Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC has been turned on (PC is connected via Ethernet cable, and has no wireless capability as far as I know). What gives? It works fine when the PC is off.
Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC is on (the PC is connected via Ethernet cable, and has no wireless capabilities that I know of). What gives? When the PC is turned off, everything is totally fine. I\m stumped.
Does the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
I suspect a problem with your router. Try changing the security. First use no security as a test.
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Similar Messages
-
My Apple TV will not update to the latest software, dose anyone know what the problem is, I've reset, tried to do it wirelessly as well as while connected via Ethernet cable.. Both have resulted in the same message!! Update unsuccessful, current software version is 5.1 (5201) . I've rented a movie recently and does not appear in my movie list, but I have been charged for this movie, can someone help me out with these issues.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Source list, and then click Restore.
If when you choose restore you get a message that the device cannot be found, download the file below
Apple TV Software Restore 5.1.1 (2nd generation)
Apple TV Software Restore 5.1.1 (3rd generation)
Then hold down the option key while choosing restore and select the downloaded file when prompted. -
Have new Airport Extreme conneted via ethernet cable from HughesNet Gen4 modem. Using NetGear WN3500RP extender. NetGear asks for different names for the 2.4 and 5 GHz bands. Most of what I have read indicates extender should have same name as main network? How is it best to configure with the Airport Extreme router 802.11ac?
Different names for the 2.4 and 5 GHz networks are optional, but can be convenient for you to distinguish one from another. It's up to you.
-
I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning great. The network name I assigned to the TC is also not appearing among available networks. How do I remedy this, please?
What OS on the computer you are using to setup the TC?
Did you turn on ipv6 for wireless to link-local... this is essential for network access now??
Try power cycling the network.. start up in correct order.. uverse.. 2min wait.. TC.. 2min wait.. computer.
No luck factory reset and start over. Use ethernet cable as well to the computer to help it.
No luck I can show you manual method. -
I have an HP LaserJet 8150N that I use for my work and I have had this printer for ever and it is one heck of a work horse! I am trying to get it connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer. I have tried to reconfigure the printer using the JetDirect menu giving it a new IP address but still no luck. If anyone could help me through this issue I would appreciate it.
moonlightcaravan wrote:
Second, seeing "connecting" and connection failed is normal. You must click on "Connect As" in the Finder window and then enter the username and password for the admin account on the other computer. That should fix things.
Thanks for responding.
When does clicking on "Connect As" happen in the process above?
After step six? Seven?
After the connection has failed?
Is this the FInder window that shows the icon of the computer you want to copy the file from?
You should see "Connect As" in the Finder near the top right of the window as shown below:
!http://blog.brothersoft.com/wp-content/uploads/2008/11/howto_copy_files_to_or_from_your_iphone02.jpg! -
I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260 -
Hi, I recently upgraded my MBP (m2009) to Mavericks and now my 2nd HDD (internal optical bay) is no longer recognized. It was fine before upgrade and works fine when I hook up externally. Very strange. HDD cable appears fine. It does not show up in Disk Utility either. Appreciate any ideas. Thanks.
Hi, I'm back home. Here's the info:
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *120.0 GB disk0
1: EFI EFI 209.7 MB disk0s1
2: Apple_HFS Mavericks SSD 119.7 GB disk0s2
Does this help?
Thanks. -
Trying to connect my xbox to the airport express. Have wireless in home and do not have a ethernet point behind tv/xbox. How do I configure the airport express to connect to my wireless network and then the airport express can use its connection via ethernet to connect the xbox to the internet.
Is your AirPort Express Base Station (AX) a 802.11n model? If it is, you can reconfigure it as a wireless Ethernet bridge or ProxySTA. This would allow the AX to join another wireless network and have its Ethernet port enabled for wired clients, like the Xbox 360.
To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility. -
Just upgraded to I-Photo 11 but now cannot import my photos anymore from my Nikon digital camera to my MacBook. Worked fine until the upgrade.The camera first shows a message "ready to import", then a message "communication error".Thanks for any suggestions?
