdn.com/b/usbcoreblog/archive/2013/10/19/help-after-installing-windows-8-1-the-superspeed-ports-of-my-asus-system-don-t-work.aspx
Link courtesy Darrell Gorter [MSFT] found here
"Windows 8 Keyboard and mouse not working"
http://social.technet.microsoft.com/Forums/en-US/w8itprohardware/thread/06e9b341-0619-4085-acbf-e2f0133ca428?outputAs=rss
(RSS given to avoid overhead of opening long thread for IE users)
Note that there may be useful tips for you in both of those threads' comments.
Robert Aldwinckle

Not booting from 10.4.8 volumes after upgrade from 10.4.7

I'm sorry to report that my aged G4 450 MHz AGP with 4 internal Hard disk drives no longer boots from any of the 2 volumes upgraded to Mac OS X 10.4.8 as soon as it was started from another volume!
All was working fine as long as 10.4.7 was installed on the 2 232 GB disks connected to the SIIG ATA133 controller. I could boot from any OS on any of the 4 disks, 5 partitions:
internal ATA66 bus:
18 GB disk, 2 partitions: 'IBM_18GB' with OS 9.2.2 and TechTool Pro's 'eDrive' with 10.4.7
71 GB disk, 1 partition 'IBM_71GB' with OS 9.2.2
PCI SIIG ATA133 controller:
232 GB disk, one partition 'I1232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
232 GB disk, one partition 'I2232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
Now I can only boot from the Mac OS 9.2.2 or the eDrive 10.4.7 partitions.
What I did so far: 'I2232GB' was my main OS X startup volume, 'I1232GB' contains a clone of it, plus additional folders like software base and backups.
After upgrading 'I2232GB' to Mac OS X 10.4.8 through Software Update and repairing permissions all was OK as long as the Mac was just shut down or re-started: it always booted up in Mac OS X 10.4.8 from 'I2232GB' without any problems.
The next day I booted from 'I1232GB' to do the same there.
Afterwards I could no longer boot in Mac OS X 10.4.8 from 'I2232GB' nor in in Mac OS X 10.4.8 from 'I1232GB': it just gets to the grey screen with the Apple logo, but the round circle underneath indicating some progress never appears. I left it there for hours: it just hangs.
With the Option key held at startup I could boot from the other partitions with Mac OS 9.2.2 or the eDrive with 10.4.7. None of their Startup Control Panels was able to get me back to 10.2.8!
So I booted from the TechTool Pro 4.5.1 DVD to Optimize both volumes, 'I1232GB' & 'I2232GB', always Files only.
Then I booted from the DiskWorrior 3.0.3 CD to rebuild the directories of both volumes, 'I1232GB' & 'I2232GB'.
Still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
Downloaded the Mac OS X 10.2.8 Compo Update (for PPC) and installed it onto both 'I1232GB' & 'I2232GB' while booted from the eDrive which I keep on Mac OS X 10.4.7 - no luck either, still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
Then I backed up the users folder from 'I2232GB' onto 'I1232GB', booted from Mac OS 9.2.2 and used Intech's Hard Disk Speedtools 3.6 to format 'I2232GB', afterwards initialized it with Alsoft's Plus Maximizer Extension for a Block Size of 512 Bytes.
Installed Mac OS X 10.4 from DVD, as well as iLive '06 and upgraded everything to the latest releases with Software Update. All was working fine with all the required reboots until another startup volume was chosen: afterwards again I can no longer boot back into Mac OS X 10.2.8 on the fresch installed 'I2232GB'!
Any help would be appreciated.
Here is some information found by System Profiler from Mac OS X 10.4.7, eDrive, let me know if you need more:
Hardware Overview:
Machine Name: Power Mac G4 (AGP graphics)
Machine Model: PowerMac3,1
CPU Type: PowerPC G4 (2.8)
Number Of CPUs: 1
CPU Speed: 450 MHz
L2 Cache (per CPU): 1 MB
Memory: 2 GB
Bus Speed: 100 MHz
Boot ROM Version: 4.2.8f1
Serial Number: XA00715VHSF
Sales Order Number: M7628LL/A
ATA Bus:
IBM-DPTA-372050:
Capacity: 19.12 GB
Model: IBM-DPTA-372050
Volumes:
IBM_18GB:
Capacity: 13.12 GB
Available: 6.96 GB
eDrive:
Capacity: 6 GB
Available: 3.03 GB
IBM-DTLA-307075:
Capacity: 71.59 GB
Model: IBM-DTLA-307075
Volumes:
IBM_71GB:
Capacity: 71.59 GB
Available: 39.65 GB
ATA Bus:
PIONEER DVD-RW DVR-107D:
Model: PIONEER DVD-RW DVR-107D
Firmware Revision: 1.21
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
IOMEGA ZIP 100 ATAPI:
Model: IOMEGA ZIP 100 ATAPI
ACARD,6880M:
Name: ACARD,6880M
Type: scsi
Bus: PCI
Slot: SLOT-C
Vendor ID: 0x1191
Device ID: 0x0009
Subsystem Vendor ID: 0x1191
Subsystem ID: 0x0009
Revision ID: 0x0003
SCSI Parallel Domain 65536:
Initiator Identifier: 7
ATA HDT722525DLAT80:
Capacity: 232.89 GB
Manufacturer: ATA
Model: HDT722525DLAT80
Revision:
Removable Media: Yes
BSD Name: disk2
OS9 Drivers: Yes
SCSI Target Identifier: 0
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
Volumes:
I1232GB:
Capacity: 232.89 GB
Available: 14.1 GB
Writable: Yes
File System: HFS+
BSD Name: disk2s3
Mount Point: /Volumes/I1232GB
ATA HDT722525DLAT80:
Capacity: 232.89 GB
Manufacturer: ATA
Model: HDT722525DLAT80
Revision:
Removable Media: Yes
BSD Name: disk3
OS9 Drivers: Yes
SCSI Target Identifier: 2
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
Volumes:
I2232GB:
Capacity: 232.89 GB
Available: 180.11 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk3s3
Mount Point: /Volumes/I2232GB
The RAM consists of 4 identical modules and is about 1 year old:
DIMM0/J21 to DIMM3/J24:
Size: 512 MB
Type: SDRAM
Speed: PC133-333
Status: OK
Many thanks for your help!
Josef
Apple G4 AGP Mac OS X (10.4.8) 4 internal hard disks, dual layer DVD-RW, 2GB RAM