Thank you, Terence, the USB Card Reader solved my photo import problem. It is also soooo much easier.
helgg -
Hi, when I try to download an application the app stores downloads it for about 2 seconds and then it stops downloading it! I don't know what's wrong?
Try This...
Close All Open Apps... Sign Out of your Account... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... (But can take Longer..)
Release the Buttons...
If no joy...Reset all settings
Settings > General > Reset > Reset all Settings.
This will return all iDevice settings to factory defaults... you will not lose any data.... But you will have to re-enter all of the device settings. -
I've been hacked and I changed my password but he still finds away to get into my Game Center and change my bio. I need serious help
Have you given your information to anyone? Family, friend?
Did you have another device with Game Center on it? Did you give a new owner of a device any passwords?
Do you share apple account with a family member?
Do you have a rescue email set up in your Apple account, with security questions?
I suggest you set up a new email account, write everything down and keep it in a safe place.
New email account and password. Not so easy that it can be hacked.
In your iTunes account on the computer. Login and change security questions, password and rescue email.
Again, make sure your password is not easy to guess. Same with security questions.
Write it all down and keep it somewhere safe.
I recommend a password keeper called Enpass. You can store 10 cards with user names, passwords, notes and account numbers in the free version.
Then you only have to remember one complicated password to open Enpass and retrieve your information.
If all else fails, contact apple support. -
Im at a loss here, even switched cables thinking that would help. no luck either
Cpress1 please see Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html for several possible solutions for your current download error. I would also recommend looking at any software firewall or security software which you have installed that could be interfering with the download process.
-
I want to buy a hard case for my macbook pro, but I don't know what year it is. When I use the serial number to try and find out, all it says is, "~VIN,MacBook Pro (15-inch Glossy)". When I type that into amazon for a case it gives me nothing!
Hi T,
Either of these will give you the info you seek:
http://www.appleserialnumberinfo.com/Desktop/index.php
http://www.chipmunk.nl/klantenservice/applemodel.html -
hi. I have the ipad 4 and have got a Vodaphone ( India) data sim, however it does not seems to work. The CS support at the gallery and the call center is lousy as they dont seem to know what they are upto. Although the sim is active i am unable to surf. The vodaphone number is
9168554687. Please assistSince this is a carrier issue, we are probably not going to be able to help you. You are paying for this service, so be assertive when you call customer service.
-
Okay so i was updating someone picture in my contacts it kept loading for a long time so i held the home button and the power button it slowly went black like it faded out and went black i tried everything i dont even know what wrong i been had a crack on my phone and like i can see thats its light so like what do i do cause i tried plugging it into the computer and stuff and the computer dosent even bring up the logo which means the computer dosent reconize that my iphone is plugged in i had this problem before except it went white pleaase help
Hi supreme_babes,
If the display on your iPhone is black or isn't responding, you may find the following article helpful:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Regards,
- Brenden
Maybe you are looking for
-
How do I get new fonts to show up in Reports?
I can't get my v10 reports to display MICR font on the server. I have a MICR font that I installed without issue on my PC. When I write something in the 10.1.2.0.2 Report Builder, it comes up in the MICR font without issue. We have a Windows server A
-
Need help ASAP with photoshop elements 11
Please I need help its photoshop elements 11 but I can't put up the pic I need help with could someone help me out by using Facebook, Amanda Jayne Clarke I have a pic of a little girl n a horse Please i need help ASAP
-
Ipod missing songs after update
I never should have done this but when I updated my itunes recently and left auto-sync on. Plugged my ipod in, itunes takes the next 6 hours trying to update my ipod with 40 gigs of music. It was able to do it, and it shows all songs as being importe
-
Business area in asset retirement
Hi, While retiring the asset(t.code F-92), we get an error message "Account assignment not possible (Asset not assigned to a business area)". But in asset master(time dep tab), business area is assigned to the asset. The version is 5.0. What should b
-
Iphone 4 problems after 7.0.2 update--Especially with keyboard entries
I am having serious iphone 4 problems after installing the 7.0.2 update. Mostly it is with use of the keyboard. Each key stroke takes about 8 seconds to show. It is truly disabling. Apparently many others have had various problems. The one thing