What I did so far: 'I2232GB' was my main OS X
startup volume, 'I1232GB' contains a clone of it,
plus additional folders like software base and
backups.
After upgrading 'I2232GB' to Mac OS X 10.4.8
through Software Update and repairing permissions all
was OK as long as the Mac was just shut down or
re-started: it always booted up in Mac OS X 10.4.8
from 'I2232GB' without any problems.
The next day I booted from 'I1232GB' to do the same
there.
Afterwards I could no longer boot in Mac OS X 10.4.8
from 'I2232GB' nor in in Mac OS X 10.4.8 from
'I1232GB': it just gets to the grey screen with the
Apple logo, but the round circle underneath
indicating some progress never appears. I left it
there for hours: it just hangs.
With the Option key held at startup I could boot from
the other partitions with Mac OS 9.2.2 or the eDrive
with 10.4.7. None of their Startup Control Panels was
able to get me back to 10.4.8!
So I booted from the TechTool Pro 4.5.1 DVD to
Optimize both volumes, 'I1232GB' & 'I2232GB',
always Files only.
Then I booted from the DiskWorrior 3.0.3 CD to
rebuild the directories of both volumes, 'I1232GB'
& 'I2232GB'.
Still I can not boot from either 'I1232GB' or
'I2232GB' in Mac OS X 10.4.8!
Downloaded the Mac OS X 10.4.8 Compo Update (for PPC)
and installed it onto both 'I1232GB' & 'I2232GB'
while booted from the eDrive which I keep on Mac OS X
10.4.7 - no luck either, still I can not boot from
either 'I1232GB' or 'I2232GB' in Mac OS X
10.4.8!
Then I backed up the users folder from 'I2232GB'
onto 'I1232GB', booted from Mac OS 9.2.2 and used
Intech's Hard Disk Speedtools 3.6 to format
'I2232GB', afterwards initialized it with Alsoft's
Plus Maximizer Extension for a Block Size of 512
Bytes.
Installed Mac OS X 10.4 from DVD, as well as iLive
'06 and upgraded everything to the latest releases
with Software Update. All was working fine with all
the required reboots until another startup volume was
chosen: afterwards again I can no longer boot back
into Mac OS X 10.4.8 on the fresch installed
'I2232GB'!
I found several typos in above post, wherever it was 10.2.8 it should have read 10.4.8 - I'm very sorry for confusing you, this would not have made sense, but I found no way to edit the existing text therefore I modified the quote of it here.
I do not need Mac OS X 10.2.8 back, but it would be nice to boot back in Mac OS X 10.4.8 from another volume as the current one - which was working fine before with Mac OS X 10.4.7.
Many thanks,
Josef

K7N2 Delta not booting

My K7N2 Delta was working fine. Then it start emitting an aduible alarm. I turned of the machine, and it happened again. Now it will not boot. My screen is dead. My D-Bracket lamp shows CPU failure but I have swapped the CPUs. Still no joy. ;( I have cleared the CMOS, no joy. What next ?

uphaze,
If your heatsink and fan hooked up correctly?
Take Care,
Richard

Please help! MBP 15" 2011 will not boot at all

Hi,
My 15 inch early (May) mbp 2011 will not start up. Here is what I have observed so far:
1) When power button is pushed (without MagSafe attached) hard drive will spin up and about after 3-5 seconds it will turn off (hard drive spins Down, no further boot process) No chime, no led indicator light in front.
2) When power button is pushed (with MagSafe attached) hard drive spins up, keeps spinning, but no further boot process. Just black screen and spinning hard drive.
3) When attempting SMC reset, fans turn to high, and screen remains black, still no boot)
4) Since mbp fails before booting, PRAM/NRAM resetting is not a possibility. (Tried)
5) I have also removed the battery cable from the logic board, and tried resetting without any luck.
6) I entered CD into optical drive - it "ate" it, but will not eject now. (Tried holding eject/left mouse/control e etc) still nothing.
7) After letting mbp rest for 1 day, it booted fine like nothing happend, worked fine for 1 day, then next morning back to square one. Now 5 days later still nothing.
If anybody has any ideas what could be wrong, or have possible solutions, please don't hesitate.
Thanks in advance, Oliver

Hey there Oliverkehn,
It sounds like your computer is not booting up at all at this point, even after some very thorough troubleshooting you've already done. From the following article, I would use these steps that I don't mention as having been tried just yet:
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/ts1367
Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
MacBook Pro: How to remove or install memory
MacBook: How to remove or install memory
Mac Pro: How to remove or install memory
Mac mini: How to remove or install memory
iMac (27-inch, Late 2012): Installing or replacing memory
iMac: How to remove or install memory
If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
Thank you for using Apple Support Communities.
Regards,
Sterling

T400 not booting at all.

My T400 is not booting at all.
When I power it on, no matter it's on AC or battery, it just shows the boot screen
Black Screen with Thinkpad written (in BIG white letters).
and "To Interrupt normal setup, press the blue ThinkVantage button"
I tried pressing Thinkvantage button nothing happened.
I also tried pressing all function Keys, from F1 to F12... nothing happened
I am not too sure what went wrong, I am on travel and needed my laptop badly.
not sure what to do can anybody help me please.
System Configuration:
T400, 2 GB RAM,
Windows XP SP3,
Just one Partition on hard disk C drive.
How did this happen:
I am also not too sure but I remember few things that I did last, and mentioning them here,
not too sure if this has got something to with the problem that I am facing...
1. I compressed my C drive.
2. I had hibernation enabled ...disabled it...shutdown-ed the machine
3. Next time when i rebooted machine..i was in flight....I did work that i wanted to do ,,then enabled hibernation...
and hiberanted...
4. Before hibernation could have completed .... i closed the flap..and kept it in bag...
5. later on when i powered it on ...its not booting at all

I don't tell what caused your problem ( there are more knowledgable people here for it) but it is not wise to do these alterations you mention on a trip - better try things at home with a recent backup

Tecra A11-11N does not boot after CPU upgrade

Hi,
I would like to do a processor upgrade for my Tecra A11 11N from the i5-430M to a probably much faster i5.I thought the i5-580M would do, but the laptop did not boot when i installed this processor.
I reverted back to the 430M, did some research on the internet and found out that the 580M has a very high FSB speed and that is what probably made it not to work/incompatible with my machine.
http://ark.intel.com/products/43537/
http://ark.intel.com/products/49653
http://ark.intel.com/products/49652
and also at http://ark.intel.com/
Now i went back to the computer shop,returned the 580M and got an i5-560M as i compared it's specs and saw it would be compatible as it has the same FSB speed with the 430M.
I then later on in the day tried to install this cpu as an upgrade BUT alas!
It STILL WON'T BOOT ALSO.
I was left dumfounded.Processors in the same familly line are supposed to be compatible with one another provided:Lithography, FSB and socket type are similar.
Or what am i missing here?
I have done processor upgrades in many instances for both desktops and laptops and this is the first one that has left me with no words to say!
please offer some help/advice.
Simon
+Message was edited+

I solved this processor upgrade problem on my own.
I did some little research on what limits processor upgradability on computers and i
found out that BIOS was one of the factors that play a key part.
So,i went on a mission
to see if i could upgrade my BIOS and whether it would solve my problem.
I found this link to be very informative:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=66624
I then downloaded the latest BIOS version for my laptop from this link:
http://uk.computers.toshiba-europe.com/innovation/download_bios.jsp
The following link gave me proof that the BIOS update would not bring any problems to my
machine and that there is already someone who had done it and not encountered any problems.
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=62459
Just to make sure that you are on the safe side,before carrying out the procedure to update
your BIOS,make sure you have a fully charged battery in addition to the AC plugged in.A power
outtage during this procedure would instantly kill your machine.
The BIOS installation took less than 3 mins.I copied the executable on the desktop and run it
from there.
On rebooting,the new BIOS was installed.The new BIOS version was 3.40 dated on 05/18/2012 while
the older one was version 2.0 dated on 04/03/2010.
From Intel's website,the i5-430M was released on Q1 2010 while the i5-560M and i5-580M were
released on Q3 2010.
It is pretty obvious that by the time BIOS version 2.0 was release,these two newer processors
had not been released and that explains why they were not being recognized when i installed them.
I finally swapped the 430M with the 560M,assembled back the machine and powered it.
Voil!,the machine booted to it's new life.Everything is as was before!
So far i have not seen any problems even to do with overheating or the cooling fan spinning any
faster that before.It is all the same as before.There is considerable performance gain with the
uprade.I am a software developer and my various development enviroments including compilers,
debuggers,database and deployment servers have all been running way way faster than they were!
I believe the 580M can also work but unfortunately i had returned it back to the shop.
There is no reason for buying new machines when we can upgrade the ones we have.What will
happen to the older ones?This means more electronic waste and so does new machines.Let us try
to make better use of the ones we have a in turn,SAVE OUR ONLY PLANET EARTH FROM GLOBAL WARMING!

My apple tv 1st gen will not boot up the light just keeps flashing yellow

I turned the power on to my 1st gen apple tv about a week ago and the indicator light just kept flashing yellow it would not boot up I tried unplugging it letting it cool and plugging it back in, I left it plugged in for the day and it still wouldn't boot, I listened for hard drive clicking there was none, I looked at the Ifixit teardown and saw what looked like a CMOS battery, I've had a pc before with the same symptoms and replaced the battery and everything worked fine after. If anyone can provide a second opinion it would be much appreciated.

Welcome to the Apple Community.
The most likely problem is a hardware failure.

Macbook Air mid-2013 suddenly not booting - showed battery icon then died

Hi all,
This morning, I used my Macbook Air (mid-2013) to send an email and check up on my usual stuff, nothing I've not done hundreds of times. I then closed the lid and went to work. Again, nothing I've never done before.
When I got home though, I opened the Macbook and it didn't wake up, which I thought was odd. So I pressed the power button. For a few seconds, it showed an icon in the middle of a black screen that was related to the battery - sorry I can't recall exactly what it looked like, its the first time I've seen it, but it showed an empty battery with a small red part of it left - obviously understood as meaning the battery was flat.
I was puzzled at this; it should have been asleep since I'd closed the lid, how could it have run out? I was only gone for about 8 hours as well, I usually get more battery life than that out of it when I'm actually using it, never mind when its sleeping.
But I thought whatever, and plugged it in for a few minutes to charge it up enough to turn on and maybe see why it had done this. The orange light came on the Magsafe end, but after a few minutes, still nothing.
Cue much panicking and looking around at things, and this is what I've discovered/tried:
- The battery appears to be charging, the light eventually went green.
- When I press the power button, the Mac does power on; I can hear the fan inside if I put my ear to it (note that this means its really quiet, its not blowing at full power or anything), and the Mac is getting hot on the left hand side where the power adapter plugs in. It turns on both when plugged in and when its not. So the battery has power and the machine is turning on, it just isn't booting or doing anything. I can turn it off if I hold the power button down for about 3 seconds, the fan stops. But everything else is completely unresponsive. Also, it gets quite hot pretty quick, hotter than it normally does when in use.
- I've reset the SMC, several times. When I do this, the light on the Magsafe goes green for a second, then back to orange, as though I've just plugged it in. I guess this means it is responding to the SMC reset, but it does nothing in terms of getting the thing started. This is the first thing people suggest with this problem, but I've already done it and while it seems to be doing its thing, it doesn't fix the problem.
- I've tried resetting the PRAM/NVRAM. This has no noticeable affect on anything.
- I've tried holding a bunch of different keys when starting up (cmd+R etc.) but again, nothing.
- I've tried something crazy suggested in another thread; leaving the Macbook partially opening and shaking it, which supposedly does something to the "sudden motion sensor". I wouldn't have tried this but a whole bunch of people said it worked for them, but it does nothing for me. The fact this step didn't work is why I made a new thread; because the issue with those people seemed to be that their Macs wouldn't wake up from sleep/hibernation and shaking it somehow did that, or they just magically woke up on their own.
And at this stage I seem to have run out of thing to try.
I've made an appointment at the Genius bar but the earliest they could do is Saturday, which is pretty crappy and I'm going travelling in less than 2 weeks, so I really need my Macbook to sort out the details since a lot of info about it is on there exclusively.
Does anyone know any reason why this might have happened?
Why would the battery drain so fast when it was supposed to be sleeping?
Why will it now not boot at all, even though it's powering up in some way? Could it not booting be related to the fact the battery seemed to run completely flat, and this has done something to the software or hardware?
Any suggestions beyond what I've tried already?
If I can't get it working before my Genius appointment, I'll post what happens here just in case any one else has this issue so people will have an idea of what might have happened to them.
Thanks in advance!

olliemilne wrote:
- I've tried holding a bunch of different keys when starting up (cmd+R etc.) but again, nothing.
You could try booting the MBP using the OPTION+COMMAND+R keys and see if it will connect to the Apple servers. This would allow you to install the original OSX . I have my doubts though.
- I've tried something crazy suggested in another thread; leaving the Macbook partially opening and shaking it, which supposedly does something to the "sudden motion sensor".
The Sudden Motion Sensor is applicable for conventional Hard Drives, not the SSD that is in a MBA. Doing that will serve no useful purpose.
You have exhausted all reasonable options and will just have to have the MBA evaluated at the genius bar.
Ciao.

OS 9 Not booting in 10.3.9

Similar Messages

Maybe you are looking for